Search Documents

By Walter W. Kaufman

This Bureau of Mines manual for design of surface mine haulage roads covers such aspects of haulage road design as road alinement (both vertical and horizontal), construction materials, cross slope, and drainage provisions. Traffic control and design of proper lane widths to promote safe vehicle movement are included, as are suggested criteria for road and vehicle maintenance and for runaway-vehicle safety provisions. The aim of this publication is to provide those involved with surface mine haulage road design with a complete manual of recommended practices that, if implemented, will promote safer, more efficient haulage routes.

Jan 1, 1977

By S. K. Bradford

(Pittsburg Meeting, March, 1910.) FOR years past I have traveled in quest of promising mining-properties, over almost impassable mountain-trails to remote places in the mining-regions, usually, many miles from an assay-office. If, upon examination, the formation and the ore-deposit appeared favorable, a quick determination of the value of my samples was necessary, in order that I might take intelligent action with reference to the acquisition of the property. A journey with my samples to civilized regions often meant weeks of delay, and perhaps loss of opportunity. How many, under similar circumstances, have returned with their assay-results from such a journey, only to find that some audacious speculator had " optioned" the property ! True, a first payment could have been made and the chances taken on the results; but experience has taught that rich-looking ore is not of necessity valuable. Personally, I would not hazard a ten-dollar bill on any property without first determining by assay the value of the ore. To carry the usual complete assay-paraphernalia over such mountain-trails was impracticable by reason of the loss of time involved, the great expense of transportation (charged according to weight), and the fact that a few such trips would almost certainly wreck the outfit. For these reasons I began a process of elimination and substitution which finally enabled me to carry, in an ordinary 26-in. valise, sufficient apparatus and supplies for, say, 100 assays of adequate commercial accuracy. My final outfit was as follows: APPARATUS. Small hammer; steel mortar (2.5 in. wide, 3 in. high, with stand sawed off flat, so that it can be used as an anvil and for

Jan 1, 1911

By R. J. Leary

This investigation was conducted to determine the effects of various rare-earth metal addition practices upon the macrostructure and the pattern of sulfur distribution in steel ingots. Heats of plain carbon steel were melted in a 1-ton, basic electric-arc furnace. Melts were treated with mixtures of rare-earth silicides, aluminum, and cryolite either in the furnace before tap or in the ladle after tap to determine the effects of this form of rare-earth treatment upon ingot macrostructure. Steels thus treated with rare earths in the furnace were characteristically free of the gross subsurface nonmetallics which typically result from conventional rare-earth treatments. Steel treated in the ladle showed only a few such nonmetallics, and practical techniques were developed for eliminating most of these. Results showed that furnace deoxidation was controlled by the concentration ratio of rare earths: aluminum. During casting, deoxidation was controlled by the concentration of rare earths. Oxygen contents equivalent to vacuum ladle degassing resulted from air-melt furnace treatments with the rare-earth mixtures described. Rare earths in steel inhibited the onset of equiaxed grain formation during ingot freezing, and also virtually prevented interdendritic segregation of sulfides.

Jan 1, 1968

By Stavros H. Constantopoulos

Mediterranean regions such as Greece, Turkey, Cyprus, Corsica and New Caledonia have experienced epidemics of malignant mesothelioma as a result of non-occupational, ??domestic?? exposure to tremolite asbestos and fibrous erionite. This exposure to tremolite asbestos and fibrous erionite is typified ??domestic?? due to its prevalence in regions with natural deposits of tremolite asbestos (or fibrous erionite) where the material from tremolite asbestos or fibrous erionite is used for domestic applications such as whitewashing. However, these exposures may be useful in examining the potential consequences of even small amounts of amphibole asbestos fibers in the ambient air. It can also elucidate the effects of fibers that behave like amphibole asbestos. However, this type of exposure is not useful for studying the potential effects of small amounts of asbestos in the ambient air of big cities due to the differing nature of the fiber types and modes of exposure between the regions. © 2008 Published by Elsevier Inc. Keywords: Tremolite asbestos; Erionite; Domestic; Environmental; Exposure

