Search Documents

By R. A. Greenkorn

This project originated in a practical problem—we needed five tracers that could be used together to locate flow paths in a pilot flood. While tracers for subsurface liquids have been used since the turn of the century,1-15 none of those reported in the literature appeared to be either consistent or quantitative enough for our purposes. Most were used in field systems without controlled experiments to determine the accuracy and precision of analysis, and many were tracers that could not be used collectively. The ideal tracer, of course, would follow the fiuid of interest exactly, traveling at the same velocity as the fluid front. But the ideal is impractical to attain because adsorption-desorption effects cause the tracer to lag behind the front; these effects, plus diffusion-dispersion effects, cause the tracer front to spread more than the fluid front. Thus, our objective was not to locate a tracer that would be ideal for all circumstances but rather, to find one that would approximately follow the fluid, or one that under controlled conditions could be corrected to calculate the movement of the fluid front. We considered tracers satisfactory—(1) if they were easy to analyze; (2) if their breakthrough-elution curves were not too different from those for the chloride ion, a tracer believed to follow the fluid front closely; and (3) if we could calculate from the curves a material balance, at 1.25-PV (pore volume) injected, within 5 per cent of that calculated from chloride curves. Of a possible 35 materials, we selected 13 tracers that could be quickly and easily identified and whose analysis was claimed to be accurate within 5 per cent. Only one of these, tritiated water, was a radioactive tracer. Radioactive tracers are easy to detect even in small quantities, but they require special handling and special equipment. Also, those that can be used together are limited because special equipment is required to separate emissions from the various tracers. Two of the original 13 tracers were eliminated in static tests to determine how accurately and precisely they could be analyzed, and to check on gross adsorption. The remaining 11 were flowed through a 9-ft linear sandstone model, and breakthrough-elution curves were obtained. Finally, three tracers were field-tested as breakthrough tracers. These tests are described in the following sections. The 13 tracers considered in these experiments were EDTA (ethylene diamine tetra acetic acid), fluo-rescein, picric acid, salicylic acid and ammonium, boron (as borate), bromide, dichromate, iodide, nitrate and thiocyanate ions, plus chloride ion and tritiated water. All but the chloride ion and tritiated water were subjected to static sand tests to eliminate the tracers that could not be analyzed quickly and accurately and to eliminate those that showed excessive adsorption. All but two of the tracers, EDTA and salicylic acid, qualified for flow tests on this basis. The procedures used in the static tests (see Appendix A for analytical details) were as follows. Each tracer (in the amount shown in Table 1) was dissolved in 1,000 ml of water. Then, 800 ml of this solution was added to 500 gm of sand, and the remaining 200 ml was reserved as a control standard. The sand-tracer mixture was agitated once a day over a 10-week period, and during this period we analyzed five duplicate samples from this mixture, along with five duplicate samples from the control solution. From the control-sample analyses, we constructed a control chart on which the sand-tracer analysis results were plotted. The control chart, and its use to determine accuracy and precision of analytical results, as well as the amount of adsorption, is described in Appendix B. The results of the static tests are summarized in Table 1, which lists the concentration c (concentration at time t) divided by c, (initial concentration). If there was no adsorption, c/c, = 1. The acceptable deviation from this value varied from tracer to tracer, depending upon the limits of analytical precision established for the different tracers. The best results were obtained with boron, bromide and dichromate, with all values falling within limits of accuracy and precision. Ammonium, iodide, nitrate and picric acid also were satisfactory, although the ammonium results were erratic. Flourescein and thiocyanate were unsatisfactory ini-

By Carrol M. Beeson

Reasons are given for using a Boyle's-law porosimeter in conducting core analysis for either routine or research purposes. Among other things, it is pointed out that such a porosimeter permits the measurement of all basic properties on the same sample, thereby eliminating the sources of error inherent in the use of adjacent samples. References are made to investigations of gas adsorption on various porous materials, to show that the use of helium in Boyle's-law porosimeters reduces to negligible proportions the error due to the adsorption or desorption of the operating gas. Two Boyle's-law instruments are described. which permit accurate and rapid measurements of porosity. Schematic sketches and explanation:; are included, along with derivations of equations required in performing precise determinations. Summaries of data obtained during calibration are tabulated and analyses of the data are resented as indications of the precision and accuracy of each device. Comparisons are also shown for measurements made with each of the instruments on the same test pieces and cores. INTRODUCTION An accurate porosimeter, operating on the principle of Boyle's law. is of considerable value in the analysis of cores for either routine or research purposes. This is due primarily to the fact that the measurement of porosity with such an instrument leaves the sample free of contamination by any liquid. When used in conjunction with an extraction apparatus' for determining oil and water saturations, a Boyle's-law porosimeter permits the measurement of all basic properties on the same sample. This eliminates the sources of error inherent in the use of adjacent samples, or the necessity of determining porosity after all other properties have been obtained. Large errors may result from combining measurements made on adjacent samples in order to obtain a single property. This type of error is definitely involved when oil and water are measured with one sample, and the pore vo1ume is measured with an adjacent one. Furthermore, the source of error would be present to some extent, even if the analyst could choose the samples so they were truly adjacent from a geological standpoint. The use of adjacent samples in routine core analysis also necessarily decreases the probability of correlating core properties. For example, the chance of correlating the "irreducible" interstitial-water saturation with permeability, is bound to be greatly reduced by measuring these properties on "adjacent" samples. For research purposes, amplification is scarcely required concerning the greater flexibility of a method for measuring porosity which leaves the core free of contamination by any liquid. Even under those circumstances which require that the core be saturated with a liquid, a previous measurement of porosity with a gas is useful in determining the degree of saturation that has been attained in the process. Furthermore, for comparable accuracy, porosity usually may be determined more rapidly with a gas than with a liquid. This advantage of the Boyle's-law instrument is most outstanding when the determination time is compared with that required in obtaining porosity by evacuation of the core followed by saturation with a liquid of known density. Several porosimeters which operate on the principle of Boyle's law have been described2,3,4,5,6,7 in the literature. No comparison will be attempted between those instruments and the ones described herein. Before helium gas became readily available, Boyle's-law porosimeters were subject to an appreciable error due to the adsorption of the operating gas on the surface of the core solids. There is considerable direct and indirect evidence in the literature to support the contention that the adsorption of helium on porous solids is negligible at room temperature. In discussing the use of Boyle's-law porosimeters, Washburn and Bunting2 stated that "for most ceramic bodies dry air is a satisfactory gas, but hydrogen will be required in some instances. Helium could, of course, be employed for all types of porous materials at room temperatures or above." Howard and Hulett8 obtained evidence that the adsorption of helium was negligible at room temperatures, even on activated carbon ; for the density measured with this gas was unaffected by changes in pressure or by changes in temperature from 25 °C to 75 °C. For oil-well cores, Taliaferro, Johnson, and Dewees" obtained lower porosities with helium than with air, but apparently did not study helium adsorption. From the work of these investigators, it follows that the use of helium in Boyle's-law porosimeters reduces the error due to gas adsorption to negligible proportions. This makes it possible to construct instruments which permit the determination of porosity with (1) a high degree of accuracy, (2) with great rapidity, and (3) without contamination. THE KOBE POROSIMETER The fundamental design of the Kobe Porosimeter was developed by Kobe, Inc., which firm built about 12 of the instruments during 1936 and 1937. Since that time, seven or eight more have been constructed with their permission, making a total of about 20 that have been put into operation.

