Search Documents

By G. S. Rice

With so tremendous a subject, an attempted review of the coal situation of the world in a short talk must necessarily be of a sketchy character. It is hardly necessary to tell a body of engineers that had it not been for nature's gift of coal the material side of modern civilization would never have reached its present status. On the other side, it is regrettable that it was a byproduct of coal, T. N. T., which made possible Germany's initial success in this war, because that country had an enormous development of manufacturing plants that could be immediately utilized to make this destructive agent: One sometimes hears the casual remark that when the coal of the world is exhausted we shall use electricity; but, of course, electricity is ordinarily only a means of transforming and transmitting energy derived from fuel or water power, and chiefly from coal. It is true, we have much undeveloped water power, but it is more or less remote from 'the, centers of industry; and when all shall have been developed it will not begin to supply the power requirements of the world. It is, however, reasonable to expect that before the world's supply of coal shall be exhausted, methods will have been discovered of harnessing other forces of nature, such as the tides, or the energy emanating from the sun. Petroleum and natural gas naturally come to mind, but the days of both, as fuel, appear to be numbered, although the products of petroleum, if economically used, doubtless will be available for internal-combustion engines, automobiles, trucks, and boats for a long time, provided the reckless use of crude petroleum as an ordinary fuel is stopped. The products of petroleum are too valuable to mankind for such waste to be permitted. The civilization of the world, therefore, appears to rest, and, so far as can be seen, will indefinitely continue to rest, upon coal. COal Resources of the World According to the compilation made by the geologists of the principal countries for the 12th International Geologic Congress, held in Canada

Jan 1, 1918

By C. S. Westerberg, C. P. Heiner

Observation of the clinkering action of coal from the Castle Gate D seam in underfeed stokers over a period of years has given rise to the present investigation of the effect of bony coal on clinkering. Some very costly examples of slagging clinkers in particular cases have been of especial interest to the authors. In such cases coal analyses and ash-softening and fluid temperatures have been found of little value. In general, it was noted that slagging mas accompanied by a somewhat higher ash content of the stoker slack, and the suspicion naturally arose that foreign matter was the troublemaker. One would naturally suspect bony coal and rock impurities because of their occurrence and prevalence within the seam and the relative absence of sulphur or other impurities in the coal mined. The test results given herein indicate that the concentration of the bony coal and rock impurities in the coal determines the clinkering tendencies of the ash during combustion. Castle Gate D Seam Extending from the Utah-Colorado line near Grand Junction, Colo., westward to Greenriver, Utah, and thence in semicircular form north and westward to Castle Gate, and from there southward to Mt. Hilgard in central Utah, is a line of nearly perpendicular cliffs, composed of interbedded massive sandstone and shales, making up the coal-bearing horizon of the Mesaverde formation of Upper Cretaceous age. The cliffs face roughly concentrically toward the south and southeast and the strata, with conformably enclosed coal beds, gently dip away from the face of the cliffs and at right angles to their front line. Back of these cliffs the mountain masses rise to an altitude of from 8000 to 10,ooo ft. above sea level. Stretching away from their foot is a great shale plain, on which the towns are situated and over which the railroad lines and highways run. The Castle Gate mines enter the coal beds at their outcrop; the workings extending within a particular coal bed away from the outcrop and under the mountain mass back from the cliff line (Fig. I). Throughout the Mesaverde formation in the Castle Gate general area, there are from two to five workable coal beds. Usually not all of these are coincidentally of workable size and merchantable quality throughout any given large tract. In the Castle Gate mine area, the base of the Mesaverde horizon and coal measures is marked by a massive, cliffmaking, gray sandstone bed 60 to 80 ft. thick. Locally this is referred to as the "Castle Gate sandstone floor." Frank R. Clark, in U. S. Geol. Survey Bull. 793, designates it as the "Aberdeen sandstone." At Castle Gate the various coal beds are designated by the letters A, B, C, etc., commencing with the lowest bed.

Jan 1, 1942

By C. P. Heiner, C. S. Westerberg

Observation of the clinkering action of coal from the Castle Gate D seam in underfeed stokers over a period of years has given rise to the present investigation of the effect of bony coal on clinkering. Some very costly examples of slagging clinkers in particular cases have been of especial interest to the authors. In such cases coal analyses and ash-softening and fluid temperatures have been found of little value. In general, it was noted that slagging mas accompanied by a somewhat higher ash content of the stoker slack, and the suspicion naturally arose that foreign matter was the troublemaker. One would naturally suspect bony coal and rock impurities because of their occurrence and prevalence within the seam and the relative absence of sulphur or other impurities in the coal mined. The test results given herein indicate that the concentration of the bony coal and rock impurities in the coal determines the clinkering tendencies of the ash during combustion. Castle Gate D Seam Extending from the Utah-Colorado line near Grand Junction, Colo., westward to Greenriver, Utah, and thence in semicircular form north and westward to Castle Gate, and from there southward to Mt. Hilgard in central Utah, is a line of nearly perpendicular cliffs, composed of interbedded massive sandstone and shales, making up the coal-bearing horizon of the Mesaverde formation of Upper Cretaceous age. The cliffs face roughly concentrically toward the south and southeast and the strata, with conformably enclosed coal beds, gently dip away from the face of the cliffs and at right angles to their front line. Back of these cliffs the mountain masses rise to an altitude of from 8000 to 10,ooo ft. above sea level. Stretching away from their foot is a great shale plain, on which the towns are situated and over which the railroad lines and highways run. The Castle Gate mines enter the coal beds at their outcrop; the workings extending within a particular coal bed away from the outcrop and under the mountain mass back from the cliff line (Fig. I). Throughout the Mesaverde formation in the Castle Gate general area, there are from two to five workable coal beds. Usually not all of these are coincidentally of workable size and merchantable quality throughout any given large tract. In the Castle Gate mine area, the base of the Mesaverde horizon and coal measures is marked by a massive, cliffmaking, gray sandstone bed 60 to 80 ft. thick. Locally this is referred to as the "Castle Gate sandstone floor." Frank R. Clark, in U. S. Geol. Survey Bull. 793, designates it as the "Aberdeen sandstone." At Castle Gate the various coal beds are designated by the letters A, B, C, etc., commencing with the lowest bed.

