Search Documents

By A. C. Polk, R. H. Smith

The physical properties of the materials are listed, together with a short explanation of how this material binds the sand grains together without materially reducing the effective permeability of the sand. The chemical can be used in wells with bottom-hole temperatures ranging from 105°F to more than 350°F A description of the equipment required and the techniques used for applying these plastics to the wells is included. Introduction Recovering oil and gas from unconsoli-dated sand formations offers one of the most troublesome of all production problems. These sands generally present no particular trouble while drilling is in progress, but after the well has been completed and a pressure differential has been established across the face of the producing zone, the formation begins to L'slough," resulting in "sanding up" of the well. The term "sanding up" means that sufficient volumes of sand have moved into the well bore or casing to cause a serious reduction or complete halt of all flow of oil, water or gas. In rare cases a well may produce only a small amount of sand and still continue to flow or pump, the sand being carried to the surface in the fluid stream. However, in such instances, the result may be a costly repair bill due to the effect of the sand on surface and pumping equipment. The difficulty of producing petroleum from sands that are loosely cemented has long been recognized by petroleum engineers but only within the last few years has any new approach to the problem been undertaken. This involves the use of plastics that are capable of bonding the individual sand grains in place without materially reducing the effective permeability of a formation. The successful application of plastics for the consolidation of poorly cemented sands is relatively recent but now it is widely used in many of the more difficult areas on the Gulf Coast of Texas and Louisiana. This relatively new use of plastics1 in the oil fields has been preceded by much laboratory and field research on the use of various chemicals2,3 for solving numerous well-completion and work-over problems. Plastics now are being used successfully to control gas-oil and water-oil ratios,4'6 in zone isolation, the repair of casing leaks, the elimination of caving in cable-tool drilling wells6'7 and in the setting of linerss and casing.9 Sand-consolidating plastics, however, are basically different from all others in that they must not form an impervious seal. Field Practices The approach to the sanding-up problem usually has been the mechanical obstruction of the movement of the sand grains.

Jan 1, 1947

By R. W. Mancantelli, J. R. Woodward

IN 1947 a large low grade deposit of uranium was located in the northwest corner of Saskatchewan, in the Beaverlodge property of Eldorado Mining & Refining Ltd. Most of the values occur as thin seams and as coatings on other minerals, and the ore, which is light and friable, is not amenable to the usual gravity methods of concentration. The acid leaching process developed to retreat the company's Port Radium tailings was also impractical, as the percentage of carbonates is high and the percentage of sulphides relatively low. Construction of the mill building and installation of equipment, both scheduled for 1952, awaited selection of a satisfactory ore dressing process on or before Oct. 1, 1951. An extensive research program on dressing of ores from the Ace mine therefore was undertaken by the Mines Branch in Ottawa, a research team at the University of British Columbia, and an ore dressing group at the company's Port Hope refinery. Pilot plant operations were conducted at the Ottawa plant of Sherritt Gordon Mines Ltd. under the general direction of C. S. Parsons, consultant on metallurgy and ore dressing for Eldorado. In mid-September, having compared results of the several research programs, Dr. Parsons recommended a process employing a carbonate or basic leach. He reported that, while the chemistry of the process had been proved, engineering of the flowsheet was incomplete, and he suggested that under normal conditions further pilot plant work at the Ace mine might be profitable. However, since this would involve a delay of 12 to 18 months in bringing the property into operation, he recommended that design of the concentrator proceed immediately. Concentrator capacity was determined by two considerations: 1) the amount of ore then available and 2) the expectation that continued improvements would be made in the ore dressing process as a result of the intensive research being carried out by the Mines Branch of the Department of Mines and Technical Surveys. As these improvements could affect both the chemistry and the en-

