Search Documents

By J. C. Trantham, J. W. Marx

From 1955 to 1958 the Phillips Petroleum Co. conducted a series of small scale counterflow combustion field tests in a tar sand about 60-ft deep and 6 to 12-ft thick near Bellamy, Mo. A total of seven different well patterns, including conventional five-spots and seven-spots plus a 15-well line drive pattern and a 10-well radial pattern, were employed. Electric heaters, gas burners and wellbore fuel packs were tested as counterflow ignition devices. Direct drive ignition followed by reversal to counterflow operation was not possible in this case because of formation plugging by the semi-solid tar during the direct drive phase. Sustained counterflow burning was achieved with wellbore fuel packs under conirolled conditions which permitted close correlation of fire front velocity, air velocity, air-oil ratios and yields for a wide variation in process parameters. The tar in place was about 10' APl with a reservoir viscosity greater than 500,000 cp. The composite oil prodlcct was 26' API with a viscosity in the range of 5 to 15 cp. Vertical sweep efficiency in the line drive pattern was essentially 100 per cent, with no evidence of gravity segregation. Original tar in place ranged between 800 and 1,000 bbllacre-ft, specific rock permeability averaged about 800 md before burning and effective air pemeability with residual oil and water in place (at the time of ignition) averaged 250 md. The volume of oil recovered during stabilized line drive counterflow burning represented about 67 per cent of the volume of tar originally in place in the burned out zones. A minimum was found when air-oil ratios were plotted against formation air velocities, and a limiting air velocity existed below which the counterflow fire front reversed and burned back over its own trajectory, using the residual coke left behind. INTRODUCTION Early in 1955 the Phillips Petroleum Co. began preparations to field test counterflow underground combustion as a method for producing oil from high viscosity hydrocarbon deposits, such as bituminous (tar) sands. At that time all published information on the use of underground burning io increase oil recovery was based on the direct drive process, in which the fire front moved through the formatim in the same direction as the injected air stream. Such direct burning is not applicable to many heavy oil sands or to most tar sands because the heat-thinned native hydrocarbon congeals in the cold rock ahead of the fire front forming a gas permeability block which smothers the combustion. Laboratory experiments first demonstrated that this permeability blocking would not occur if the fire front and the air stream moved in opposite directions. In this counterflow (reverse) burning process the heated heavy oil or tar is driven back through the combustion zone. Here thermal cracking produces relatively light hydrocarbon products which pass through the heated rock behind the fire front (largely in the vapor phase) and are incapable of causing a gas permeability block.' Exploratory wring revealed that consolidated bituminous sandstones with a combination of tar saturation, permeability, thickness and depth favorable for experimental field testing existed at several points in western Missouri. By the fall of 1955, a test site for determining technical feasibility of the counterflow process under field conditions had been selected near Bellamy, Vernon County, Mo. — about fifty miles north of Joplin. The pay zone was too thin and too shallow to constitute a commercial prospect, but these same factors permitted controlled experimental operation with a small compressor installation and with a large number of monitor wells. These were needed for adequate observation of the underground phenomena at reasonable cost. RESERVOIR CHARACTERISTICS The reservoir chosen for the experimental field tests was a 124 thick section of tar sand extending from 49 to 61 ft subsurface, with shale and siltstone laminations sealing the top and bottom. This section was part of a larger 30-ft thick tar sand deposit which extended both above and below the test zone. Core analyses showed that the 12-ft sand was effectively subdivided into two approximately equal sections, with the lower zone being consistently more permeable than the upper zone. The most significant laboratory core data are summarized in Table 1. The line drive test which is the principal subject of this report utilized only the lower 6-ft thick zone, with the upper zone regarded as part of the 55-ft overburden. WELL PATTERNS The over-all field test program involved a total of seven different well patterns, including conventional five-spots and seven-spots plus a 15-well line drive pattern and a 10-well radial pattern. In some of the tests the full 12-ft zone was employed; in other cases only the more perme-