Jan 1, 1950

THE problem of reaction rates in the open-hearth process is essentially that of trying to form a fairly clear picture of the "chemical mechanisms" in the bath. Quantitative data on reaction rates would perhaps not be of much practical importance even if they were available; however, what few approximate data there are can be used in combination with data given in Chapters 16 and 17 to sketch a picture of the "chemical mechanics" of the open-hearth process that is consistent with essentially all the present available evidence. The result may later be found incorrect in many details but even so it will illustrate certain useful methods for obtaining a clearer understanding of the process. Consistent with the treatment in Chapter 15, but in simpler terms, we may say that chemical reactions in general involve the following elements or steps : 1. The reacting molecules are mixed together in space in such fashion as to favor collisions among them. 2. Units of what is usually an intermediate molecular arrangement called an activated complex are formed at a certain rate, depending on temperature and concentrations. 3. .These activated complex units decompose into the reaction products (this step usually assumed to be so rapid as never to limit the over-all process). 4. In any of these steps, heat energy may have to flow into, or away from, the reaction zone to permit the reaction to proceed. 5. The products of reaction will usually have to move out of the way to permit further reaction. The temperature factor enters mainly through step 2, and its effect is very marked. (What is called temperature is really the mean energy content of all the molecules of the substance involved; at any one temperature a certain proportion of the molecules will have much higher energy content than the mean value.) Various reaction rates measured at around room tem-

Jan 1, 1964

By Rudolph G. Wuerker

MUCH descriptive matter has appeared on the subject of suspension roof supports, or roof bolting, as it is more commonly called. The widespread introduction of roof bolting into coal mines and metal mines is truly phenomenal. Mine operators were quick to recognize the advantages of supporting wide openings without hindrance to machine maneuverability and ventilation. Although suspension roof support has long been installed at St. Joseph Lead Co. mines in southeast Missouri,'" its application to coal mining presented new problems, such as proper anchorage and bearing for the bolts, bolt diameter, and spacing of bolts. After continuous testing and experimenting at the mines, standard roof-bolting materials were determined.'!' The study reported in this paper is not concerned with such details as bolt diameter, which may be considered already solved in practice. In the tests discussed here, small models patterned on actual bolts were found to function in the same way and as satisfactorily as their prototypes. The aim of these tests was rather to investigate the influence of roof-bolting systems on the stress distribution around mine openings and to study the fracture patterns obtained in actual testing. Little was found about this in the literature, as testing of suspension roof methods and quantitative measurements are only now coming to the fore. Several suggestions and actual measurements have been made to evaluate critically the functioning of roof bolting systems, single roof bolts, and parts thereof. Outstanding among them is Bucky's outline of structural model tests.'" Since none of the suggested testing equipment was available, however, for the experiments discussed below, a different approach was chosen. The response of a mine roof under stress has often been compared to that of a beam. The slow coming down and bending through of beam or plate-like banks of shale, sandstone, or top coal is a familiar occurrence, extensively cited in the literature." It was felt that testing of roof-bolt systems installed in a concrete beam which was loaded in bending would be a fair approximation of the behavior of a mine roof underground. Another school of thought considers the roof behavior over an underground opening in connection with the stress distribution all around a circular or rectangular opening. This is more accurate, and leads to the concept of a dome-shaped zone of material destroyed under tensile stress. This is likewise a common sight in unsupported roadways where the continuous fall of roof results in what has been called the natural outline of roof fracture. This theory could not be tested and is treated separately in Appendix B. It is important to note that according to both assumptions the immediate roof fails in tension; the use of a beam in these tests, therefore, should give information valid for either of the two theories. With the testing equipment at hand it was possible to load concrete beams 6xlx0.5 ft under two-point loading, giving an equal bending moment over the center part in which the model bolts were installed. A comparison was made of the ultimate loads needed to break plain beams and beams in which roof bolts were installed. Arrangements were made with: 1—plain beams; 2—bolts with plate washers, some with holes drilled at 90" angles and others with holes drilled at 45" angles; 3—bolts with channel irons underneath; 4—bolts in holes filled afterward with cement; and 5—bolts anchored in a stronger stratum. The foregoing arrangement is made in order of increasing strength, as assumed from the theory of reinforced concrete. Likewise, laminated beams with wooden model bolts and with combinations of the foregoing set-ups were tested. All in all, 21 experiments were made out of the much greater number of combinations possible. There were, too, some trial tests. Enough observations from this limited number were made to interpret the behavior of mine roof, supported by various types of suspension bolts, at fracture. In present-day concepts, which have been proved by mathematical derivations and stress analyses, any opening driven underground will change the distribution and magnitude of the stresses existing around it. It does not matter whether the stresses become visible, as in rocks whose strength is less than the forces acting upon them, or whether they are invisible, as in the gangways lacking evidence of rock pressure. In this latter case the rocks can withstand changes in stress-distribution. To consider the mine roof as a beam, there are, with transversal loading, tensile stresses in the lower fiber and compressive stresses in the upper layers above the neutral axis of the beam. Beams of brittle material such as rock and concrete fail exactly as shown in Fig. 1. Nearly all model beams showed the same fracture pattern as that of a tension crack. The influence of support, by roof bolting or conventional