Jan 1, 1956

By W. T. Weller

In Part I, a study of pressure build-up curves calculated for conditions under which both oil and gas flow led to the conclusion that the presence of a dispersed free gas phase in an oil reservoir must be taken into consideration to estimate accurately average reservoir pressure and permeability from build-up curves. Familiar methods based on the assumption of no free gas can be extended to the two-phase case by using total compressibility and mobility in place of single-fluid compressibility and mobility. These methods give correct values for average pressure and permeability when gas saturation is small. Errors become larger as the gas saturation increases. However, for the use to which the results will be put, the methods are satisfactory for reservoir engineering purposes. An improved method of calculating the performance of depletion-type reservoirs is presented in Part 2. Because the mathematical relationships describing simultaneous flow of oil and gas are quite involved. simplifying assumptions are made to provide means of obtaining approximate solutions of reasonable accuracy. One such approximate method now in use is the constant-GOR solution. It involves the assumption that at any instant, the ratio of total gas flow rate (both free and disolved) to oil flow rate is the same at all points in the reservoir. The approach is not applicable unless the free gar saturation in the reservoir is everywhere greater than the critical gas saturation. This paper presents a modification which, by avoiding the constant-GOR assumption, makes the method applicable to all reservoir conditions, and so far appears to be more accurate than the constant-GOR solution and to he comparable in required compuctation time. PART I— BUILD-UP CURVE ANALYSIS INTRODUCTION Pressure build-up characteristics of shut-in wells have been used for many years by engineers to evaluate average reservoir pressure, effective permeability thickness of the pay section, effectiveness of well completion (skin effect) and reservoir size. A number of methods of analysis have appeared from time to time."" Without exception, these methods are based on the assumption that the reservoir contains but one fluid of constant small compressibility and constant mobility. It has been suggesteda" hat these single-fluid methods may be applied to data from reservoirs containing both oil and gas by substitution of some effective total properties of the multiphase system in place of the corresponding single-phase properties. The present investigation was undertaken primarily to evaluate this approach. METHOD A number of theoretical build-up curves were calculated for conditions of two-phase flow, under the assumption of certain reservoir and fluid properties, and were analyzed by single-fluid methods with appropriate total compressibility and total mobility values for the corresponding single-fluid properties. Results of the analyses were compared with the assumed conditions. The theoretical build-up curves were completed by procedures similar to those of West, Garvin and Sheldon." Since these calculations require a considerable amount of computer time, an attempt was made to derive an approximate calculation method. The attempt was unsuccessful for calculating build-up curves, but the effort did result in a new approximate method of calculating the performance of solution gas drive reservoirs, which appears to be an improvement over the constant-GOR method" used previously (see Part 2). The West, Garvin and Sheldon calculations involved the following assumptions: (1) the reservoir is circular and completely bounded, with a completely penetrating well at its center; (2) the porous medium is uniform and iso-tropic, with a constant water saturation at all points; (3) gravity effects can be neglected; (4) compressibility of rock and water can be neglected; (5) the composition and equilibrium are constant for oil and gas; (6) the same pressure exists in both the oil phase and the gas phase; and (7) no afterproduction occurs, i.e., the well is shut in at the sand face for build-up. These assumptions make it possible to describe two-phase flow of oil and gas by the partial differential equations:

Jan 1, 1967

By F. H. Daniels

IN this, paper it is my intention to, call your attention to* a few of the many producers using blast, now, in common use in Sweden, and also those constructed by the Washburn & Moen Manufacturing Company at their Quinsigamond Works. During a prolonged stay in Sweden the writer had an opportunity

Jan 1, 1881

By J. L. Jernegan

In this paper I propose to give a short and, I must confess, a rather incomplete description, as regards many details, of the process used in Chicago, Ill., for smelting the argentiferous ores of the far West, and shall confine myself in this description, principally, to the process used at the Chicago Silver Smelting and Refining Company's Works, known as the Balbach process, as all the other smelting works in that city follow the same method, with the exception of one, which has the Cordurié process for the desilverization of argentiferous lead. In all, there are five silver smelting and refining works in and near the city of Chicago. The Chicago Silver Smelting and Refining Company's Works are situated at the little station of South Lynne, about seven miles south from Chicago. The plant at these works consists of one horizontal steam-engine, principally used for running the ore pulverizer, four reverberatory smelting-furnaces, connected by horizontal flues with a common chimney 85 feet high, three lead-softening furnaces, one so-called zinc or mixing furnace, one separating furnace or liquation hearth, one lead-refining furnace, three zinc distillation retorts, one English cupellation furnace, supplied with blast by a No. 3 Sturtevant blower, which is run by a small steam-engine having a vertical tubular boiler, and an assay office, in which there are two windfurnaces of the ordinary construction, and also a small muffle furnace. The assay office is supplied with all the necessary apparatus and reagents for fire assaying. There are also a superintendent's office, various store-rooms for coke and charcoal, and for the preparation of fire-clay, etc. Recently a small slag hearth (Krummofen) with one tuyere, has been put up for the purpose of working over such slags as assay too high in silver and lead to be thrown away, of which there are large amounts. The principal ore worked while I was in the employ of the company was that of the well known Emma mine in Utah, and also small quantities of Colorado ore. The character of the Emma ore is well known to most members of the Institute. In consists principally of ferruginous mixtures of carbonate and oxide of lead, oxide

By J. L. Jernegan

IN this paper I propose to give a short and, I must confess, a rather incomplete description, as regards many details, of the process used in Chicago, Ill., for smelting the argentiferous ores of the far West, and shall confine myself in this description, principally, to the process used at the Chicago Silver Smelting and Refining Company's Works, known as the Balbach process, as all the other smelting works in that city follow the same method, with the exception of one, which has the Cordurié, process for the desilverization of argentiferous lead. In all, there are five silver smelting and refining works in and near the city of Chicago. The Chicago Silver Smelting and Refining Company's Works are situated at the little station of South Lynne, about seven miles south from Chicago. The plant at these works consists of one horizontal steam-engine, principally used for running the ore pulverizer, four reverberatory smelting-furnaces, connected by horizontal flues with a common chimney 85 feet high, three lead-softening furnaces, one so-called zinc or mixing furnace, one separating furnace or liquation hearth, one lead-refining furnace, three zinc distillation retorts, one English cupellation furnace, supplied with blast by a No. 3 Sturtevant blower, which is run by a small steam-engine having a vertical tubular boiler, and an assay office, in which there are two wind-furnaces of the ordinary construction, and also a small muffle furnace. The assay office is supplied with all the necessary apparatus and reagents for fire assaying. There are also a superintendent's office, various store-rooms for coke and charcoal, and for the preparation of fire-clay, etc. Recently a small slag hearth (Krummofen) with one tuyere, has been put up for the purpose of working over such slags as assay too high in silver and lead to be thrown away, of which there are large amounts. The principal ore worked while I was in the employ of the company was that of the well known Emma mine in Utah, and also small quantities of Colorado ore. The character of the Emma ore is well known to most members of the Institute. In consists principally of ferruginous mixtures of carbonate and oxide of lead, oxide

