Search Documents

By Leonardo Camilo dos Reis, Edmilson Fernandes Dadomi, Claudio Silva de Paulo

In the hot strip mill production, one of the factors that may affect the productivity is the occurrence of failure due to the geometry of the strip at the exit of the rolling mill, because the tip of the strip can turn-down or turn-up. This study had the objective of evaluating the behavior of the strip when leaving the working rolls, through numerical simulation, aiming to know the influences of the main variables that govern the formation of the turn-down. The methodology consisted in performing the computational simulation of the strip mill and to vary the operational and geometric parameters that could influence the process. The results showed that the rolling of hot strips of HSLA material with final thickness varying between of 3 to 6 mm and a reduction of 6.6% to 11.0% in the last stand of a hot strip mill, tends to bend towards the roll with larger diameter, higher friction coefficient , higher temperature and lower limit of material flow. It was observed that the variation in diameter is the main factor that contributes to the formation of the curvature of the front-end of strip. Based on these results, several measures were implemented in the industrial line, with a significant reduction in the occurrence of turn-down.

Oct 2, 2019

By Gerhard Finstermann, Ichiro Maeno, Takehiko Saito, Hironori Shimogama, Konrad Krimpelstätter

Automobile manufacturers are developing Electrified Vehicles with light steel body structure designs that reduce mass and therefore greenhouse gas emissions over the vehicle’s entire life cycle. This raises the demand for the production and development of Advanced and Ultra High-Strength Steels (AHSS / UHSS) and Electrical Steels with increased permeability and reduced core loss to improve energy conversion efficiency. To meet this requirements the steel market is tending towards new generations of AHSS with improved formability (3rd generation AHSS) and high-silicon steels with higher strength and thinner products. With this growing demand for advanced high-strength steels and electrical steels, producers are faced with a unique and interesting challenge in producing materials that strain or exceed the capabilities of existing mill equipment and automation designed to produce low- to medium-carbon sheet. While specialty steel producers have known for decades how to process special high-strength steels and thinner gauges, this equipment typically does not offer the yield and productivity desired by the market, necessitating innovation in re-engineering existing equipment to meet the market demands more economically than new construction. In the case of cold rolling, this can be supported through variable roll geometries, more effective roll-gap lubrication technologies, application of strip heaters (Warm Rolling) to reduce risk for edge crack propagation and strip breaks as well as continuous rolling managed by state-of-the-art automation technologies.

Oct 1, 2019

By Jeremy Fletcher

In today’s world, the requirement of Steel Producers to revamp and modernize their blast furnaces on-time, safely and with the latest technology is paramount. In addition they must meet the detailed design, construction and safety legislation and regulations, which can be different for the various countries around the world. Siemens MT is renowned for its ability to perform Blast Furnace rebuilds, relines and modernisations within extremely tight time frames and in a safe manner. Modular Blast Furnace construction concepts have been perfected to minimise project duration and plant downtime for furnace rebuilds. Safety and certainty are the keys for success. Siemens MT are constantly introducing new technologies into the market place including cyclone gas cleaning and triple external cone gas scrubber, along with step changes in technology such as dry gas cleaning and dry slag granulation. The economic environment and the continuing requirement for improved environmental performance, drive many of these innovations. This paper describes some of the latest rebuild reference projects of Siemens MT, along with the latest technical innovations installed on these furnaces, and some of the construction methodology used for a safe and secure rebuild.

Aug 1, 2018

By Kazuya Nakabo

In this article, influences of restraint and MgO content on densification of alumina-magnesia castable during heating were experimentally studied. High thermal expansion-alumina-magnesia castable specimens were surrounded by low thermal expansion-alumina-silica castables, and heated in an electric furnace. Doing so allows restrained heating of alumina-magnesia castable. According to the results of simple calculations, the restraint stresses were estimated to be between 2 to 20 MPa, so the experimental conditions were considered reasonable. As a result of the experiments, it was verified that restraint densifies alumina-magnesia castable, resulting in an increase in modulus of rupture and modulus of elasticity. The densification effect of restraint became larger as the MgO content increased. The effects are attributable to an in-situ spinel forming reaction, which improves corrosion resistance.Taking the temperature distribution in the castable lining into account, large restraint stress is expected for the hot face while only a little effect is expected for back end. Thus, excessive difference in material property in the thickness direction, which is undesirable in terms of structural spalling, is a concern.Hence, the MgO content of alumina-magnesia castable should be determined carefully, taking not only corrosion resistance but also spalling resistance into consideration.

