Search Documents

By Wellington Pereira Inácio, Fernando Wypych, Sergio Neves Monteiro, Artur Camposo Pereira, Rafael Marangoni

"The efficiency by which an applied load is transmitted from the matrix to reinforcing fibers in a composite depends on the fiber/matrix adhesion strength. This is determined as the interfacial shear strength, IFSS, which may be measured by means of pullout tests that measure the force needed to pull a single fiber out of a block of material simulating the composite matrix. Different techniques are used to perform pullout tests. The objective of this work was to characterize the IFSS of sisal fibers embedded in epoxy matrix through the determination of the critical length pullout curves. As the main results, a relatively small critical length was found for the sisal fiber/epoxy pullout specimens, corresponding to a weaker IFSS. This was compared to other results applying different pullout techniques. Scanning electron microscopy observation identified the mechanism responsible for the weak sisal fiber adhesion to the epoxy matrix.IntroductionSynthetic fiber reinforced composites is today one of the most successful class of materials with increasing industrial applications from house appliances to large airplanes like the modem Airbus 380. However, environmental issues are revealing serious drawbacks related to the fabrication, use and post-use discard of these composites. For instance, the thermoset polymer composite reinforced with E-glass fiber, known as ""fiberglass"" has an energy-intensive fabrication associated with a surplus emission of C02, which is responsible for global warming [1]. Moreover, the glass fiber is considered toxic and also causes long term pollution after being discarded."

Jan 1, 2011

By Jean P. Murray

The extractive metallurgical industry is a major consumer of high-temperature process heat. It is, consequently, a major contributor of C02 emissions and other greenhouse gases derived from the combustion of fossil fuels for heat and electricity generation, or from the process itself. These emissions can be substantially reduced by replacing fossil fuels with solar energy as the source of process heat. Concentrated solar radiation can supply a large amount of thermal energy to endothermic reactions at temperatures exceeding 2000 K. Another potential for C02 emission reduction exists as well. Thermodynamically, the total amount of energy required for metal production at any given temperature is the enthalpy change of the reaction, AH. Of this total, an amount equal to the Gibbs free energy AG must be supplied as high quality energy in the form of electrical work or by using a reducing agent. Many conventional metallurgical electrolytic processes and reducing furnaces are unable to add only the thermodynamically required electricaVchemical energy due to process inefficiencies. Electrical work in excess of AG for the reaction may be used to supply process heat, or excess chemical reducing agent burned to supply process heat. Besides the thermodynamic and economic drawback, this inefficiency results in excess C02 emissions derived from the combustion of fossil fuels. With these practices, energy becomes an important cost element of the metal produced. Highly-concentrated solar energy has the demonstrated potential to separate these two forms of process energies, allowing the addition of only the thermodynamically required high-quality energy while high-temperature solar process heat is provided to the reactor. Examples of metal oxide reduction processes that have been studied experimentally in solar furnaces include the production of Fe, Al, AI/Si alloy, Mg, Zn, Tic, Sic, CaC2, TIN, Si3N4, and AIN by carbothermic reduction of their oxides, and the high-temperature solar- electrothermal reduction of ZnO.

Jan 1, 1999

By E. Ozberk

The copper and nickel smelting industries are important contributors to the technical and economic well-being of Canada while some of the smelters are among the largest sources of sulphur dioxide emissions in Canada. A review of the operations in six smelters - Falconbridge Limited, Falconbridge, Ontario; Hudson Bay Mining and Smelting Co. Limited, Flin Flon, Manitoba; Inco Limited, Copper Cliff, Ontario and Thompson, Manitoba; Noranda Mines Limited, Horne Division, Noranda, Quebec and Gaspe Mines Division, Murdochville, Quebec - have shown that about 80% of the total sulphur input to these smelters was emitted to the atmosphere in 1980. A simultaneous review of the existing and emerging technologies which can directly or indirectly reduce the sulphur dioxide emissions indicated that it is possible to reduce the emissions to below 20% of the sulphur input to these smelters. This can be achieved by varying degrees of modifications to the smelting operations and installing sulphur fixation facilities at significant costs which may increase the metal production costs. This would consequently make the competitiveness of the Canadian copper and nickel producers more difficult in the already tough world metals market.