Jan 1, 1874

By Julian M. Avery

In its dual role of pig-iron smelter and gas producer, the blast furnace is a remarkably satisfactory and efficient apparatus. Many metallurgists and engineers have pointed out, however, that since the primary function of the blast furnace is to produce pig iron at the lowest possible cost, its function as a gas producer should be subordinated to this primary purpose. During the past 10 years or more, improvements in blast-furnace technique and economy have, in fact, been directed primarily to increasing efficiency in the use of the reducing power of the gases produced by combustion of coke at the tuyeres, to reduce iron ore within the furnace. The net over-all result is a decrease in the fuel value of the top gas per unit of volume, and per ton of pig iron, which is evidently more than offset in value by the corollary saving in coke and the possibility of increased furnace capacity, for otherwise there would be no point in making such improvements. The purpose of the present paper is to suggest that, while progress has been made in this direction, there is another approach to the problem of increasing the chemical and thermal efficiency of the blast furnace in its primary role as a pig-iron smelter, which appears to offer possibilities of improvement in over-all ecorlomy of a different order of magnitude than results thus far obtained by the use of other expedients. The present argument is based in large part upon the hypothesis that the efficiency and economics of pig-iron smelting are seriously and adversely affected by the phenomenon known as "solution loss," and that the problem of solution loss call be successfully attacked by increasing the over-all pressure; i.e., the "top prcssure" under which the furnace is operated. It is indicated that pressure operation may also be expected to result in concomitant benefits, which may be summed up as generally improved operating conditions, together with a substantial saving in fuel and/or a substantial increase in furnace capacity. In a broad sense, the suggestion of pressure operation of the pig-iron blast furnace is not new, for operation under moderately increased over-all pressure was suggested as early as 1871, by no less an authority than

Jan 1, 1938

By Julian M. Avery

In its dual role of pig-iron smelter and gas producer, the blast furnace is a remarkably satisfactory and efficient apparatus. Many metallurgists and engineers have pointed out, however, that since the primary function of the blast furnace is to produce pig iron at the lowest possible cost, its function as a gas producer should be subordinated to this primary purpose. During the past 10 years or more, improvements in blast-furnace technique and economy have, in fact, been directed primarily to increasing efficiency in the use of the reducing power of the gases produced by combustion of coke at the tuyeres, to reduce iron ore within the furnace. The net over-all result is a decrease in the fuel value of the top gas per unit of volume, and per ton of pig iron, which is evidently more than offset in value by the corollary saving in coke and the possibility of increased furnace capacity, for otherwise there would be no point in making such improvements. The purpose of the present paper is to suggest that, while progress has been made in this direction, there is another approach to the problem of increasing the chemical and thermal efficiency of the blast furnace in its primary role as a pig-iron smelter, which appears to offer possibilities of improvement in over-all ecorlomy of a different order of magnitude than results thus far obtained by the use of other expedients. The present argument is based in large part upon the hypothesis that the efficiency and economics of pig-iron smelting are seriously and adversely affected by the phenomenon known as "solution loss," and that the problem of solution loss call be successfully attacked by increasing the over-all pressure; i.e., the "top prcssure" under which the furnace is operated. It is indicated that pressure operation may also be expected to result in concomitant benefits, which may be summed up as generally improved operating conditions, together with a substantial saving in fuel and/or a substantial increase in furnace capacity. In a broad sense, the suggestion of pressure operation of the pig-iron blast furnace is not new, for operation under moderately increased over-all pressure was suggested as early as 1871, by no less an authority than

Jan 1, 1938

By H. A. Baumann, A. J. Rostosky

EVER since the first installation of wet-washing methods of coal preparation, the removal of the water added by the washing process has created serious technical and operating problems. The rapid development and widespread adoption of wet washing has necessitated a corresponding development of dewatering methods and equipment. The amount of water retained by coal varies with the size of the coal. The moisture that is largely on the surface of the particles is easily shaken off coarse coal; thus coarse coal can be dried comparatively easily and quickly. Fine coal presents a larger surface area than does coarse coal, so its capacity for retaining moisture is greater. In fine coal, moisture below about 5 per cent is held between the coal particles and its removal is difficult. Draining and drying of the finer sizes is a major problem at many washeries. Two common problems of coal-washing practice that are intimately connected with dewatering and drying are the clarification of washery water and the prevention of stream pollution. The first field has been studied from many angles, including the use of coagulating and settling agents followed by vacuum filters to remove the solids, and the use of sludge tanks with dewatering screens incorporated therein. In many districts, the disposal of sludges into streams has been stopped by law. The lack of space for impounding sludges has created problems of disposal in other districts. Reduction in moisture means a saving in freight costs as well as the elimination of difficulties in unloading and storing. Excess moisture in coal causes it to freeze in localities where severe climatic conditions pre¬vail. Excess water in coals to be used in the production of coke and manufactured gas has a chilling effect on the walls of the oven or retort. Dryness of coal is important in producing good briquettes.

