Search Documents

By R. E. Old

Through the use of pressure and production records, formation properties and bottom-hole sample data, the performance of an oil reservoir may be studied analytically to define and evaluate the natural forces acting on and within the reservoir. Use is made of material-halance methods and the equations for natural water encroachment. to estimate reserves. Methods for calculation of pressures are given. A study of the Jones sand, Schuler field, Arkansas, has been made and is given here to illustrate the value of the methods discussed. Introduction With the decreasing rate of discovery of new oil reserves, attention is necessarily focused on the efficient development, evaluation, and production of existing reserves. From the nation's viewpoint, the necessity of conserving resources is obvious. From the operator's viewpoint, the problem is to lengthen the period of profitable operation, in an attempt to increase the return on his investment. To do this the operator must take advantage of the natural forces acting on and within the reservoir. Natural water encroachment, the nemesis of profitable operation in the past, can be and is being harnessed to produce a greater oil recovery during the stage of flowing production. Proper evaluation of water encroachment rates and a fuller under- standing of reservoir behavior dictate the appropriate production procedures. Complacency in hit and miss production is obsolete. Oil production must and will approach the efficiency of other businesses, such as manufacturing. A manufacturer will not place an article on the market until he has fully investigated the processes involved, additional investment in equipment, costs of production, and expected profits. These may be modified by actual experience at a later date, but at least he begins with an idea of expected return. It is just as logical that an oil operator should investigate these same factors during the development and the early period of production of an oil reserve. The complexity of the problems existing in oil reservoirs should not be underestimated. Conversely, they should not be regarded as insoluble. Many completely defy solution, but there are others that can be solved completely or attacked intelligently to yield approximate results. The petroleum engineer has many tools, both figuratively and literally, at his disposal. Physical data such as core analyses, electrical logs, bottom-hole sample analyses, and bottom-hole pressures are accumulated extensively. Advances in the analytics of fluid flow have kept pace with the advances in measurement of physical data. It is the purpose of this paper to show how some of these records may be analyzed to define certain phases of reservoir behavior.

Jan 1, 1943

By Harry Wolf

The chemistry of the element uranium enables industry to employ either an acid or alkaline carbonate leach solution for most uranium ores. Either method my be used for conventional, in-situ, or heap leaching. Uranium recovery in the leaching process depends both on the solubility of the uranium minerals and, on the access of the leach reagent to them. The uranium leaching rate is proportional to the liberated mineral surface area and the chemical reactions involved in the dissolution step. The dissolution of U(VI) and the oxidation of u(IV) to U(VI) are the basic chemical reactions in the leaching process. The active surface area is a function of the effective porosity and the particle size of the ore (1). Ore pieces, with a high porosity and high permeability, may provide a large active surface area even in coarser fractions. This type of ore might be suitable for heap or in-situ leaching techniques. Nonporous and impervious ores are usually more amenable to conventional milling where the active mineral surface is exposed by grinding the ore down to the liberation size of the mineral.

Jan 1, 1981

By G. M. Dowo

The widespread environmental damage caused by slimes dam construction requires rehabilitation as one of the key management strategies towards land restoration. From the time when Mhangura Copper Mine in Zimbabwe was shut down in 2000 due to viability problems, no follow-up studies were carried out on the slimes dams to assess their development with respect to ecosystem function and longterm recovery. The ecosystem function analysis (EFA) method was thus employed to achieve this end. EFA is a monitoring procedure that establishes how well an ecosystem functions as a biophysical system through the use of rapidly assessed field indicators. The field procedure makes use of simple visual indicators that are related to various soil surface processes. Conventional sampling methods are used to collect the vegetation data. The data was first analysed using landscape function analysis (LFA) software packages and then with various multivariate statistical techniques. In total 27 species were recorded from 14 families; 21 of them occurring in the acacia woodland and only 8 on the slimes dams. Hyparrhenia sp. was the dominant grass on Dam 5 and Imperata cylindrica dominated Dam 6. Acacia saligna was the most abundant tree species on the dams. The tree layer on the slimes dams was not as developed as the grass layer. The rehabilitated slimes dams converged with the natural woodland for the LFA indices of stability, nutrient cycling, and infiltration, which suggested a high level of functionality. The main factors affecting the sustainability of the rehabilitation are postulated to be fire, grazing, and tree harvesting. The study contributed to the importance of, and methods used for, assessing ecosystem function on rehabilitated slimes dams in Zimbabwe, which are often ignored as most efforts focus on the establishment of vegetation on the dams. Keywords ecosystem function analysis, EFA, mine tailings, rehabilitation, monitoring, Mhangura Copper Mine, ecosystem function.

