Search Documents

By G. W. Preckshot, C. E. Cottrell, D. L. Katz, N. D. Delisle

Most crude oils contain asphaltic substances that may be naturally or artificially precipitated. In the Greeley field, California, this asphaltic bitumen is precipitated during the flow of the oil from the reservoir to the stock tank The mechanism of such precipitation is not well understood. This paper presents the progress that has been made by using the electron microscope as a new tool and by observing the effects of the streaming potential on the formation of bitumen particles. Crude oils at atmospheric pressure viewed in the electron microscope in very thin films under a vacuum showed no asphaltic particles. A technique of preparing slides of thin films by dilution of the oil with benzene and washing in petroleum ether was used at first, and these observations showed that the solvents caused the formation of the particles, varying from 0.01 to 0.2 micron in diameter. The electrical effects of fluids flowing through porous solid were studied, with emphasis on the formation of colloidal particles by the streaming potential. The streaming potential of crude oil flowing through sand was measured and was shown to be responsible for the formation of bitumen particles. These results bring out a new phenomenon, which may occur when crude oil flows through the porous oil reservoir. mechanisms. Asphalt has been the subject of widespread investigation but, owing to the complexity of the substances being considered, progress has been slow. Investigators working primarily with the asphaltic substances have treated the subject from the colloidal standpoint and have developed theories that picture the asphaltic particles as surrounded by adsorbed materia1s.14,15,17,24 The deasphaltization of lubricating oil by the use of solvents treats the subject primarily from the standpoint of liquid-liquid equilibria.'' A complete understanding of asphaltic substances would make possible the following of the material from its initial state in the crude oil through precipitation processes to the final plastic stage, the most common form of which is used in asphaltic pavements. Since these asphaltic particles are very small, it appears 'hat the electron microscope4 might be a useful tool in studying the precipitation processes. Specimens are examined by the electron microscope in a vacuum and as very thin films, requiring special techniques in preparation of samples. A brief description of the electron microscope and its operation will bring out the difficulties and advantages of its use for this problem. The first work was done with crude oils that had been diluted with solvents for the preparation of the film to be examined. Later a technique was developed by which the undiluted oil film could be made thin enough for direct examination. These two techniques show vastly different results Asphaltic particles have been precipitated from crude oils by a variety of

Jan 1, 1943

By Alfred R. Powell

LATE in 1944 a group of petroleum and coal technologists was organized in Wash¬ington under the sponsorship of the Petroleum Administration for War and the U. S. Bureau of Mines. This group, known as the Technical Oil Mission, was placed under the authority of the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff, which was then promoting the organization of other missions to be sent to Germany to obtain technical information regarding various industries in that country. The objective of the Technical Oil Mission was to obtain technical data on German production of synthetic oil from coal and all other commercial practices and research projects connected with the oil industry. The primary purpose was to obtain such data as were immediately essential to assist the war against Germany and Japan, with secondary emphasis on technical information that would assist American industry after the end of the war. Since oil-production facilities in Ger¬many and the occupied countries con¬trolled by Germany were the top targets for strategic bombing, the Technical Oil Mission was the first group under the Technical Industrial Intelligence Com¬mittee to enter Germany. A few members of the group flew to London in February 1945 and the majority of the remainder followed in March. In London they were joined by an equal number of British investigators and the combined, mission was then sent into Germany under the authority of the Combined Intelligence Objectives Subcommittee (CIOS). A sum¬mary of the more important information gained by this combined British and American mission is presented below. GERMAN OIL PRODUCTION The oil available to Germany, both natural and synthetic, and including pro¬duction from occupied countries, reached a peak in late 1943 and early 1944. Pro¬duction at this time was at the rate of 1,200,000 metric tons per month, equiva¬lent to i00,000,000 bbl. per year, or about 7 per cent of the wartime production in the United States. Of this production, 50 per cent was crude oil from Romania and Hungary, 12 per cent was crude oil from Germany itself, including Austria, 9 per cent com¬prised coal-carbonization products, that is, tar and light oil, and only the remaining 29 per cent was synthetic liquid fuel made from coal or tar. Synthetic liquid fuel made in Germany was equivalent therefore to less than 2 per cent of war¬time production of crude oil in the United States. The success of the strategic bombing campaign against German oil-production facilities is demonstrated by the fact that by September 1944 the Ploesti fields of Romania and much of the syn¬thetic oil production had been eliminated, so that the amount of oil available to the German war machine was only 25 per cent of the peak quantity mentioned above. By early 1945, when the combined British and American oil mission was entering