Jan 1, 1983

By E. V. Verhoef

The proposed EU directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment promotes the substitution of lead in consumer electronics to reduce emissions from lead in the end of life phase. In this paper, the consequences of substituting lead in solders is assessed using the Eco-lndicator-99 method for the examples. The base metal production system is considered as an interconnected network modeled dynamically in Simulink 4 and Matlab 6 (Mathworks Inc 2000), where the recovery and production of metal components of the assessed product partially overlap. This approach requires global modeling of metal production processes and mass balances and resulting allocation choices. It also reveals the susceptibility of LeA scores to different choices in the modeling and data availability and uncertainty. Besides the comparison between lead-free and lead-containing solders, other side effects are revealed. Lead is carrier material for the recycling and production of many co-elements in the interconnected production and recovery system. Substitution may have adverse effects such as temporary shortages of other connected metals that are often not considered in normal LeA assessments, thus leading to erroneous results. The suggested approach provides directions for including these external effects and for further assessment of the environmental effects of substituting lead. This paper shows that in order to assess the environmental aspects of metallurgy, dynamic modeling of the total system is required based on the fundamental thermodynamics in each metallurgical reactor, the basis of this dynamic model. With this the true environmental impact of metallurgy can be explained. In the case of lead free solder, it is shown that the mining of substitutes has a very much larger impact.

Jan 1, 2003

By Pesic. Batric

A novel chitosan-pyridoxal-epichlorohydrin was synthesized and evaluated in our laboratories. The evaluation was achieved by performing kinetic and equilibrium studies of copper sorption. The parameters examined were pH, temperature, concentration of copper, particle size and selectivity of copper sorption against iron, zinc, cadmium and cobalt. It was found that pH was the most important parameter, and sorption of copper increased with pH increase in the range pH 2.5-6.0. The low activation energy of the sorption reaction, 1 1.13 kJ/mole (2.66 Kcal/mole), showed that temperature was not an important parameter. The synthesized chitosan was selective against iron, zinc, cadmium and cobalt. The selectivity with respect to last three metals was achieved by the kinetic difference of sorption, as sorption of copper was much faster than for other metals. Iron (Fe2+) does not adsorb on chitosan. The mechanism governing the sorption of copper is intraparticle diffusion. This finding was supported by the dependance of copper sorption on the square root of time, the low activation energy, and the fit of experimental data in the diffusion through the product layer equation.

Jan 1, 1994

By Guo Chen, Jin Chen, Jinhui Peng

"In this paper, the methods of life cycle assessment for microwave hot air systems, and the concept of green degree were proposed. Greenness evaluation index, evaluation system and evaluation model of microwave hot air systems were established. Also, life cycle assessment processing based on these ideas was introduced. Analytic hierarchy process and fuzzy decision- making method were utilized to establish and solve the greenness evaluation of assessment model, while the scores of green degree in microwave hot air systems were obtained. The results show that Life cycle assessment can be applied effectively and efficiently to the microwave hot air systems.IntroductionHot air systems are an important industrial operation condition, which is used to provide high temperature air for materials processing. Nowadays, high temperature airs are manufactured by the conventional heating processes, in which some ceramic materials are used as heating materials. However, these processes pollute the environment. Therefore, to explore new method to produce high temperature air with low energy consumption and less environment pollution are necessary.Microwaves are now being used in various technological and scientific fields in order to heat dielectric materials [1]. Microwaves irradiation has been explored in materials processing in recent years [2-3]. The main advantage of using microwave heating is that the treatment time can be considerably reduced, which in many cases represents a reduction in the energy consumption as well. Since there is energy absorption but no heat conduction, the heating is very rapid and highly efficient, resulting in energy savings and the shortened processing time [2, 4]. Compared with conventional heating techniques, the additional advantage of using microwave irradiation is that microwave irradiation achieves both internal and uniform heating [5-7]. In addition, it is more convenient to control the microwave irradiation processing, because of no direct contact between the heating source and heated materials with less equipment size and waste [2, 8-9]. Life cycle assessment is used and accepted methods for the evaluation of the environmental impacts of products or systems [10]. Recently, many appropriate evaluation methods have been developed for life cycle assessment [11-12]. These proposed methods usually are employed for the evaluating product and analyzing results [13]. Among them, the analytic hierarchy process and the fuzzy comprehensive evaluation stand out as a popular method utilized in many fields [14-16]. Analytic hierarchy process and fuzzy comprehensive evaluation are a combination of mathematical and statistical technique that is useful for analyzing the effects of several independent assessment aspects on the system goal without the need of the predetermined relationship between the objective function and the assessment aspects [17-19]."