Oct 30, 2017

By Delio Amorim

Industry 4.0 concepts is the new biggest challenge on the industry nowadays and every company in every industry in every part of the globe is looking to implement this somehow on their factories and machines. To do that on the newest long rolling mills, that brings already onboard state-of-the-art technologies, is for sure a challenge of machinery builder industry, but how to become the long rolling mills built on 70’s, 80’s or 90’s part of this innovation process and connected to the new trends? This is the main mission here, to show some examples of applications that goes in this direction.

Oct 1, 2019

By Milan Terčelj, Matej Drobne, Urška Klančnik, Peter Fajfar

The study of oxidation behavior of High Chromium Steel material used for surface layer of work rolls was carried out. Specimens taken directly from the roll were subjected to thermal fatigue in the temperature range between room temperature and 500 °C up to 700 °C by using thermo-mechanical simulator Gleeble 1500D. Our observation was focused on the impact of oxidation as a principal mechanism of degradation of the roll’s surface layer - mainly on the characteristics of oxidation propagation in relation to the test temperature and microstructure constituents characteristics of the material. Oxidation is considerably accelerated by certain characteristics of eutectic and primary carbides, i.e. their size (area), composition, morphology, orientation regarding to the water-cooled surface, etc. In the presented paper selected cases where emphasized oxidation takes place are investigated, analyzed and explained. Obtained results thus represent a contribution to explanation of conditions which lead to acceleration of oxidation behavior that in turn can lead to chipping or even early spalling of material from the roll surface layer.

Oct 1, 2019

By Dr. Steven G. Jansto

The market demand for reduced fuel consumption and CO2 emissions in the automotive, energy and construction sectors have further increased the demand for new and advanced higher quality microalloyed grades produced via TMCP. The technological integration of the process and physical metallurgical advancements of value-added niobium (Nb) microalloyed thermo-mechanical controlled process (TMCP) steels continue to be developed and is an important element for these more demanding end user requirements and cost-effective steel production. The reheat furnace process step has a profound effect on the TMCP performance, final hot rolled steel quality and mechanical property consistency during the production of hot rolled steels. The uniformity of heating applied across the entire width, thickness and length of the slab or billet is essential in the successful achievement of consistent customer properties regardless of the chemistry. The resultant ferrite grain size in the final hot rolled product is significantly governed by the initial prior austenite grain size. However, the transition from laboratory melted and TMCP hot rolled heats to the production scale is often quite challenging. Aberrations in the reheating process step at the industrial furnace are often the root cause of mechanical property quality issues. These combustion process metallurgy parameters connect directly to the resultant TMCP product quality and is defined as Combustion Metallurgy

Oct 1, 2019

By Hormando Leocadio, CWM van der Geld, Julio Cesar Passos

Impinging water jets promote high heat flux extraction rate. Steel industry widely employs the process for accurate temperature control to improve the microstructure and to ensure adequate mechanical properties. The range of surface temperatures, heat fluxes and cooling rates are very large, which makes it important to obtain an accurate value of the heat transfer coefficient. This paper presents an experimental and numerical study of the heat transfer behavior of a high temperature (450°C - 900°C) steel plate cooled by a water jet at 20°C to 70°C. High-speed imaging (up to 20,000 fps) within water jet impingement zone allowed the characterization of the boiling regimes in the early stages of cooling. The effects of initial temperature, water jet temperature and velocity on the heat transfer coefficient were analyzed by inverse heat conduction method that predicts the heat flux and temperature on the top surface from temperatures measured with thermocouples inserted in test plate. Heat transfer is strongly affected by the initial temperature of the hot steel, water jet temperature and, less intensely, by jet velocity. High cooling rates start when liquid water is in direct contact with surface temperatures above 700°C.The results will contribute to the enhancement of the temperature cooling control on the runout table and cooling model employed at Usiminas Hot Strip Mill.

Oct 1, 2019

By Carolina Arriel Pedroso Dias

Neste trabalho, tiras de aço inoxidável duplex UNS S32205 foram laminadas a morno a 600°C com 60% e 80% de redução e, em seguida, foram recozidas a 1050°C durante 300 s. A tira como fornecida (laminada a quente industrialmente e recozida) também foi recozida para efeito de comparação. Avaliou-se o comportamento mecânico das amostras como fornecida, 60% e 80% por meio de ensaios de tração e microdureza Vickers, obtendo-se 779 MPa, 730 MPa e 807 MPa de limite de resistência a tração e 265 HV, 244 HV e 256 HV de microdureza Vickers para as três condições descritas, respectivamente. Outros ensaios de microdureza foram realizados ao longo da superfície do corpo de prova fraturado em tração, indicando um aumento da dureza nas regiões mais próximas da fratura. O aumento da dureza na região de estricção indicou o aparecimento da martensita induzida por deformação para as amostras laminadas a morno. Usando a derivada da curva tensão verdadeira em função da deformação verdadeira, (ds/de), avaliou-se o comportamento de encruamento do aço para as três condições. Juntamente com os exames por microscopia eletrônica de alta resolução e difração de raios X, buscou-se uma interpretação dos mecanismos de deformação plástica envolvidos no processo de encruamento. Em determinados estágios, observou-se uma mudança da inclinação para um regime estável, indicando a ocorrência de outros mecanismos de deformação plástica, diferentes do escorregamento de deslocações. A martensita induzida por deformação foi considerada responsável pelo aumento da taxa de encruamento do aço, i.e., por ser obstáculo à movimentação das deslocações e por postergar a formação da estricção.