Dec 1, 2013

Since the 1989 Loma Prieta Earthquake in the San Francisco Bay Area, the California Department of Transportation (CALTRANS) has accelerated seismic upgrading of their bridges. Many structures can be improved with the simple addition of hinge seat restrainers. Others require modification of column bents and superstructure to column connections. Often, footing retrofits are necessary, which require the addition of tension/compression elements (compression piling and tiedowns anchors) to resist overturning moments substantially larger than those originally used for footing design. These footing retrofits may include doweled reinforced concrete footing extensions or new pile caps which transmit forces to either driven steel or drilled concrete piles. In some cases, installation of these traditional piling elements is expensive, impractical or impossible due to: low overhead clearance, ground obstructions, high water table, noise or vibration sensitivity, or the inability to laterally expand the existing plan dimensions of the footing. In the latter case, one practical option is to attach small diameter drilled and grouted tension/compression piling elements (Pin Piles) to the existing footing. The footing may be strengthened with dowels and added concrete thickness or there may be a reduced shear span due to the installation of larger or jacketed columns. A reduction of elements is available with a Pin Pile alternative, particularly when the selection of traditional standard piles is governed by the reduced tension/uplift capacity available from the traditional elements, since Pin Piles exhibit superior uplift performance.

Jan 1, 1993

By B. J. Moore

This publication contains routine analyses and related source data for 374 natural gas samples from 24 States and 5 foreign countries. These samples were collected during calendar year 1966 as a part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses of foreign samples contained in this publication represent the first samples received as a result of this expanded program. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4 Eight previous publications have been made to present the results of 7,244 gas analyses made? by the Bureau of Mines Helium Activity prior to 1966. The first three, Bulletins 486,5 576,6 and 617,7 contain analyses and related

Jan 1, 1967

By L Besra, A. R. Prasad, B. P. Singh

The role of surface-chemical phenomena and the physical processes that participate in the dewatering of a suspension of alumina trihydrate were subjected to a systematic investigation, which has increased understanding of the influence of surface tension, contact angle and adsorption in the process. The residual moisture content of the cake can be reduced significantly through the use of surface-active agents in slurry pretreatment or as wash-water additives. The effectiveness of a particular surfactant is hard to predict from any single parameter, but is dependent on its ability to reduce surface tension and possibly to modify the solid-liquid contact angle. If scaled up to industrial operation of the dewatering step of the Bayer process in India, the use of these chemical additives could substantially improve its process economics, reducing the fuel costs for thermal drying by a much as Rs 50/t

Jun 21, 1905

By F. Bruey, T. Bruce, D. R. Nagaraj, W. Thomas, P. Riccio, E. Guitard

"AEROPHINE® 3418A Promoter is a flotation collector that has been an industry standard in the Canadian mineral processing industry since its first commercial use at the Kidd Creek concentrator in 1980. Its wide range of applications in sulphide mineral flotation has made it successful, specifically in the processing of complex sulphide ores which contain copper, lead, zinc, and silver or any combination of these elements for selective separation.AEROPHINE® 3418A Promoter is a unique, phosphine-based collector originally developed for the flotation of copper sulphide minerals and activated zinc minerals. It is now recognized for its selectivity for complex, polymetallic sulphide ores and porphyry copper ores. In addition, AEROPHINE® 3418A Promoter is highly selective for copper, lead, activated zinc, nickel and precious metals. AEROPHINE® 3418A Promoter exhibits strength yet, selectivity against iron sulphides (pyrite, pyrrhotite, marcasite, and arsenopyrite), non-activated sphalerite, and many minerals which contain penalty elements.This paper outlines a brief history of the product’s development, its historical use in Canada and several potential innovative mineral processing applications with the use of the chemistry. Three Canadian case studies will be presented on various ore types including: a Cu-Au ore, a Cu-Zn ore, and Cu-Pb-Zn ore. A plant production update will also be given on the future supply of AEROPHINE® 3418A Promoter.INTRODUCTIONCytec Industries Inc. operates a phosphine derivatives plant in Niagara Falls, Ontario, that manufactures various products for their speciality chemicals division. The products from this site are based on phosphine (PH3) chemistry and are used in a variety of markets including electronics, agriculture, LED lighting, water treatment, metal extraction, and mineral processing. One of the major products is the phosphine-based sulphide mineral collector, AEROPHINE® 3418A Promoter.AEROPHINE® 3418A Promoter (Figure 1) was originally developed for the flotation of copper and activated zinc minerals (Thomas, 2010).."