Jan 1, 2007

By F. Pinto, J. V. Lemos, A. Sousa, L. Ribeiro e Sousa

The Rossio railway tunnel was built in 1890 crossing several formations involving limestones, basalts and also sandy and clayey formations. Due to the fact that it is an old underground structure rehabilitation and repair works were performed, namely at Km 0,900 and in a zone crossed by a new tunnel from the Lisbon Metro. Reinforcement support systems were designed in the Rossio tunnel in order to prevent its stability. In this paper, repair works and anchor tests performed at km 0,900 are presented, as well as the monitoring system implemented in order to observe the structural effects induced by the construction of the works. For the interpretation of the obtained information complex 3D models was built, permitting the simulation of the sequential excavation scheme used, non-linear behaviour of the different formations, and the support systems used. Der 1890 erbaute Rossio Eisenbahntunnel durchoertert mehrere Formationen, einschliesslich einer Kalkstein-, Basalt- sowie einer sandigen und tonigen Formation. Auf Grund des Alters des unterirdischen Bauwerks wurden Instandsetzungs- und Reparaturarbeiten im Bereich km 0,900 sowie im Kreuzungsbereich mit einem neuen Tunnel der Lissabonner U-Bahn durchgeführt. Aussteifungssysteme wurden entworfen, um die Stabilität des Rossio Tunnels zu gewährleisten. Im Folgenden werden die Instandsetzungsarbeiten und Anker Tests im Bereich km 0,900 sowie das Messystem zur Ueberwachung der strukturellen Auswirkungen der Bauarbeiten dargestellt. Zur Interpretation der gewonnenen Informationen wurden komplexe 3D Modelle entwickelt, die eine Simulation des Bauablaufs und die Anwendung nichtlinearer Stoffgesetze fuer die verschiedenen Formationen und Aussteifungssysteme ermöglichten. Le Tunnel ferroviaire du Rossio a été construit en 1890, traversant des différents terrains comme des calcaires, des basaltes et aussi des formations limoneuses et sableuses. Dû à l’ancienneté de l’ouvrage, des travaux de réhabilitation et réparation ont été faits, nomment au km 0,900 et dans la zone traversée par le nouveau tunnel du Metro de Lisbonne. Des systèmes de support renforcé ont été conçus pour le Tunnel du Rossio de façon à rassurer sa stabilité. Dans ce papier, on présente les travaux de réparation et les essais d’ancrage réalisés au km 0,900, et aussi, le système d’auscultation mise au point pour l’observation des effets structuraux induits par les travaux. De façon à interpréter l’information résultant de l’observation, des modèles 3D complexes ont été utilisés, permettant la simulation de la méthode séquentielle de l’excavation, du comportement non - linéaire du terrain et, aussi les systèmes de support utilisés.

Jan 1, 2003

By Grant Buma

Groundwater restoration is an uranium leaching. Information on the technology, costs, and the current permitting regulations is of vital operators and to firms considering in important aspect of in situ effectiveness of the current state and federal government importance to in situ leach situ leaching. This study, funded by the U. S. Bureau of Mines, describes: (1) all recent restoration attempts at commercial in situ leach operations, (2) restoration costs reported by the industry, (3) empirical equations that predict the amount of groundwater flushing required to meet the current restoration criteria, and (4) in situ uranium permit requirements for the states of Texas, Wyoming, New Mexico, Utah, Montana, Colorado and South Dakota, and Federal requirements.

Jan 1, 1981

The case study has identified and characterised additional subsidence arising from longwall mining above or under existing longwall goaf. It suggests that the magnitude, mechanisms and prediction methods for such additional subsidence are different between the two mining configurations. This paper presents a proposed method to predict maximum vertical subsidence due to longwall mining under existing longwall goaf. It suggests that, unless different results from further new cases become available, the findings presented in this article, including the aforementioned prediction method, be applicable to the majority of sites in New South Wales, where multi-seam longwall mining is to take place. This article also presents an important concept of 'overburden modification' due to multi-seam mining. A causal relationship between the above-mentioned additional subsidence and 'overburden modification' has been identified as a result of the case studies. Further investigations into the physical processes that cause such overburden modification will be fundamental to the understanding and management of multi-seam subsidence.

Nov 25, 2010

By John E. Conley

The need for lightweight aggregate for use in concrete products ,and structures has caused the Bureau of Mines to undertake an investigation to determine the availability of suitable raw materials and to study methods, procedures, and equipment to supply that need. Evidence is at hand to prove that the shortage of lightweight aggregate is nationwide. A survey recently covered in a report (13)5/ by the Construction Branch of the National Housing Agency has pointed out the locations in which lightweight aggregates are produced. A study of this information discloses that the producing centers are widespread, and that certain areas, notably the region east of the Mississippi River, and especially the sections along the Atlantic coast line and the Southeastern States, have only a few such plants. Certainly, many localities are badly in need of installations equipped to provide an ample supply of high-grade lightweight aggregate. The work undertaken by the Bureau of Mines includes investigation of the use of clays, shales, slate wastes, coal-mine wastes, diatomite-clay combinations, and various other 'mineral mixtures as possible raw materials. Likewise, special consideration has been given to the development' of equipment and techniques to produce the lightweight products.