Jan 1, 1967

By Ernest Burchard

FLUORSPAR is found in most of the states from the Rocky Mountains westward, and commercial production of the mineral has been reported from Arizona, Colorado, Nevada, New Mexico, Utah and Washington. The map in Fig. 1 indicates the general distribution of many of these deposits but it is by no means complete. In the summer of 1926 the writer examined certain deposits of fluor-spar in Arizona, California, Colorado, New Mexico and Washington; in November, 1927, revisited the Jamestown, Colo., district, and in earlier years examined deposits in Colorado and New Mexico. Based on notes of his own and. on descriptions and other data by H. A. Aurand, H. W. Davis, R. B. Ladoo, V. C. Heikes, W. D. Johnston, Jr., and by producers of fluorspar, he prepared the following brief descriptions of deposits and estimates of reserves of fluorspar, originally for the use of the subcommittee on fluorspar of the Joint Committee on Foreign and Domestic Mining Policy and on Industrial Preparedness respectively of the Mining and Metallurgical Society of America and the American Institute of Mining and Metallurgical Engineers. Descriptions of many fluorspar deposits in various western states and districts have been published. It is not feasible to summarize this literature here, but the appended bibliography will indicate to the interested reader what papers are available.

Jan 1, 1933

By George M. Fowler, Joseph P. Lyden

PaGE Scope of this Report.................................................... 206 Production of Tri-State District.......................................... 207 Historical Sketch....................................................... 207 Location and Topography............................................... 211 Geology............................................................... 212 The Tri-State District.............................................. 214 Stratigraphy........................................................... 217 General Geological Section in Tri-State Region....................... 217 Stratigraphic Section of Mineralized part of Boone Formation........... 218 Stratigraphic Section Bird Dog Well.................................. 219 Metamorphism........................................................ 220 Structure............................................................. 225 Regional.......................................................... 225 Due to Metamorphism.............................................. 229 Ore Deposits.......................................................... 231 Types............................................................ 232 Hard-ground Deposits.......................................... 232 Brecciated................................................. 232 Stratified............................................ 232 Sheet Ground............................................. 232 In Dolomite............................................... 233 In Shale.................................................. 233 Soft-ground Deposits.......................................... 233 In the District as a Whole....................................... 233 Ore Minerah and Analysis......................................... 233 Paragenesis....................................................... 234 Conclusions........................................................... 236 Structure.......................................................... 236 Genesis of the Ore.................................................. 237 Future of the District............................................... 239 Acknowledgments..................................................... 239 Discussion............................................................ 239 Scope of This Report The Tri-State district. as outlined in this paper. refers to the entire mineralized area in sout'hwestern Missouri. southeastern Kansas and

Jan 1, 1932

By J. T. Eash, E. M. Wise

In a previous communication1 the improvement in slrength, harden-ability and color, occasioned by replacing gold in a typical gold-silver-copper alloy by various amounts of platinum, or palladium, was discussed. In the present paper the results of further studies upon the constitution and the nature of the hardening transformation in these alloys are presented. This research may be summarized as follows: 1. The liquidus and solidus have been determined for the alloys of the palladium and platinum series. Cooling curves were utilized for determining the liquidus of the palladium alloys but this method proved unsuitable for the platinum alloys so that a novel quenching method was utilized for the latter. Both the liquidus and solidus of the palladium alloys increase steadily with the palladium content. The liquidus of the platinum alloys increases rapidly with the platinum content, while the solidus temperature increases with the platinum content up to about 14 atomic per cent platinum, but suffers no further increase with additional increments of platinum up to 20 atomic per cent at least, owing to a peritectic reaction. 2. Palladium, and even more effectively platinum, reduces the rate of grain growth. Owing to this fact and to the increase in the solidus temperature, "overheating" does little or no damage to alloys containing reasonable quantities of these elements. This is confirmed both by tensile tests and metallographic examination. 3. The excess phase present in one of the high-platinum-content alloys has been isolated and chemically analyzed and was found to consist almost wholly of platinum, gold, and copper, evidently derived from the compound AuCu, by the partial replacement of gold by platinum. 4. The variation in the solubility of this platinum-content phase in the alpha solid solution with the temperature has been determined. This