Oct 30, 2017

By Haruki Inami, Takashi Ishida, Kazuhiro Ohara, Hiroyuki Imanari

The highly competitive business environment of the international metals industry is driving demand for more cost-effective operation of steel making facilities, rolling mills, and strip processing lines. Achieving stable operation is vital if the steel industry is to produce high-quality products constantly and productively. In recent years, advances in computer processing speeds, data acquisition rates, and data storage capacity have rapidly led to greater use of the new technologies of big data, analytics, the IoT, and AI by control system designers and process engineers, and the introduction of industrial applications. The “Smart Rolling Mill” solutions for hot strip mills have been developed by our group with the goal of achieving sophisticated, state of the art, and automated operation in steel rolling mills. The various solution engines improve process stability, increase the performance of mill equipment, and provide improved process control. These solution engines are based on extensive knowledge of the rolling process and the associated control systems. Two solution engines in particular are the diagnosis systems for rolling condition and for product quality that contribute to cost-effective operation and lower yield loss. This paper focuses on the diagnosis systems for rolling condition and for product quality in hot strip mills. Advanced information technologies using big data analytics and machine learning are applied to real-time data collected from the automation system that controls operation and the rolling process. We have developed diagnosis solutions for rolling condition and product quality utilizing predictive and clustering diagnosis. Predictive diagnosis prevents serious problems by detecting changes in the state of the plant or in the rolling condition. Clustering diagnosis classifies patterns of fluctuation in product quality trend charts, providing effective tuning guidance for improving product quality. This paper describes these applications with several examples.

Oct 1, 2019

By Breno Totti Maia

This work was a continuous and multidisciplinary development. Through studies of the blowing process and its parameters results, evolutions, improvements and adjustments were made on the lance’s hot face with Slagless® technology, as well in the process parameters and mitigating actions of the projection of materials out of the converter. The main results are the increase in the nozzle’s life with a “record mark” of 1785 heats, and water leakage occurrence in the cartridge decreased considerably reaching the mark of one year without any occurrence.

Oct 30, 2017

By Anderson José Beber

O trabalho apresenta os resultados da aplicação de um novo oxidante moderado em uma grande torre de resfriamento utilizada em sistema de geração de energia de uma grande usina no sul do Brasil. Esta torre de refrigeração utiliza água de efluente tratado (tratamento terciário Esgoto doméstico) como fonte de reposição. Com aplicação desta nova tecnologia, houve uma melhoria tanto no controle microbiológico como na taxa de corrosão. Além disso, a planta foi capaz de aumentar o ciclo de concentração, resultando em economia de água, produtos químicos e menor geração de efluente, possibilitando economia superior a R$ 500.000/Ano, aplicando conceito de reuso.

Oct 30, 2017

By Daniel Hajduk

Efficiency of back up rolls depends mostly on two parameters – length of campaign and dressing amount after the campaign. The longer the campaign (in terms of rolled tones) is, the higher the dressing amount. To solve this task properly it is necessary to know the distribution of accumulated damage in the working layer of the roll caused by previous campaigns and by loads (separating force and bending) during present campaign respecting changing conditions of material properties (hardness) through radius of the roll. To find an optimum dressing amount an algorithm has been developed and specialized computer program will be presented, that takes real measured loads during the backup roll campaign, calculates fatigue damage in the roll and suggests relevant dressing amount. This can help to prolong service life of rolls, minimize the risk of spalls and reach maximum efficiency in terms of rolled tones/km per roll.

Jul 30, 2018

By André De Araujo Abilio

Geopolímero é um material inorgânico formado por ativação alcalina durante a qual processos de polimerização de alumino-silicatos formam a cadeia polimérica que consiste em tetraedros de Si-O e Al-O. Com o intuito de encontrar subprodutos para serem usados como uma alternativa de aglomerante na formulação do geopolímero, um subproduto oriundo do processamento de rochas ornamentais foi utilizado. O presente estudo consiste na caracterização da capacidade de flexão do material geopolimérico resultante da adição do granito como aglomerante alternativo. Estudos foram elaborados de modo a avaliar ambos o efeito e a viabilidade de seu uso em formulações futuras do geopolímero.