Jan 1, 2015

By John H. Gasper

The success of steep slope (>20°) contour mining depends on many factors. Most important is the selection of the mining method that best suits the premining site conditions environmentally and economically. These conditions can be divided into three categories: • Geometric conditions - machine limitations, slope stability restrictions, erosion capacity; • Physical conditions - material properties, rock strengths, ability to dig, driving surfaces; and • Chemical conditions - acid-base relationships, blending or selective placement of overburden. This article incorporates these conditions by conceptually modeling compliance-oriented contour mining methods, particularly haulback methods, using the combined front-end loader (FEL)/ truck, tractor/scraper, and FEL-truck and scraper. Engineering analyses, including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces) and drainage requirements can be performed after the geometric constraints dictated by in situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized, three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple, two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By David C. Kraft

Helical piles and ground anchors were used to meet critical design and constructability requirements for an urban forest Canopy Walk at the Atlanta Botanical Garden, Atlanta, GA. The 12-foot wide pedestrian walkway path was to be nestled among the treetops of a forest, extending to 600 ft. in length, and soaring 40 ft. high above the forest floor. Of particular concern during construction was that the foundation system for the temporary steel shoring system had to be non-invasive to the subsoil, could not damage the forest floor, trees, root systems, or foliage, and upon completion of the concrete walkway pour, could be removed, again without disturbing the subsoil. Accubrace, Inc. designed and installed all the helical foundation types, as well as provided steel braces, typically used in Tilt-Up building construction, for the walkway project. The braces, some extending to 43 ft. in length, were used to provide lateral support against wind loads for the walkway form. In addition, the braces acted as secondary support for lateral loads during the placement of wet concrete along the 600 ft. length of the walkway. Helical foundation products installed included vertical compression piles, ground anchors for tension rods, and ground anchors for the braces. The installation of the piles and anchors was particularly challenging since the forest floor elevation varied as much as 50 ft. due to the presence of a ravine. Information is provided on the subsoil conditions, required loads, design, installation, and acceptance criteria for each helical product type installed for the project. The results of vertical and lateral load tests on the helical piles in the pre-construction phase, conducted in conformance to project specifications are presented. Photographs to illustrate the nature and complexity of the project are included. The concrete pour for the walkway was successfully completed on December 12, 2009, and the walkway was opened for visitors in May, 2010.

Jan 1, 2011

By Eric H. Brown

One of the best methods by which the results of accident-prevention work can be measured for any particular period is to keep an accurate record of the accident experience, which may then also be compared with the experience of others. The purpose of this report is to compare records of the salt-mining companies operating in Louisiana, and their assistance in making available their accident records is gratefully acknowledged. PRODUCTION Four companies produce salt in Louisiana -Avery Salt Co., Avery Island; Jefferson Island Salt Mining Co., Jefferson Island; Myles Salt Co., Weeks; and Carey Salt Co., Winnfield. Three of these companies operate within 30 miles of each other in the southern part of the State, and the other operates in the central part.

Jan 1, 1938

By Bruce Jago, Joe Zhou, Chris Martin

"From the perspective of metallurgical processing, gold ores can be classified into free-milling and refractory ores. Their extractive metallurgy are largely driven by mineralogical factors such as: gold particle size, association with other minerals, coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of refractory gold minerals and locking of submicroscopic gold in sulfide mineral structure etc. Gold process mineralogy helps address issues and problems related to gold ore processing. It provides useful information on process selection, flowsheet development, recovery improvement and reagent consumption optimization. By combining classic mineralogical techniques, modern instrumental analysis and diagnostic metallurgy, the mineralogist is able to balance the various types of gold occurrence in an ore. This paper will provide a broad review of gold process mineralogy and the techniques available, and use case studies to describe how they can be used together, to provide the complete picture of gold process mineralogy in an ore. Examples will be used where applicable.INTRODUCTIONSince the early 1980’s, a great deal of work has been done in the characterization of gold ores, particularly refractory ores (Gasparrini, 1983; Wang, 1984; Hausen, 1985; Haines, 1986; Henley, 1989; Chryssoulis et al., 1990; Wang et al., 1992, 1994; Kojonen, 1999; Simon et al., 1999; Hong et al., 2000; Pals et al, 2003). Process mineralogy has come into its own as a respected inter-discipline in the fields of mineralogy and metallurgy – a subject that occupies an important place in both research and industry. As the free-milling gold ores are being depleted and more refractory ores are being discovered and processed, gold process mineralogy receives more and more attention from both the mineralogist and metallurgist as it helps to solve various problems encountered during gold ore processing. Steadily rising gold prices are also stimulating the need for gold process mineralogy due to the increasing demand for and production of the yellow metal. At SGS Lakefield Research, gold process mineralogy studies are conducted routinely on all types of gold ores and mill products to assist in a wide variety of metallurgical projects. This paper will briefly discuss the gold ore types and gold mineralogy, review the common mineralogical factors affecting gold extractive metallurgy and the techniques available to gold process mineralogy, introduce the procedure employed at SGS Lakefield Researc"