Jan 1, 1933

Jan 1, 1957

By Howard Scott, Henry S. Rawdon

The method of demonstrating the structure existing in a metal or alloy at high temperatures, by etching a polished sample after it has been heated to the desired temperature, is quite familiar to metallog-raphists. The usual procedure1 2 is to heat the specimen, previously polished for microscopic examination, to the desired temperature, in a neutral atmosphere (hydrogen or nitrogen), then admit the etching gas (chlorine, hydrochloric acid or similar gas) for a few seconds, and finally, after flushing out the etching gas with the neutral one, cool the specimen in the neutral atmosphere. The pattern produced by etching at a definite temperature is usually taken as a record of the microstructure prevailing at that temperature. It has frequently been pointed out that changes in composition of the surface metal occur during the preliminary heating in the neutral atmosphere, so that the appearance produced by the etching at high temperature may not exactly represent the condition of the interior of the specimen. To overcome this uncertainty, the heating has sometimes been done in vacuo,3 the etching gas being admitted when the desired temperature was reached, then pumped out and the specimen cooled in vacuo. The studies of Rosenhain, Humfrey, and other workers 4, 5, 6, 7, 8 dem-

Jan 1, 1922

By Howard Scott, Henry S. Rawdon

The method of demonstrating the structure existing in a metal or alloy at high temperatures, by etching a polished sample after it has been heated to the desired temperature, is quite familiar to metallog-raphists. The usual procedure1 2 is to heat the specimen, previously polished for microscopic examination, to the desired temperature, in a neutral atmosphere (hydrogen or nitrogen), then admit the etching gas (chlorine, hydrochloric acid or similar gas) for a few seconds, and finally, after flushing out the etching gas with the neutral one, cool the specimen in the neutral atmosphere. The pattern produced by etching at a definite temperature is usually taken as a record of the microstructure prevailing at that temperature. It has frequently been pointed out that changes in composition of the surface metal occur during the preliminary heating in the neutral atmosphere, so that the appearance produced by the etching at high temperature may not exactly represent the condition of the interior of the specimen. To overcome this uncertainty, the heating has sometimes been done in vacuo,3 the etching gas being admitted when the desired temperature was reached, then pumped out and the specimen cooled in vacuo. The studies of Rosenhain, Humfrey, and other workers 4, 5, 6, 7, 8 dem-

Jan 1, 1922

By W. J. Keep

We have found that our graphic representations were, in some cases, not perfectly understood. In the tables by which we illustrate all our tests, the records appearing in the vertical columns between the rulings are the results of the tests of iron having the percentages and characteristics noted at the top of the column. The record is made by a short horizontal line in such vertical columns. It is located in horizontal spaces, which divide the table into units of measure, to indicate the value of the record. For example, in the upper part of Table VII. is recorded the transverse strength of the series of tests with white iron and aluminum, which were reported in our former paper. The numbers at the extreme top are the test-numbers. The fractional numbers below are the percentages

Jan 1, 1890

By J. M. Hassler

NOWHERE can there be found a more misleading statement than the old one that "Iron can be manufactured cheaper in the South." During the past decade ironmakers and users of iron have heard varied and sundry stories of the wonderful resources of the Birmingham district, including abundant ore and coal fields, cheap labor, a wonderful climate and similar industrial Utopian statements. Birmingham represents the major portion of the iron business in the South, acid as Birmingham fares so goes the iron business of the South. The intent of this paper is to shed some light on the actual conditions surrounding ironmaking in the South, especially in the Birmingham, or North Alabama, district. By a presentation of facts it is desired to point out that the "cheap iron" of the industrial South is a thing of the past, primarily because of increased labor cost and because labor is radically different in performance to what it was years ago. Also, because most of the raw materials needed in ironmaking that would be classed better than inferior are gone.