Jan 1, 1943

By C. E. Lesher

Coal has been fighting a rear-guard action since the last World War. The battle against competitive fuels has been largely guerilla warfare with more sniping within the ranks than of organized opposition. Oil and natural gas are the fuels that over these twenty odd years have driven coal backward and out of many profitable markets. Now, somewhat timidly, the coal industry is trying a new weapon; namely, Research, or let us more properly say, Organized Research. Engineers have been designing this weapon for many years, supported by those interested in coal, including some coal producers. A part of this pioneer work has been Fundamental Research, the Ph.D. kind that is over the heads of most of us. Another part has been aimed at immediate objectives and realizable profits, the practical, man-in-the-street sort. That is Industrial Research. Enough has been accomplished to make a fair exhibit, but whether this new weapon will have sufficient fire power to rout the opposition, whether the industry will really go into production and use it, the next few years will tell. Need foR Coal Research To utter "Research" is to use the modern magic word; to conjure up the miraculous—rubber from weeds; radar; magnesium from sea water; yes, even gasoline from coal. Research is a very general term. It means something different to every man. What is the coal industry seeking with its research; or what should it seek? And, specifically, how is it going about the job; and is it taking the best way? There are many who say that Coal has been asleep at the switch, while Oil and Gas have been taking the energy business. In an organized way this is true. Large-scale, privatelyfinanced research is just started in the Pennsylvania anthracite industry, and it is still a dream for bituminous coal. What has been done so far collectively is purely defensive; as, for instance, to improve mechanical devices for burning coal so as to be able to recover markets for house-heating fuel long since abandoned to oil and gas. To appreciate just how seriously bituminous coal has slipped back in the national economy in the past 2 5 years, one has only to recall that, in the last war the Navy required for its operations all the high-grade, low-volatile coal that could be produced, and that anthracite was withdrawn from the middle and northwest markets to keep the eastern seaboard warm. All coal was "rationed" by zones, if not to individuals. Now the Navy, the Armed forces and the Merchant Marine are propelled by oil and gasoline. Gasoline and heating oil are rationed to individuals. Production of all coal in this country in 1918 reached the historic figure of 678,200,-000 tons, and in 1943, after 25 years, it is expected to reach a special wartime total of 660,000,000 tons. Meanwhile, production of crude oil this year may exceed 1 ,500,000,000 bbl., and like that of natural gas, reach four times the amount produced in 1918.

Jan 1, 1944

By C. E. Lesher

Coal has been fighting a rear-guard action since the last World War. The battle against competitive fuels has been largely guerilla warfare with more sniping within the ranks than of organized opposition. Oil and natural gas are the fuels that over these twenty odd years have driven coal backward and out of many profitable markets. Now, somewhat timidly, the coal industry is trying a new weapon; namely, Research, or let us more properly say, Organized Research. Engineers have been designing this weapon for many years, supported by those interested in coal, including some coal producers. A part of this pioneer work has been Fundamental Research, the Ph.D. kind that is over the heads of most of us. Another part has been aimed at immediate objectives and realizable profits, the practical, man-in-the-street sort. That is Industrial Research. Enough has been accomplished to make a fair exhibit, but whether this new weapon will have sufficient fire power to rout the opposition, whether the industry will really go into production and use it, the next few years will tell. Need foR Coal Research To utter "Research" is to use the modern magic word; to conjure up the miraculous—rubber from weeds; radar; magnesium from sea water; yes, even gasoline from coal. Research is a very general term. It means something different to every man. What is the coal industry seeking with its research; or what should it seek? And, specifically, how is it going about the job; and is it taking the best way? There are many who say that Coal has been asleep at the switch, while Oil and Gas have been taking the energy business. In an organized way this is true. Large-scale, privatelyfinanced research is just started in the Pennsylvania anthracite industry, and it is still a dream for bituminous coal. What has been done so far collectively is purely defensive; as, for instance, to improve mechanical devices for burning coal so as to be able to recover markets for house-heating fuel long since abandoned to oil and gas. To appreciate just how seriously bituminous coal has slipped back in the national economy in the past 2 5 years, one has only to recall that, in the last war the Navy required for its operations all the high-grade, low-volatile coal that could be produced, and that anthracite was withdrawn from the middle and northwest markets to keep the eastern seaboard warm. All coal was "rationed" by zones, if not to individuals. Now the Navy, the Armed forces and the Merchant Marine are propelled by oil and gasoline. Gasoline and heating oil are rationed to individuals. Production of all coal in this country in 1918 reached the historic figure of 678,200,-000 tons, and in 1943, after 25 years, it is expected to reach a special wartime total of 660,000,000 tons. Meanwhile, production of crude oil this year may exceed 1 ,500,000,000 bbl., and like that of natural gas, reach four times the amount produced in 1918.