Jan 1, 1942

By W. L. Saunders

It has been estimated that the value of the mineral products of the United States is about $2,000,000,000 a year; that about $25,000,000 is expended annually for explosives and that about double this sum is paid in wages where blasting is done. The value of the mineral products does not adequately express the importance of the industry involved in the excavation of rock and ore because of the enormous sums of money expended in tunnel driving, in quarries, and in open-cut excavation generally. We know that the Catskill Aqueduct in the neighborhood of New York, which is now nearing completion, has cost some $165,000,000 and that about one-third of this may be rated as rock excavation. These illustrations are given in order to call attention to the great importance of an industry the extension and development of which in our industrial life depend so much upon the economics of rock drilling. Reference has been made to the new Catskill Aqueduct. There are three aqueducts leading into New York, each built at periods separated by some 20 years of time. The first one, known as the Old Aqueduct, conveys the waters of the Croton river to New York City in a manner which reminds one of the old Roman aqueducts, the ruins of which are still in evidence. The engineers who laid out these old conduits sought to direct their lines around the hills and into the valleys, at all times avoiding the rock. When it was necessary to cross a river or a deep ravine, a bridge or causeway was constructed. High Bridge, over the Harlem river, is an arched masonry viaduct differing in no essential features from the aqueducts of the Romans. When the second Croton Aqueduct was built, about the year 1890, the art of drilling rock had been so far perfected, and the use of explosives, through the invention of dynamite, had become so general, that this waterway was planned and executed on straight lines, following rather than avoiding the rock. The second Croton Aqueduct is a tunnel through rock, about 32 miles in length; material gneiss, almost as hard as granite. Its construction was made practicable by sinking

Jan 1, 1914

We did install one 100% brick bottom in our #33 furnace which is basically the same design as Inland's furnace. We had previously embarked on a program of replacing all bottoms in our 300 ton furnaces every 2nd campaign which would be about every 2000 - 2300 heats. This had been necessitated by the effect of our rather high oxygen blowing rates and our desire to maintain a minimum bottom interval level. This meant that we were able to compare bottom performance of various types of materials on a realistic bas is. Since furnace availability is critical to our operation, we are organized to employ every piece of equipment and all the necessary man power to complete a rebuild in the shortest possible time. A 300 ton furnace requires 7.5 days to rebuild. If a new bottom is to be installed an additional 2.5 days is added - 24 hours for tear out and 36 hours for bricklaying - making a total of 10 days.

Jan 1, 1972

By Charles T. Holland, David A. Olsen

Considerable work has resulted in the development of a formula by which the strength of coal pillars for an L to T ratio of up to 12 may be estimated. One of the factors involved in this formula is the coefficient of friction between the coal pillar and the adjacent rock with which it is in contact. This paper presents the results of studies on sandstone, limestone, shale and coal and the coefficient of friction between coal and the other three under wet and dry conditions. With the coefficients of friction thus determined and the use of results obtained earlier by Meikle and Holland, it seems probable that coal pillar strength may be more closely estimated. Several investigators1-3 have found that the com-pressive strength of cubical coal specimens can be correlated by an equation such as