Jan 1, 1946

By A.J. PHILLIPS, Wm. B. Price

ADMIRALTY nickel is a new corrosion-resisting and heat-resisting white metal alloy composed of 70 per cent. copper, 29 per cent. nickel and 1 per cent. tin. It has been given the trade name "Adnic." In 1924, Win. B. Price1 described this alloy and its successful use as a diaphragm metal. The physical properties of Adnic at ordinary and elevated temperatures were given in Mining & Metallury.2 A patent3 was granted on Adnic, April 28, 1925. Work was first started on this alloy during December, 1921. An investigation of the patent situation in this country and abroad, and also a search of the literature, did not reveal any work on the ternary diagram, copper-nickel-tin; and the only wrought copper-nickel-tin alloy found was that known as "Newloy," composed of copper, 64 per cent.; nickel, 35 per cent.; tin, 1 per cent. This was being manufactured and sold by Wm.. Gallimore & Sons, Ltd., Sheffield, England, for unplated spoon and fork stock, and first came to our attention in January, 1922. The preliminary work in connection with the development of Adnic was started by casting four, binary copper-nickel alloys of the compositions shown in Table 1. Various amounts of tin were added to each of these mixtures, to produce the series of ternary copper-nickel-tin alloys also given in Table 1. A 200-gm. sample of each of these was cast by melting in a clay graphite crucible and allowing the melt to slowly cool with the furnace. A longitudinal section from each of these castings was polished and etched for-examination. The castings were not homogeneous solid solutions, but showed the usual cored structure associated with cast alloys. However, from an examination of these sections we roughly determined

Jan 1, 1928

By Ray Light, Everett M. White

Numerous articles have been written about the coal miner ; he has been compared with brave men who have gone out to conquer some unknown hazard throughout the ages. Now, however, modern mining is no longer something to be avoided, but a vocation that anyone can be proud of, with remuneration equal to or above that of almost any industry. A concerted effort is being made each day by both the operators of most mines as well as the state and federal inspectors to see that coal mines are as safe or safer than work places in any other industry. How- ever, it is true that mine fires and explosions have occurred in the mining industry since its inception. One of the earliest accurate references to such an occurrence is found in the transactions of the Royal Society of London. In the Colliery Managers' Handbook, 1898, Caleb Pamely writes of an explosion that occurred ,at Fatfield, England in August 1708, resulting in the deaths of 69 persons. He states: "Three of them, viz, two men and a woman, were blown quite up from the bottom of the shaft, fifty-seven fathoms deep, into the air, to a considerable distance from the mouth of the pit." It is interesting to note that women were employed ,as miners in England during that period. In the United States, the first record of coal mined was in 1702 by the Jamestown colonists. In 1786, about 20 years after Pittsburgh, PA was first settled, a charter was granted by William Penn to mine coal on the banks of the Monongahela River. Then in 1803, the first important coal company, the Lehigh Coal Co., was established. From this beginning, the mining industry continued to grow in importance and the first state mining law was formulated in 1870. The Pennsylvania state mining law was followed in 1873 by Ohio's, and in 1876 by Maryland's. A mine explosion at Avondale, PA in 1869 stimulated state legislatures to formulate these early laws. In 1907 near the town of Fairmont, WV, there were, within three days, two explosions resulting in a total of 597

Jan 1, 1981

By Edgar Bain

THE results are presented of an investigation to discover the fundamental atomic conditions existing in Corson's high-copper alloys hardenable by means of silicide solution and reprecipitation. The study attracted the writer because it offered a very convenient example of the general type of hardenable alloys exemplified by duralumin, Sykes' iron-tungsten and iron-molybdenum alloys and the hardenable lead antimony. SUMMARY OF RESULTS AND CONCLUSIONS In brief, the investigation shows that very perfect crystallinity exists in the solid solutions prepared at high temperature to contain as much dissolved silicide as possible. The lattice parameter of copper is altered very little by the amount of cobalt, nickel or chromium, and silicon dissolved. The hardening by drawing at a temperature to initiate precipitation of excess silicon and metal produces a remarkable change in the atomistics of the solid solution. The old perfection of crystallinity in the solid solution is destroyed and the new atomic spacings are of variable magnitude even in one grain, and a condition in a measure resembling that found in martensite is observed. Were no particles whatever precipitated by the drawing action, still ample causes for hardness would be in evidence in the solid solution alone. The lack of plane continuity in the crystal grains would oppose slip in a very effective manner. Complete annealing restores the crystalline perfection in large measure. In these alloys even the most sensitive methods failed to reveal the characteristic pattern of the silicide precipitated by the anneal, but this was largely to be expected as the amount is relatively small.