Jan 1, 1937

By R. D. Carnahan, G. A. Stone, R. J. Arsenault

An experimental technique has been developed for carrying out a dynamic tensile stress-strain test in which plastic strain is measured continuously throughout the microstrain region extending through the macroflow region to total deformations of 5 pet. The tests were carried out on niobium, samples having interstitial impurity levels of 160 and -800 ppm at temperatures ranging from room temperature down to 100°K. A band spectrum of activation energies was obtained from calculations based on the measured activation volumes and temperature dependence of flow stress. The inability of a single rate-controlling process to predict such a phenomenon has led to the proposal that several sequential rate-controlling dislocation mechanisms are operative in the preyield micro-strain region. These are thought to be: the motion of geometrical kinks, the formation of double kinks in edges, and finally in the macrostrain region the formation of double kinks in screws. In less pure niobium the effect of interstitial impurities is shown to be dominant in the microstrain region, suggesting that a fourth probable mechanism is overcoming interstitial barriers instead of geometrical kink motion and the formation of double kinks in edge dislocations. THE principal fundamental aim of most mechanical properties studies of crystalline solids is to determine the dislocation mechanisms responsible for the plastic behavior. The extension of such studies to the region of preyield microstrain behavior has received renewed attention in the past few years as the details of macroscopic flow behavior have become better understood. For the most part, microstrain studies have been carried out using one of two variations of a single experimental technique.1 The first method involves loading the sample at a constant extension rate to a predetermined stress level (less than the macroscopic yield stress), instantaneously unloading, and then determining the extent of plastic deformation to a sensitivity of 10"6. The microscopic stress-strain curve is then constructed from the results of a repeated series of such individual measurements, each of which involves loading to an incrementally higher stress level, by relating the accumulated plastic microstrain for each step to the maximum applied stress in that step. The second variation, also carried out by step-wise increases in stress, measures the total strain to a sensitivity of ~10"6 and relates the maximum stress to the area of closed hysteresis loops that are generated under certain conditions (namely, prestrained samples). The foregoing methods have yielded interesting information about the nature of preyield deformation and plastic response to stresses below the yield stress, but they offer certain disadvantages for studying the dynamic behavior of dislocations. In the first method it is physically impossible to specify a plastic strain rate inasmuch as the test sample is reexposed, as it is loaded to its maximum stress in a particular step, to lower stresses at which flow will take place. The strain corresponding to a given stress level on the stress-microstrain curve thus generated will then always be greater than that at the corresponding stress level of a truly dynamic test carried out at the same extension rate. The second method has been used to obtain correlations with dynamic macroscopic flow parameters by applying dislocation damping theory to the hysteresis loop areas.2 The approach has had some success but suffers in that only samples that have been prestrained a few percent can be studied. Although the stresses

Jan 1, 1968

By Walter Harvey Weed

Introductory.............449 Summary oF Types............452 I. The Virgilina Type...........452 The Virgilina mines...........452 Location.............452 History.............453 The rocks of the district..........453 The veins.............454 Notes on the mines.... 458 The Holloway. 458; Yancey and Durgy. 465 ; Copper World. 467 ; Frazier. 467 ; Thomas. 467 ; Anaconda. 468; Blue Wing. 468; High Hill. 472; Dorothy.......474 II. The Gold Hill Type...........474 The Gold Hill mine...........475 Location.............475 History............• 475 Surface improvements.......... 476 The rocks............478 Vein.phenomena...........478 Character of the ore..........481 Origin of the ore...........481 Notes on the mine.workings.........482 Other occurrences of ore-deposits of the Gold Hill type.. .. 483 III. The Ducktown Type..........484 The Ducktown mines...........485 Other examples of the Ducktown type....... 494 Alabama mines...........494 North Carolina examples : Ore Knob.......496 Virginia examples..........497 IV. The Catoctin Type.. ......... 498 General characteristics,......... 498 The Linden district...........499 General distribution of the Catoctin type.......503 Introductory. In the early history of this country the existence of copper in the Appalachian region was well known. but no mining mas attempted until the discovery of the Ducktown deposits in

