Search Documents

By H. L. TERWILLIGER

THOSE of us who have been following rock drilling work for the last 15 or 20 years can recall some of the problems that were encountered with the old piston type of rock drill and the solid steel which it used. There was frequent trouble in keeping a straight hole in badly broken ground when using the ordinary four- point bit that had a flare on the wings of about 14". The drill steel, when pounding down its hole, would follow the line of least resistance and draw away from the desired line when it encountered a weak side in the ground through which it was drilling. Some would overcome the difficulty by making long winged bits to prevent the steel crowding over; this would relieve the troubles to a great extent. There was trouble with the rifling of drill holes and inability to drill round holes in some ground. The cure for these ills was to use the "X" bit, rather than the crossbit. The "2" bits were brought out in an effort to make it easier to drill a round hole in bad ground. Most of these troubles were before the days when the mechanical drill sharpener was in as common use as it is today. It was not until the introduction of the Leyner type of rock drill, requiring hollow steel that the users of rock drills found themselves confronted with more difficult prob- lems than they had ever encountered before with drill steel because the steel had to stand more severe service.

Jan 1, 1924

SUDBURY ore processed by International Nickel Co. of Canada Ltd. was recovered for many years as two mill concentrates, one primarily of copper, and the other mixed pentlandite-pyrrhotite, But, Since iron content of the nickeliferous pyrrhotite concentrate was ten times its nickel value, capacity of smelting was limited by the need for slagging the excess iron. A process for recovering the iron con- tent was developed after some years of research and a $20-million plant was constructed to employ the new method. Built near Copper Cliff, Ont., the plant started operation early in 1956, scheduled for separate treatment of 365,000 tons of pyrrhotite each year. It is only the first unit of an installation which will have a capacity of more than 1 million tons per year of pyrrhotite. By early 1958, production totaled more than 200,000 long tons of 68 pct Fe pellets containing 0.003 pct P, 1.5 pct SiO2, 0.01 pct S, and 0.15 pct Ni.

Jan 8, 1958

By Kyle Wightman

INTRODUCTION CRA Limited is the largest mining group in Australia by value of sales and the second largest company in Australia in terms of share market capitalisation. In the past 25 years, CRA, its predecessors and affiliates have been involved in a number of mining and further processing developments in Australia and elsewhere. Many of these have been financed using project financing techniques. These include Comalco's development of the Weipa bauxite deposits in Northern Queensland in the late 1950's, the Hamersley iron ore developments in the Pilbara region of Western Australia in the mid 1960's, the Queensland Alumina Limited alumina refinery in Gladstone, Queensland, at about the same time, and the Bougainville copper project in 1969/70. In the past three years CRA has again utilised project financing techniques to fund its Tarong steaming coal project in Queensland, the Blair Athol steaming coal project also in that State and CRA's interest in the Argyle diamond project in the Kimberley region of Western Austrlia. PROJECT FINANCE DEFINED Nevitt Definition Nevitt's is the most frequently quoted definition - "A financing of a particular economic unit in which a lender is satisfied to look initially to the cash flows and earnings of the economic unit as the source of funds from which a loan will be repaid and to the assets of the economic unit as collateral for the loan." Risk and Balance Sheet Treatment It is important to focus in more detail on two aspects of project financing, risk and balance sheet treatment. The assessment of the various elements of risk in a project and the sharing of that risk between sponsors and lenders is the most critical feature. At one end of the spectrum is full absorption of risk by the sponsor(s). This can be described as "on risk" or "on credit" or "full recourse" to the sponsor(s) and is effectively a corporate financing. At the other end of the spectrum the lenders absorb the whole risk in a non-recourse financing which is "off risk" or "off credit" for the sponsor. The other aspect is the sponsor's balance sheet treatment. If the balance sheet of the economic unit undertaking the project and the financing need not be consolidated into the balance sheet of the sponsor (because ownership does not exceed 50%) then the financing may be described as off-¬balance sheet. If consolidation is required then the financing is described as on-balance sheet. Most project financings involve some recourse to the sponsor, i.e. they are limited recourse. Very few are non-recourse or off credit to the sponsor. Limited recourse financings may be on-balance sheet although many may also be off-balance sheet insofar as consolidation is concerned. However, sponsor support may very well be a contingent liability to the sponsor and require disclosure by way of note to the balance sheet should consolidation not be required. CORPORATE FINANCE CONTRASTED A financing which is on credit or full recourse to the sponsor, whether it is directly borrowed or guaranteed by that sponsor, is a corporate financing. Lenders will tend to base their credit assessment on a historical assessment of the sponsor's activities and its financial results rather than an assessment of the project or a detailed assessment of the future activities and prospects of the sponsor. PROJECT FINANCE - A BORROWER'S PERCEPTION Although CRA could choose to arrange all finance on a corporate basis (except perhaps for the very largest projects or acquisitions), project financing techniques provide a number of specific advantages which CRA has noted and which should be carefully considered by a project sponsor. Advantages

