Search Documents

By Giuseppe Pintaude

The use of two-dimensional shape parameters to characterize abrasive particles is a possible approach to express their angularity. Nonetheless, in sliding abrasion, especially in pin abrasion testing, coated papers structure plays an important role and even its damage during the wear process should not be neglected. This manuscript discuss the limitations of two-dimensional shape descriptors in distinguishing wear caused by relatively hard particles, indicating that the wear data obtained in sliding abrasion tests are unable to distinguish different types of coated papers used when only the two-dimensional particle projection is considered for shape characterization.

Jul 31, 2018

By Bernhard Hiebl

Global trends that are constantly challenging the iron and steel producers are related to worsening of the iron ore grades, higher substitution rates of main iron ores to cheaper raw materials due to economic pressure and increased environmental standards. Changing the raw materials in an operating plant can significantly influence the sintering or pelletizing process. Adjusting all process parameters to regain stable and high productive operation takes considerable time and causes production losses. Furthermore changes in raw materials lead to variations in the process gas flows and emission concentrations.Therefore SVAI developed two models for numerical simulation of sintering process and pelletizing process. Amongst others the models are based on Ergun equation and include chemical reactions of the related process. For already operating plants the simulations shall predict changes of the process parameters when raw materials are exchanged or when operational parameters are varied. Furthermore the simulations give advantageous information for the design of green field plants and allow the simulation of different plant configurations.The objective of this paper is to demonstrate what the latest developments are in these numerical simulations and what Siemens VAI is doing to overcome the remaining challenges in this field.

Aug 2, 2018

By Daniel Wild, Tobias Scheffer, Marvin Laugwitz, Martin Jochum

Leveling is a standard process in the rolling mill to eliminate flatness deviations. The process layout is based on models and the leveling result depends on the accuracy of the material parameters in these models. Even small deviations from the correct assumptions can have a major effect on the final flatness. Thus, after leveling the products may look optically flat, but subsequent to a final cutting process springback occurs due to residual stresses. The objective of this work is to analyze the influence of material parameters and gravity on the flatness after leveling. To evaluate the sensitivity of the process, an FE parameter study is exerted that reveals the influence of fluctuations in material properties in the case that the leveling setup is fixed. Gravity is neglected to not conceal flatness deviations. Examples of this study are rerun in a further step under consideration of gravity to also analyze its influence on the resulting flatness and residual stresses. Finally, to analyze the consequence of the residual stresses, all information of the plate from the previous step are transferred while gravity is suppressed to prompt springback. This study revealed that slight deviations of the material properties can lead to uneven plates in simulations where gravity is not considered. If gravity is taken into account, the unevenness is concealed and the plate seems flat. A springback simulation of the same plate shows that strong residual stresses are still present and would lead to unevenness if e.g. the plate were cut.

Oct 1, 2019

By Wolfgang Oberaigner

Primetals Technologies has always been a driver of innovation in steelmaking, especially by providing sophisticated process expert models for continuous casting machines. This capability is demonstrated by recent advancements in automation solutions that include: DynaPhase, Dynacs 3D, and DynaGap. This state-of-the-art suite of dynamic secondary cooling and soft-reduction packages take into account thermodynamic effects such as shrinkage and phase transitions, and thereby significantly contribute to direct quality improvements during the solidification phase in the continuous casting process. Speed Expert calculates an optimum casting speed for every casting situation, and additionally recommends a strand speed so that the point of final solidification is positioned at the end of a segment for optimum soft reduction. In the case of steel grade changes, the Intermix Expert precisely calculates the chemical properties of the mixed steel, thereby minimizing losses due to deviations from required specifications. The Nozzle Expert is a new model that detects clogged nozzles and broken hoses in secondary cooling systems. The first installations were highly successful and customers are pleased with impressive reductions in maintenance costs and improved steel quality. This paper describes these innovative process automation solutions and gives an overview about the successful results achieved within the first installations.