Jan 1, 1954

By W. N. Lacey, R. H. Olds, B. H. Sage

Samules of liquid and gas were obtained from the primary separator of a well in the Paloma field. The volumetric properties of the samples and of six systematically chosen mixtures of the samples were experimentally determined at 100°, 190°, and 250°F. at pressures up to 5000 lb. per sq. inch. From these data the influence ,of pressure and temperature upon the composition and specific volume of the bubble-point liquid and of the retrograde dew-point gas was established, The formation volumes and gas-oil ratios of the rnixtures investigated were calculated on the basis of the plant-product oil, which is defined as the isobutane and less volatile portion of each mixture. The results are presented in graphical and tabular form. The volumetric behavior of the mixture corresponding to that produced by the well at the time of sampling was determined for 235ºF., the reported reservoir temperature, by graphical interpolation of the experimental data with respect to composition and temperature. The results indicate that the well-production mixture probably existed as a gas at its retrograde dew point under the conditions of temperature and pressure believed to prevail in the producing zone at the time of sampling. The effect upon the phase behavim occasioned by the omission from the well-production mixture of certain components of intermediate molecular weight was investigated. In the first case, all of the isobutane and 11-butane, and substantially all of the iso-pentane, were removed from the mixture of trap samples corresponding to the well production. In the second case, all the propane, isobutane and n-butane, and substantially all of the isopentane, were removed. Both modifications led to considerable increases in the retrograde dew-point Pressure at 235ºF.; an increase of 558 lb. Per sq. in. above that of the unmodified well-production mixture in the first case, and an increase of 1208 lb. Per sq. in. in the second. It was concluded that the material? remaining after the removal of certain components of intermediate molecular weight could not be injected back into the reservoir in the saqe proportion in which they were produced without entailing appreciable loss of liquid material through condensation within the formation. Introduction Under the usual conditions of production practice, petroleum arrives at the surface of the earth in a physical state considerably different from that in which it existed in the underground reservoir. The relative rates of production and the properties of oil and gas measured at surface conditions do not constitute, in general, even a qualitative description of the fluids existing in the reservoir. The estimation of reserves and the attainment of optimum efficiency with regard to rate, quantity, and cost of production require accurate data concerning the physical properties of petroleum throughout large changes in pressure and temperature. Many schemes have been devised for predicting the behavior of propane, as it is encountered in nature? but the experimental work upon which these predictions are based has not, for the most part, been extended to the higher pressures that occur in practice, nor do these methods permit, as yet, the estima-

Jan 1, 1945

By Frederic Benard

PRIoR to 1936, the Ontario Refining Co. received all incoming blister copper from The International Nickel Company's smelter in the usual form of 460-lb. cakes, or slabs. These were received in open cars in lots of 250 pieces. At the refinery the cakes were unloaded onto narrow- • gauge cars, for convenient handling and pickup by charging cranes. In March 1936, an investigation was started on the feasibility of transferring converter copper in the molten state from the smelter to the refinery anode furnaces, a distance of 1 1/4 miles. Although common in steel practice, the transportation of blister copper in this form had not previoisly been attempted and a preliminary study of the various factors involved was therefore necessary. For this purpose, a series of experiments was made in which molten copper, removed at different stages during the furnace cycle, was held in a small portable holding furnace. This vessel was essentially a refractory-lined steel cylinder provided with ports for filling and emptying, heated by an oil burner. Dimensions of the steel shell were 3 ft. 10 in. diameter by 7 ft. 3 in. long, and thickness of refractories depended on the design and combination used for the particular experiment. The vessel was filled with approximately 2 1/2 tons of copper at a predetermined temperature, the lining having been preheated to a definite point by means of an oil burner. All openings were well luted and temperature readings were made every 15 min. by means of an immersion-type thermocouple. In this manner the rate of heat loss resulting with different refractory design could be developed. The ratio of exterior surface to weight of metal was taken into consideration in comparing the experimental results with what might be expected for a full-sized unit, and observations were also made on type and degree of slag accretion. It was not possible to get as much information on this latter point as desirable, but all evidence showed that the problem would be control of slag build-up rather than attack on refractories. From the information derived, and in consultation with the engineering staff of the supplying company, an order was placed for the first