Jan 1, 1985

By J. L. SILSBEE

THE existence of large saline deposits in that flat arid basin, known as the Great Salt Lake Desert, has long been recognized, but the extent and great commercial value of these deposits has not been generally appreciated. That a very considerable interest has recently developed is indicated by the fact that about 263 prospecting permits-each covering about 2560 acres of land in this Desert-have been issued under the Potash Leasing Act (Act of 0ct. 2, 1917-40 Stat. 297), and patents granted on approximately 40,000 acres. It is reported that patents and leases have, or will be applied for on an additional 80,000 acres in the basin. , Tests have been made on probably less than 10 per cent. of the total area of the basin, but these have proved a practically unlimited supply of brine available -sufficient, probably, to. furnish the potassium and magnesium chloride requirements of this country for at least a hundred years.

Jan 1, 1925

By R. Schuhmann

Distribution of material in the fine sizes of a comminution product generally is well represented by the empirical equation' y = 100 (x/k)a [1] in which y — cumulative percent finer, x = particle size, a -= distribution modulus, and k = size modulus. Charles3 found that the energy consumption in comminution is usefully expressed by another empirical relation, E = Ak(1-D) [2] in which E = energy input per unit volume of material, A = a constant, k = size modulus based on Eq. 1, and n = a constant; (1-n) is the slope of a plot of log E vs log k. Holmes3 has presented energy equations similar to Eq. 2. The constants a and n in Eqs. 1 and 2 have been shown to depend both on the nature of the material and on the comminuting device. Moreover, Charles showed that within experimental error a and n are a — n+1 = 0 [3] Combining Eqs. 2 and 3, E = A k-a [4] In the first sections of this article it is shown that the energy equation, Eq. 4, can be derived directly from the size distribution equation for the fine sizes, Eq. 1. The derivations are made without assuming any of the specific relationships between energy and particle size which have been common in previous literature. For comminution processes in which Eqs. 1 and 4 adequately represent the experimental data, the constant A in Eq. 4 is found to be a simple and useful inverse measure of grindability. That is, A is the energy consumption per unit volume of comminution product finer than unit size as determined from the straight line portion of the log-log plot of the size distribution. These considerations all lead to a unifying hypothesis of comminution mechanism from which both Eq. 1 and Eq. 4 can be derived. Finally, it is pointed out that this hypothesis raises serious questions as to the significance of the Rittinger hypothesis, the Kick hypothesis, and other theories in which energy numbers are systematically assigned to various size fractions of comminution products in order to calculate theoretical energy consumptions. Derivation of the Energy Equation from the Size Distribution Equation: For simplicity, consider the comminution of 100 volumes of a feed material of relatively uniform particle size. The comminution process may be considered as the summation of many individual and independent comminution events. The extent of comminution is most easily expressed as the number of comminution events, z. In the first derivation, the key assumption is that the characteristics of the comminution events in a given crushing or grinding process are substantially constant and do not vary with the progress of the comminution process. Accordingly the characteristics of an average comminution event may be defined. In one such event, a quantity of energy $E is applied to a single particle of size f and volume $v. The crushing of this particle produces fine particles with a size distribution similar to that given by Eq. 1: yw=100(x/ka)a0 [51 In this equation yo, a0, and k0 are used to characterize the product of an individual comminution event rather than the product of the comminution process as a whole. In using Eq. 5, we will not be concerned with values of x close to the feed size f and will therefore assume only that the equation is applicable to the finest sizes of the material. In 100 volumes of total product, the actual volume of product finer than x from a single comminution event, or dy, is given by The total volume of material below size x, resulting from z events, is then given by y = z(dy) =z(dv) (x/ka)a0 =" Eq. 7 reduces to Eq. 1 when we let a, = a and [8a] z =100/dv (ka/k )1 or k = ka (zdv/100)-1/a [8b] Eq. 8a shows that the distribution modulus of the comminution product is the same as for the product of an individual comminution event. Eq. 8b shows how the size modulus of the comminution product k varies with the extent of comminution as measured by the number of events, z, or as measured by the fraction of the feed actually subjected to com- minution1 zdv/100. The energy input to 100 volumes of total feed, or 100E, is the sum of the energy inputs for all the comminution events: 100E =z (dE) [9]