Jan 1, 1944

By L. D. Mullins, E. B. Elfrink, W. L. Wahl

In the past few years several articles and papers presenting results of solution gas-drive depletion calculations have appeared in the lit-erature. Such calculations are of interest to the oil industry, for investment decisions must often be made before much is known about a reservoir. At other times, an estimate of the possible benefits to be realized from alternate production methods is desirable, and theoretical depletion calculations can serve as a floor or reference level from which to work. In any case, an estimate of ultimate oil recovery based upon engineering data is commonly required. An engineer confronted with the problem of obtaining, for a specific reservoir system, an estimate of ultimate oil recovery by solution gas-drive depletion usually will be forced to perform the calculations himself. This is despite the quantity of data in the literature. Rarely will either experience or the literature provide results from a reservoir system similar in all important respects to the one under consideration, and calculated results are not so plentiful that satisfactory interpolation procedures can be devised. Performing the calculations, however, is a tedious, time-consuming task unless an electronic computer is available, and, in practice, time and manpower are not always available for this purpose. A quick, simple, consistent method was needed for reducing the uncer- tainty in estimated oil recovery from solution gas-drive reservoirs when only minimum information about the reservoir system is available. PROCEDURE Method of Calculation The usual requisite assumptions were made so that the material balance equation could be used to calculate data for the charts. The following assumptions were made: (1) the reservoir is homogeneous and isotropic; (2) oil recovery is due entirely to solution gas drive and neither a gas cap nor a water drive nor gravity drainage is present; (3) the initial reservoir pressure is the bubble-point pressure of the reservoir fluid; (4) initial total liquid saturation is 100 per cent of pore space; (5) interstitial water saturation remains at the initial value as the reservoir pressure declines from the bubble-point pressure to atmospheric pressure; (6) equilibrium gas saturation is 5 per cent of pore space; and (7) oil and gas saturations are uniformly distributed throughout the reservoir at all times. There are no saturation gradients due to a wellbore, nor is the geometry of the reservoir system considered. The material balance equation was written in the form of a differential equation' which was integrated to determine the change in oil saturation for an assigned pressure drop. Formal integration was not possible, so recourse was made to the Runge-Kutta method' of numerical integration. All computations were performed on IBM equipment. Numerical integration yielded the change in oil saturation within the reservoir as the pressure. declined from the bubble-point pressure to atmospheric pressure. The initial oil saturation minus the change in oil saturation yielded the oil saturation at atmospheric pressure. The oil originally in place was obtained by dividing the initial oil saturation by the initial formation volume factor (differential liberation) while the oil in place at atmospheric pressure was obtained by dividing the final oil saturation by the formation volume factor at atmospheric pressure. U1timate oil recovery, expressed as a percentage of the initial oil in place, was obtained by dividing the difference between the oil initially in place and the oil in place at atmospheric pressure by the oil initially in place and multiplying by 100. PVT Data Charts were based upon 135 solutions to the material balance equation. PVT properties of the reservoir fluids were variables in this equation and had to be known as functions of pressure. The required PVT data might have been obtained from either actual reservoir fluid systems or correlated data. However, correlated PVT data were developed and employed in the calculations for the following reasons: (1) it is doubtful that 135 sets of PVT data could have been obtained for the values of variables investigated in this study, and (2) results of recovery calculations from randomly obtained PVT data could not be correlated as well as rssults from selected PVT data. The PVT data used to develop the

George E. Collins, Nacoochee, Ga. (communication to the Secretary): The results tabulated below were obtained at the Reynolds mill, White county, Ga. They were noted, not with a view to investigating the point discussed by Mr. Clark, but in course of a test on a working scale to determine the com parative saving from a given free-milling ore on copper and silvered plates respectively. In every case the bullion assayed was the result of a separate clean-up on a considerable quantity of ore. The ore varied widely in grade and in other respects, but the runs bracketed in the table were made at the same time, in adjoining batteries, and on similar types of ore. In a * Result modified by the addition to the bullion-shipment of a little impure bullion left over from previous clean-ups.. On these occasions, the strips of copper were removed from the tables, and: their lower surfaces were cleaned. Hence the higher yield reported.

Jan 1, 1900

By Howard L. Hartman

There is reason to believe that ventilation systems so far devised for use with continuous mining machines fall far short of success. This is vividly demonstrated to anyone who has observed in a continuous miner section the localized ignitions of pockets of gas and the generation of dense clouds of dust by the cutting head of the machine. The alarming frequency with which major ignitions and disasters continue to occur in modern mechanical mining and the rise in incidence of pneumoconiosis serve as reminders that our ventilation systems are far from achieving the ultimate in providing protection from either short-term explosions or long- term dust diseases, both of which take lives. Human safety is the main concern in ventilation. But in this day of high-priced labor, let us not forget human comfort, either, for this is a major factor in motivation toward high productivity. The failure or inadequacy of most mine ventilation systems in providing the kind of working conditions at the face that are conducive to productive as well as safe operation is an indictment of our environ- mental control program in mining generally.