Aug 16, 2017

By Ananda Moreira Vaz Ourique de Avila

High and intermediate temperature fuel cells (FC) are power generators characterized by high efficiency and their use in cogeneration systems. The single fuel cells are connected in series by the use of interconnects to form a fuel cell stack. Ferritic stainless steels have been used in the making of high and intermediate temperature operation solid oxide fuel cells interconnects. However, at high temperatures, on the order of 700-8500C, these steels can present significant oxidation and degradation processes, promoting increased electrical resistivity and corrosion losses that result in contamination of the electrodes and reducing the performance and the useful life of the FC. Intensive R&D activities have been made to minimize these problems and the use of composite coatings on metallic substrate has been considered. This paper evaluates the use of coatings of copper and nickel, with particles of La2O3, Y2O3, CeO2, LaCrO3 and doped chromites applied on ferritic stainless steels AISI 430, AISI 441 and Crofer22APU produced by electrodeposition. The produced samples were evaluated by microscopy techniques, gravimetric analysis and by electrothermal characterization. The most significant results were obtained with chromites coatings (LaCrO3 pure, mono- and multiple-doped) showing the combination of the best features of metal coatings, substrates and ceramic particles with semiconductor properties.

Aug 7, 2018

By Edgard de Macedo Silva

Aços inoxidáveis duplex apresentam boas propriedades mecânicas e de resistência à corrosão, mas quando são colocados para trabalhar em altas temperaturas como no processo de soldagem e de tratamento térmico ocorre o surgimento de fases que comprometem as suas propriedades. Dentre elas, a fase sigma (s) é a que apresenta um maior efeito de fragilização por ser rica em cromo e empobrecer a matriz desse elemento, bem como por apresentar dureza em torno de 1000HV. No presente trabalho, uma metodologia não destrutiva, baseada na interação entre densidade de linhas de campo e um aço inoxidável duplex, é apresentada para o acompanhamento da formação da fase s na temperatura de 800°C em um aço envelhecido por até 2 horas. Diferentes intensidades de campo foram geradas por um eletroímã e o fluxo de linhas de campo foi aplicado no material de estudo. A densidade de linhas de campo resultante foi medida por um sensor de efeito Hall. Os resultados foram correlacionados com resultados de microscopia eletrônica de varredura (MEV), dureza e difração de raios-X (DRX) e mostraram que os valores de tensão hall reduziram à medida que a fração volumétrica da fase s aumentou. A formação dessa fase não magnética influenciou no sinal obtido pelo sensor Hall. Existiu uma correlação entre a densidade de linhas de campo resultante e a presença da fase fragilizante, apontando para uma metodologia capaz de acompanhar a formação dessa fase.

Aug 8, 2018

By Steven George Jansto

The hot ductility behavior of different microalloyed steel chemical compositions was examined simulating the thermal and strain conditions through the straightening or unbending section of the continuous casting machine. All samples were obtained from industrial slab casters ranging from 200 to 300 mm in slab thickness from steel mills throughout the world including China, Brazil, North America and Europe. The slabs were crack-free and hot rolled into prime quality products. No laboratory heats were tested. Although these microalloyed steels exhibit inherently lower hot ductility behavior, as measured by percent reduction in area at elevated temperature, these steels still exhibit sufficient ductility to satisfactorily meet the unbending stress and strain gradients existing in the straightening section of most casters. The majority of the published hot ductility data, as measured by % reduction in area (%RA), were based on laboratory heats and hence, are inaccurate in accessing the propensity for slab cracking on an industrial caster. This situation then results in invalid conclusions for different chemistries. This research has determined the minimum required %RA for crack-free casting is significantly lower than results based upon previously published laboratory generated data. For example, the literature quotes 40% RA minimum for Nb-bearing steels when in fact as low as 10% minimum RA is more than sufficient to assure crack-free casting based upon the extensive testing and analysis performed in this study. Instead of %RA, the measurement of strain energy has been introduced to evaluate hot ductility behavior. It is concluded that strain energy is a better measure of hot ductility behaviour than %RA. There is considerable value in the evaluation of the hot stress and strain curves, process metallurgy parameters and their relationship to slab quality instead of just basing hot ductility decisions on simple %RA measurements.