Jan 1, 1927

[ ]

Jan 1, 1938

By Ulick Evans

I SHOULD like to commence by saying how much I appreciate the honor which the American Institute of Mining and Metallurgical Engineers has done me in inviting me to visit your country, and to deliver this lecture before you. In choosing a subject, and in deciding what to include and what to omit, I have endeavored to discuss as far as possible work carried out recently in Europe with which you may not be unduly familiar. It would be poor return for your hospitality, and a mistaken sort of compliment indeed, if I were to load the lecture with accounts of researches carried out in your own country-researches with which you are probably better acquainted than I. Not that I have in any way excluded work done on this side of the Atlantic from my survey; one would indeed find it difficult to write on this, or on any other branch of science, without mentioning American work. But I have endeavored as far as possible to concentrate on aspects of the case which will, I hope, be comparatively fresh to you, and I feel fairly certain that this will be in accordance with your own wishes. If a strip of iron is heated strongly at one end, the other end remaining cold, there is produced over the heated portion a layer of oxide scale, the thickness of which diminishes steadily with the distance from the hot end. Somewhere in the middle of the strip, the thickness of the oxidized layer will become comparable to the wave length of light, and over this region the thin films give rise to a series of beautiful interference tints, commonly known as "temper colors." The colors are caused by the fact that two trains of light waves are reflected respectively from the outer and inner surfaces of the oxide film, and the possibility arises that the "crests" of one series of waves may coincide with the "troughs" of the other, thus diminishing the intensity of the light of some particular wave length. The state of affairs in this part of the strip is shown diagrammatically in Fig. 1, in which the film thickness is enormously exaggerated, of course, in comparison with the length of the strip; the

Jan 1, 1929

By E. H. Jr. Dix

DURING an investigation of high-strength manganese bronze by the Engineering Division of the Air Service, at McCook Field, Dayton, Ohio, particles of a "blue constituent" were noted in the microstructure of most of the bronzes examined. The constitution of the simple copper-zinc base alloy is still a matter of dispute in spite of the fact that the copper-zinc series is one of the oldest industrially important groups of alloys, and has received the early consideration of scientific research. The diagram, according to the most recent work,1 is shown in Fig. 1. The disputed questions involve the termination of the beta field and the line at 470° C. The earliest experimenter, Roberts-Austin, detected an arrest in some of his cooling curves at approximately this temperature and ascribed them to the formation of a eutectic; it has since been proved that there are no eutectics in this series. Shepherd2 was unable to detect any thermal arrests at this temperature; his diagram was essentially as shown in Fig. 1, except that the line at 470° C. was omitted and the beta phase carried down to normal temperatures. Later, Carpenter and Edwards,3 by a very painstaking research, definitely established the authenticity of the line but attributed it to the breakdown of the beta constituent into a eutectoid of alpha and gamma. Microscopic evidence of the formation of the eutectoid is doubtful and it seems more likely to be due to an allotropic change in the beta constituent as shown by Fig. 1. At least for practical purposes, it is more convenient to think of the structure of a 60-40 brass as a mixture of alpha and beta prime crystals rather than alpha plus an unresolvable eutectoid of "apparent beta" as it has often been called.

Jan 5, 1922

By Irving Hale

The superiority of electric power for mining purposes was recognized in a general way as soon as the electric motor be-

Jan 1, 1897

By Donald H. Beilstein

The St. Joe Minerals Corporation Lead Smelter and Refinery have been in continuous operation at Herculaneum, Missouri since 1892 as the Herculaneum Lead Smelting Division. Over the years, the plant has undergone many changes to increase production, improve the technology, reduce the cost of operations, and produce the highest grade of primary lead. The latest alterations were begun in 1950 and completed in 1970 and have resulted in the Herculaneum Smelter capacity being increased to in excess of 200,000 tons per year (180,000 metric tons). This increase has made the Herculaneum Smelter the largest in the United States, and second largest in the world. This paper will describe the Herculaneum Smelter equipment, processes, and material balances. Particular emphasis will be given to the McDowell-Wellman 10' x 100' (3 x 30 meter) up-draft sinter machine and ancillaries; to the new Heavy Smelting Department (blast furnaces and drossing section); to the new Lead Refinery and its automatic casting equipment and to the gas handling system including the 340 tons per day (305 metric) Sulfuric Acid Plant utilizing a -four pass converter. The description will include photographs, flow sheets, tonnages and assays where applicable.