Jan 3, 1962

By Charles E. Parsons

One of the greatest factors in our industrial development is cheap and convenient power. Long-distance electrical transmission has now reached such a stage that it is feasible, and practicable, to utilize the water-power of the country which was heretofore too remote for consideration. In all of the changes of energy from its various sources to its electrical applications, water-power stands pre-eminent in point of economy. Power-users the world over have endeavored to utilize this force in preference to any other, and until long-distance transmission was found practicable it seemed that every available water-power in this section of the country was doing its full share for the benefit of mankind. The success of each great industrial development has been clue in a greater part to some one man one who is just a step in advance of the rest in his particular field; one who is able to grasp a situation and foresee possibilities; and, above all, one who has that indomitable pluck and perseverance which sees in each obstacle one more step toward success. Such a mail is Eugene L. Ashley, for it was through his efforts that the development of the greatest power on the Hudson river was made possible. For several years prior to 1897 the various properties along the river between Glens Falls and Palmer Falls were in the hands of speculators. These men knew the value of waterrights, but they had not the ability to assemble the properties and finance such an undertaking. In 1897 Mr. Ashley began buying these water-rights, and, after two years of litigation, title mas secured to all of the properties along each side of the river, and the Hudson River Water-Power Company was organized to construct a dam and transmit power to the surrounding cities and villages. A contract was let for a dam

Jan 1, 1904

By C. T. Liu, J. Gurland

The deformation behavior in tension of spheroidized carbon steels was studied at room temperature as a function of carbon content, 0.065 to 1.46 wt Pct, and carbide particle size, 0.88 to 2.77 p. It was found that the Hall-Petch strength-grain size relation is directly applicable to the yield and flow stresses of the two lower-carbon steels , 0.065 and 0.30 pct C. The strength data for the medium- and high-carbon steels, 0.55 to 1.46 pct C, also satisfied the Hall-Petch relation, provided that these data are based upon the particle spacing. Beyond 4 pct strain, the flow stress data of all the steels studied could be represented by the same Hall-Petch relation with dinerent spacings for grain boundary and particle strengthening. The behavior of the higher-carbon steels was consistent with the postulated formation of a dislocation cell network during processing and initial deformation (up to 4 pct strain). The cell size was assumed to be equal to the planar particle spacing. The true stress at the ultimate tensile strength was also found to be a function of the particle spacing. At a given temperature and strain rate, the yield and flow stresses of carbon steels depend on the type and dimensions of the microstructure. Starting with the work of Gensamer et al. in 1942,' experimental studies on pearlitic and spheroidized carbon steels revealed that the strength of steels is a function of two main parameters: the ferrite grain size2'3 and the carbide particle spacing;1'4'5 on this basis, two different strengthening mechanisms have been developed to apply to steels of low and high carbon contents, respectively. In polycrystalline iron and mild steels the grain boundaries are regarded as the major structural barriers to slip. The relation between strength and grain size is generally represented by the Hall-Petch equation which is based on a linear proportionality between strength and the inverse square root of the average grain size.2'3y677 However, Gensamer et al.' and Roberts et related the yield strength of medium -and high-carbon steels to the carbide particle spacing alone, and they found a linear relation between the logarithm of the mean free path in the ferrite and the yield strength in both spheroidized and pearlitic steels. By means of the electron microscope, Turkalo and LOW' extended the study to finer structures; they concluded that the logarithmic relation is not valid for the entire range of microstructures unless grain boundaries are also included in the measurement of the mean free path. For the specific case of spheroidized steels, Ansell and aenel' found that the yield strength data,4'5 when plotted as a function of mean free path, fit the Hall-Petch equation; however, T'ysong found that the same data fit the 0rowanl0 relation if a planar inter-particle spacing is used. Recently Kossowsky and ~rown" studied the strength of prestrained spheroidized steels, 0.48 and 0.95 pct C, and concluded that the strength due to the carbide dispersions varies linearly with the reciprocal of the square root of the mean free path between carbide particles and dislocation networks. Such networks were first observed by Turkalo." The conclusion common to all these studies is that the available slip distance in the ferrite is the most important variable in determining strendh. Previous work on carbon steels is restricted to limited composition and strain ranges. The mechanism which governs the flow properties is not clearly understood, and, in particular, little is known about the composition dependence of the transition between grain boundary strengthening and particle hardening. The purpose of the present work is to investigate the strengthening mechanism in spheroidized steels over a wide range of carbon content, 0.065 to 1.46 wt pct, and plastic strain, yielding to necking. The spheroidized structure was chosen because of its relative simplicity and the relative ease of control and measurement of the structural parameters. The experimental work is limited to tensile testing at room temperature at constant extension rate. The effects of the carbide particles on the fracture behavior of spheroidized steels are discussed elsewhere.13 EXPERIMENTAL PROCEDURE Eight different grades of vacuum-cast carbon steels were supplied in the form of forged and rolled plate by the Applied Research Laboratory of the U.S. Steel Corp. The compositions furnished with these steels are given in Table I; the carbon content ranges from 0.065 to 1.46 wt pct, or from 1.0 to 22.3 vol pct of carbide. The steel plates were cut transversely into rods a little larger than the test specimens, 1 in. gage length, i in. diam. The rods were austenitized in air (enriched with CO by a consumable carbon-rich muffle) at 50° C above theA, orA., temperature for 2 hr and then quenched in oil with vigorous stirring. The as-quenched rods were tempered in two stages in order to obtain the desired distributions and sizes of carbide particles. The rods were first tempered at 460° C for 10 hr and then at 700" C for periods ranging from 4 hr to 3 days, in vacuum. After final machining, all specimens were vacuum-annealed again at 650°C for 1 hr in order to relieve residual stresses. The tension tests were carried out in two steps. The initial part of the load-strain curve, up to about 2 pct strain, was determined on a Riehle testing machine with an extensometer of small strain range, 4 pct strain, in order to obtain the yield and initial flow piopertiesi As soon as the first part of the test was finished, the specimen was placed in an Instron testing machine equipped with a strain gage extensometer with a maximum strain range of 50 pct. The load-strain curve to fracture was