Jan 1, 1961

By R. S. Busk, R. F. Marande

The magnesium-aluminum-zinc 'system contains most of the magnesium-base alloys used commercially, although in practice the ternary alloys are usually modified by the addition of a small amount of manganese. Table I contains the magnesium-base commercial sand-casting alloys most widely used throughout the world, together with their typical tensile properties. These alloys may be regarded as a single family of varying aluminum and zinc content, disregarding manganese. A concise means of presenting data for them is by means of iso-property lines plotted on triangular coordinate paper. Constitutional, casting, and mechanical properties are presented in this manner. The data are given with the obiect of providing reference material, and to aid in the choice of a commercial alloy to serve a particular purpose. Detailed, critical analysis of the commercial alloys has been covered in a previous paper.' All alloys reported were made in rj-lb. melts, superheated to r700°F. for 15 min., cooled to r400°F. and poured in sand molds. The test bars produced had a 1/2-in. reduced section and were about 6 in. long. Except for the data represented in Figs. I and 3 the alloys used were of commercial purity and contained 0.1 to 0.2 per cent Mn in addition to the aluminum and zinc. Constitutional Data Under the heading of Constitutional Data are included all known data on con-

Jan 1, 1946

By R. F. Marande, R. S. Busk

The magnesium-aluminum-zinc 'system contains most of the magnesium-base alloys used commercially, although in practice the ternary alloys are usually modified by the addition of a small amount of manganese. Table I contains the magnesium-base commercial sand-casting alloys most widely used throughout the world, together with their typical tensile properties. These alloys may be regarded as a single family of varying aluminum and zinc content, disregarding manganese. A concise means of presenting data for them is by means of iso-property lines plotted on triangular coordinate paper. Constitutional, casting, and mechanical properties are presented in this manner. The data are given with the obiect of providing reference material, and to aid in the choice of a commercial alloy to serve a particular purpose. Detailed, critical analysis of the commercial alloys has been covered in a previous paper.' All alloys reported were made in rj-lb. melts, superheated to r700°F. for 15 min., cooled to r400°F. and poured in sand molds. The test bars produced had a 1/2-in. reduced section and were about 6 in. long. Except for the data represented in Figs. I and 3 the alloys used were of commercial purity and contained 0.1 to 0.2 per cent Mn in addition to the aluminum and zinc. Constitutional Data Under the heading of Constitutional Data are included all known data on con-

Jan 1, 1946

By John A. Gann

The following investigation constitutes a brief réumé of the more important binary magnesium alloys from the standpoint of metallo-graphic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn. Preparation of Alloys All melts were made in an oil-fired cast-steel pot, approximately 12 in. dia, by 12 in. deep. Approximately 15 lb. of flux and 50 lb. of magnesium were melted and the calculated amount of alloying metal was added. After thorough alloying and puddling, the metal was chill cast in a graphite mold with four 1/2 by 1/2 by 4 in. bars fed from a common sprue and runner. The next higher composition alloy in a given series was made by adding the calculated amount of metal to the heel from the preceding cast. The pot was thoroughly cleaned after each series and new flux then introduced, thus avoiding possible contamination from earlier melts. The percentage compositions given in Table 1 are the calculated values. While not all alloys were analyzed, enough were checked to indicate that the reported compositions are correct to a few tenths of one per cent. A more detailed description of the foundry methods employed has been given in a previous paper. 1

Jan 1, 1929

By John A. Gann

The following investigation constitutes a brief réumé of the more important binary magnesium alloys from the standpoint of metallo-graphic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn. Preparation of Alloys All melts were made in an oil-fired cast-steel pot, approximately 12 in. dia, by 12 in. deep. Approximately 15 lb. of flux and 50 lb. of magnesium were melted and the calculated amount of alloying metal was added. After thorough alloying and puddling, the metal was chill cast in a graphite mold with four 1/2 by 1/2 by 4 in. bars fed from a common sprue and runner. The next higher composition alloy in a given series was made by adding the calculated amount of metal to the heel from the preceding cast. The pot was thoroughly cleaned after each series and new flux then introduced, thus avoiding possible contamination from earlier melts. The percentage compositions given in Table 1 are the calculated values. While not all alloys were analyzed, enough were checked to indicate that the reported compositions are correct to a few tenths of one per cent. A more detailed description of the foundry methods employed has been given in a previous paper. 1