Jan 1, 1970

By F. D. Rosenthal, F. J. Dunkerley, G. J. Mills

Activities, free energies, and heats and entropies of mixing of liquid Pb-Zn alloys have been obtained by the electrode-potential method between 400° and 650°C. The large positive deviations observed from Raoult's law are in agreement with the phase diagram, which indicates a wide immiscibility field. A vapor-pressure method was used to extend the activity measurements to 900°C, allowing the maximum of the immiscibility gap to be estimated by thermodynamic calculation. Data on the mono-tectic and eutectic points compare favorably with previously existing work. SEVERAL long-standing methods have been in use for the study of phase diagrams from measurement of the activities of the component metals.' The use of thermodynamic analysis for interpreting equilibria data is comparatively recent, however. Such analysis is usually undertaken by first evaluating the principal thermodynamic functions as, for example, the enthalpy, entropy, and free energy of the alloy constituents. These, in turn, quite often can be correlated with the interatomic potential energies and atomistics of the system, from which a clearer understanding of the causes leading to deviations from ideal behavior is gained. The present study of liquid Pb-Zn alloys is concerned with a determination of these quantities by electrode-potential and vapor-pressure measurements, using these values in calculations involving phase equilibria and to obtain a theoretical insight into an alloy system exhibiting strong positive deviations from ideal metallic solution. A considerable portion of the previously reported work is based on thermal analysis. Supplemented by optical studies of solid alloys, these techniques have revealed the essential nature of the immiscible mixtures that are formed. It is difficult, however, using the phase-

Jan 1, 1959

By W. A. Alexander, L. M. Pidgeon

Metallic magnesium and similar meta!s near the top of the electromotive series have been commercially produced by the electrolysis of a suitable molten salt. Despite the success of electrolysis, sufficient inherent objections exist to justify the search for a direct reduction method. Such a method would widen the choice of raw materials, relax the rigid electrolytic requirements of raw-material purity, and, by obviating direct current, over simplicity of plant equipment. This paper describes the pilot-plant development of one such method, which has subsequently formed the basis of operation of six commercial plants-—one in Canada and five in the United States. Unlike aluminum, magnesium is volatile at relatively low temperatures. This physical property, which produces its greater inflammability, also offers possibilities of direct reduction that are not available with aluminum. In the basic reaction MgO + X = XO + Mg if X is nonvolatile, the reaction may be forced to the right at high temperatures by the evolution of magnesium vapor, despite the large negative value of the heat of reaction which is almost bound to follow the use of any available commercial reducing agent. The cheapest X, of course, is carbon, but this notable advantage is modified by the production of a volatile oxide CO, so that both Mg and CO are evolved simultaneously. Elaborate devices are required to shock-cool the equilibrium mixture in order to prevent back reaction. At best, a pyrophoric powder is produced, requiring redistillation to provide marketable metal. The practical development of this process, is due to F. Hansgirg, and his methods have recently been given a trial on a grand scale in the plant at Permanente, California, and smaller plants were previously built in Austria, England and Japan. A second class of reducing agents is available, those which produce nonvolatile oxides. When XO and X are relatively nonvolatile, magnesium is the only volatile member of the system. It may be evolved in a simple distillation step and condensed without the formation of powder. Two basic requirements must bc fulfilled in order that such a reaction may proceed: I. The reducing agent when heated to a reasonable temperature in presence of MgO must cause the production of an appreciable equilibrium vapor pressure of magnesium. This magnesium must be removed continuously. z. A supply of heat must be maintained. In order to fulfill the first requirement, operations must be conducted in vacuo or in a stream of Hz. Owing to its greater efficacy and relative safety, vacuum has been employed in the work to be described. The choice of a suitable reducing agent formed the subject of an extensive series

Jan 1, 1944

By Hewitt Wilson

IN 1903, T. M. and E. H. Alvord, of Marblemount, Wash., built a soapstone-grinding mill in the Skagit River Valley and are reported to have produced "ground talc" during 1904 and 1905, shipping to the paper mills in Wisconsin. Between 1916 and 1920, the Western Talc Co. built and operated a talc-grinding mill north of Mondovi, on the banks of the Spokane River, in eastern Washington, and sold powdered talc to the Inland Empire Paper Co. of Spokane. ? The most active develop-ment in recent years has been by two companies in the Skagit Valley-the Skagit Talc Company, Inc., which has been sawing soapstone block for the soda-recovery furnaces of the pulp and paper companies, and the Asbestos-Talc Products of Washington, Inc., at Burlington, which has been mining and dry-grinding a soft serpentine for the structural filler and insulation trade. Many prospects have been opened in the northern part of the state on both sides of the Cascade Mountains, and these activities undoubtedly are the forerunner of an industry that promises to attain considerable magnitude in the North Pacific States. At the present time, talc is imported from California for use as paper filler, and soapstone block from Virginia for use in the soda-recovery furnaces. A small market has been created locally for tailor and foundry:, pencils, stove grills, and block soapstone for art objects. The results of the present study, as yet incomplete, indicate that the use as a refractory and as a ceramic filler and flux can be expanded.