Jan 1, 1969

By V. R. Garfias

Although the work on which this paper is based was carried on by the writer as Special Commissioner of the Petroleum Department of the Mexican Government, the opinions expressed are only his personal views for which the Mexican Government can in no way be held responsible. Notwithstanding that the appointment covers all phases of the so-called petroleum question, as the one question of immediate importance was that relating to taxation, it was decided to devote all the time to this phase of the work. The present report has been divided into two closely related parts, the first dealing with the production and marine transportation of Mcxican petroleum, and the second, with the Mexican taxation on petroleum and its products. The writer wishes to acknowledge the loyal cooperation rendered by Mr. M. C. Ehlen, who had charge of the statistical work, and by Miss S. Stern and Messrs. E. P. Heiles and J. E. Morrissey. The aim throughout the work has been to pave the way for a thorough understanding between the Mexican Government and the oil operators and to present a true and clear statement of facts relating to the questions at issue. Mexican Oil Fields Development The salient features in the development of the Mexican oil fields may be summarized as follows: 1901. First commercially productive well in Ebano field. 1902. Tehuantepee field came in; Diaz Government granted concession to Pearson & Son on practically all Federal lands along the Gulf of Mexico. 1907. First producing well in the Furbero field. 1908. Dos Bocas well caught fire, advertising tremendous productivity of Southern oil fields of Mexico.

Jan 1, 1921

By John F. Knudsen

Following the flowsheet from the primary crushing plant of Ray mines division through the final products sample mill, there are eight exhaust systems ranging in size from 12,000 to 30,000 cfm. Where possible, hood face velocities are kept around 500 ft per min, permitting branch velocities of 2500 ft per min. Tight-fitting enclosures are provided over all ore drops, crushing operations, and vibrating screens. All enclosures are exhausted either primarily or secondarily, except those around conveyor head-pulleys where the ejector effect of the falling ore creates sufficient indraft to abate dust dissemination. IN 1947 an Industrial Hygiene Department was organized to represent and assist the four western mining divisions in industrial hygiene problems. Department headquarters are located at the Utah Copper Division, Magna Plant, Magna, Utah, with a branch office at the Chino Mines Division, Hurley, N. M. The headquarters staff includes a director, a department secretary, an industrial hygienist, a supervising ventilation engineer, and two ventilation designers. To be in closer association with work at the Southwest properties, a field engineer at the branch office conducts field studies which include ventilation problems at the New Mexico and Arizona properties;i.e., the Chino and Ray mines divisions. Functions of the department are to discover and evaluate existing hazards and to develop protective measures, either by personal protective devices or by proper ventilation, depending on the nature of the contaminant. Other than dust counting, all air samples collected at the four properties are processed at the home office. If through plant surveys or by suggestion of management some type of ventilation or air conditioning is required, the problem is usually handled by the ventilation section of the headquarters department, where general arrangement or line drawings are prepared, showing hoods, ducting, and equipment. Some hood and special parts detailing is done at headquarters; otherwise, required detailing is done by the respective plant engineering departments. Prior to the design of industrial ventilation, either new projects or the revamping of old ones, a thorough survey is made of existing conditions. In so far as possible weighted average exposures are determined and adequate ventilation provided on the basis of maximum allowable concentrations of the contaminant in question, as well as medical case histories, if these are available.