Jan 1, 1944

By W. A. Oates, J. A. Lambert, P. T. GaIIagher

Monte Carlo methods have been used to compute the arrangements of interstitial atoms dissolved in tetrahedral sites in bcc lattices. It is assumed that the presence of an interstitial atom "blocks " a certain number of neighboring sites and prevents their occupancy. Sites "blocked" by more than one filled site are allowed for. The computed values of. the mean occupation number (defined as the ratio of the total number of sites blocked to the number of solute atoms are used to calculate the configurational entropies of the solutions. These entropies are compared with those resulting from previous theoretical studies of this problem and also with available experin~ental data for the p Zr-H, Nb-H, V-H, and Ta-H systems. Evidence is also given that the "blocking" explanation of low limiting compositions in these systems, rather than this being due to initial limitations on the number of sites available, is probably correct. THE ideal partial configurational entropy of mixing of an interstitial solute in a metal is given by: where p is the number of interstitial sites per metal atom and Xi is the atomic fraction of the interstitial. For the bcc lattice. which we shall be concerned with in this paper, the interstitial positions are shown in Fig. 1. It can be seen that for the tetrahedral sites, p=6. whereas for the octahedral sites, p = 3. Different emphasis has been placed on the relative importance of energy and entropy effects in determining deviations from ideality in interstitial solid solutions. In some cases the same system, e.g., Fe-C, has been described by the contradictory regular and athermal solution models indicating that the enthalpy and entropy functions, derived from equilibrium data, are frequently not accu.rate enough to differentiate between these treatments. However, for certain metal-hydrogen solutions the equilibrium data is available over sufficiently wide ranges of temperature and composition to permit a reasonably accurate determination of the compositional variation of the heats and entropies. Hoch&apos; has attempted to interpret the results of interstitial solid solutions in terms of a regular solution model. In the case of the Ta-H system where 13 = 6, this model entails fitting the experimental relative partial entropies of solution, asH, to the equation: where ASgs is the relative partial excess entropy of solution of hydrogen. Hoch found that the results of Mallett and Koeh1 could be fitted to this equation with an approximately constant value of AF up to XH = 0.25. However, it is apparent from the solubility isotherms in this system which become asymptotic to the composition TaH that, since (Xh /6 - ~Xh ) becomes infinite only at TaH6, it is necessary that AS<&apos; tends to infinity at TaH. In other words, the low saturation composition of TaH, instead of the anticipated TaH,, eliminates the possibility of applying regular solution theory to such systems. Rather large negative excess configurational entropies must exist at higher hydrogen concentrations in order to explain the lower saturation values. To account for these low limiting compositions and excess entropies two distinctly different approaches have been followed. Rees and many others1-l2 have assumed that not all interstitial sites are crystallographically equivalent with respect to the interstitial addition; that is, in Eq. [I] p is less than the value anticipated from geometrical considerations. To describe, say, a bcc metal-hydrogen system with a limiting composition of MH by this approach one would consider that p = 1 in the first instance instead of p = 6.&apos;j3 In some cases, nonintegral values of B have been taken in order to improve the fit with the experimental data over limited ranges of composition. The other approach which has been used to explain the low saturation compositions is to assume that, although all sites are available for occupancy, strong repulsive interactions exist between the neighboring interstitial atoms, and hence occupancy of any site excludes or blocks a certain number of neighboring sites from being occupied. Earliest treatments of this concept considered the exclusion of an integral number, of nearest-neighbor sites from being occupied at all concentrations. In this case, the partial configurational entropy is given by: These early treatments failed to allow for the overlap of the blocked sites which will arise at all but the very lowest concentrations. More recently attempts have been made to calculate the effect of this decrease in the number of blocked sites on the configurational entropy. Using the quasichemical treatment of interstitial solid solutions as given by Lacher and assuming that an infinite repulsive interaction energy existed between the solute atoms. atom obtained an approximate configurational entropy applicable to the blocking with overlap case:

Jan 1, 1970

By A. A. Smith, J. S. Smart

THE controlled amounts of phosphorus, arsenic, sulphur or selenium found in commercial coppers perform a variety of highly useful functions. Indeed, a large segment of modem copper technology is essentially dependent upon the presence of one or more of these elements. Consequently, the literature contains many references to their effects but the scope is broad and has been only partly covered. New data are presented herewith directed toward a better understanding of the basic behavior of these elements in copper, with particular emphasis on the composition range 0 to 0.05 per cent. These data are a part of a general program of research on the effects of impurities on the properties of oxygen-bearing and oxygen-free copper, other portions of which have been reported previously.1-2-3 Schematically, the behavior of individual elements is determined from measurements of conductivity and softening temperature,1, 2 and the binary alloys employed are synthesized from high-purity copper in order to eliminate interference from the effects of extraneous impurities. Alloys of selected composition were first prepared in the oxygen-free form by continuously casting the melts in the form of 3/8-in. diameter rod. Oxygen was added subsequently to portions of the alloys, either by remelting or by diffusion at 850°C. from a surface scale. Test wires were drawn one B. and S. number per pass, using four 30-min. 600°C. anneals at o.3125, 0.257, o.204 and o.162 in., and a final cold reduction of 95 per cent t0 0.081 in. Oxygen-bearing slugs made by remelting were hot-rolled to 5/16 in., drawn to 0.162 in., annealed for 30 min. at 600°C. and cold-drawn 95 per cent to 0.081inch. The alloys containing phosphorus, having been compounded very early in the program, were prepared in the form of 5/16-in. rod, and processed to wire with only the last three intermediate anneals listed above, all of these having been conducted in commercial nitrogen. In addition, the conductivity anneals on these alloys were also performed in the same atmosphere, and the small amount of oxygen present as an impurity in the gas resulted in some loss of accuracy at temperatures of 700° to 800°C., as will be shown later. Subsequently, the anneals for all oxygen-free alloys were conducted in hydrogen to prevent oxidation, and purified nitrogen was employed only for oxygen-bearing samples. All conductivity anneals were of one hour duration followed by a rapid quench in 10 per cent H2SO4. EFFECT OF PHOSPHORUS The widespread use of phosphorus as a deoxidant has resulted in universal appreci-