Jan 1, 1901

By F. A. Crossley

The titanium-rich end of the Ti-A1 system has been investigated up to 35 at. pct A1 (23 wt pet). One conzpound Ti3Al was found to occur between primary a and TiAl. It is ordered hcp with DO19 structure, it has virtually no solid-solubility range, and it has a closed maximum at about 875°C. OIL either side of the compound are a +Ti3Al two-phase fields. The limiting a1uminum solubility in primary a at the titanium-rich end is indicated to be 7.5 at. pct A1 (4.4 wt pet) at 550°C and about 6.8 at. pct Al fl wt pct) at 500°C. Quenching alloys from above the a + Ti3Al two-phase field produces the following structures with respect to alloy composition: Up to 13 at. pct A1 (7.8 wt pet), a solid solution; from 15 to 18 at. pct A1 (9 to 11 wt pct), shear transformation product or martensite; from 19 to approximately 30 at. pct (11 to 19 wt pet), submicro-scopic coherent Ti3Al in an a malvix. The twin hcp phase fields reported in the literature are the result of nonequilibrium corzdztions. Ti-A1 alloys, once partitioned by dwelling- in the a + ß phase field during either hot working or heat treatment, are extremely difjicult to homogenize at temperatures below 1000°C. Such partitioned alloys exhibit the characteristics or symptoms of two-phase materials, and may be said to suffer the "twin-phase syndrome". THE earliest investigations of the Ti-A1 system by Ogden et al.1 and Bumps et al.2 reported wide solubility of the primary solid solutions. Aluminum was reported soluble in the low-temperature allomorph to the extent of 37 at. pct (25 wt pct), and the first intermediate phase was reportedly TiA1. Somewhat later Kornilov et al.3 reported a similar diagram with phase boundaries displaced towards lower aluminum contents and higher temperatures. Beginning about this time (1956) reports in the literature made it very clear that one or more intermediate phases occurred at lower aluminum contents than TiAl.4-17 These reports included five major investigations of the titanium-rich end of the Ti-A1 diagram.4,12,14,16,17 Three of these diagrams show two two-phase fields below 37 at. pct Al, while two of them show a single two-phase field. The existence of the phase Ti3A1 is firmly established and is included in each of the diagrams, except one—that of Sato and Huang.12 The new phases are reportedly hcp and differ from primary a only slightly when disordered, and when ordered the "a" parameter is approximately one,4,12,15 two, 6-10,13,14 or four14 times that for primary a. Beyond this, however, the diagrams are remarkable for their lack of agreement. Two tacit assumptions are usually made in phase-diagram determinations of metal systems. These are: 1) equilibrium anneals bring the alloy to equilibrium or to indistinguishable closeness to it, and 2) equilibrium conditions established at elevated temperatures are either "frozen" by rapid quenching for evaluation at room temperature, or quench-transformation products are recognized as such. In the current investigation evidence was obtained that over substantial composition ranges neither of these two conditions was met in any of the more recent major investigations. I) MATERIALS, METHODS, AND TECHNIQUES The alloys of this investigation were prepared by nonc on sum able electrode arc melting. Materials used in the preparation of the alloys are summarized in Table I. The investigative tools employed were: optical and electron microscopy, differential thermal analysis (DTA), disatometry, X-ray diffraction, electron diffraction, and resistometry. Alloys for microscopic and X-ray investigations were prepared as 15-g melts. Alloys containing from 7 through 11 at. pct A1 were hot-rolled out of a furnace at 900°C, from 12 through 15 at. pct out of a furnace at 1000°C, and from 16 through 18 at. pct out of a furnace at 1125°C. Alloys containing more than 18 at. pct A1 could not be hot-rolled. The ingots were covered with Markal coating prior to hot rolling to minimize atmospheric contamination. After hot rolling, alloys containing up to 15 at. pct A1 were ground and pickled to remove 7 mils from each surface; alloys containing 16 and 18 at. pct A1 were skinned to a

