Search Documents

By P J. Dailey, S L. Burchell, R F. Chiappetta

In recent years, high-speed motion picture photography has become a powerful diagnostic tool and technique to study, analyze, evaluate, and aid in blast designs. Production blasting, typically lasting less than two seconds, requires an extended time base for observation and clarification of short-lived phenomena. Information obtained from high-speed photographic analysis is categorized into two main groups.

Jan 1, 1989

By John P. Hager

A special inlet system has been developed for a TOF mass spectrometer that allows the equilibrated high-temperature vapors from an atmospheric-pressure flow reactor to be leaked into the ion source of the mass spectrometer without undergoing any compositional changes. Using this flow reactor - mass spectrometer system and a modified transpiration system (one that allows for the carrier stream to be equilibrated with two different condensed samples) a series of fundamental vapor transport studies were undertaken. The results of these studies are summarized as follows: 1. The vapor species in equilibrium with condensed copper (I) chloride were determined to be Cu3C13, Cu4C14, and Cu5C15. The gas mixture is fifty percent tetramer near the melting point (703°K), with the percentage of tetramer decreasing with increasing temperature. The following thermodynamic results were obtained.

Jan 1, 1977

By Charles Stone, Hannes Lagger, Dru Desai

The design methodology of the planned Second Avenue Subway Project (SAS) led to development of the initial support design to estimate cost and quantities in the Preliminary Engineering (PE) stage. Careful selection of the cavern design rules that recognized the impact of rock quality, rock cover, excavation geometry, and excavation sequence helped to overcome the design challenges of large, shallow caverns for the initial ground support. In the course of the design verification process prescribed by the design methodology, the design team was continuously reviewing and updating the support quantities. The design procedure includes methods using different approaches of empirical, continuum, and discontinuum analyses, which are currently advanced in the Final Engineering (FE) stage. The paper is a continuation of the RETC 2005 “Trials and Tribulations” and focuses on the procedures that led to the changes in the initial support as a result of the ongoing design development.

Jan 1, 2007

The French research institute, INERIS, requested the assistance of the CSIR?s Division of Mining Technology in developing further precautionary measures against explosions in their collieries. In response to this approach, an on-board active suppression system was adapted to meet their mining requirements. This system is used on tunnelling machines in Germany where the machine is positioned in the middle of the tunnel, which is therefore not much wider than the machine itself. With this configuration, the machine is never away from the tunnel face during the cutting cycle. As a result, the possible volume in front of the machine of combustible gas requiring suppression is less than 50 m3. In South Africa this technology has been adapted to suit a two-cut mining method which entails greater distances from the face and thus much larger volumes of methane mixtures requiring suppression. The particular configuration of the Explo-Stop® system being investigated required the suppression of possible methane ignition volumes of up to 180 m3of a 9% per volume methane/air mixture. The volume is a consequence of the large cross-sectional area of French underground workings and of the two-cut mining method used in France. In order to take the second cut in the coal seam, the machine is pulled back a maximum distance of 4 m, leaving an air pocket in which gas can accumulate. The machine-mounted system is required to effectively suppress any flame ignited by such a large accumulated volume of methane. The results of the protocol tests done at Kloppersbos showed that the system was capable of suppressing all simulated methane ignitions for the prescribed conditions. This was achieved with a temperature increase of less than a 100°C at the operator?s position and without any flame being detected at this position.

Jan 1, 2001

By Jie Li

Series of carbon compounds as anode materials were prepared for super lithium ion capacitor using graphite and active carbon (AC) as raw materials. Their electrochemical properties were investigated by constant current charge-discharge test. The results showed that the compound anode had good capacitive performance as well as Li-ion battery performance. The potential of the capacitor could be as high as 3.5V vs Li/Li+ when compared with 2.5V vs Li/Li+ in the AC-AC capacitor, accordingly, the energy density increased from 21.7Wh/kg to 40.3Wh/kg. The compound anode also had excellent rate performance that as the current density increasing from 0.1A/g to 1A/g,the capacitance decreased only 1.3F/g, and good cycle performance that the capacitance holding remained 96.7% after 10 times cycles even at the highest potential of 3.5 V vs Li/Li+.