Aug 16, 2017

By Roberto Parreiras Tavares, Leonardo José Silva de Oliveira, Marcelo Moreira Furst Goncalves, Rodrigo Seara Martins

Os pós fluxantes estão continuamente sendo desenvolvidos para permitir que o processo de lingotamento contínuo possa gerar produtos de melhor qualidade superficial. Entretanto, a seleção e a avaliação do desempenho industrial desse insumo não são simples por envolver o conhecimento simultâneo de várias propriedades físico-químicas. Nesse sentido, desde que medido de forma adequada, o consumo do pó fluxante no molde é uma ferramenta útil para avaliar a estabilidade operacional. Assim, foi desenvolvido um sistema para quantificar o consumo específico dos pós fluxantes no molde para posteriormente correlacioná-lo com eventos que possam levar a desvios de qualidade superficial do produto lingotado.

Oct 1, 2019

By Camila Simon Christ

A crescente demanda de aços com composições e propriedades controladas aumenta as exigências do controle de qualidade dos produtos acabados e dos constituintes deletérios, como as inclusões, que são agregados durante os processos de fabricação e acabamento. No presente trabalho foi realizada uma análise qualitativa e quantitativa das inclusões presentes em um aço microligado de partida de máquina, através da observação de imagens obtidas por microscópio ótico. A observação das imagens permitiu verificar uma falta de homogeneidade ou padrão na ocorrência das inclusões nas amostras e que as inclusões presentes eram do tipo óxidos glogulares e alumina.

Oct 30, 2017

By Saulo Rossini Meira

A complexidade e o elevado tempo de manutenção para a troca do rolamento da grelha móvel do forno da usina de pelotização IV, localizada no Complexo de Tubarão em Vitória - Espírito Santo, viabilizou estudar, desenvolver e implementar, via PDCA, uma solução tecnológica que reduziu riscos de acidentes, tempo de manutenção, desgaste físico e mental, como também eliminou a utilização de equipamentos móveis e o risco de quebra de componentes periféricos. Conclui-se que com a modificação implementada, foram viabilizados procedimentos de manutenção mais seguros, redução de custos e aumento da disponibilidade do equipamento para o processo produtivo.

Aug 1, 2018

By Melina Gamis da Silva

Em um trabalho anterior [1], as temperaturas de processamento aplicadas na laminação de tiras a quente, LTQ, da CSN foram investigados para algumas classes de aços microligados ao Nb. Os resultados deste trabalho mostraram a possibilidade da redução da temperatura de reaquecimento utilizada para esses aços refletindo em possibilidades de melhoria de produtividade. No trabalho atual, o impacto dessas mudanças na microestrutura obtida de LTQ foi investigado com mais profundidade, utilizando um software desenvolvido para prever a evolução da microestrutura em termos das frações recristalizadas, das distribuições de tamanhos de grãos e do comportamento das tensões médias de escoamento, TME.

Oct 30, 2017

By Jorge Luis Braz Medeiros

As ligas de Alumínio ASTM 2014, caracterizam-se por apresentarem elevada resistência mecânica, quando comparadas a demais ligas de Alumínio. Este comportamento está associado ao tratamento térmico de Solubilização e envelhecimento, sendo que no envelhecimento artificial existem diferentes curvas de avaliação do limite de resistência, limite de escoamento, alongamento etc. Neste trabalho serão apresentados os efeitos da cura de revestimento de Politetrafluoretileno, realizado a 230ºC, nas propriedades mecânicas e na dureza, destas ligas, após a condição preliminar de solubilização. O Politetrafluoretileno confere baixo coeficiente de atrito e acabamento diferenciado, sendo comparado seu efeito com processos de anodização.

Aug 7, 2018

By Michelle Lacerda Sales Marques

A busca de novas rotas de beneficiamento que possam maximizar a recuperação metalúrgica e mássica é uma constante na Vale. O trabalho foi desenvolvido em três fases, onde foram estudadas quatro rotas de beneficiamento que buscaram reduzir a geração de ultrafinos e, assim, aumentar a recuperação mássica. Foram avaliadas rotas com pré-concentração do minério em concentração magnética (rota denominada PCM) e flotação (rota denominada MFMF), e uma rota onde a moagem mais grossa (P80 0,15mm) permite uma menor geração de ultrafinos (rota denominada MDMF). Esta última apresentou um CAPEX 6,5% menor quando comparado a rota PCM.

Aug 1, 2018