Jan 1, 1967

By Walter V. Knopp, Laurence Delisle

INTRODUCTION THE aim of this work was the preparation of nickel-steels from elemental metal powders by powder metallurgy techniques. It was known that plain carbon steels could be made from a mixture of iron powder and graphite and that the effect of carbon on iron in powder form was of the same nature as that produced in fusion metallurgy. The problem in making nickel steels from elemental powders consisted therefore in finding out whether sufficient diffusion of the nickel and other incidental metals normally present in such steels could be induced in the solid state to modify the properties of plain carbon steels made from powders and produce the beneficial effect of alloying. The composition selected originally was that of an S.A.E. 2330 steel. Metal powders, in the proportion corresponding to that composition, were mixed with graphite, pressed, and heated at different temperatures for different periods of time, to produce bonding of the metal particles and mutual diffusion of the various elements without melting. Temperatures up to 1325°C and sintering periods as long as 6 hr were first investigated because it was expected that such conditions would produce maximum diffusion with an accompanying improvement in the properties of the alloy. It was found that, although diffusion proceeded to a large extent under the conditions investigated, it would not be complete unless sintering were carried out at a high temperature for much longer than 6 hr. Relatively high temperatures and long sintering times are objectionable from a practical point of view, particularly when a low cost material is to be produced, because they necessitate the use of special, costly equipment. Work could be done to improve the diffusion of iron and nickel by changing conditions other than the sintering temperature and time, i.e., finer primary or alloy powders could be used. However, a marked change in the properties of the steel had been observed even with only partial diffusion. It was thought, therefore, that instead of trying to improve the diffusion, advantage might be taken of its incompleteness to produce a special structure consisting, in the unquenched condition, of a hard constituent, rich in nickel, dispersed in a tough pearlitic matrix. Steels with such a structure, not readily obtainable by fusion, should have desirable mechanical properties. Besides, it should be possible to prepare them from elemental powders under economical conditions. This latter alternative was therefore adopted for the second phase of this work. This report is divided into four parts: 1. General Procedure. 2. Effect of Sintering Temperature. 3. Effect of Varying the Nickel Content. 4. Effect of Alloying Elements. GENERAL PROCEDURE The general technique of cold pressing as used in powder metallurgy was applied.

Jan 1, 1948

By E. H. Bunce

CONTINUED progress in zinc metallurgy has been shown during 1933 by the adoption of new methods as well as the modernization of old processes and equipment, and by the initiation of new fields of activity for future advancement. The use of suspension roasting continued to grow as its advantages and adaptability became increasingly, apparent. The process developed by the National Smelting Co., Ltd., several years ago, of completely roasting on large sintering machines with utilization of the gas for acid manufacture has worked so successfully that an additional machine was installed during the year. At both the Swansea and the Avonmouth Works all of the ore for smelting is now roasted on the large sintering machines, thereby completely eliminating the old hearth-roasting furnaces. Work continued on obtaining partial purification of zinc ores from lead and cadmium by close control of conditions on the sintering machine, and in a few instances by chlorine additions to the ore before sintering. Ores so treated were either partially roasted or com-

Jan 1, 1934

By H. E. Gross

Recently, areas of abnormal rock pressure have been drilled on the Gulf Coast of the United States. These pressures may be caused by the recent and pronounced raising of some of the structures without loss of the formation pressure that existed when the reservoir was developing and the producing sand much more deeply buried. It is possible also that a permeable fissure may connect a shallow accumulation of gas with the gas cap of a much deeper reservoir of oil, gas and water. The pressures are so great that dependence on blowout-prevention equipment alone is hazardous to life and property. Fortunately, wells with excessive casing-head pressures, such as the Stanolind Oates No. 1 of the South Houston field, an 8700-ft. gas well with 6000 Ib. per sq. in., and the near-by Stanolind Candelari No. 1, and 8100-ft. gas well with 5000 Ib. per sq. in., have not blown out and cratered. A case is on record of drill pipe in a well in Harris County, Texas, (Oates No. 1) rotating for 8 hr. through blowout-prevention rams holding a back pressure of 2900 Ib. per sq. in. at the casinghead after the mud was altered by salt-water intrusion. Such conditions warrant the use of extremely heavy muds having low viscosity, made from galena (PbS) or specially prepared mixtures of hematite (Fe²O³) and galena suspended by bentonite. In some Gulf Coast wells, sodium silicate mixed with concentrated brine is used to drill through heaving shale formations. Such a fluid inhibits heaving remarkably, but it is expensive and costs as much as $10 per barrel. Barite has been used to weight this mixture. However, this mineral too rapidly increased an already excessive viscosity and it was thought that galena might be better for weighting such drilling fluid. The operator was anxious to try the latter, but none was available in the district. Laboratory Study of Heavy Muds To foster the use of the plentiful and extremely heavy mineral, galena, research has been done recently at the University of Oklahoma to determine the mud-making properties of this substance. For comparative