Jan 1, 2004

By D. Fray

Electrochemical processing using molten electrolytes is undergoing a considerable renaissance due to several innovative ideas being explored both in the laboratory and also at the pilot scale. Several of these new ideas are related to developments in energy generation and storage and involve solid electrolytes. Sodium has been prepared by the electrolysis of sodium carbonate or sodium hydroxide with the transfer of sodium ions through a sodium beta" alumina membrane and magnesium oxide dissociated by the removal of the oxygen through a stabilized zirconiaelectrolyte incorporating a fuel cell electrode. By using halides with highly electropositive cations, such as molten calcium chloride, it has been found that the favoured cathodic reaction, when oxygen is present, is the ionization of oxygen and not the deposition of calcium. This approach has been applied to the reduction of many metal oxides including titanium, zirconium, niobium and rare earth oxides and, by using a mixture of oxides as the cathode, homogeneous alloys are produced. This concept can also be applied to deoxidation of solid and liquid metals. Refining of metals is possible using intercalation compounds and, in a completely different application, it has-been found that, by intercalating alkali metals by electrolysis of alkali halides into graphite, it is possible to produce carbon nanotubes and nanoparticles. The technological opportunities of these various concepts will be discussed.

Jan 1, 2004

By Peter Campi, Harry R. Asche, Ian P. Callow, Edmund G. Taylor, P. Scott Smith

The US$1,850 million EastLink project is a 39km tollway and includes twin 3-lane,1.5km long, undrained driven tunnels. The hard rock tunnels are being built to avoid passing the motorway through the Mullum Mullum Valley and so to help preserve the unique flora and fauna in the area. This paper describes several of the key issues in the tunnel design and construction, including: the integration of the temporary support design with the Contractor’s tunnel excavation and support procedures, including sharing of responsibility between the Designer and Contractor for support type selection and the production of a project specific rock mass classification system to enable more objective determination of ground conditions. detailed hydrogeological assessments during the design and construction phases to allow confirmation of design loads for the tunnel lining design and the various suite of waterproofing tools in order to meet the project inflow requirements. development of a pre-cast invert solution to the main tunnel secondary lining to enable faster lining construction and to minimize risks to the tunnel membrane associated with fixing reinforcement and construction traffic.

Jan 1, 2007

By A. Ploszajski

This item examines the history and uses of tungsten, from discovery to superalloys via the lightbulb and electron beam instruments.

Apr 1, 2015

By Neyer David Cerna Flores

El desarrollo de proyectos mineros en espacios geográficos con históricos pasivos ambientales conlleva en la población un imaginario de contaminación extrema y consecuencias graves para la salud y el deterioro de su hábitat presente trabajo. Es este contexto Antamina desarrolla mecanismos alternativos para el manejo de los conflictos socioambientales de su entorno, los cuales buscan generar confianza entre las partes, disminuir los conflictos socioambientales y explorar conjuntamente propuestas de crecimiento y desarrollo sostenible. Por ello, el presente trabajo describe la experiencia realiza, donde los mecanismos utilizadoss basan su accionar en la atención de las preocupaciones, necesidades, intereses y concepciones de los grupos de interés sobre el desempeño ambiental de Antamina.