Aug 16, 2017

By HaiWen Luo, Bin Hu

A ultra-high strength medium Mn steel with good ductility was designed and manufactured via the combination of warm rolling and V alloying, which produced not only the extensive precipitation of fine VC particles in both ferrite and austenite but also the bimodal size distribution of retained austenite (RA) grains. A substantial increase of yield strength up to 650 MPa was achieved due to the addition of V without deteriorating ductility. The coarse RA grains firstly transformed to martensite during yielding at the much higher stress threshold, followed by a significant work hardening due to dislocations multiplication, twinning-induced-plasticity (TWIP) and transformation-induced-plasticity (TRIP) in the ultrafine RA grains. The best combination of strength and ductility included 1.5 GPa ultimate tensile strength and 28% total elongation. This was achieved due to the sustainable TRIP and TWIP effects in the later straining stage resulting from the ultrafine austenite grains, the latter were reversely transformed from the recrystallized ferrite grains.

Oct 1, 2019

By Andreas Jungbauer

Two Arvedi ESP plants going into operation in 2015 will allow a Chinese steel producer to better serve the extremely attractive local and export markets for high-quality, thin-gauge strip products. The energy consumption and the related costs are reduced by up to 45% compared to conventional casting and rolling processes. This also means a major reduction in CO2 emissions. The new plants are designed for an annual production capacity of 2 x 2.55 million tons of high-quality, ultra-thin, hot-rolled strip products with widths of up to 1,600 mm and thicknesses down to 0.8 mm. The project scope also features a comprehensive training and assistance package for plant start-up and operations by personnel from the existing ESP plant at Acciaieria Arvedi SpA, Italy. The plant setup, the trainings and assistance program as well as latest results from the ESP plant in Italy will be presented. While this project is under execution three further ESP lines have been ordered by the same customer summing up now to five ESP lines at the same location.

Jul 30, 2018

By Martim Hideki Nakayama Kurauchi

One of the main issues regarding the use of charcoal in metallurgical processes is its mechanical strength, which is much lower than coke. There is no defined standard to determine charcoal compression strength, and the methods described in the literature consist in using a prepared specimen and applying compressing load in the same direction of the charcoal fibres. As charcoal is highly anisotropic, it is proposed a procedure that does not use a specimen and with load applied on a specific direction. Instead, it intends to simulate industrial conditions by randomly dumping charcoal inside a tube, without preferential directional arrangement. This is an attempt to determine charcoal mechanical strength and predict the behaviour of bulk charcoal under a static load, as in a blast furnace. Experiments with controlled loads have been carried out on randomly distributed bulk charcoal with controlled initial size and their effect on the size distribution has been analysed. After compression, charcoal is screened and each size is weighed, determining the particle size distribution of the experiment. This method can therefore be used to evaluate charcoal mechanical strength.

Aug 1, 2018

By Jean Viana Bahia, Antônio Adel dos Santos, Vicente Tadeu Lopes Buono

During cold rolling of Cr-Mo alloyed DP steel, considerable oscillation of thickness may occur. The literature points out that such occurrence is due to non-uniform cooling of the coil after the hot rolling process. Since the austenite transformation in this steel continues after coiling, the microstructure and, consequently, mechanical properties are very susceptible to natural variations in cooling rates associated with distinct positions of the coil. The influence of coil cooling conditions on thickness oscillation during cold rolling was evaluated in this work by using both industrial experiments and dilatometer tests. It was verified that an industrial coil presented large variation of mechanical properties associated with its heterogeneous microstructure. Consequently, thickness oscillation occurred during cold rolling. Dilatometer tests simulating hot run-out table and coil cooling showed that the austenite transformation is very slow under small cooling rates that occur after coiling. Thus, the slow transformation rate makes the coil very susceptible to environmental conditions around it during its natural cooling and is responsible for variation in mechanical properties of the coil. To ensure the formation of a more homogeneous microstructure in the whole coil, it is necessary either to make use of technologies that improves the cooling uniformity or to adjust the steel alloy design. The latter alternative has been done with relative success by using conceptions with lower amounts of Cr and Mo.