Jan 1, 1938

By John J. Cioston

THE steadily rising flood of gold production from all parts of the world has created an avalanche of rumors regarding the stability of the present price of this metal. Markets have been unsettled from Johannesburg to London from New York and Toronto to Melbourne, despite repeated denials from, American and British authorities of any immediate intention to alter the price. Various economists and financial writers have blossomed forth with predictions that the price would be set at the old level of $20.67 per oz.; some have even been so brash as to state That a price of $15 would be necessary to bring production within control. These effusions, based entirely upon monetary theories and with no regard to production costs, serve to confuse rather than clarify the situation.

Jan 1, 1937

By H. l. Burghoff, J. S. Porter

This paper presents the results of an investigation of the effect of cold-working and annealing treatments upon the occurrence of preferred orientation in annealed brass wire. The subject has received less consideration than has the same phenomenon in annealed brass sheet or strip, and perhaps very properly so in view of the obvious and undesired results obtained in the forming or drawing of strip having preferred orientation, which results are in contrast with the lack of any spectacular visual evidence in wire. The factors of cold-working and annealing that control preferredness in strip are naturally expected to function similarly in wire. Indeed, one might expect the condition to be commoner in annealed wire, because the severity of the cold-working between anneals in commercial Practice is usually much greater for wire than for strip. For example, a wire that is to be finished in the annealed condition on a diameter of 0.040 in. is commonly subjected to a final reduction of 90 per cent between the last two anneals, the large reduction being accomplished in the successive drafts of a multiple-die machine. Wire for rivets, for instance, on 0.125-in. diameter, although given a slight reduction of about Io per cent after the final anneal, may have been given a prior reduction of 75 to 80 per cent. Barrettl states the fiber axis of annealed 70-30 brass wire to be [111], with some indication of [IOO] as a secondary fiber axis. Croft and Sachs2 have reported briefly on some differences in brass wire with random and with preferred orientations. They showed statistical plots of the twin-band angles with respect to the wire axis or direction of drawing as observed on an axial plane. They also pointed out that the resistance of the wire to corrosion-cracking when externally stressed and exposed to a mercurous nitrate solution decreased as the degree of the preferred orientation increased. Material and PRocedure All the wire for the investigation was processed from one portion as cut for extrusion from a cast billet of the following analysis: 70.13 per cent copper; 0.01 lead; 0.01 iron; 0.02, nickel; 29.83 zinc (by difference). The billet section, 8 in, in diameter, was extruded hot to 3/4-in. diameter, after which it was processed by alternate cold-drawing and annealing treatments as indicated in Fig. I. The earliest anneals in process were at about 1100°F. and the next to the last reductions by drawing were 58 per cent. The diameter of the finally annealed wire was 0.132 in. Semifinal anneals were at 800°F., 950°F. and 1100°F. and reductions of 47.5, 74, 83.5 and 89.5 per cent were employed in drawing to 0.132 in. The final anneals were at 87s°F., 1050°F. and 1250°F. and were