Jan 1, 1954

By Thomas R. Mager

An in.t!estigation has been made of the equilibrium conditions at 1200°C in the reaction between hydrogen sulfide gas and sulfur dissolved in Fe-Si alloys From this the equilibrium constant, activity coefficient, and activity of sulfur in solution were calculated. A number of studies of the equilibrium of sulfur with iron and iron alloys have given closely agreeing results from which the activity and free energy of the dissolved sulfur may be found. Sherman, El-vander, and chipman1 discussed the significant researches of dilute solutions of sulfur in liquid iron prior to 1950, and the results of this study indicated that the relationship between the ratio of PH2S/PH2 in the environment and the percentage of sulfur in solution is not a linear one. Morris and williams2 studied the equilibrium conditions in the reaction between hydrogen sulfide gas and sulfur dissolved in liquid iron and Fe-Si alloys, and reported that silicon dissolved in iron has a pronounced effect on the equilibrium conditions. They found that the activity of sulfur in iron is increased by the addition of silicon. At a silicon content of 4 pet the activity coefficient of sulfur was about twice that for sulfur dissolved in pure iron. Sherman and chipman3 investigated the chemical behavior of sulfur in liquid iron at 1600°C through the study of the equilibrium: H2 + S = H2S; K = PH2S/PH2 . 1/as [1] From the known equilibrium constant of the reaction between H2, H2S, and S and the experimental data, the activity of sulfur in the melt was determined. They found that the activity coefficient of sulfur defined as fs = as/%s is increased by silicon and decreased by manganese. Morris4 and Turkdogan5 also reported that manganese decreases the activity coefficient of sulfur in liquid iron and iron-base alloys. A recent technique of sulfur analysis developed by Kriege and wolfe6 of the Westinghouse Research Laboratories permits an accurate sulfur analysis of 0.5 * 0.2 ppm in the range of 0.1 to 3 ppm, whereas in the range of 3 to 50 ppm the accuracy is ±1 ppm. This technique of sulfur analysis was utilized in this experiment. Previous unpublished data reported that sulfur analysis by the combustion technique was not accurate below 20 ppm. EXPERIMENTAL PROCEDURE Five 5-lb ingots of high-purity Fe-Si were prepared. Three of these ingots were prepared without the addition of manganese but with a variation of silicon contents from 2 to 4 pet. The remaining two ingots contained 3 pet Si with the addition of manganese. Ingots were made at each of three silicon levels: 2, 3, and 4 pet. No alloys were made with less than 2 pet Si since below approximately 1.8 pet Si the binary alloy exhibits a to ? transformation. The two additional ingots of 3 pet Si-Fe were made at each of two manganese levels: 0.20 and 0.50 pet. To minimize the effects, if any, of impurities on the activity of sulfur on Si-Fe, the best metals available were used for melting. All ingots were vacuum-melted in magnesium oxide crucibles. After obtaining samples for chemical analyses, the ingots were processed. This consisted of hot rolling and subsequently cold rolling the alloys. Each ingot was hot-rolled at 1000°C, reheating between every pass to minimize grain growth. All heating was done in a protective argon atmosphere. The slabs were hot-rolled to strips 50 mils thick. After hot rolling, all the material was pickled to remove the scale formed on the surface of the strip during hot rolling. The material was then cold-rolled to 12-mil strips. Single strips of the material used in this experiment were hydrogen-annealed at 1200°C for 16 hr in an alumina tube. Chemical analyses of strips M-1, M-3, M-4, M-7, and M-8 are given in Table I. Sulfur, silicon, and manganese analyses were made from the millings from the cold-rolled 12-mil strips. The oxygen analyses were made from slugs of the as-cast material. The hydrogen sulfide used in these experiments was supplied from cylinders containing a mixture of argon and 1 pet hydrogen sulfide. The parts per million of hydrogen sulfide were determined from the analysis of the exit gas of the annealing furnace during each anneal. The flow rate of hydrogen was approximately 1 liter per min in all anneals. The

Jan 1, 1964

By Edward B. Walker, Michel Grosmangin

The geological and economic conditions peculiar to the Greater Oficina area are presented to demonstrate the necessity of a low-cost, well-site method of distinguishing gas-bearing formations. The method of gas detection with the neutron log is briefly discussed and its limitations are explained. A new method is described which consists in running a second neutron log with a larger source-to-detector spacing. Field data indicate that under favorable conditions the larger spacing response is proportionately more influenced by the virgin gas zone than is the shorter spacing response. One important condition is that the gas sands be invaded, with a diameter of invasion equal to about two to three times the hole diameter. The calibration of the longer spacing log is made so that the two logs read the same deflection in shale and in a known water or oil sand. Under such conditions, gas is indicated by a positive separation, i.e., the curve for the longer device is displaced to the right of the curve for the shorter device. Because of the non-linearity of the long spacing response, low porosity formations also show positive separations. In sands with large porosity variations, the gas sands can no longer he located visually. They can be detected on a plot of shorter spacing vs longer spac-ing deflections. INTRODUCTION In the Greater Oficina area of Eastern Venezuela, the rapid and accurate detection of gas from well logs is of primary importance because of a combination of economic, geologic, and operational conditions. Briefly, these conditions are: economic—there is no market for gas at the present time; geologic—a single well may contain as many as 30 or more oil or gas sands for which intervals -to be tested must be selected; opera-tional—first, once opened to the casing through perforations, gas sands are extremely difficult and expensive to squeeze off, and second, gas detection must be rapid because the geologist must decide immediately, at the well, which sand to perforate. During the early period of exploitation in Greater Ofi-cina, when clay base muds were used, sidewall samples, together with electric logs, gave fairly good distinction between oil and gas sands. When exploitation became concentrated on deep fields of poorer sidewall sample recovery, and after the advent of oil emulsion muds, now the standard drilling fluid in Greater Oficina, the regular neutron log became the most reliable indicator of gas. In 1953, R. Norelius devised the dual-spacing neutron technique for gas detection. The dual-spacing neutron log has proved to be highly successful in detecting gas and has been adopted as a regular survey by all of the oil companies of the area. Several hundred dual-spacing neutron logs have been run in Eastern Venezuela and several tests per well are available for positive evaluation of the logs. The findings outlined below are based upon this extensive field experience. GEOLOGICAL CONDITIONS OF THE GREATER OFICINA AREA The Greater Oficina area lies on the south flank of the Eastern Venezuela Basin (Fig. 1). Nearly all accumulations of oil and gas in the area are trapped, in whole or in part, against normal faults. All known oil and gas reservoirs in Greater Oficina occur in the Ofi-cina formation (Miocene-Oligocene) or in the "U" sands. The U sands are the lithologic equivalent of the Merecure group (Otigocene-Eocene), which contains oil in many fields north of Greater Oficina. Most of the petroleum produced in Eastern Venezuela is from the Oficina formation.

Jan 1, 1958