Jan 1, 1969

By M. M. Wong, D. E. Couch, G. M. Martinez

The Bureau of Mines electrowon hafnium metal with an average oxygen content of' 150 ppm at 700°C from an electrolyte containing 27 wt pct LiCl, 62 wt pct RbCl, and 11 wt pct HfC14. The average anode and cathode current efficiencies were 90 pct at anode and initial cathode current densities of 86 amp per sq ft. Haf-nium metal with an average oxygen content of 440 ppm was electrowon at 800oC from an electrolyte containing 90 wt pct KC1 and 10 wt pct HfCl4. The average anode and cathode current efficiencies were similar to those obtained in the LiCL-RbCl-HfCl, electrolyte. The chlorine gas given off at the graphite anode was vented through either a silica or a graphite tube to prevent cell corrosion. THE current method for the commercial production of high-purity hafnium is the thermal decomposition of Hfl4.1 The iodide method is not adaptable to continuous process techniques. Nettle, Hiegel, and Baker2 studied the electrorefining of hafnium from hafnium sponge containing 800 ppm oxygen. They failed to obtain hafnium with 600 ppm oxygen in their initial deposits and obtained AEC specification for oxygen only after 75 pct of the soluble hafnium had been removed from the electrolyte. Calculations using their data indicated this was approximately 4 lb of hafnium. The electrolyte was then used to produce approximately 3 lb of hafnium with a low oxygen content. However, no data are shown concerning the amount of anode material initially used or what percent of it was dissolved, therefore, results are not suitable for evaluation of a continuous operation. In general, it was not possible to consistently obtain low oxygen content metal with the electrolytes described by Nettle, Hiegel, and Baker. Wong, Hiegel, and Martinez3 investigated the electrorefining process for hafnium and showed that even by strict control of electrolyte composition only relatively low oxygen reduction could be obtained. The oxygen contained in the hafnium anode material tended to transfer to the cathode deposit and only a limited purification was possible. Both the "iodide" and the "electrorefining" processes depend upon hafnium sponge as a starting material. The sponge is normally produced by magnesium reduction of HfC14 ' and does not meet AEC specifications for hafnium metal. Since only 30 pct of the anode feed could be utilized3 in the electrorefining cells, the Bureau of Mines developed an electrowinning process. HfC14 was used as the feed material for the electro-winning process described in this report. Many of the electrolytes used in the electrorefining studies3 ap- peared to be suitable carrier-electrolytes for HfC14. However, in the initial studies on electrowinning, it was desirable to use electrolytes that had low solidus temperatures and could be operated over a wide temperature range to investigate parameters of the process. Therefore, electrolytes containing LiC1, NaC1, KC1, RbC1, CsC1, and HfC14, in various combinations were explored. EQUIPMENT Chlorinator. Hafnium carbide was chlorinated to produce HfC14 in the batch-type chlorination shown in Fig. 1. Chlorination temperatures were measured with a thermocouple placed in the center of the HfC charge. A flow meter was used to monitor the helium and chlorine. The exhaust side of the silica chlorina-tor tube was equipped with a flask for collecting organic material released during the initial heating of the HfC. The temperature of an internal heater, which extended from the HfC14 condensing flask to the hot end of the chlorinator, was adjusted to prevent the HfC14 from condensing before entering the collection flask. Helium and excess chlorine were exhausted through the lid of the collection flask to an aqueous NaOH solution. Sublimer. Initial studies were conducted using a sublimer, Fig. 2, made by placing a 13/8-in. OD nickel thimble 11 in. long, inside a 11/2-in. ID nickel bell 12 in. long, and locking it in place. This unit was loaded with HfC14 and partially immersed in the molten electrolyte for sublimation directly into the electrolyte. In another sublimer shown in Fig. 3, the HfC14 was contained in a "resin reaction flask". Quartz wool, previously heated to 600aC, secured between two nickel wire screens, was placed just above the HfC14 powder. The lid contained a vacuum outlet, a gage, an argon inlet, and an air-cooled pipe for condensing the HfC14. This sublimer was evacuated and heated. The sublimation temperature was not critical and the sublimer operated satisfactorily at all temperatures between 250" and 350°C. Electrolytic Cell. The electrolyte chamber, Fig. 4, was made of mild steel 8-in. schedule 20 pipe, 30 in. long. The exterior was metallized with a Ni-Cr alloy. The electrolytes were contained in a 16 gage nickel or iron liner with a nickel heat shield on top. The cell was heated by a resistance furnace. A 21/2-in. ID by 25 in. long air lock was connected to one port of a two-port cell cover assembly through a slide valve. The cover assembly of the air lock was electrically insulated from the cell and was equipped with a rubber sleeve that provided for the passage of the cathode lead. This allowed the cathode deposits to be removed and a new nickel cathode to be introduced without allowing air to enter the cell. A tube-rod assembly was bolted to the other port on the cell cover assembly and was sealed by a packing seal. The tube-rod assembly consists of a graphite

Jan 1, 1970

By E. P. Polushkin

This work has for its purpose the establishment of a new method for determining the structural composition of alloys. The area occupied by a constituent on a few representative photomicrographs of the alloy is measured, by a planimeter, especially designed for metallographic work, and the volume and proportional weight of the constituent calculated. Experiments have shown that the results are accurate enough to justify the application of the method to many problems in metallographic research instead of chemical analysis. The advantage of the method is the possibility of determining the amount of the constituents without separating them from the alloy; their composition may also be determined if the ultimate chemical analysis of the alloy is known. Suppose Fig. 1 represents a part of a photomicrograph on which the total area of the black figures is to be found. By a system of parallel lines drawn short equal distances apart all figures may be divided into trapezoids. As the area of a trapezoid is equal to its median multiplied by its altitude, the relation between the total areas of the black and the white figures comprised within each strip is equal to the relation between the sums of medians for these figures respectively. This is also true for the whole area of the photomicrograph. Therefore, to determine the total areas of the black and white figures we must first find the proportion between the sums of the medians and then divide the area of the whole photomicrograph in the same proportion.

Jan 1, 1925

By M. R. Geer, J. D. Davis, H. F. Yancey

ALTHOUGH the mechanical cleaning of coal is carried out at plants on the surface, preparation is actually begun at the face in the mine. Here the character of the coal and the amount, character, and distribution of the impurities within the bed may be seen. Blasting methods, dust-allaying procedures, location of mining cut with respect to bands of impurity, and the practice of discarding segregated impurities underground, all have an important bearing on the successful operation of surface cleaning units. The most important single characteristic of both coal and its asso¬ciated impurities from the standpoint of cleaning is specific gravity. Other characteristics related in one way or another to the preparation of coal are rank, petrographic composition, structure and hardness, and friability. These and still other coal properties are discussed in the first section of this chapter and impurity characteristics in the second. COAL CHARACTERISTICS RELATED TO PREPARATION Rank As a result of work done over a period of several years by committees of the American Society for Testing Materials and the American Standards Association, standard specifications are now available showing the classification of coals according to rank and quality of grade.' The term "rank" expresses the degree to which the original coal-forming material has been changed by metamorphism through successive stages from peat to anthracite. Table 1 shows the classification of coals according to rank as devised by the committees of the organizations mentioned. The basic scheme of classification for the higher-rank coals is according to