Jan 1, 1949

By H. K. VAN POOLLEEN, W. Hurst, H. C. Bixel

In an earlier publication* I showed the development of the instantaneous point source solution for a well producing at a constant rate at the center of a system of two radial, adjoining sands of different permeabilities. I also showed how a wellbore radius could be incorporated if this were the development required. For the purpose of that paper and the point I wished to make, this solution served. It yielded a simplifying solution of sands in series identified by Eqs. VI-26 and VI-27. (These equations are reproduced in part by Bixel and van Poollen as their Eq. 3, Page 302.) I am well aware that the simplified solutions are approximations. The facts that these Ei-functions satisfy the diffusivity equation and meet the boundary conditions both at the well and at the interface between sands, and that the earliest time considerations yield zero pressure drop, are evidence that the solutions are good approximations. This was the purpose for these formulas, which I interpret that where the permeabilities are of finite order of magnitudes in the respective media, the relations give satisfactory answers. However, from the authors' point of view there are reservations, which leads me to consider their entire generalization as illustrated in their Figs. 1 through 14. What I understand from their storage capacity, relationship Fs, which is the ratio of the product of porosity and compressibility of Sand II to Sand I, that is employed here by the authors as a correlative means of identifying one figure from another, there is nothing in the exact mathematics that supports such a term as a means of correlation. This is taken out of context, unsustained that this applies. Here the mathematics are known, where the true correlation is the diffusivity term of one sand to another. This entails permeability that refers back again to the term M in their paper for the transmis-sibility of fluid from one sand to the other that should have also been a part of this storage capacity. In Figs. 8 through 14, which purported to show the simplified equation following this correlation, there are apparent discontinuities for M equal to or less than 0.1000 that differ from the trends for greater values of M. In this connection there is no reference radius given for this cumulative pressure drop in the paper that would permit me to make these calculations. However, what is clear for M equal to 0.1000 or less we are treated to almost a closed barrier at the interface; a condition entered by the writers without qualification. This across-the-board treatment of these simplified formulas, whatever the motive of the authors, enters into a range of permeabilities that even I as the contributor would have reservations that such could apply. Under comparable conditions I would be looking at a closed reservoir or some facsimile for such. The extent to which the approximation or the exact equations pertain is not evident in the generality offered by Bixel and van Poollen in their paper. Only when they or other writers show the comparison of the pressure distributions within the formations can one be able to judge the rational limits to subscribe to the simplified formulas.

Jan 1, 1969

By Joshua Micah Hoffman, Jhon Silva-Castro, Kylie Larson-Robl

A coal mine impoundment failure has the potential to be environmentally devastating and life-threatening. It is well documented that after seismic events slope failures in impoundments can occur. It has been concluded that often the main driven factor of the failure is the increase in excess pore pressure due to ground vibration. A small amount of research has been done regarding the stability of coal mine impoundments under natural seismic events; however no research has been done considering vibrations from mine blasts. If it is taken into account that current environmental restrictions oblige to increase the capacity of coal mine impoundments, thus increasing the hazard of such structures, it is necessary to evaluate the effects of near-by mine blasting on the stability of the coal mine impoundments in order to mitigate and control the potential of slope failures. To study the behavior of excess pore pressure under blasting conditions, scaled simulations of production blasting events were set up inside of a controlled sand tank. The research was divided in two stages. The first one was done, using dry conditions, while in the second part, the same set of tests were performed under saturated conditions. This document shows the partial results for stage one (dry conditions). For the tests, explosive charges were set off within the sand tank at various distances to simulate different blasting distances. Information was collected from geophones, accelerometers, microphones and high speed video camera for dry and saturated scenarios and additionally from piezometers under saturated conditions to assess the behavior of the material under blasting conditions.