Jan 1, 1945

By P. W. Bakarian, John C. McDonald

Three magnesium alloys were processed in various ways to exhibit a wide variation in the ratios of yield strength and tensile strength in the rolling direction compared to the cross-rolling direction. Basal-plane pole figures were prepared from several specimens. A fair correlation was observed between the property ratios and the ratio of percent of poles oriented in the cross-direction quadrants compared to the percent oriented in the rolling-direction quadrants of the pole figures. THE modes by which magnesium crystals deform are such as to lead to marked preferred orientations in all forms of wrought products. The effect of the active modes at room temperature, coupled with these orientations, is often to produce a lower compressive yield stress compared to the tensile yield stress. The phenomenon is due to easy twinning in compression, and has been well-related to the preferred orientations as described by basal-plane pole figures of the hcp magnesium single crystal. The literature contains some information on the variation with test direction of the tensile properties of sheet, but no quantitative relationship to the observed pole figures has been established. These effects have been reviewed in the few com- prehensive treatises in English which have been written on magnesium technology and metallurgy.1°3 Roberts presents several pole figures, but no tensile-property data in the plane of the sheet. Raynor has no pole figures, but quotes Frommer&apos;s4 results. The information in Beck&apos;s compendium more or less parallels the results of Jones and powell.5 In both a Mg + 1.5 Mn alloy and a Mg + 4.6 A1 alloy, cold rolling was found not to change the general situation of higher properties in the cross-rolling direction,* than in the rolling direction. Thomas&apos;6 X-ray studies of Jones and Powell&apos;s specimens did not permit correlation of properties and preferred orientation. Ansel and Betterton7 report tensile and compressive properties on three other alloys as a function of degree of cold rolling, plus a recrystallizing anneal. As rolled, there was a change in anisotropy with degree of reduction, but all alloys were reasonably isotropic in tension when annealed. X-ray diffraction photograms illustrated the kinds of orientations present, but were not correlated with the properties. Bakarian8 has described a method of determining quantitatively a preferred orientation, and illustrated the method by applying it to pure magnesium and two of its alloys. This method was used in the present work as a basis for correlating the strength properties with the texture.

Jan 1, 1965

THERE can be little doubt in the mind of anyone of the great interest which has been provoked in the mining and petroleum industry by the com-paratively new geophysical methods of prospecting, after the sessions at this year&apos;s meeting of the Institute. Not only were the sessions very well attended but every¬one seemed most attentive. Although the discussion was somewhat limited in general, that may well be at-tributed to the newness of the subject. Two sessions on this subject were planned originally, but these gave insufficient time for the presentation of all the papers prepared and a third session was abso-lutely necessary. The first meeting dealt entirely with the gravity methods and was completed in the scheduled time owing to the fact that but two of the five papers listed were read. The second session was devoted to magnetic and electrical methods, the completion of which had to be carried over into the third period of geophysics. The first session on geophysical prospecting, and in-cidentally the first scheduled Institute meeting devoted entirely to this subject, was most appropriately opened by E. L. DeGolyer, the chairman of the session. It was through the efforts of Mr. DeGolyer that the first gravity work, as applied to prospecting, was under-taken in this country. Again most appropriately, the first paper presented was given by Donald C. Barton, who carried on the first work with the Eötvös torsion balance in America and aided materially in its development. A subject, the theory of which is so difficult to understand as it is generally presented, was so clearly illustrated and ex-plained by the speaker that even a novice could grasp the fundamentals. Dr. Barton, in showing actual re-sults obtained in torsion balance surveys with the in-terpretation of the sane and later drilling records, was free in stating that there are many limitations to the field in which this and the other geophysical instruments may be successfully employed. This paper called for considerable discussion relative to the application of the torsion balance to gravity surveys over various types of structures. During the course of this discus-sion a very important point was emphasized by the chairman, namely, that for successful application of any or all of the scientific methods of prospecting, a back-ground of experience is absolutely necessary to serve as a basis for further work. This can only be secured by contributions from the results of actual prospecting work.

Jan 3, 1928

By T. A. Read, M. S. Wechsler, D. S. Lieberman

A theoretical analysis of the austenite-martensite transformation is presented which predicts the habit plane, orientation relationships, and macroscopic distortions from a knowledge only of the crystal structures of the initial and final phases. THIS paper presents a new theory of the formation of martensite. This theory makes possible the calculation of the austenite planes on which the martensite plates form, the orientation relationship between the austenite and martensite crystal axes, and the macroscopic distortions which are observed. The only input data needed are the crystal structures and lattice parameters of the austenite and martensite. Considerable effort has been devoted over the past thirty years to the development of an understanding of the crystallographic features of martensite reactions. Much of this work has been done on steels and iron-nickel alloys, for which a great deal of data has been accumulated concerning the shape and orientation of the martensite plates, the relative orientations of the austenite and martensite crystal axes, and the observable distortions which result from transformation. These observations are reviewed in refs. 1, 2, and 3. The first major step toward an understanding of these phenomena was made in 1924 by Bain,&apos; who showed that the a body-centered cubic structure can be produced from the 7 face-centered cubic structure by a contraction of about 17 pct in the direction of one of the austenite cube axes and an expansion of 12 pct in all directions perpendicular to it. Since that time, most of the efforts at further interpretation have been made by investigators who have worked from the phenomenological data, incorporating some of the information from the lattice properties, and have sought an analysis into likely deformations which would produce the observed results."- "11 but the three most recent papers on the subject have already been reviewed in some detail." Machlin and Cohenl0 measured the components of the distortion matrix and verified that the habit plane is a plane of zero distortion and rotation for the (259) case. They showed that the measured distortion matrix, when applied to the parent lattice, does not yield the product lattice and hence some inhomogeneous distortion must occur. Frank,u working from the lattice properties and taking some clues from the observations, considered the correspondence of close-packed rows and planes in the austenite and martensite. He predicted substantially the observed lattice relationship and habit plane for certain steels which have a (225) habit. Geisler12 suggested that there is a natural tendency for the habit plane to be a (111) and postulated certain slip processes to account for the fact that the experimentally observed habit plane is irrational and deviates from the assumed one. The present work differs from previous treatments of martensite formation in that it permits calculation of all the major manifestations of the process. Habit plane indices, orientation relationships, and observable distortions are all calculated from a knowledge of the crystal structures of the initial and final phases alone. The calculations contain no adjustable parameters. The agreement found between calculated results and the observations reported in the literature constitutes powerful evidence in favor of the mechanism of martensite formation proposed. The theory is applicable to systems other than steel (as is discussed later in this paper) which exhibit a diffusionless phase change but because of the wide-spread interest in the austenite-martensite transformation, particular attention will be given to the iron-base alloys. For other systems which undergo a similar face-centered cubic to face-centered tetragonal transformation, the mathematical treatment is identical with that presented here. Hence the theory successfully describes the transformation in the indium-thallium alloy.&apos;" Homogeneous Transformation to Martensite The distortion which any homogeneously transforming volume of austenite undergoes in order to become martensite is shown in Fig. 1, as was first suggested by Bain.&apos; (This distortion will hereafter be referred to as the "Bain distortion.") This specification of a contraction along one cube axis ;ombined with an expansion in all directions perpendicular to this axis describes what is properly called the "pure" distortion associated with this transformation. The distinction between a "pure" and an "impure" distortion plays an important part in the discussion which follows. A "pure" distortion is characterized by the existence of at least one set of orthogonal axes fixed in the body which are not rotated by the distortion. (These are called the "principal axes" of the distortion.) No such set of axes exists in the case of an "impure" distortion. On the other hand, an impure distortion can always be represented as the result of a pure distortion combined with the rotation of the specimen as a rigid body. For a given impure distortion the corresponding pure distortion