Jan 1, 1936

By Herbert Hoover

THE desire of the engineers over the last few years, growing out of their contact with public affairs, that this Institute should take a wider vision than the narrower field of technology and should apply its skill to the development of civic problems which must lay in their foundation on engineering, has led to this discussion today. Some of us in San Francisco, in discussing this question of the relation of the engineers to civic problems, raised the question as to whether or not in this national emergency it was not the duty of the Mining Engineers to bring, forward their combined skill and knowledge and experience to bear upon the problems of the coal industry. This industry, considered as a whole, is one of the worst functioning industries in the United States. It is equipped with capital, with machinery, plants and labor to a peak load at least 20 per cent. above the average necessity. This peak load, therefore, involves the use of probably 100,000 men diverted from other productive industries; it involves an intermittency of employment through its whole personnel that results not only in a long train of human woe, but results also in a higher cost of coal -to the general public. The problem of whether the industry can, by any device, be cured or even partially cured of its intermittency, is solely an engineering problem. It is therefore an apropos problem for this Institute. Your President and myself and others thought that we could best develop this discussion by calling upon men of large experience in the particular branches of the soft coal industry, to bring the facts in front of this general committee, with a view to an exhaustive discussion and perhaps subsequently the appointment of a committee to formulate those facts and such remedies as may be developed into a report that would be of constructive value.

Jan 3, 1920

By C. E. Lundin, M. Hansen, D. J. McPherson

PRIOR work on the Zr-Cu phase diagram by Alli-bone and Sykes,' Pogodin, Shumova, and KUGU cheva,' and Raub and EngeL3 as confined largely to copper-rich alloys. The investigations of Raub and Engel were the most recent and seemingly the most complete of these. Alloys from 0 to 68.3 pct Zr were studied principally by thermal analysis and microscopic examination. These authors reported an inter metallic compound ZrCu, (1116°C melting point) and two eutectics, one at 86.3 pct Cu (977°C mp) and the other at 49 pct Cu (877°C mp). The solubility of zirconium in copper was reported to be less than 0.1 pct at 940°C. The zirconium melting stock consisted of Westing-house "Grade 3" iodide crystal bar (nominally 99.8 pct pure). It was treated by sand blasting and pickling (HF-HNO, solution) to remove the surface film of corrosion product, resulting from grade designation tests. The crystal bar was cold rolled to strip, lightly pickled again, and cut into pieces approximately 1/32 in. thick and 1/4 in. square. These were cleaned in acetone, dried, and stored for charging. The high-purity copper (spectrographic grade) was supplied by the American Smelting and Refining Co. with a nominal purity of 99.99 pct. These copper rods were rolled to strip, cut into squares the same size as the zirconium platelets, cleaned in acetone, dried, and stored. Equipment and Procedures The equipment used for melting and annealing the zirconium binary alloys and for the determination of solidus curves has been described in connection with previous work on the Ti-Si system' and in recent papers in this series describing the studies on eight binary zirconium systems.5-' Techniques employed for preparing and processing the alloys were also similar to those used in the above references. Ingots of 20 g were melted under a protective atmosphere of helium on water-cooled copper blocks in a nonconsumable electrode (tungsten) arc furnace. The ingots were homogenized and cold-worked prior to isothermal annealing to aid in the attainment of equilibrium. The specimens were heat-treated in Vycor bulbs sealed in vacuo or under argon, depending on the temperature of the anneal. Quenching was accomplished by breaking the Vycor bulbs under cold water. Temperature control was within ±3OC of reported temperatures. Thermal analysis was primarily relied on to determine eutectic levels, peritectic levels, and compound melting points. The induction furnace incipient melting technique was also used but did not provide the accuracy obtained by thermal analysis in this system, which involves much lower solidus temperatures than the other zirconium systems. A special technique for the determination of characteristic temperatures was employed in the case of several intermediate phases and their eutectics which displayed very small differences in melting temperatures. Specimens were sealed in Vycor bulbs and annealed at a series of very accurately controlled temperatures. Metallographic examination was then employed to reveal incipient melting. Furnaces and techniques in general were described previously.' The echant used was 20 pct HF plus 20 pct HNO3 in glycerine unless otherwise stated. Results and Discussion The chemical analyses of the majority of alloys prepared for the determination of phase relationships in this system are given in Table I and a brief summary of the equilibrium anneals employed is given in Table 11. In a preliminary program, alloys containing 1, 4, and 7 pct Cu were annealed for three different times at each of the temperatures 700°, 800°, and 900°C. No change in the relative amounts of phases present was detected after 350, 150, and 75 hr at the above temperatures, respectively. The times listed in Table II were accordingly chosen as a result of these preliminary tests. Zirconium-rich alloys containing from 0.1 to 10 pct CU were reduced by cold pressing from 58 to 8 pct, depending upon thk alloy content, homogenized for 7 hr at 900°C, and then reduced 80 to 13 pct by cold rolling, again depending upon copper content. Other alloys were studied in the cast, or cast and annealed conditions. The contracted scope of investigation for this system included the range 0 to 50 atomic pct Cu. This approximate region is shown in Fig. 1. Due to evidence of phase relationships departing considerably from those proposed by Raub and Engel" in the 50 to 100 atomic pct range, the investigation was extended to cover this composition area rather thoroughly also. Fig. 2 is a drawing of the entire diagram. The labeling of some phase fields was omitted in Fig. 2 for the sake of clarity. An expanded view of the zirconium-rich region, with the experimental points necessary for its construction, is given in Fig. 3. The generally accepted value of Vogel and Tonn8 or the allotropic transformation a + 862' ±5OC, was employed in the construction of these diagrams. A careful study revealed that the "Grade 3" crystal bar used in this investigation actually transforms over the approximate range 850" to 870°C, due to impurities. It must be expected that this two-phase field in unalloyed zirconium will cause some departures from binary ideality in the very dilute alloys. Zirconium-rich Alloys: The a + ß transformation temperature is decreased from 862" to about 822°C by increasing amounts of copper. Thus, a eutectoid reaction, fi ß a+ Zr,Cu, occurs at a composition of about 1.6 pct Cu. The eutectoid level was determined to lie between the alloy series annealed at 815" and 830°C. The placement of this eutectoid temperature