Jan 1, 2009

This paper investigates the effects of solids concentration and the addition of Dispersant S40 on the flowability of original and ground limestone slurries. A rotational viscometer with a concentric cylinder geometry and a controlled-stress rheometer with a cone-and-plate geometry were used to characterize the rheological behaviors of limestone slurries. The rheological behavior of original limestone slurries (<100 µm) is transformed through different types of flows with increasing solids concentration. The use of Dispersant S40 can improve the slurry flowability by decreasing viscosity and eliminating Casson yield stress. It is therefore used as a grinding aid for the wet ultrafine grinding of limestone. The rheological behaviors of ground limestone slurries vary with grinding from a starting dilatant flow-ability to a resulting pseudoplastic one with an evident Casson yield stress in combination with a thixotropic character. The appearance of pseudoplastic flowability combining thixotropy is related to the fineness of a ground product and its specific surface area, which are both correlated to solids concentration and the additive amount of Dispersant S40. In addition, the accurate rheological characterization of time-dependent fluids is dependent on the instruments used and operation conditions.

Jan 1, 2007

By Alejandro Ferrada Vergara

Most blasting techniques that are designed to improve fragmentation and subsequently improve ore work index to downstream comminution processes, apply powder or energy factor increases, either by stretching the drilling pattern (burden/spacing ratio) implementing faster initiation sequences or using more energetic explosives. The new application will move detonation parameters up, making the blasting process riskier for the surrounding boreholes, explosive column or initiation systems functioning.

Jan 1, 2016

By Sidney Katell

This study estimates capital investment, operating costs, and selling prices for four underground bituminous mines producing coal with annual production ranging from 1.06 to 4.99 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of December 6, 1974, under the Bituminous Wage Agreement of 1974, and costs for material and equipment are based on 1975 indexes. Initial capital investment ranges from $20,799,800 for the 1 .06- million-ton-per-year (MM tpy) mine to $84,027,500 for the 4.99-MM-tpy mine. Total capital investment ranges from $32,506,800 to $1 22,983,500 for the same mines. Corresponding selling prices for the coal range from $12.87 to $11.64 per ton, assuming a 15-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1976

By Neal Lee, Braden T. Lusk, Jhon Silva-Castro, Patrick J. Jenks

"Timing and charge sequence are very important for optimized blast design. Traditional nonelectricinitiation systems have moved the industry toward a system of delays consisting of hole-to-hole androw-to-row timing sequences that mimic the application of nonelectric surface delays or dual delayinitiator systems that have been prevalent in the blasting industry for many years. The increasedutilization of electronic detonators allows for the use of Regular Rhythmic Timing (RRT) utilizing onlyone delay between charges and a selected charge firing sequence. The hole to hole and row to row (HHRR) timing method has been utilized for blasting optimization and allows for simplistic changes to the tie in phase of the blasting sequence. When using this traditional timing methodology, for some specific cases related to the number holes and rows, crowding occurs in the delay between charges with subsequent increase in the peak particle velocity (PPV) produced by the blast. This is in contrast to RRT where the timing between the delays remains constant."

Jan 1, 2016

By Patrick D. Plumb

The Juneau Office of the U.S. Bureau of Mines has undertaken a study of the environmental permitting process for major mines in Alaska to identify the effects ecosystem management has had or could have on the permitting process. To date, ecosystem management affects major mine permitting in Alaska primarily through the NEPA environmental assessment process. In Alaska, only the Forest Service has instituted ecosystem management in an overt and organized manner, while other agencies are doing so less directly. In recent Bureau of Mines publications, the mine permitting process has been described using case studies of several recently permitted mines in Alaska. The insights into the permitting process and the conclusions of these reports are reviewed and summarized. Several ecosystem management issues were identified in the case studies, including the need for: effective communication between agencies; standardization and coordination of NEPA environmental impact assessment and environmental monitoring programs among agencies, and assessment and selection of alternatives based on risks to ecosystems regardless of jurisdictional boundaries or environmental media-specific regulations. Ecosystem management could be used as a way to systematize, organize, standardize, and coordinate permitting and monitoring requirements and management perspectives among government agencies and project proponents.