Jan 1, 1943

By William C. Sleppy

The nmgnetic susceptibility of heat-treatable aluminuin alloys is sensitive to chanyes such as solution or dissolution of solute and the precipitation of mew phases. By measuring the change in the magnetic susceptibility of aluminum alloys caused by various heat treatments, an empirical relation was found from which atomic arrangements in dilute binary alloys of copper, zinc, and magnesiutn in aluminum have been delineated. The relation predicts the ultimate formation of C1LA12 when copper is precipitated from solid solution in aluminum. Euidexce joy silovt- range order is found for copper in solid solution in aluminum in the sense that copper atoms avoid being nearest neighbors to an extent greater than would result from a purely random arrangertzeizt. Hume-Rothery has predicted such short-range order joy solid solution of copper in aluminum The Al-Zn system agrees with evidence obtained from X-ray scattering at small angles and predicts a tendency for zinc atoms to cluster in solid solution in aluminum. In the Al-mg system, the empirical relation indicates an approach to randor distribution of magnesium in solid solution in aluminum with a tendency for magnesium segvegation which increases with incveasing temperature. ThE magnetic properties of metals are complicated by the fact that contributions are made to them both by electrons of a "metallic" type which belong to the crystal as a whole, and by electrons in states localized on particular atoms. An expression1'2 for the bulk magnetic susceptibility of aluminum may be written as the sum of three contributions: where XA1 is the bulk susceptibility of aluminum per gram of material (in the cgs system, the units are those of reciprocal density); Xa1+3 is the diamagnetic contribution of the electrons localized in ion cores; Xa1 is. the paramagnetic spin contribution of conduction electrons often called Pauli paramag-netism: Xa1 is the diamagnetic contribution of the conduction electrons often called Landau diamag-netism. Ion core diamagnetism arises from the precession of the electron orbits which occurs when a magnetic field is applied to a system of electrons moving about a nucleus. Its contribution to the magnetic suscepti- bility is small, temperature-independent, and unaffected by alloying. The conduction electron diamagnetism is also temperature-independent and arises from the translatory motion of the electrons. For perfectly free electrons this contribution should be exactly one-third of the Pauli spin paramagnetism, but this relation is seldom even approximately true. Blythe2 determined the conduction electron diamagnetism in pure aluminum and found it to be extremely small. Any change in the conduction electron diamagnetism caused by alloying is neglected in this work. The Pauli paramagnetic contribution3 to the magnetic susceptibility of aluminum depends upon the number of electrons that occupy excited states and whose spins can be turned parallel to an applied magnetic field. The number of electrons free to turn in the field is proportional to the temperature and each spin contribution to the susceptibility is inversely proportional to the temperature. A slight temperature dependence of Pauli paramagnetism occurs when the number of electrons occupying excited states cannot increase sufficiently to balance the inverse dependence on temperature of each spin contribution. The decrease of the magnetic susceptibility of aluminum with increasing temperature is attributed to a temperature dependence of the Pauli paramagnetism. Estimates of the Pauli paramagnetism of aluminum have been made by several workers.2,4,5 All of the values are in reasonably good agreement with each other. In this work Xal at 17°C is taken as 0.761 X 10-8 cu cm per g. An expression similar to [I] can be written for the magnetic susceptibility of an aluminum base alloy containing a fractional weight percent x of solute:' Xa = (1 -x)XAl+3 +xXsoluteion * XaPauli +Xadia) [2] where X, is the magnetic susceptibility per gram of alloy, Xal'3and Xsolute ion are the ion core diamag-netic contributions, and xpauli and xdia are the Pauli and diamagnetic contributions of conduction electrons in the alloy. If the components of a mixture are not alloyed but simply mixed together in their pure states without producing a new phase, then the magnetic susceptibility of the mixture is given by the Wiedemann additivity law: Xm =x1X1 +x2x2 + ..xnxp [3] where X, is the susceptibility per gram of mixture and xnXp are the weight fractions and susceptibilities, respectively,-. for the pure components. The additivity law is not applicable to alloys because the outer electronic structures of the components are changed by alloying.' Both the Pauli paramagnetism and Landau diamagnetism are affected; hence the magnetic susceptibilitv of an alloy is usually different from that calculated using the additivity law. In this work the difference, X, -X,, is taken as a measure of the change caused by alloying.