Jan 1, 1954

By Charles H. Fulton

Experimental work on the process was begun on a laboratory scale at Cleveland, Ohio, in 1914, and transferred to East St. Louis, Ill. in 1916, where a commercial sized furnace was in technical operation until January, 1918. The essential steps of the process are as follows: Oxidized zinc ore or roasted zinc concentrate is mixed with crushed coke and coal-tar pitch and formed into briquets 9.25 in. (23.5 cm.) in diameter and 21 in. (53 cm.) long in a manner similar to that used in the manufacture of graphite or carbon electrodes, except that much less care and time are required. The composition varies with the nature of the ore; in one case, the composition was 100 parts ore, 70 parts coke, and 18 to 20 parts pitch. These briquets maintain their form and volume during and after the distillation of the zinc. This object is gained by using coke as the matrix and coal-tar pitch as the binder; this pitch becomes coke on heating and unites the ore particle and the original coke particle into a continuous mass. The briquet is an electrical conductor but only to such a degree that it can be used as a resistor. The size of the ore, as in the present practice of zinc metallurgy, ranges from fine material, such as flotation concentrate, to coarse table and fine jig concentrate. The process is not restricted to any particular kind of ore, but is applicable to pure high-grade ores, ores high in iron, and complex zinc-lead ores, since the residue from the distillation IS held immovably in place within the briquet. In the case of complex zinc-lead ores, the distillation is conducted with a carefully regulated temperature so that a high percentage of lead is retained in the distilled briquet, which may then be smelted for its lead content. In present zinc smelting practice, the reduction fuel is from 40 to 50 per cent. of the weight of the ore. In the briquet, it is from 60 to 85 per cent. of the ore; but unless the ore is exceptionally high in residue, the distilled briquet may be used over again as coke, or as a high ash coke for fuel purposes in power production. Baked briquets are hard and tough and may be handled roughly

Jan 1, 1921

By R. E. Cech

Particles -3 to 30 µ diam of a 29.5 pet Ni, 70.5 pet Fe alloy after being melted and solidified while falling through a hydrogen atmosphere were found to contain a distortion-free body-centered-cubic phase. In most particles, the amount of body-centered-cubic phase approaches or equals 100 pet. It was shown by a series of experiments that this phase forms directly from the liquid. It is pointed out that a mechanism previously suggested in recent papers on the theory of the liquid-solid transformation can account for the solidification of body-centered-cubic phase in a temperature range where face-centered-cubic is the stable phase. IN the course of an operation to produce powders for a study of the martensitic transformation in Fe-Ni alloys, an unexpected phenomenon was observed. Powders of a 29.5 pet Ni alloy, which has a subzero M, temperature, were found to contain considerable amounts of a body-centered-cubic phase at room temperature. The experiments to be described were designed to elucidate the mode of formation of this unexpected phase. Experiments and Discussion An alloy containing 29.5 wt pet Ni, balance iron, was vacuum melted from high purity electrolytic iron and carbonyl nickel shot and solidified in the crucible. The metal was converted to oxide, ground to 100 pet <37µ, pressed to a cake, and homogenized 20 hr at 1350°C. To insure homogeneity the grinding, pressing, and homogenizing heat treatment was repeated a second time. The oxide was then ground to 100 pct <37µ and hydrogen reduced at 500°C. The reduced powder was given a spheroidizing treatment to produce spherical cast particles. The treatment consisted of dispersing the particles in hydrogen and allowing them to drop through a vertical hydrogen furnace set to a temperature higher than the liquidus of the alloy. This operation, commonly known as shotting, has been described more fully elsewhere.&apos; The powder produced by this method was found to contain approximately equal parts of body-centered-cubic and face-centered-cubic phases. A magnetic separation technique, previously described,&apos; was applied, and it was found that particles were either completely face-centered-cubic or nearly completely body-centered-cubic. The microstruc-