Jan 1, 2015

The objectives of this paper are to introduce the International Code of Practice for Risk Management of Tunnel Works and to illustrate to the participants of the 13th Australian Tunnelling Conference 2008 how the insurance industry would like to see the future of tunnelling insurance. Tunnel construction projects have suffered large losses over the years as can be shown from various loss examples and a list of major losses over the last ten to 15 years. Since the consequences of insufficient risk control had to be borne by insurers, these losses have heightened the need for improved and adequate risk management measures so that insurance cover can also in future be provided for this hazardous industry sector. Observations are made as regards to the prevailing trends in the tunnelling industry, which contribute to the increase in risk and have adverse consequences for the insurance industry. To find a solution to this dilemma various options are examined with the suggestion of a Joint Code of Practice for Tunnel Works being agreed by all stakeholders, which would become essential to secure future insurance protection for such project work. The British Tunnelling Society has, in cooperation with the Association of British Insurers, developed such a code, which the International Tunnelling Insurance Group has now adopted for global application in international markets. The content and concept of this code is explained to establish a framework of understanding and applied risk management principles for tunnel works. This initiative also has the support of the International Tunnelling Association and the International Association of Engineering Insurers. The international application of this new code is demonstrated with a few examples, which also includes Australian projects. It is the aim that this code forms in future part of the insurance coverage for tunnelling works in order to put this risk segment on a more sustainable basis. For that reason the insurance industry is seeking the support of all stakeholders of tunnelling construction projects.

Jan 1, 2008

By Wittenberg J. C, Reid A. F

A method is described for the rapid and effective production of polished section mounts of ore and mineral particulates to the standards required for automated image analysis. This requires mounting without segregation of particles by mass or density, and it is also preferable to avoid having particles in contact so that they can be recognised as individuals. To achieve this, the particle samples are first split to an appropriate degree in a rotary riffle, and the sub-sample mechanically diluted and thoroughly mixed with an inert filler of the same size range as the particles. Just sufficient epoxy resin is added to make the mixture fluid. During setting, the ore particles are mechanically supported by the inert filler particles, thus maintaining the particles in a random three-dimensional distribution. A rapid two-stage grinding process, based on the successive use of 600 mesh silicon carbide and 1200 mesh (10 um) corundum on cast iron plates, is followed by three stages of mechanical diamond polishing on cloth laps. Hand polishing is entirely avoided, as is the use of papers.

Jan 1, 1984

By J. F. Stenebråten, W. P. Johnson, D. R. Brosnahan

Carbonaceous material (CM) from ores of varying preg-robbing activity from Barrick Goldstrike Mines Inc. (BGMI), Nevada, was characterized in terms of its functional group content, hydrocarbon content, elemental composition, and humic acid content. FT-IR analyses showed neither the presence of hydrocarbons nor of carboxylic, phenolic, or sulfhydrol functionalities. FT-IR bands present included C=C stretching in aromatic rings and C-O-C stretching, indicating presence of oxygen as ether linkages in the carbon matrix. Calculated atomic oxygen to carbon (O/C) ratios did not reveal a trend between maturity of CM and preg-robbing behavior, possibly due to low resolution of electron microprobe analysis. However, the atomic O/C ratios agree with other chemical analysis, indicating that the organic carbon is very mature, similar to or higher in grade than anthracite coal.

Jan 1, 1999

By J. J. Gusek

Several final pits in the Seneca No. 1 Surface Coal Mine were abandoned in the 1960's without king reclaimed. In addition, a progressive landslide aggravated by the abandoned mine land conditions was threatening a county mad and private property. An AML-funded project to stabilize the landslide and reclaim the final pits was completed in 1986 for the Colorado Division of Mines and Geology (formerly Colorado Mine Land Reclamation Division). The site was visited after ten growing seasons. The land is stable and the vegetation re-establishment is strong. Volunteer native plant species are now invading the reclaimed sites.

Feb 24, 1997

By B. F. Giyani, A. Salama

Tanzania is a country with a variety of mineral deposits, including metallic minerals, gemstones, mineral fuels, industrial minerals, and critical minerals. This study provides an overview of mining legal framework, mineral occurrence and production, challenges in the mining sector, and government initiatives. The aim is to demonstrate the development of the mining sector in Tanzania and explore the potential for further mining investment in the country. The mineral production data showed generally increasing trends over the years, for example, gold production increased from 42 tonnes in 2018/2019 to around 50 tonnes in 2023/2024. Despite the growth, the mining sector encounters several challenges, including a lack of detailed geological information on mineral deposits, inadequate infrastructures in some remote mining sites, the existence of informal artisanal miners, and mineral smuggling. The Tanzanian government has introduced several initiatives to address these challenges, including carrying out the highresolution airborne geophysical survey to increase geological information in some areas, the formalisation of artisanal and small-scale mining, establishing mineral markets to combat mineral smuggling, and encouraging mineral value addition within the country.