Jan 1, 1968

By T. Y. Yan

SUMMARY Laboratory high pressure column tests have shown that the presence of 1-20 ppm of aluminum ion effectively prevents permeability loss during uranium leaching with leachates containing sodium carbonate. If added after permeability loss has occurred, aluminum ion can restore the permeability to nearly its original value. No deleterious effect was observed on uranium leaching performance and the technique should be quite compatible with all field operations. INTRODUCTION The recovery of uranium values from underground deposits by in situ leaching or solution mining has become economically viable and competitive with conventional open pit or underground mining/milling systems (Merrit, 1971). In situ leaching processes are particularly suitable for small, low-grade deposits located in deep formations and dispersed in many thin layers. Many such ore bodies occur along a broad band of the Gulf Coastal Plain (Eargle et. al., 1971). The advantages of the in situ leaching processes have been reviewed (Anderson and Ritchi, 1968). In the in situ leaching process, a lixiviant containing the leaching chemicals is injected into the subterranean deposit and solubilizes uranium as it traverses the ore body. The pregnant lixiviant or leachate is produced from the production well and is then treated to recover the uranium. The resulting barren solution is made up with the leaching chemical to form lixiviant for re-injection. Upon completion of the leaching operation, the formation is contaminated with leaching chemicals and other species made soluble in the leaching operation and has to be treated to reduce the concentration of these contaminants in the ground water to levels acceptable to the regulatory agencies (Witlington and Taylor, 1978). Restoration is accomplished by injecting a restoration fluid, which could be the fresh water or water containing chemicals, into the formation. As it traverses the leached formation, the restoration fluid picks up the contaminants and is then produced at the production well. This produced water is either disposed or purified for recycle. In both phases of operation, formation permeability or well injectivity is one of the most important parameters which determines the viability of the in situ leaching process. Low formation permeability limits production rates, leading to uneconomical operations. The formation is said to be sensitive if there is a sharp loss of permeability on contact with water and other fluids. Many uranium bearing formations, for example, the Catahoula formation of the Texas Coastal Plain, contain significant amounts of clay minerals which are water sensitive. Serious permeability losses can occur when the pH and chemical composition of the lixiviant is significantly different from that of the formation water. Jones has investigated the influence of chemical composition of water on clay blocking of permeability (Jones, 1964) and Mungan studied permeability reduction through changes in pH and salinity of the water (Mungan, 1965). Various mechanisms of permeability damage have been proposed and reviewed (Jones, 1964; Mungan, 1965; Gray and Rex, 1966; and Veley, 1969). When large amounts of swelling clays are present, a significant fraction of the flow channels in the formation can be reduced due to swelling. However, in most cases, swelling need not be the main cause of permeability losses. Particle dispersion and migration or clay sliming can be more important causes for formation damage. Clay particles entrained in the moving fluids are carried downstream until they lodge in pore constrictions. As a result, microscopic filter cakes are formed by these obstructions, plugging the pores, effectively restricting fluid flow and reducing the formation permeability. Moore found that as little as 1-4 percent clays present in a fine grained sandstone could completely plug the formation if they are contacted by incompatible injected fluids (Moore, 1960). It has been found that injection of NaHC03/Na2CO3 lixiviant into formations with significant clay content often leads to loss of formation permeability and well injectivity. To alleviate this problem a change of the lixiviant composition to KHC03/K2CO3 has been proposed. At present, however, many in situ leaching operations employ NH4HC03/(NH4)2C03 mixtures as a source of carbonates. This approach has been successfully used in South Texas by Mobil, Intercontinental Energy, Wyoming Minerals and U.S. Steel, etc. The use of ammonium carbonates solutions, however, contaminates the formation and requires a time-consuming restoration operation. The other approach to reduce the permeability loss is to pretreat the sensitive formation with chemicals which prevent clay dispersion and migration. Such chemicals include hydroxy-aluminum (Reed, 1972 and Coppel et. al., 1973), hydrolyzable zirconium salts (Peters and Stout, 1977), hydrolyzable metal ions in general (Veley, 1969) and polyelectrolyte polymers (Anonymous). Still another approach, is to minimize the "shock" caused by sudden injection by gradually changing the chemical composition of the injected fluids from that of the formation water. THE APPROACH Since permeability loss can be an important factor limiting the efficiency and economic viability of the in situ leaching process, a study was initiated on

Jan 1, 1982

By G. L. Craig

COPPER containing a small amount of arsenic has been used extensively abroad, and a number of reports, particularly those by English workers, have indicated that such copper is better suited for certain uses than high-conductivity copper. Inasmuch as a large percentage of the copper fabricated is used for nonelectrical purposes where high conductivity is not at all essential, it has been suggested that arsenical copper might be at least as suitable as high-conductivity copper for many purposes. An investigation spon-sored by the Calumet & Hecla Consolidated Copper Co. at Battelle Memorial Institute was therefore undertaken with the object of determin-ing the effect of small amounts of arsenic (up to 0.75 per cent) on the properties of copper. In this work the effect of arsenic on the basic properties of tough-pitch and of phosphorized copper have been critically studied and many data collected from laboratory experiments which have been supplemented by mill-scale tests. The results of these tests, with coppers of the type referred to, in the annealed condition and after various degrees of reduction, show that the basic properties of copper are not greatly affected by small amounts of arsenic, an increase in strength being observed with increasing arsenic with no corresponding decrease in ductility. It is well known that the evaluation of material for plastic deforma-tion, on the basis of laboratory tests, may not be directly comparable with its performance in commercial operations. In order, therefore, to substantiate the data obtained at the Institute, the cooperation of the Wolverine Tube Co. was obtained for a series of production tests on the fabrication characteristics of phosphorized arsenical copper in the manu-facture of seamless copper tubing. In these tests the behavior of the arsenical coppers was carefully observed in comparison with that of representative types of phosphorized arsenic-free copper, which were fabricated under the same conditions.