Jan 1, 1957

By Lester A. Blackner

The Ray Consolidated Copper Co.&apos;s mining property is located on Mineral Creek, 6 miles north of Kelvin, at Ray, Pinal County, Ariz. (Fig. 1). The mining claims now owned by the company consist of 126 lode claims, comprising 2,144.9 acres, containing at the beginning of operations 82,904,368 tons of 2.19 per cent. copper ore. General Characteristics of the Orebody The main orebody is a disseminated deposit in schist and porphyry formed by secondary enrichment. Its existence was proved by churn drilling, and it is at present one of the largest proved copper deposits in the world. The orebody itself covers 205 acres with an average thickness of 121 ft., and occupies a definite belt which has a northwest direction. Its length is approximately 5,000 ft. The width varies, being about 2,000 ft. at the west end and 2,500 ft. at the east, narrowing down irregularly from both ends to a few feet in the center. The thickness of the body varies greatly along the line of lode, ranging from a few feet up to 470 ft. thick. The ore horizon is not constant, but varies, following in a broad sense the topography. The body in general dips slightly to the northeast, and is broken up by numerous small faults and fractures. The ore-bearing formations, consisting of mineralized schist and mineralized granite porphyry, stand fairly well and offer no difficulty in mining operations. The bulk of the ore is chalcocite disseminated in schist. In places cupriferous pyrite is closely associated with the chalcocite. The mineralized gr&apos;anite-porphyry forhations are contiguous to the ore-bearing schist. • Overlying the orebody is an oxidized zone of leached iron-stained schist, averaging 252 ft. in thickness, termed "capping." The Line of