Oct 24, 2025

By B. H. Moore

Foundation and excavation problems associated with lock construction projects vary widely. Each lock requires a different foundation to respond to a unique geologic setting. The range of heights and founding materials are illustrated thru description of selected structures encountered in the United States. Examples range from 113-ft high John Day Lock on the Columbia River founded on basalt rock to the 17-ft high Lock No. 5 on the Arkansas River floated on a clay foundation. A description of the basic elements of design and construction is presented. Several case histories involving lock design and construction are assessed to aid in recognition of potential problem areas on forthcoming construction. In the past decade there have been many improvements in construction materials and techniques. The application of these new approaches to lock construction is discussed.

Jan 1, 2010

By F. A. Rutledge

The Batesville district in north central Arkansas is one of the important sources of manganese ore and ferruginous manganese ore in the United States, with a history of production dating back to 1849. From studies by the Federal Geological Survey, it was recognized that the district probably still contains substantial reserves of low-grade ore. It was natural, therefore, that the deposits in this area should be among the first investigated by the Bureau of Mines under the Strategic Materials Act of June 1939, by which the Bureau was authorized to explore domestic deposits of strategic minerals, at that time designated as those of antimony, chromium, manganese, mercury, nickel, tin, and tungsten. The field work of the Bureau of Mines in the Batesville district was done in two distinct phases. Under project 308, active from August 1940 to June 1941, carbonate-oxide ores were investigated at five separate areas in which 100 trenches, test pits, shafts, and edits aggregating 4,364 linear feet were excavated and 839 samples were taken and assayed. Under project 323, in progress from February 1941 to January 1942, wad deposits were explored at 10 separate areas by 408 prospect shafts, churn-drill holes, and bucket-drill holes aggregating 23,680 linear feet from which 285 samples were taken and assayed. Processes for beneficiating the wad ores were investigated at ore-testing laboratories of the Bureau of Mines.

Jan 1, 1952

By R. S. Dean

[During the past year the Metallurgical Fundamentals Section gave about an equal amount of time to the experimental determination of fundamental thermodynamic constants and to the demonstration of the application of such data to more directly practical metallurgical problems. The first division of the work - the actual experimental measurements of typical thermodynamic constants - was carried out an two problems, termed ?continuing? programs, namely, (1) measurements of Specific Heats at Low Temperatures and (2) Measurements of Heats of Formation and Free Energies. Specific substances chosen for investigation are classified as (n) those that have been the subject of requests for information from the industry and that, upon examination, seem of sufficient practical importance to justify study, and (b) compounds that are difficult to treat metallurgically, or whose specific thermodynamic properties have not yet been determined satisfactorily and for which accurate data might suggest improved or new methods of Metallurgical treatment, or (c) materials recognized as belonging to a social class with exceptional thermodynamic properties and, hence, of scientific as well as technical importance.]

Jan 1, 1938

By Sidney Katell

This study estimates capital investment, operating costs, and selling prices for four underground bituminous mines producing coal with annual production ranging from 1.06 to 4.99 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of November 12, 1973, under the Bituminous Wage Agreement of 1971, and costs for material and equipment are based on 1973 indexes. Initial capital investment ranges from $12,540,700 for the 1.06-million-ton-per-year (MM tpy) mine to $44,720,500 for the 4.99 MM tpy mine. Total capital investment ranges from $21,850,700 to $75,693,500 for the same mines. Corresponding selling prices for the coal range from $8.76 to $7.53 per ton, assuming a 12-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1974

By R. Mark, R. Richards

The Washington National Cathedral is one of the largest masonry structures in the USA, and like many of its European Gothic counterparts, it required nearly a century to construct. The design was altered during this period, resulting in greater loadings than were originally anticipated on the soil beneath the foundation. When signs of continuing differential settlement were observed in the early 1990's, the Cathedral approached the US Bureau of Mines (now the National Institute for Occupational Safety and Health (NIOSH)) for assistance in monitoring the movements of the massive towers and walls. An array of dual-axis tiltmeters was installed about 40m above ground level to measure wall and tower inclination, with the data sent over a dedicated phone line to the NIOSH Pittsburgh Research Laboratory for processing. Mechanical gages and string-potentiometers are also being used to measure motion across cracks and joints, and differential pier settlement is being monitored with optical-level surveying. Data have now been collected for almost 7 years, and they show a long-term settlement trend masked by dramatic diurnal and seasonal thermal movements. The paper discusses the major findings of the study, implications for the future of the Cathedral, and conclusions regarding the use of geotechnical monitoring at major national monuments.