Jan 1, 1933

By E. A. Holbrook

The art of ore dressing is as old as civilization itself. Jason's search for the golden fleece was perhaps only the use of sheepskins for catching gold from gold-bearing sands washed over them. From Hoover's translation of Agricola we gather that in the middle ages ore dressing had advanced through the stage of hand sorting to water concentration by jigging. German methods and apparatus continued in the lead until the closing years of the past century; indeed, it is little more than a generation ago that many ore-dressing plants in this country were designed and operated by German-trained ore-dressing specialists. Meanwhile the development of the ore deposits in this country during the nineteenth century brought forth new inventions and methods. Blake's invention of the rock breaker in 1858 and the coming of the Wilfley table about 1896 are random examples of the improvements caused by our expanding needs. Yet ore dressing remained an art developed and practiced more or less by cut and try methods. The publication of the volumes on Ore Dressing by Dr. Robert H. Richards in 1903 marks the beginning of American ore-dressing practice as a science. Previously we had as guides only a few incomplete books based on foreign practice, or scattered references and articles in our own Transactions. Dr. Richards set down all the developments that had gone before, and outlined the ways for a scientific approach to the subject. He gave us a starting point. Since then ore-dressing practice and technique in this country have set the pace for the world. Coal preparation has been called "ore dressing upside down,'' because in ore dressing we generally save a small percentage of the heavy valuable mineral and discard the lighter gangue, whereas in coal preparation we save the larger quantity of light mineral and discard the smaller percentage of heavy waste. By comparison with ore dressing the history of coal preparation is brief, extending backwards hardly 100 years, for although coal had been dug and used locally for centuries it became an important article of commerce only with the coming of the industrial revolution 150 years ago. In new mines it was to he expected that the thickest and purest seams should be worked first. So long as these lasted there was little thought of coal preparation other than hand picking of the larger impurities and simple sizing to supply the real or fancied need

Jan 1, 1934

By K. Huessener

This paper attempts a survey of the principles involved in the combustion of blast-furnace gas in boilers and stoves. I do not expect to be able to give much information which is actually new, since the laws and methods of calculation pertaining to this problem are contained in a number of handbooks; but, so far as I am aware, they have nowhere been treated exclusively with reference to this one problem of gas economy. The road which I follow is less that of strictly scientific research than that of the practical engineer, faced by operation problems which require a quick solution by easily accessible means without a prolonged search in scientific handbooks. For this purpose I give a number of tables and diagrams, as well as the results of many years1 practical working experience as combustion engineer, which I trust will prove useful to my readers. HlSTORICAL Considering the tremendous efforts made during the last 15 years to increase the efficiency of all kinds of power plants, it is highly surprising that until a comparatively very recent period, progress in the economical combustion of blast-furnace gas has been so slow, The explanation generally put forth, that fuel has been so cheap that it was hardly worth while to bother about this economy, will not hold good, for the greatest trouble was taken to improve the combustion of coal and to reduce the consumption of steam, The most plausible explanation appears to be the general impression, held as an accepted fact, that gas, especially hot, uncleaned, blast-furnace gas, was not a good boiler fuel. Many managers of high repute had tried unsuccessfully to improve the conditions of its use, and the dictum went forth that efficiencies of over 60 per cent., particularly with high loads, were impossible. This was the situation not only in the United States, with very cheap fuel, but also in Europe, where fuel prices are twice and three times as high.

Jan 1, 1916

By R. W. Winson

Asbestos is the generic name given to a group of fibrous mineral silicates found in nature. They are all incombustible and can be separated by mechanical means into fibers of various lengths and cross sections, but each differs in chemical composition from the others. The commercial grades of asbestos consist of a spectrum of lengths and sizes and are not definitive as are most organic fibers. It is generally recognized that there are two main groups of asbestos. The first only contains the fibrous serpentine called chrysotile and comprises about 94% of the world production of asbestos. The second group contains five minerals in the amphibole series+rocidolite, amosite, anthophyllite, tremolite, and actinolite. The latter two have no commercial importance. Properties Physical The structures of asbestos fibers have been studied intensively over a number of years. X-ray diffraction patterns have been used as a means of identification and classification. Low angle X-ray scattering techniques have shown that chrysotile fibers are "hexagonally close packed" and parallel to each other, having cross-sectional diameters varying from 18014 to 300A units, while the amphibole fibers are many times larger in cross section. Electron micrographs of the more common types of as- bestos are shown in [Figs. 1-4]. [Fig. 1] illustrates the softness and flexibility of chrysotile which make it suitable for textile-type products. For a number of years there was considerable controversy over the exact nature of chrysotile fiber, but the photographic evidence in [Figs. 5-7] clearly show that it is tubular in structure. The curvature is the result of the mismatch in the dimensions of the silica [Si,O,l and brucite [Mg(OH),] layers which are on the inside and outside, respectively, of a double sheet. This curvature had been predicted by Pauling (1930) years ago based on the molecular dimensions of the two component structures.