Jan 1, 1954

By J. B. Umpleby

PRoduction engineering in 1927 may be characterized by a great. clarification of fundamental conceptions, and many improvements in technique. During the year the profession has received tnarked recogni-tion by the industry and to an extent never before attained has become an integral part of it. History Petroleum production engineering is a new profession. Prior to 1925, when this Institute undertook the work, no forum existed for the open discussion of its technical problems. There was no attempt at a handbook of the subject prior to "Petroleum Production Methods by J. R. Suman, in 1921, and no textbook prior to Petroleum Production Engineering" by L. C. Uren, in 1924. As late as 1926, only six schools and universities offered special courses in petroleum production engineering. Prior to about 1923, engineers engaged by oil companies were used almost exclusively for construction and location work. Two of the leading production engineers in the Mid-Continent field, although with their respective companies more than twelve years, were not definitely assigned to production work until 1924. Both men now head large departments giving almost their entire time to production problems. Because of the newness of the profession, the leading production engineers of today have had their fundamental training in mining, civil, mechanical and electrical courses. Not unlikely this diversified training is in considerable part responsible for the amazing growth of the profession. I believe, however, that recognition is due principally to economic pressure within the industry which has directed attention more and more sharply on costs and efficiency. After all, the justification for the growth and continued development, of the profession is to recover more oil from a given unit of sand at less cost per barrel. In this new profession, it seems to me that greatest progress will result from focusing thought and effort on this single objective, and if I might offer one suggestion to the com-

Jan 1, 1928

By Ralph Sweetser

THE Round Table. on Qualities of Pig Iron, under the auspices of the Joint Committee on Qualities of Pig Iron, which is made up of members of the American Institute of Mining and Metallurgical Engineers, the American Foundrymen&apos;s Association, the American Society for Testing Materials, the Gray Iron Institute, and the. Malleable Iron Institute, was held at the Palmer House, Chicago, Ill., on Oct. 1, 1935. PROCEEDINGS R. H. SWEETSER,* New York, N. Y.-Seven years ago last June we had a round table on qualities of pig iron1, and at that time the foundrymen were out with their battle-axes for the blast-furnace men, and the open-hearth men were doing the same thing. After that meeting there was really a determined effort to find out about the qualities of pig iron, and great progress has been made all along the line. This afternoon we want to have a frank discussion of the qualities of pig iron, whether it is the molten pig iron going into the steel plant, or cold pigs going to the different foundries. We ought to hear something from Dr. J. T. MacKenzie, who is chairman of the Joint Committee, and from Mr. R. E. Kennedy, the tech-nical secretary. J. T. MACKENZIE, t Birmingham, Ala.-As a result of that meeting in Chicago, there was considerable agitation in the Foundrymen&apos;s Association to develop a set of tests for pig iron. One of the difficulties was that nobody talked the same language on shrinkage, draws, live iron, dead iron, and so forth, which were the main com-plaints against pig iron. By request of a committee of the Foundrymen&apos;s Association, the Bureau of Standards ran a comprehensive set of tests that did develop the prin-ciples governing the optical pyrometer as applied to cast iron and pig iron. Then the Bureau went on further with the fluidity test, and developed a method for the absolute changes of volume at the freezing point.

Jan 1, 1936

By K. Huessener

INTRODUCTION THIS paper attempts a survey of the principles involved in the com¬bustion of blast-furnace gas in boilers and stoves. I do not expect to be able to give much information which is actually new, since the laws and methods of calculation pertaining to this problem are contained in a number of handbooks; but, so far as I am aware, they have nowhere been treated exclusively with reference to this one problem of gas economy. The road which I follow is less that of strictly scientific research than that of the practical engineer, faced by operation problems which require a. quick solution by easily accessible means without a prolonged search in scientific handbooks. For this purpose I give a number of tables and diagrams, as well as the results of many years&apos; practical working experience as combustion engineer, which I trust will prove useful to my readers. HISTORICAL Considering the tremendous efforts made during the last 15 years to increase the efficiency of all kinds of power plants, it is highly surprising that until a comparatively very recent period, progress in the economical combustion of blast-furnace gas has been so slow. The explanation generally put forth, that fuel has been so cheap that it was hardly worth while to bother about this economy, will not hold good, for the greatest trouble was taken to improve the combustion of coal and to reduce the consumption of steam. The most plausible explanation appears to be the general impression, held as an accepted fact, that gas, especially hot, uncleaned, blast-furnace gas, was not a good boiler fuel. Many managers of high repute had tried unsuccessfully to improve the conditions of its use, and the dictum went forth that efficiencies of over 60 per cent., particularly with high loads, were impossible. This was the situation not only in the United States, with very cheap fuel, but also in Europe, where fuel prices are twice and three times as high.