Jan 1, 1929

R. B. BRINSMADE, Ixmiquilpan, Hgo, Mexico* (written discussion). As the discussion of Mr. Graton's paper by Messrs. Norris, Patterson, and Crane has been from the standpoint of the mineral land-value owners, a few remarks in the interest of the "under dog"-the average taxpayer and citizen-may prove timely. In my discussion of Doctor Raymond's Paper1 and of the papers of Messrs. Gibson2 and Godson, 3 have endeavored to demonstrate, from both political economy and history, that our existing system of unrestricted private ownership of land is incompatible with equality of economic opportunity and, therefore, subversive of our democratic political institutions. In Mr. Graton's paper, the same land problem is important, though camouflaged by the failure of the Federal income tax laws to distinguish between land and capital, in the requirements for valuation, or between earned and unearned incomes in the levying of taxes. I disagree with Mr. Graton's statement, on p. 2967, as follows: The immense majority of mining ventures are failures. A multitude of disappointments is relieved by occasional success. Were it not for the chance of great rewards, all the vitally necessary but mainly unremunerative work of exploration would not be undertaken. In contrast with nearly all other fields of endeavor, it is altogether unlikely that, on the whole, the gains in the successful mining ventures suffice to offset the losses in the unsuccessful.

Jan 3, 1920

By Carel Robinson

MECHANIZATION of coal mine, is radically changing the requirements for under-ground transportation. It has increased materially the need for reliability and belt conveyors are the most dependable means of moving coal away from the place where it is mined. Their record of freedom from delays is almost 100 per cent. Why then are- not belt conveyors in more general use. Part of the answer lies in the pour records made at some of the earlier installations, and in the fact that belts have so long been identified as a type of equipment suitable, in the main, only to thin seams. Another reason is lack of knowledge of the full potentialities of belt transportation.

Jan 1, 1941

By S. H. Williston

IT is not often that bore hole surveys can be checked by actual civil engineering methods. A recent Arizona survey was checked by normal surveying methods and the comparison of the results should be of value to both oil and mining men. During the summer of 1948 the Phelps-Dodge Corporation, at its Copper Queen property near Bisbee, Ariz., drilled a 1245 ft, 8 in. diam, churn drill- hole in a mineralized area and cased part of it, intending to use it to transfer mill tailings for stope fill. The hole, as frequently occurs, was not straight, and, in endeavoring to locate the bottom in- the underground workings, they found no evidence of the hole at the underground coordinates directly below the surface location. The noise of the drilling tools was reasonably clear, but the direction of sound was uncertain. Preliminary tests with available equipment were not successful in locating the bottom of the hole. Be- cause of the mineralized character of the area and the fact there was some casing in the hole, any magnetic method of well surveying would give results ' of doubtful value.

Jan 1, 1950

By Victor O. Strobel

Fire-brick hot-blast stoves have been the subject of frequent discussions at the meetings of the Institute; and although it is my object to elucidate some of the points in connection with this subject, I will not go into the specific features of all types, but more especially call attention to a new type recently designed by Mr. Fred. W. Gordon. As the economical production of a ton of pig-iron is a more essential feature than a large output, much depends, where fuel cannot be obtained cheaply, upon suitable apparatus whereby high temperatures can be maintained. Where iron-pipe stoves have been employed, the fuel-consumption reached one and a half pounds of fuel, and, when a larger output was desired, often two pounds, to the pound of iron produced. The temperature attained rarely exceeded 900' F., and that at the expense of frequent renewals of the pipes, which was not inconsiderable. The fire-brick hot-blast stoves of the past five or six years have clearly demonstrated their superiority over the old system. Of the accompanying drawings, Fig. 3 illustrates a four-pass regen-

Jan 1, 1886

By Peter N. Blakey, Thiann R. Yu, Douglas O. Tansey

A flexible, efficient, and relatively low-cost drilling and blasting operation has evolved at Texasgulf Canada, Ltd.'s Kidd Creek underground mine. Located 32 km (20 miles) north of historic Timmins, Ontario, the underground operation utilizes a sublevel open stoping method developed with large-diameter blastholes. Over the years, Kidd Creek engineers have experimented with various drill-and-blast techniques, leading to the present-day practice. Continuing work is being conducted to further mechanize the blasting operation.