Jan 1, 1944

By H. l. Burghoff, J. S. Porter

This paper presents the results of an investigation of the effect of cold-working and annealing treatments upon the occurrence of preferred orientation in annealed brass wire. The subject has received less consideration than has the same phenomenon in annealed brass sheet or strip, and perhaps very properly so in view of the obvious and undesired results obtained in the forming or drawing of strip having preferred orientation, which results are in contrast with the lack of any spectacular visual evidence in wire. The factors of cold-working and annealing that control preferredness in strip are naturally expected to function similarly in wire. Indeed, one might expect the condition to be commoner in annealed wire, because the severity of the cold-working between anneals in commercial Practice is usually much greater for wire than for strip. For example, a wire that is to be finished in the annealed condition on a diameter of 0.040 in. is commonly subjected to a final reduction of 90 per cent between the last two anneals, the large reduction being accomplished in the successive drafts of a multiple-die machine. Wire for rivets, for instance, on 0.125-in. diameter, although given a slight reduction of about Io per cent after the final anneal, may have been given a prior reduction of 75 to 80 per cent. Barrettl states the fiber axis of annealed 70-30 brass wire to be [111], with some indication of [IOO] as a secondary fiber axis. Croft and Sachs2 have reported briefly on some differences in brass wire with random and with preferred orientations. They showed statistical plots of the twin-band angles with respect to the wire axis or direction of drawing as observed on an axial plane. They also pointed out that the resistance of the wire to corrosion-cracking when externally stressed and exposed to a mercurous nitrate solution decreased as the degree of the preferred orientation increased. Material and PRocedure All the wire for the investigation was processed from one portion as cut for extrusion from a cast billet of the following analysis: 70.13 per cent copper; 0.01 lead; 0.01 iron; 0.02, nickel; 29.83 zinc (by difference). The billet section, 8 in, in diameter, was extruded hot to 3/4-in. diameter, after which it was processed by alternate cold-drawing and annealing treatments as indicated in Fig. I. The earliest anneals in process were at about 1100°F. and the next to the last reductions by drawing were 58 per cent. The diameter of the finally annealed wire was 0.132 in. Semifinal anneals were at 800°F., 950°F. and 1100°F. and reductions of 47.5, 74, 83.5 and 89.5 per cent were employed in drawing to 0.132 in. The final anneals were at 87s°F., 1050°F. and 1250°F. and were

Jan 1, 1944

By H. l. Burghoff, J. S. Porter

THIS paper presents the results of an investigation of the effect of cold-working and annealing treatments upon the occurrence of preferred orientation in annealed brass wire. The subject has received less consideration than has the same phenomenon in annealed brass sheet or strip, and perhaps very properly so in view of the obvious and undesired results obtained in the forming or drawing of strip having preferred orientation, which results are in contrast with the lack of any spectacular visual evidence in wire. The factors of cold-working and annealing that control preferredness in strip are naturally expected to function similarly in wire. Indeed, one might expect the condition to be commoner in annealed wire, because the severity of the cold-working between anneals in commercial practice is usually much greater for wire than for strip. For example, a wire that is to be finished in the annealed condition on a diameter of 0.040 in. is commonly subjected to a final reduction of 96 per cent between the last two anneals, the large reduction being accomplished in the successive drafts of a multiple-die machine. Wire for rivets, for instance, on 0.125-in. diameter, although given a slight reduction of about 10 per cent after the final anneal, may have been given a prior reduction of 75 to 80 per cent. Barrett1 states the fiber axis of annealed 70-30 brass wire to be [111] with some indication of [100] as a secondary fiber axis. Croft and Sachs2 have reported briefly on some differences in brass wire with random and with preferred orientations. They showed statistical plots of the twin-band angles with respect to the wire axis or direction of drawing as observed on an axial plane. They also pointed out that the resistance of the wire to corrosion-cracking when externally stressed and exposed to a mercurous nitrate solution decreased as the degree of the preferred orientation increased. MATERIAL AND PROCEDURE All the wire for the investigation was processed from one. portion as cut for extrusion from a cast billet of the following analysis: 70.13 per cent copper; 0.01 lead; 0.01 iron; 0.02 nickel; 29.83 zinc (by difference). The billet section, 8 in. in diameter, was extruded hot to 3/4 -in. diameter, after which it was processed by alternate cold-drawing and annealing treatments as indicated in Fig. I. The earliest anneals in process were at about 1100°F. and the next to the last reductions by drawing were 58 per cent. The diameter of the finally annealed wire was 0.132 in. Semifinal anneals were at 800°F., 950°F. and 1100°F. and reductions of 47.5, 74, 83.5 and 89.5 per cent were employed in drawing to 0.132 in. The final anneals were at 875°F., 1050°F. and 1250°F. and were

Jan 1, 1944

By R. P. Rothwell

Jan 1, 1885