Oct 1, 2019

By Daniele Tolazzi

In today’s highly competitive market situation, it is of outmost importance for EAF steel makers to optimise their processes in order to reduce operating costs and to improve safety and reliability of the equipment. The laser based off-gas analysis technology, With laser units installed on the fix duct, downstream the combustion gap, uses the “Tuneable Diode Laser Absorption Spectroscopy” (TDLAS). The system performs real-time off-gas emissions measurements of CO, CO2, O2, H2O and temperature. A closed-loop operation is in place for dynamic control of the chemical energy package combustion/post-combustion of CO, H2 and CH4 gases into the EAF furnace shell. A statistical framework which builds on a data analysis engine, based on Danieli Automation Q3Intelligence technology, evaluates the “fingerprint” of the process represented by average and deviation trends of both gases and other process parameters. Process fingerprinting is conceived both for offline profile optimisation and on-line control of the refining process. This paper describes how the technology has been applied and the results achieved at ACCIAIERIE BERTOLI SAFAU (Italy) 100 t AC Electric Arc Furnace.

Aug 16, 2017

By Bi Zongyue, ZhangYongqing, NiuTao, Guo Aimin

Over the past twenty years, significant advances have been made in the field of microalloying steels and associated applications, among which one of the most successful application cases is development and application of heavy-gauge X80 coil with high temperature processing HTP practice used for China's Second West-East pipeline, the longest X80 pipe in the world. During this process, HTP design concept has been sucessfully applied to develop 18.4mm X80 coil with demanding low-temperature fracture toughness requirements. In the meanwhile, China's metallurgical workers have further optimized HTP design concept with the aid of powerful rolling mill and coiling equipment, and made it possible to develop 21.4mm X80 coil used for Russia-China East line. In the paper, we would simply review the development history of high-strength pipeline steels, and then give more priority to the fundamental points for sucessful development of 18.4mm X80 coil and SSAW pipe, which paved the way for subsequent development of 21.4mm X80 coil and SSAW pipe. Finally, we would present the test results of mass production and burst tests, and dispel the suspicion that SSAW pipes made of X80 coil are more qualified to resist ductile fracture.

Oct 1, 2019

By Gustavo Henrique Bolognesi Donato

Ensaios de curva R (J vs. ?a – crescimento dúctil de defeitos) e de propagação de trincas por fadiga (da/dN vs. ?K) são balizados por normas como a ASTM E1820, ISO 12135 e E647, as quais exigem dimensões mínimas para as amostras C(T) ou SE(B) a fim de garantir condições SSY e portanto a validade de K e J. Entretanto, tais exigências usualmente conduzem a dimensões expressivas que dificultam a retirada de amostras de chapas finas ou mesmo de muitas estruturas reais. Como alternativa, estudos de Koppenhoefer e Dodds (1998) e mais recentemente de Shin e Lin (2012) indicaram a possibilidade de uso de amostras em miniatura (inclusive Charpy contendo pré-trinca) para determinação de curvas R e da/dN vs. ?K. As grandes questões são a viabilidade de ensaio de amostras pequenas com repetibilidade e a adequada avaliação dos limites de validade das forças motrizes nestas geometrias, a fim de garantir condições de similitude. Como um passo nesta direção, este trabalho investiga o potencial de amostras Charpy pré-trincadas (10x10x70mm) na determinação de curvas R e da/dN vs. ?K. Inicialmente, ensaios de ambos os tipos foram realizados em amostras de um aço estrutural ferrítico empregando uma máquina universal MTS 810. Apesar das dimensões reduzidas dos espécimes, os ensaios se mostraram viáveis e apresentaram boa repetibilidade e estabilidade dos resultados experimentais. Ainda, boas práticas de ensaio puderam ser estabelecidas para suportar os trabalhos futuros com tais geometrias.