Sep 9, 2007

By Axel Studeny

Geomechanical-numerical methods are an established tool for planning of underground excavations worldwide. By describing the interaction between heterogeneous layered strata and support elements it is possible to determine their suitability. The German hard coal mining industry has more than twenty years experience in investigation and using these parameters to carry out numerical calculations. Today, nearly all excavations (shafts, pit bottoms areas, bunkers, coal faces, development drivages, gate roads etc.) are calculated by geomechanical-numerical tools in combination with empirical planning methods. A high accuracy of planning results, which is a special requirement in the German coal industry with its deep-level longwalls, bedded and weak surrounding strata and multiple seam mining layouts, depends on the extensive calibration of the numerical models, which is achieved by: 1) Taking a large number of underground measurements with empirical evaluation. 2) Carrying out physical modeling. 3) Using the characteristic features of the installed support elements. This paper compares the planning approach used for multiple and single seam mining and presents the advantages of this planning tool. The main focus is on the feasibility of rockbolting as the sole means of roadway support for multiple seam mining operations, though the paper will also look at how the costs can be improved by using a low bolting density in single seam layouts.

Jan 1, 2007

By Dale S. Preece

"The computer program DMC (Distinct Motion Code) [Taylor and Preece, 1989a] was developed in 1988 and 1989 to predict the motion of rock following a conventional blast. DMC executes very efficiently on a CRAY type computer due to the high degree of vectorization and also due to the use of spherical elements [TayIor and Preece, 1989b]. Bulking mechanisms developed specifically for use with spherical elements include rotation-induced dilatation and aspect ratio > 1.0 [Preece and Taylor, 19901. Rotation-induced dilatation allows the radius of the sphere to expand as a function ofsphere rotation to simulate the interaction of corners and sides of blocky rocks. An aspect ratio > 1.0 is achieved by kinematically tieing spheres together."

Jan 1, 1991

By A. Sinha, N. K. Babar, H. R. Kalihari, A. K. Chakraborty, M. R. Saharan, C. P. N. Pathak

A case study is presented on the optimization of cable bolting patterns in cut-and-fill stopes at the Chikla Mine, MOIL, India. Rock mass characterization, using Bieniawski’s RMR and Barton’s Q, indicated that the stopes lie in the “no supports required” to “spot bolting required” support categories. In contrast, the current practice of cable bolting in a 2.0 m by 2.0 m grid pattern for stope widths less than 12 m displays different results. Numerical modelling results are in line with the rock mass characterization study. It can be affirmed, as well, that no cable is carrying rock loads greater than 5 t. This fact is derived from observational behaviour of the crown pillar of an experimental stope with open stoping operations and hanging cables in the cut-and-fill stopes of the mine. An increase in the cable bolting grid spacing is, hence, recommended for implementation by mine management, based on the study described in subsequent sections. It is also suggested that the mine adopt the open stoping method, provided results of a rock mechanics instrumentation program in an experimental stope with a cable bolting grid of 2.5 m square are favourable.

Jan 1, 2007

By C. T. Baroch

CESIUM-137 ISOTOPE began to displace cobalt-60 III the treatment of cancer during 1956. Production and Consumption.-Consumption of cesium and rubidium was approximately the same as in 1955. Production, however, decreased, as several companies shipped from stocks produced in previous years. South Africa was the source of most cesium and rubidium minerals used in the United States in 1956. Cesium and rubidium metals and compounds were produced from ore by: DeRewal International Rare Metals Co., Philadelphia, Pa.; Fairmont Chemical Co., Inc., Newark, N. J.; Foote Mineral Co., Philadelphia, Pa.; and Rocky Mountain Research, Inc., Denver, Colo. Most sales were to domestic consumers, but small quantities were exported to Australia, England, Germany, and Sweden. New production facilities were under construction in. 1956 by San Antonio Chemicals to produce mixed potassium, rubidium, and cesium carbonates. A plant capable of separating and packaging 200,000 curies of cesium-137 annually was under construction at Oak Ridge National Laboratory.6

Jan 1, 1958

By Rocky (Yaokun) Wu

This paper introduces the development and application of a new cable anchor - Cable-Lok for pre-stressed cable bolting in mines. Cable-Lok is a spring-loaded cable anchor suitable for the drill hole diameter of 50 and 65 mm (2" and 2.5") in medium soft rock to hard rocks. The cable anchor is automatically set on installation and the cable can be tensioned immediately to provide active and primary support throughout its length. Post-grouting can be conducted independently. In comparison with the conventional cable bolting, Cable-Lok anchor will greatly speed-up the cable bolting circle and decreases the cost of cable bolting. Cable bolting anchored with Cable-Lok anchor has wide application in mines, e.g. pre-stressed cable bolting in large span drifts and intersections for permanent rock support, or in hanging walls or stopes for temporary support, or cable lace anchoring etc. This paper introduces the principle of pre-stressed cable bolting and the specifications of the Cable-Lok anchor, presented the testing results in laboratory and the application cases in mines.

Oct 1, 2010