Jan 1, 1916

By E. L. Anders

The Mile Six pool is located on the La Brea-Parinas Cullcession of International Petroleum Co., Ltd., in northwestern Peru on the west coast of South America. The reservoir pressure in this pool has been maintained within 200 psi of its initial value throughout its history, and gravity drainage has played an important role in the production behavior. It has now produced 95 per cent of its estimated ultimate recovery. It is estimated that this interesting oil pool will ultimately produce 67 per cent of the initial oil in place and that the resulting residual oil saturation may be as low as 19 per cent of the pore volume (29 per cent of the hydrocarbon pore volume). An evaluation of reservoir rock and fluid characteristics and ultimate oil recovery is presented. INTRODUCTION This study of Mile Six pool was made to evaluate its performance according to latest available information. The production performance of this pool has been discussed in various articles in the past. and the reported behavior has been used as an example for application of computation procedures for gravity drainage depletion&apos; and as an illustration of field behavior under gravity drainage or expanding gas cap drive. There have been wide variations in reported values of initial oil in place, reservoir oil volume factor. connate-water sauration, volume of effective sand, and ultimate recovery because of the paucity of reliable basic data. These various factors have been determined as accurately as practicable with the latest available information, and this evaluation is presented herein. The production history of Mile Six is an excellent example of gravity drainage depleion with effective pressure maintenance by gar injection. GENERAL Mile Six pool was discovered by cable-tool drilling in November. 1927. when well 1996 was completed in the Parinas sand. After slow development with cable tools and sporadic production. the pool was opened to continuous pro(iuction in November. 1933. and develpment was completed with rotary rigs. Pressure maintenance was started in December, 1933. by returning gas to upstructure wells. Most of the development was &apos;completed by 1937, but some additional wells were drilled in the period 1939-1947. and several old wells were deepened. A total of 46 oil and gas wells and 4 dry holes were drilled on approximately 7-acre spacing. Of the producers. 21 are now flowing. 2 are pumping. 44 are gas input wells. 3 are abandoned. I is a gas well shut in. and 15 are shut in because of non-commercial production or high gas-oil ratio. The locations of all wells are shown on the map of Fig. I. Total oil production on Dec. 31. 1952, was 30,867,373 bbl: cumulative gas production was 22,023,777 Mcf; and 26,410,946 Mcf of gas had been returned to the reservoir. These figures do not include oil and gas lost ill a blowout in January. 1940. GEOLOGICAL DESCRIPTION Mile Six pool is located on the northern end of a structural spur projecting from the La Brea-Negritos uplift.&apos; The spur is probably a reflection of a basement structure. It plunges gently to the north, i broken into a complex series of fault blocks. and contain.; the Verdun Alto. Section Sixteen. and Mile Six pools. The Parinas handstone (lower Eocene!. which is the producing formation in Mile Six. occurs at an average depth of 2,200 ft in the pool and dips north and east at from 15&apos; to 20". The pool covers an area of approximately 350 acres. Mile Six is downfaulted about 600 ft from Section Sixteen pool to the soutb. and a major fault forms its western boundarv. The north and east boundaries are formed by the intersection of the sand top with the water-oil contact which occurs at approximately 2.440 ft subsea. An original gas-oil contact probably existed at about 1.875 ft subsea. Fig. 1 presents the latest structural interpretation of the pool. and Fig. 2 is an isopach map showing thickness of the total Parinas formation above the original water-oil contact. The heavy lints of Fig. 1 are contours on the sand top, and the fine lines are contours on the fault planes. This type of straight-line structural map was developed 1)) International&apos;s geologists to reflect structural conditions where the bedding planes dip and have no curvature. &apos;The La Brea-Parinas Concession is highly faulted by normal fault.. The beds are flat wherever exposed. The Parinas formation is approximately 635 ft thick. and it is etimated that 62 percent II the formation is effective sand. The original oil zone was about 565 ft thick. Fig. 211 presents an electric log showing typical Parinas sand development ill Mile Six pool. The Parinas band in Mile Six i. a well-sorted. medium- to-coal-se-grained. cross-bedded sand with minor lenses of shale and small lenses and pockets of pebble conglomerate. The sand grains are subangular to rounded and consist chiefly of quartz with feldspars. biotite hornblende, and augite as accessory minerals. Because of faulting of the Parinas- formation to the east and north of the pool. there is probably l possibility of a significant, natural water drive in Mile six. The faults within the pool. as indicated in Figs. 1 and 2. are of smaller disI,laceInent and seem to act only , partial barriers to fluid movement within the reservoir. RESERVOIR CHARACTERISTICS Core analysis data are available from five wells. The data were obtained from three wells (Nos. 3401. 3586 and 3719) at the time of their completion and from well 1996 when the original liner was sidetracked and the well was deepened ill 1946. Data from well 2779 were obtained in 1943 from old cores taken when the well was deepened in 1934. From these core analyses. the average porosity was estimated to be 22.6 per cent. and the average permeability to dry ail. was estimated to be 780 and Measured productility indices varied from 3.1 to 71.4 B/D per psi differential. Specific productivity indices varied approximately from 0.1 to 0.3 B./D per psi per ft of sand.

Jan 1, 1953

By J. J. Lander, L. H. Germer

MOLYBDENUM and tungsten have desirable corrosion and temperature resistant properties, but the metals in bulk are expensive and their fabrication is difficult. Such considerations led to a search for a method of plating them upon base metals. This search was successful and led furthermore to a number of developments which could not have been foreseen. Neither pure tungsten nor pure molybdenum has been electroplated successfully, although the literature of electroplating is liberally sprinkled with the description of unsuccessful attempts. The process of plating these metals by thermal reduction of their halides has achieved only limited usefulness because of technical limitations and because of limited range of product quality. Plating by thermal decomposition of the carbonyls does not suffer from limitations of the same sort and the properties of the plate are readily controllable. This paper describes the plating of molybdenum and tungsten, and of compounds and alloys of these metals, by pyrolysis of their carbonyl vapors. Chromium also has been plated in this manner, but the experiments upon chromium have been less extensive and the results much less satisfactory. Probably the most important of the products which we have obtained are the alloys with carbon, and the carbides of the metals. Either molybdenum or tungsten can be deposited upon a base metal as a coherent and adherent coating. By adjusting the plating condition the carbon content of the coating can be made to have any value from substantially zero to about 35 atomic pct. The hardness is dependent primarily upon the amount of carbon in the plate and can be regulated over a very wide range, some coatings containing considerable carbon being harder than sapphire. In addition to products already known this method of plating has yielded new carbides of molybdenum and tungsten and alloys supersaturated with carbon. These new products are possible because, in the process of plating, carbonyl can be decomposed at temperatures as low as about 150&apos;C, and thus in the presence of other substances reactions occur which could perhaps not be produced in any other way. In addition to carbides and alloys with carbon, sulphides and oxides of molybdenum and tungsten have been produced and studied. There are certain other advantages of the carbonyl method of plating. It is not required that the base have good electrical conductivity as in electrochemical processes, and the base need not have the temperature stability required in plating from a halide. Thus low melting glasses, as well as other ceramics, can be plated almost as readily as metals. In particular, the plating of glass with

Jan 1, 1947