Jan 1, 1975

By G. R. Speich, D. J. Mack

The transformation of was studied by isothermal methods. At all temperatures, the ß transforms quickly to fine grained ß" which develops silver-rich striations. At higher temperatures the striations disappear, the final structure being Widmanstatten a in ß'. At lower temperatures, the striated ß" is consumed by pearlite nodules of a + ß' which in turn form the Widmanstatten a in ß'. The transformation is unlike any previously reported for a eutectoid. AS part of a general program of study on the eutectoid reaction, the Ag-Cd eutectoid seemed particularly attractive because the ß phase which undergoes the reaction is another of the typical "electron compounds," AgCd, having the disordered body-centered cubic structure. This work deals with the eutectoid which occurs at 50.5 wt pct Ag, and not with the eutectoid which has been reported at 42.9 pct Ag.' There has been no work reported specifically on the Ag-Cd eutectoid which was studied. The only information available on this eutectoid is that work done in the determination of the phase diagram. For the most part, the terminal portions of the diagram, Fig. 1, are well established; however, the region from 40 to 60 pct Cd is still somewhat in doubt. The X-ray evidence'..' in this region is in conflict with the results of thermal analysis. X-ray analysis3 does not show a polymorphic transformation at about 240°C as indicated by thermal analysis.1,5 Even the X-ray evidence, within itself, is confusing in this region of the diagram. One investigator2 reports the ß phase as hexagonal close-packed and has found three phases in the one-phase ß field. Other X-ray investigators"' ' report the ß phase as body-centered cubic. The authors believe that much of the confusion resulted from incomplete homogenization of the alloys. It was found that it takes almost a week to produce a completely homogeneous two-phase structure at 370°C. Another possible source of error is the volatilization of cadmium from the surface and cracks of the specimen during annealing with the possible formation of a cadmium-poor phase. The only metallographic data available on this eutectoid alloy are those of Durrant1 and Fraenkel and Wolff.5 his information is very limited. The phase diagram chosen as most nearly correct is that in the Metals Handbook," which is almost identical with the phase diagram suggested by Durrant.1 Materials and Procedure The alloy was prepared from high purity silver (999.5 plus fine) and high purity cadmium (0.02 Pb, 0.005 Cu, trace Fe). The metals were melted in carbon under a nitrogen atmosphere. Some cadmium was lost by volatilization but by remelting several times and adding cadmium a 200 g ingot of approximately eutectoid composition was obtained. Because the CdO fumes are quite toxic, the exit gas from the furnace was led through a water trap to condense the CdO. The ingot was homogenized at 650°C for 24 hr, no attempt was made to prevent decadmiumization. This resulted in a narrow decadmiumized rim on the ingot which was removed. Filings for analysis were obtained from cross sections of the ingot. Silver was determined by the Volhard thiocyanate method,? cadmium by difference. The ingot analyzed 50.8 pct Ag at the top of the ingot and 50.7 pct at the middle and at the bottom of the ingot. This alloy was only slightly hypo-eutectoid compared to the accepted value of 50.5 pct Ag and was used for the isothermal studies. It was felt that further attempts to adjust the composition might be futile because of the volatility of the cadmium. The ingot was sectioned to specimens approximately 3/4 x 3/4 x 1/8 in. These specimens were "austeni-tized" for 3 hr in air at 650°C to yield homogeneous ß and then quenched into a salt bath held at constant subeutectoid temperatures where the transformation

Jan 1, 1954

By Alexander R. Troiano, Taylor Lyman

Studies of the transformation of aus-tenite at constant subcritical temperatures have been numerous since the work of Davenport and Rain.' Considerable information has been obtained on low-alloy steels and on high-carbon alloys containing undissolved carbide or graphite at the austenitizing temperature. Little is known of the isothermal transformation of aus-tenite containing in solution large amounts of both carbon and a single alloying element. In this investigation four steels containing one per cent carbon and with chromium in the range 3 to 9 per cent have been examined with the view to establishing the fundamental character of the isothermal reactions when all carbon and chromium are initially in solution in austenite. Experimental Procedure Alloys The chemical compositions of the steels investigated are given in Table I. The 4 per cent Cr alloy is a commercial steel. The other steels were made by the Carpenter Steel Co. as 50-lb., induction-furnace heats and rolled to 5/8 -in. round bars. Bars were softened at 650' to 700°C. before the specimens were cut. Most of the lines on the transformation diagrams presented here have been placed on the basis of the microscopic examinatioll of partially reacted specimens, Thees specimens were approximately 1/2 by 1/4 by 1/8 in. ill size, specimens of the 9 per cent cr steel were held 10 to 12 hr, at 1200°to 1225°C. before quenching to the various subcritical temperatures. The other steels were held for 2 to 2 1/2 hr. at 12ooOC. before quenching. These treatments, carried out in an atmosphere of purified nitrogen, produced an austenite grain size larger than A.S.T.M. So. I, some grains being 1 to 2 mm. in diameter. There were a few undissolved carbide particles in some specimens of the 9 per cent Cr steel. It is believed, however, that any errors in the results due to incomplete solution of carbon and chromium in austenite are negligible; that is, austenite compositions may be considered as being those listed ill Table I. X-ray Methods Constituents were identified and mar-tensite axial ratios determined from Debye