Aug 8, 2018

By Jörg Busch

The essential pre-requisite for attaining the high quality of product required from high-speed continuous production processes is the use of new measurement and control technologies. High availability and reproducible measuring results ensure the high level of process stability necessary for full continuous operation. The requirements for the optimisation of quality across the complete production process and for quality analysis systems will be discussed. This report will present examples of basic and new measurement technologies in Cold Rolling Mills and Processing Lines. The following gauging systems will be discussed in detail: Strip tension meter, roll force measurements, weighing systems and shapemeter rolls. The measuring and control systems in this presentation must be seen as high-tech solutions in the field of processing technology. The measuring methods and technologies described are, together with optimised process models and precision control loops and actuators, the main pre-requisites for achieving the quality of product required from high-speed continuous production processes. Interconnected quality management systems enable optimisation across the complete production process.

Jul 30, 2018

By Danilo Gonçalves de Oliveira

A linha de Decapagem e Laminação a Frio da ArcelorMIttal Vega vem recebendo constantes investimentos para aumento da sua capacidade produtiva sendo o mais recente a instalação do quarto tanque de decapagem química realizada em março de 2015. Para que esse investimento trouxesse o resultado esperado, eram esperadas melhorias de desempenho no processo de Laminação a Frio. O presente trabalho expõe a metodologia empregada para identificar os projetos necessários e os expressivos resultados obtidos com a sua condução ao longo do ano de 2014.

Aug 16, 2017

By Cláudio S. S. Pinto

Em face do agravamento da situação da energia elétrica no Brasil, com disponibilidade cada vez mais restrita e custo cada vez maior, torna-se urgente reduzir o seu consumo onde possível. Ventiladores centrífugos de processo de médio e grande porte são grandes consumidores de energia elétrica e podem ter um elevado potencial para a redução do seu consumo. Este texto mostra como identificar a possibilidade de economizar o uso da energia elétrica em um determinado ventilador e que modificações ele necessita para cumprir este objetivo.

Sep 25, 2017

By Carlos Alexandre Gonçalves de Moura

O trabalho se baseia na redução do retorno parcial de aço por temperatura na Aciaria LD com foco em análise estatísticas do processo, melhorias no projeto alinhado ao plano de manutenção dos componentes mecânicos e elétricos do sistema de aquecimento de panelas. Para análise do problema foi elaborado um estudo utilizando Lean Six Sigma através do DMAIC, analisando as condições de processo, procedimento operacional e plano de manutenção dos equipamentos. Como resultado do trabalho obteve-se uma redução em 58% no retorno parcial em panelas de aquecedor.

Jul 30, 2018

By Mariano de Córdova

In this paper, the coke oven life prolongation technology is reviewed from different points of view: blend design; battery heating; operational control; refractory maintenance. A summary of major inspections in critical areas, for the evaluation of the battery conservation situation is presented. A discussion on tools for the diagnostics of the degree of damage is carried out.

Aug 16, 2017

By Dagoberto Brandão Santos, Kairo de Barros Guimarães, Túlio Magno Füzessy de Melo

The effect of the cooling conditions on the microstructure and hardness of a Dual Phase hot-rolled steel 800 MPa strength was investigated. Simulations of the cooling conditions using a dilatometer were carried out from samples of a hot rolled coil with variations of the intermediary temperature from 620 to 740°C, isothermal holding time between 1 and 10 s and coiling temperature between 50 and 400°C. In addition, two CCT (Continuous Cooling Transformation) diagrams were developed to evaluate the effect of the isothermal holding time on the phase transformations of the remaining austenite. It was observed that the intermediary temperature has a strong influence on the kinetics of the phase transformation, as well as the isothermal holding time influences the amount of ferrite formed and, consequently, the final microstructure and hardness of the material. The coiling temperature did not cause significant changes in the amount and morphology of the ferrite, but a gradual replacement of martensite with bainite was observed, which, in addition to the self-tempering effect, contributed to the hardness reduction.

Oct 1, 2019