Jan 1, 1993

By Kennedy G. L

Operating experience with the pilot Lurgi carbonization plant at Morwell showed that under conventional operating conditions, although the thermal efficiency of the plant was very&apos; high, the physical quality of the char produced was extremely poor. By variation of operating conditions to produce the slow drying rate developed by the laboratory research at the University of Melbourne, an improvement in the size of the char was achieved. A similar approach in the carbonization stage where severe breakage of the briquettes still occurred was not possible due to insufficient control over the heating in this stage. Theoretical analysis of the heat exchange process has shown that severe heating of the briquettes entering the carbonizer is a characteristic of the Lurgi system and cannot be controlled by modified operation. The plant has been closed down for reconstruction of the heating system to enable it to be used to produce hard char.INTRODUCTIONAn experimental carbonization plant was operated at the Morwell Works of the &apos;Gas and Fuel Corporation from November 1958 until July 1959. This plant was built as a pilot plant by the Corporation to designs supplied by the Lurgi Gesellschaft fur Warmetechnik and had the nominal capacity to carbonize 25 tons of brown coal briquettes and to produce 11 tons of char per day. The briquettes were supplied from the&#183; normal production of the Yallourn briquette factory and the 2t in. I-type briquette was the largest size which the plant could handle.This carbonization plant represents the intermediate stage of development between the laboratory research at the University of Melbourne and the commercial production of hard char as a metallurgical fuel. It is intended in the first place for the study of the technical problems in the handling and...

Jan 1, 1960

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. d., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management 156, Ataturk Bulvarl-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 8 Howard-Canfield Bldg. Santa Barbers, Calif. COWIN & CO. Mining Engineers and Contractors Consulting Shaft & Slope Sinking Appraisal Mine Development Reports Mine Plant Construction I. 18th St. S. W. Wham, Ale., Phone 56-5566]

Jan 1, 1952

By HARRINCTON EMERSON

UNEMPLOYMENT is the most ominous shadow ahead of the industrial nations today. Only two great industrial countries are free from unemployment, France and the Soviet Commonwealth. In France the social unit is the family, not the individual. This has saved France. In the Soviet Commonwealth, development is proceeding so rapidly from agricultural to industrial that there is still a dearth of muscle workers in the non-agricultural enterprises. In the other industrial countries unemployment results both from acute temporary recession in industrial activities and from the rapidly increasing substitution of the machine for the man. Temporary recessions can be mitigated, alleviated by makeshifts, often ill considered. Secular recessions due to a fundamental change in the way of accomplishing physical, chemical results cannot be cured by any makeshift. There must be a period of transition. There is therefore before us the three- fold problem, immediate, prosimate and ultimate.

Jan 1, 1930

By P J. B Fransen

Several spatially and/or temporally distinct phases of epithermal activity can be recognised in the Horohoro-Matahana Basin area of the Taupo Volcanic Zone. In the northern Matahana Basin a 140 - 350 ka age range is proposed for mineralised debris flow clasts and related (?) epithermal &nbsp;mineralisation intersected in a recent drillhole. To the east, a ca. 40 - 50 ka age range is suggested for epithermal activity in the Waikaukau alteration zone which was focused along the Guthrie Fault. Hydrothermal explosion breccias occur over 13 km within the Guthrie Graben, and are probably sourced from vents in the south. Assuming a common origin, these breccias are constrained to a 45 - 50 ka age range. Within the Horohoro hydrothermal system (around the present hot spring), older (15 - 50 ka) and younger (0 - 15 ka) features can be distinguished.

Jan 1, 1991

By W. H. Tomlinson

Although the thoughts and efforts of the great majority of people in many parts of the world are today directed toward killing each other, the purpose of this paper is to discuss means of conserving human life. In a world of turmoil and strife, we find time to discuss and make plans to achieve our objective -prevention of the "sacrifice" of life through avoidable accidents. The word" sacrifice" is used here advisedly, as one meaning of the word given in the 1942 edition of Funk and Wagnalls New Dictionary of the English Language is "the act of giving up some desired or valued object for the sake of *** future good." As everyone agrees that life is man&apos;s most priceless possession, one wonders if past sacrifices have been in vain. It appears that life is cheap in America; it is cheap because some of the industrialists are too much concerned with making a profit to devote much time and thought to conserving human life; it is cheap because some labor leaders apparently are interested solely in personal power and prestige; it is cheap because a great many workmen fail or refuse to cooperate energetically with the various organizations interested ill; their safety and welfare; it is of little value because, individually and collectively, we are indifferent to our responsibilities toward our fellow men.