Jan 2, 1916

By W. F. Boericke

INTRODUCTION THE Wisconsin zinc district, or the Upper Mississippi lead. and zinc district as it is also termed, lies in the southwestern corner of Wisconsin, and embraces adjacent portions of Illinois and Iowa. It includes Iowa, Grant, and Lafayette counties in Wisconsin, and Jo Davies county in Illinois. In Iowa, Dubuque formerly produced considerable lead, but there has been little mining there in recent years. The map, Fig. 1, shows the entire district, with roads, railways, streams, and the various towns, or "camps," around Which the mines. are clustered. The hatchwork indicates the areas iii which lead and zinc have been mined. The district is about 60 mi. (96 km.) north and south and about 40 mi. (64 km.) east and west. Not all of the territory is mineral bearing, and there are considerable areas that are believed to be barren. The grouping of the mines is patchy and irregular, though certain broad zones of mineralization extend almost the full width of the district, as from Mineral Point west through Mifflin and Livingston, and from Shullsburg west through New Diggings and Hazel Green. It is worth noting that the best mines of the district have, to date, been found within 10 mi. east or west of the fourth principal meridian line, thus lying within a long, narrow, north-and-south belt extending the length of the district. In a field as large as the Wisconsin, which has only within com-paratively recent time been worked intensively for zinc, the. chances are good for, opening new and important orebodies in parts of the district not yet, or insufficiently, prospected. However, the prospecting has been most successful around, or adjacent to, the old lead diggings of nearly a century ago, and the camps that were well known then are still centers of activity. In their order of importance they are: New Diggings, Benton, Mifflin-Livingston, Galena, Linden, Hazel Green, Shullsburg, and Highland.

Jan 8, 1919

By C. A. Pierce

STUDIES of roof and floor movement are of interest to those actively engaged in mining. This is especially true in the case of an entirely new area where there is no precedent for guidance. The potash deposit being mined is in the southeast corner of New Mexico, about 20 miles east of Carlsbad. The deposit was formed by the land-locked, shallow, Permian Sea that extended through parts of western Texas, Oklahoma, Kansas, southeastern Colorado, and eastern New Mexico. The saline deposits vary from 500 to 4000 ft. thick. Neither of the companies operating in this area has delimited its com-mercial ore bodies. As all production so far has been from Federal and State leases, the Department of the Interior and the State of New Mexico have a direct interest in the development and extraction of these ore horizons. The ore is composed of an intimate mechanical mixture of sylvite (potassium chloride) and halite (sodium chloride). It lies generally in a horizontal bed varying from 5 to 12 ft. in thickness, and has a cover of approximately 1000 ft., consisting of about 500 ft. of salt beds and 500 ft, of sediments. The immediate mine roof for several feet is principally salt with some potash and clayey material. The next 500 ft. above, from the standpoint of structure, may be considered rock salt with a few inter-bedded potash members. The upper 500 ft. is of sedimentary (Permian and Triassic) origin and contains several water-bearing formations with flows varying from 10 to 500 gal. per minute. This water intensifies the interest in convergence problems as the ore and surrounding for-mations are water soluble. Potash salt (sylvite) and rock salt (halite) are plastic minerals. Plasticity is defined as a "property of solids by virtue of which they hold their shape permanently under the action of small shearing stresses but are readily deformed, worked, or molded under larger stresses."1

Jan 1, 1938

AT A MEETING of the Shareholders of the Russo-Asiatic Cons. Ltd., in London, Oct. 23, 1922, LESLIE URQUHART, chairman of the com- pany made the following statement:* I come now to our recent negotiations with the Soviet Government and to the agreement which has resulted from them. You will remember that the conference at The Hague broke up without having achieved anything very definite. It was not, however, a failure. It elicited from M. Litvinoff an offer which will, I think, come to be regarded as a milestone in the progress of Russia from a ruinous and unpracticable Communism towards a modified form of capitalism. The offer made by M. Litvinoff at The Hague amounted in effect to this: that in return for political recognition on our part the Soviet Government would first acknowl-edge its liability for Russia&apos;s national foreign debts, and, secondly, would give the original foreign owners of property in Russia effective compensation. A very great advance that. It showed-and there have been many other signs to confirm it-how real and persistent has been the internal evolution of Russia during the past year from Marxism to the economics of the Western world. I will not now detain you with the reasons why M. Litvinoff&apos;s highly promising and significant offer came to nothing. The fact that it had been made and the further fact that The Hague Conference had separated indefinitely were the important things. The first fact seemed to indicate that the Soviet rulers, after all, proved to be people with whom one could do business. The second fact rather emphatically showed that the way to do business with them was not by unwieldy poly-glot conferences of ministers, officials and experts representing a few dozen different governments and a few dozen different sets of national interests. That method had been tried at Genoa. It was tried again at The Hague. Each time it failed, and having failed it left the road clear for a simpler and more direct approach.

Jan 12, 1922

By Walter Bradley

MINING by hydraulic process of the important gold-bearing gravels of the Sacramento Valley in the basins of the Yuba, Bear and American rivers began in 1853, and continued at an ever-increasing rate for 30 years. In its most active days it reached an annual production of $15,000,000, and averaged $10,000,000 per year over the 30 years. During that period no provisions were made to prevent the debris from being dis-charged into the water courses, and ultimately large quantities of silt, sand and gravel were washed down to the lower valleys; filling channels, causing overflow of agricultural lands and difficulty in maintaining navigable depths in the Sacramento River. Agitation and suits filed because of these damages finally resulted in the injunction decision of Judge L. B. Sawyer,1 in the U.S. Circuit Court, Jan. 23, 1884, which closed down practically all hydraulic mining operations not having means to restrain their debris. In 1893 (approved March 1, 1893), Congress passed the act introduced by Representative Anthony Caminetti, of California, creating the California Debris Com-mission, composed of three officers assigned from the Engineer Corps of the U.S. Army, and since that time it has been legal and possible within the drainage systems of Sacramento and San Joaquin rivers to conduct hydraulic mining of gold-bearing gravels behind dams built under this commission&apos;s permit and supervision. In the watersheds of the Trinity and Klamath rivers, which flow directly to the Pacific Ocean and do not affect navigation or agriculture, operating permits from the California Debris Commission are not required. There is a measure of restriction there, however,. through what is known as the Trinity and Klamath River Fish and Game Dis-trict. Chap. 215, Stat. 1931, in order to secure relatively clear water for the fishing season, provides that between July 15 and October 15 each year there must not be discharged into these rivers debris that will cause a turbidity greater than a content of 50 parts per million in the