Jan 6, 1976

By T. A. Read, H. K. Birnbaum

STRESS-induced twin boundary motion in the AuCd ß'phase (52.5 at. pct Au 47.5 at. pct Cd having an orthorhombic structure (space group D h)' was discussed for the case of transformation twins.' Mechanical twinning, i.e., introduction of new twin orientations by the applied stress was sometimes observed in the ß' phase which contained two transformation twin orientations. (See Ref. 2 for experimental details.) The transformation twins terminated at the mechanical twin boundary; the two initial orientations having been twinned to the new orientation as shown in Fig. l. In a "hard" tensile instrument, formation of each mechanical twin was accompanied by a sharp drop in load (and an audible click) resulting in a typical serrated load-extension curve. The mechanical twins increased in width and additional twins were nucleated as the load increased until the entire specimen was occupied by the mechanical twin orientation. A restoring force2 caused the mechanical twin and transformation twin boundaries to return towards their initial configuration on releasing the load. In a stabilized specimen* the total strain introduced by mechanical twinning was recovered on releasing the applied stress. Initial and final microstructures were identical. After decreasing gradually to a critical width, mechanical twins suddenly disappeared accompanied by audible clicks and sharp increases in load (measured at a constant rate of crosshead motion in a "hard" machine). Mechanical twins could be stabilized in any position by maintaining the applied load for a sufficient time, indicating a decrease in restoring force with time similar to that observed for transformation twins.' Orientation relationships for mechanical and transformation twins were determined and are shown in Fig. 2. The mechanical twin, T3, was twin related to transformation twin, T,, by reflection in (1ll), and twin related to transformation twin, T2, by reflection in (111)T, . T, was related to T, by reflection in(ll1)T1 . The "average" mechanical twin composition plane lay several degrees from (1ll), . In every specimen which mechanically twinned, orientation T3 was most highly favored by the applied stress, i.e., it was the twin orientation which provided the greatest change in length compatible with the direction of applied stress

Jan 1, 1961

By T. W. Turk, S. A. Sass

The engineering design features of the Mercur Gold Project crushing, grinding, carbon-in-leach, bullion, reagent, and tailings disposal areas will be discussed in this paper. It presents a project overview and flowsheet along with selected design alternatives. During the engineering phase, major equipment and other features were selected to optimize design within site location and environmental constraints. The project team organization and procedures were adopted to accommodate multiple optimization studies while maintaining a tight engineering schedule.

Jan 1, 1985

By Wllliam D. Davis

C OMMERCIAL production of oil in northeastern Oklahoma began in 1897 and in the next two decades this area became one of the greatest oil districts of the time. Its importance is now secondary, but thousands of wells in this area have produced uninterruptedly for more than thirty years. They are now classified as stripper wells. By means of what is known as water flooding their L. production can be considerably in- creased. This practice consists in injecting water under pressure into the sand surrounding an oil well, thus displacing the oil in the pores of the sand and forcing it into the oil well.

Jan 1, 1940

By Robert H. Hafner, Irvin R. Kramer

IN recent years considerable interest has been shown in surface-alloyed metals, particularly those of chromium (chromized steels), which have excellent corrosion [ ] resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method1 employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high temperatures of 1200° to 1400°C. (2200° to 2550°°F,) caused excessive grain growth and warpage, Louenstein and Ulmer2 packed iron castings in ferrochromium and com- [ ] mon salt, and heated for approximately three hours at 930° to 1040°C. (1700° to 1900°F,). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900° to 1000°C., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a chromized layer, 0.004 in, thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1942

By Robert H. Hafner, Irvin R. Kramer

IN recent years considerable interest has been shown in surface-alloyed metals, particularly those of chromium (chromized steels), which have excellent corrosion [ ] resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method' employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high temperatures of 1200° to 1400°C. (2200° to 2550 F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- [ ] mon salt, and heated for approximately three hours at 930° to 1040°C. (1700° to 1900°F.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900° to 1000°C., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1942

By Charles Maier

IT has long been supposed that when crystalline materials are com-minuted the energy used in the production of increasingly smaller grain sizes is not entirely dissipated as heat but that a certain portion is "stored" as a part of the internal energy of the material. This portion usually has been called the "surface energy" of the particles. The practical interest of the Bureau of Mines in this subject in connection with the energy requirements of crushing processes has led to the author's attempt to measure the "stored" energy in finely divided calcite by heat-of-solution methods1. The experiments on calcite showed that "storage" of energy could not be proved for this material, because fine grinding caused a lack of chem-ical homogeneity evidenced by loss of carbon dioxide and subsequent adsorption of water on the surfaces of the calcite particles. When thermochemical correction was made for composition changes the cor-rected heat of solution was less for fine material than for coarse. Con-tinuation of the experimental work into the problem of comparing work and heat in the deformation of metallic crystals, where the calorimetric difficulties were less, showed, however, that in the case of copper and aluminum a real discrepancy between work and heat could be shown. similar results had previously been obtained by Farren and Taylor2 and Hort3 and more or less simultaneously with the author's work by

Jan 1, 1936