Jan 1, 1944

By Arthur Dubé

An account is given of the developments brought about in the last fifteen years by metallurgical research in the field of heat treatment of steels. The practical aspects of these developments are especially emphasized. Methods of representation of the phase-change during austenitizing and sub-critical transformation of austenite are described and the importance of time-temperature-transformation charts for the planning of heat treatment cycles is shown. Special copies such as retained austenite and internal stresses developed on quenching are also discussed in some detail. Due to the interest shown currently in these problems, it has been thought advisable to describe briefly the underlying principles and present some of the results already available.

Jan 1, 1945

By Koehler Stout

Many hydraulic backfills are deposited at low density and provide less than optimum support strength to stope walls. This laboratory study shove that fill strength can be considerably increased. Placement methods used to increase the fill strength were the head, vibratory, cementation, double-planed (dblplod), and combinations of these methods. An experimental facility van designed to study the placement cathode and resultant strengths of the fills. Physical property tests made on the fills included laboratory penetration and vane shear plus several supplementary tests, such as grain size distribution and relative density. Test results were compared to fills planed by conventional methods and to those results reported by other investigators. When compared to fills placed by conventional methods, the penetration modulus was increased by 4.3 tines when the uncemented-vibrated-head concept was used and 71 times when the cemented-vibrated-head-dblplod concept was used. Apparently, hydraulically fill strength can be substantially increased. Conceptual mining plans are also included on suggested ways of placing and using high-modulus backfills.

Jan 1, 1979

By Suk han Jang

This paper describes the tower foundation design and construction experience for the 345kV Youngheung marine transmission line, which has been in commercial operation in Korea since July, 2004. This transmission line was designed and constructed to meet the rapidly increasing power demands of metropolitan areas and supply stable, bulk electric power from the Yonghung thermal power plant into metropolitan areas. This transmission line passes over the west sea, Lake Sihwa and over land. In order to successfully complete this project, and to safely support the tower during severe maritime conditions, several types of tower foundation such as Pad and Chimney foundation, Pier (Cylindrical) foundation, R.C.D foundation, Jacket pile foundation and Steel pipe pile + concrete mat foundation were developed and used. As the world?s first and longest marine transmission line, the 345kV Yonghung marine transmission line operates successfully, thanks to several high-tech civil engineering technologies and KEPCO?s accumulated experience.

Jan 1, 2007

By B. Xu

Keywords: Magnetic damping, g-jitter, Hot-film anemometry Results from an experimental study on natural convection induced by temperature gradient in molten gallium contained inside a rectangular container. The damping effect of the convective flow from an externally applied static magnetic field is investigated. Induced velocity and temperature fields are mapped using a standard constant temperature hot-film anemometry and a thermocouple with and without the applied magnetic field, respectively. Detailed experimental setup and procedure are depicted in the present paper. Obtained velocity and temperature profiles are examined against previous numerical simulations and reasonably good agreement has been achieved. Obvious damping effect can be observed in both the temperature and the velocity profiles when the external magnetic field presents.

Jan 1, 2005

By S. O?Connor

When one looks back and does assessments of what has been the key ingredient in achieving success in our safety efforts, there are many issues that spring to mind and cover a wide array of elements. One does not know which has the ultimate maximum effect. In his presentation yesterday, Alan Peers, our SHEQ leader, covered a lot of detail with the way we are managing safety at Modikwa. I have attempted to identify some of the key essentials in making the mine safe. Passion Safety is addressed with a passion that is unbelievable at times. When I get phoned because an incident has occurred and in reporting the incident, there are already action plans being put in place to prevent re-occurrences, you understand the commitment to put employees? safety first. You hear the disappointment in your subordinates? voices when they have to share the fact that an incident or accident has occurred.

Jan 1, 2011