Jan 1, 1945

By James H. Boettcher, W. Durand Eppler

INTRODUCTION In the second quarter of 1979, Rapid Mining Co., Inc. ("Rapid") inquired whether Crocker National Bank ("CNB") would provide $4 million in term loan financing to help ("Dry Creek") acquire the outstanding shares of the Dry Creek Coal Company ("Dry Creek") in West Virginia. Prior to approaching CNB, Rapid had sought financing with the assistance of a financial advisor from a number of commercial banks without success. A summary of the initial terms requested by Rapid is shown in Table 1 compared with the actual terms on which the transaction closed. It is not difficult to note that the two sets of terms differ significantly. This is often the case when financing requests based on the expectations and vision of a mine developer are juxtaposed with more pragmatic requirements of a commercial bank. The "art" and fund of structuring financing plans for mining ventures (highly leveraged acquisitions or grass roots) comes in working with mine developers to arrive at a final financial structure that meets their objectives and constraints as well as those of the bank or other financial institutions providing much of the financing. Beginning with the terms requested by Rapid and ending with the terms that closed the transaction, this article briefly describes the process we went through with Rapid Mining. The Seller and Buyer The Dry Creek Coal Company was established in 1961, after its owner acquired the coal leases from Republic Steel. Republic has mined the primary coal seam from 1948-1961. Dry Creek was owned as a subchapter S corporation (i.e., for federal income tax purposes, income is taxed at the shareholder level) and had been run on a low key basis. Since the company had virtually no debt and limited cash needs, the owner produced primarily when rail cars were available and income was required. Output was therefore erratic as is shown in the top of Table II, but the result was a profitable little company with an attractive free cash position. Because the owner wished to retire and enjoy his wealth in a more readily spendable form, he had put the mine, with stated recoverable reserves of approximately 13 million tons, up for sale. In contrast, Rapid Coal's investors consisted of a number of investors of disparate financial situations. They had agreed upon a primary objective of income maximization and planned an annual production rate of 120,000 TPA which they and the current owner believed realizable. The Formulation of a Financing Structure Figure 1 presents a simplified overview of the sequence of steps taken in the financing process which lasted approximately three months from start to finish. Since banks see many requests for funding and considerble time is required to follow up on each, an important step was determining, after a brief review of the materials provided to us, whether the basic "eonomic entity" was viable. In this case, the size and quality of the reserves, the inherent operating cost characteristics, the sales arrangements, the management/labor situation and Rapid's principles all appeared to be sound enough to warrant investing the time necessary to do a thorough analysis of the project. Once this decision was made, the evaluation and analytic process shown in Figure 2 was initiated. The first and most fundamental concern of any banker is whether the loan will be paid back as scheduled from the cash flow generated by the project. The amount of debt relative to the owner's equity is of course crucial in such a determination. Before the debt/equity issue was addressed, however, a number of more qualitative factors had to be studied and if

Jan 1, 1985

By Robert I. Jaffee, Bruce W. Gonser

RECENT work by the authors1 established the constitutional diagram of the gold-germanium system. Of particular interest in the simple euctectiferous system was the eutectic alloy at 12 per cent Ge, which melted at the very low temperature of 356°C. and had an unusually fine eutectic structure. It was of interest to investigate the effect of third components on the melting point, microstructure, and strength of this alloy, and in this work the effect of copper is discussed rather completely, with less complete data on the effects of silver, platinum, nickel, and zinc. No reference in the literature has been found on ternary systems with gold-germanium. MATERIALS AND ALLOYING As in the work on the binary system, gold-germanium, the germanium used in this investigation was the cyanide-reduced, 99.9 per cent product, produced by the Eagle-Picher Co. Fine gold sheet from Handy and Harmon, pure platinum sheet from the American Platinum Works, copper magnet wire from Anaconda, nickel wire assaying 99.6 per cent Ni, and electrolytic zinc were used for alloying. To make the alloys, charges of the pure metals were put in a graphite crucible and melted in an atmosphere of pure hydrogen. The temperature was brought up to about 1050°C., and the metal allowed to freeze in the crucible. Except with alloys containing zinc, melting losses were consistently less than a few milligrams. When zinc was a component, weight losses up to half the weight of the zinc present were incurred, and the alloy compositions were calculated by assuming the entire weight loss to be that of zinc. In all other cases the composition of the alloys could safely be taken as that of the charge. The ingots, as solidified, were segregated, the heavier primary phases being at the bottom and sides of the ingots and the lighter primary phases at the top, but by sectioning the entire ingot vertically for microscopic examination, this factor could be evaluated. Ingots for microscopic examination weighed one gram, and those for thermal analysis weighed three grams. THERMAL ANALYSIS In this work, the eutectic line composition and thermal arrests were desired, and, after microscopic exploration had established the position of the eutectic line at a given percentage of the third component, a thermal analysis was run at that composition. The method of thermal analysis used in the work on the binary Au-Ge system,1 a method particularly well suited for a small quantity of material, was used in this work. Clearly defined arrests were obtained, although with some alloys containing platinum

Jan 1, 1946

By Frank T. Sisco, Selma F. Hermann

gancse constituent in the alpha grains. Nickel produces a structure of alpha plus cutectoid almost identical with that of the normal aluminum bronze (Fig. 38), except for the rod-shaped nickel constituent in the alpha grains. Silicon produccs a light structure with small regular needles, possibly a modified form of beta. Fig. 45 shows the alpha plus beta structure of the normal 10 per cent. aluminum alloy as quenched. Manganese produces large grains of beta with alpha as a tiny constituent scattered throughout the spceimen. Silicon, on the other hand, produces all alpha, with free silicon present. One per cent. iron produces alpha plus beta, with a tiny constituent present in the alpha grains. Five per cent. iron introduces twins in the alpha and a nodular iron constituent in both the alpha and the beta. Figs. 50-58 include the structures of the alloys with 8 per cent, aluminum, tempered at 400" C. and at 650" C. Fig. 50 is the normal structure as drawn at 400" C!. It consists of large grains of twinned alpha plus a very small amount of beta. One per cent. silicon increases the amount of beta enormously, but when tempered at 650' C, the beta degenerates to a hard blue network constituent. One per cent. cobalt results in a structure of exceedingly fine-grained, twinned alpha, heavily mottled. Nickel produces large soft grains of alpha with a dot constituent in some of the grains, when tempered at 650" C. Manganese, when tempered at 400" C. produces alpha grains and shows the decom-

Jan 1, 1931