Jan 1, 1936

By Eugene Grace

IN THE careers of the men to whom I have referred we find typified the development of the chief prob-lems of engineering. The first is to shape and direct the forces of nature and thus to bring the world&apos;s resources to add to the comfort and welfare of man-kind. That, in a word, is the problem of production. Engineers have made a supreme contribution to the solution of that problem. But I feel that we have two somewhat newer branches of engineering which must command more and more of our attention. Those are what might be termed commercial and human engineering. Of what value is all our efficiency in pro-duction if we do not distribute efficiently, economically and effectively? And of what value is any of it unless we can add to the happiness and deeper satisfaction of those engaged in industry, as well as those who enjoy its -products? I predict that the outstanding advances in business over the next ten years will be in improved merchan-dising and distributing methods. Herein lies a wide field of opportunity for the engineer. We have briefly reviewed certain qualities of engi-neers who have become successful business executives. Is it possible for us to say that the material success of all these men was due to any one characteristic com-mon to each one of them? Indeed, I venture to assert that there is one quality which, in the last analysis, is determining as to whether any roan shall realize material success in this world of ours. That quality-so notable in the character of each one of the men I have named-is sound judgment. Moments arise in every life when it is necessary to say "yes" or to say "no" to a particular proposition or to a proposed line of action. It is the man who says "yes" at the proper time and "no" at the proper time who, in the final analysis, realizes business success. The ability to do this wisely is the mark of sound judg-ment, which is necessary in a business executive. I have known many business men seemingly slow in their mental processes, possessed apparently, of little imagination and of none of the flair which gives fasci-nation to so many characters, and yet who, when crises come-be they big or be they little-are able so to steer their business courses that they move in the right direction instead of into shallow waters or upon the rocks of trouble.

Jan 4, 1928

By J. T. Raleigh, D. L. Flock

This study investigated the nature of formation plugging with bacteria and attempted to relate its characteristics to physical rock properties. Fifteen core samples of four specific formation types were defined and plugged using a commonly occurring, uniform sized dead bacteria, Bacillus subtilis. Two of the formation types were fairly uniform-grained sandstones and two were heterogeneous carbonates. The injection rate and concentration of solids in the brine were held constant during the test runs. The pore geometry factor G was a significant petro-physical rock characteristic for correlation with depth of plugging, but lacked importance as a parameter for rate of plugging. Although the G factor may not completely describe porous rock geometry for plugging predictions, for reservoirs with multi-pore systems, there is evidence that the pore geometry factor might form a basis for establishing injection water specification in more llornogeneous reservoirs with only primary porosity development. INTRODUCTION GENERAL PURPOSE Injecting water into oil-bearing formations to increase recovery is common practice in the petroleum industry. One of the most serious operational problems involved with water injection wells is the tendency of the porous rock immediately adjacent to the injection wellbore to plug partially. This results in increased injection pressures and/or a decrease in the rate of injection. This plugging in injection wells can result from a number of causes, including bacteria contained in the injected water.1 The purpose of this work was to investigate the nature of injection plugging with bacteria and to attempt to relate its characteristics to physical rock properties. Many variables exist in research of this type, so, to reduce them, injection rate and concentration of bacteria in brine were held constant. The bacteria used for plugging was a uniform-sized, dead bacteria, Bacillus subtilis, a micro-organism commonly found in water, air and soils. Four specific porous rock types were plugged—two consolidated sandstones and two heterogeneous carbonates. The experimental work involved two distinct phases. The first concerned determining the physical rock properties and the second was the experimental work of actually plugging the selected core samples. PORE GEOMETRY FACTOR Capillary pressure is necessary to displace a wetting fluid from a capillary opening with a nonwetting fluid. The factors which govern capillary pressure are the surface or interfacial tension of the fluids involved, the system wettability and the equivalent pore radius. Thus: P,= 2ucososrd..........(1) Thomeer used the idea that the location and shape of the capillary pressure curve reflect characteristics of the pore structure of any porous media sample.&apos; He presented the mathematical description of capillary pressure curves and of indicated differences in pore geometry of samples. where G = pore geometry factor PC = capillary pressure Pi = displacement pressure (V,)p, = fractional bulk volume occupied by the displacing fluid at any capillary pressure (V,), = fractional bulk volume occupied by the displacing fluid at infinite pressure or total interconnected pore volumes. The shape of the curve is defined by the pore geometry factor G. The curve shape is related directly to the sorting and interconnection of the pores of the sample. The location of an infinite number of curves can be defined by the same asymptotes. However, these curves differ in shape, each curve being described by a specific value of G. Thus, the description of a curve is unique when, in addition to the position of its asymptotes, its shape is defined. These curves can be used graphically to determine the characteristic parameters of any arbitrarily located curve. Those parameters that can be approximated from any capillary pressure curve are: (1) total interconnected pore volume, represented by (V,),- ; (2) extrapolated displacement pressure, the abscissa axis; and (3) pore geometry factor, by the curve shape. PROPERTIES OF BRINE AND BACTERIA The fluid used throughout this study was an aqueous solution of sodium chloride, 25,000 ppm by weight. The addition of salt to fresh water was intended to eliminate clay swelling in the sandstone cores and to retard leaching in the limestone cores. The viscosity of the brine solution at 100F, the temp-

Jan 1, 1966