Jan 1, 2013

By L. Xia

Sodium silicate(s), also known as “water glass”, are one of the oldest and most widely used industrial chemicals. Its first use in Canadian operations can be traced back to around 1925, which coincided with early use of xanthates in mineral flotation. Silicate functions as a sulphide and non-sulphide gangue mineral dispersant, depressant and modifying reagent in grinding and flotation operations. It is believed that soluble sodium silicate promotes selectivity of value added sulphides against gangue minerals, resulting in both grade and recovery improvement. This paper seeks to link improved grade/recovery to the interaction characteristics of minerals and the sodium silicate. A systematic study was performed with individual mineral species, an artificially designed model ore and the feed ore from a copper flotation operation. The function of sodium silicate was evaluated in the context of colloidal chemistry and linked to mineral surface chemistry. Measurement of pulp rheology and mineral zeta potential identified that sodium silicate works as a dispersant. The dispersion is accomplished by increasing a mineral’s net surface charge, resulting in a change in slurry viscosity. Bench scale laboratory flotation tests suggest that better dispersion leads to a diminished interaction of chalcopyrite with gangue. The improved Cu grade and recovery then are likely in response to an increased accessibility to collector along with a linked increase in particle bubble attachment resulting in better separation efficiency. ToF-SIMS surface chemical analysis of the flotation samples found a higher proportion of sodium silicate on minerals from the flotation tailings relative to the concentrates. Moreover, attachment of sodium silicate appears to be mineral specific; the data indicates that sodium silicate favours the surface of gangue phases over the value sulphides.

By Kymberley Worrell

The Cripple Creek and Victor Gold Mine was acquired by Newmont in August 2015. The high grade flotation mill project was commissioned in February 2014. The mill to date has been throughput limited due to mechanical and design issues. In order to create the most value from a throughput limited plant a campaign to provide timely ore characterization was undertaken. A diagnostic leach methodology was developed to determine gold associations by ore type. The resulting associations were then used to characterize feed blend; gold losses and optimize gold production. The diagnostic methodology is presented along with discussion on flotation implications.

By Alexey Lozhko

The technical-and-economic furnace exploitation indices are considerably influenced by the system of heat utilization. In the situation of total output decrease works are forced to exploit furnaces at the partial loading, sometimes even at the idle running for the sake of steam production. The furnace exploitation in this regeme is known to cause the increase of the heat portion, taken away together with waste flue gases. The losses can be partially compensated at the expense of heat exchange efficiency development in the recuperator or heat-exchanger. One of the well-known methods, characterised by high efficiency and low expenditures is the intencification of the heat exchange process by the means of pulsation method.

Jan 1, 2006

By Santo Ranieri

We will briefly review the nickel market in 2003 and look forward to the supply demand balance for the next few years focusing in on the key factors influencing future price dynamics. On the supply side we will examine slated brownfield and greenfield expansions including the Norilsk factor and the small to mid-range 'supply creep'. We will also review the cost side of the industry and what to expect going forward. On the demand side, we will discuss the stainless steel and non-stainless demand, the China factor and the stainless steel scrap supply cycle. We will conclude by pinpinting where the market is on the current price cycle, and where we believe the mid-term direction is headed.

Jan 1, 2004

By Tor Lindstad

Specific C02-emissions are given for the production of silicon-metal, ferrosilicon, ferromanganese and silicomanganese. Emissions taken into account come from reduction materials, from coke production and generation of electric energy. C02-emissions can be abated by direct and by indirect methods. A direct method is to replace fossil carbon as reduction material wholly or partially by endogenous carbon (biocarbon, charcoal). Another possibility is to produce metals by electrolysis instead of the present electric smelting furnace. Indirectly CO2-emissions can be reduced by energy recovery, thus saving coal, oil or natural gas for heat generation. Some reduction in global C02-emissions can be obtained by giving credit for the use of silica dust partially replacing cement in concrete. In addition to give an overview of possible methods, costs will be discussed.

Jan 1, 1999

By Husamuddin Ahmadzai

A survey of regulations and state of the art control technologies is presented relating to the smelting of primary aluminium, copper and recycling of residues. Some costs associated with the alternatives and trends for the coming decade in this. sector are identified.

Jan 1, 1992

By J. M. Skeaff

As much as 100% of the gold and 67% of the silver in a sulphur-bearing hydrometallurgical leach residue have been transferred to copper metal at copper smelting temperatures by dissolving the partially calcined residue in an iron-bearing slag maintained in equilibrium with the liquid copper metal and matte phases. The precious metals can then be recovered by conventional refining techniques. Copper can be recycled at least four times without any detrimental effects on gold and silver transfers and recoveries. Apparent copper recovery in the .process can be over 100% because of the copper content of the residue. Based on slag analys.es, the overal1 recovery of gold in the copper metal and matte phases varies from 94% to 100% under all conditions investigated. On the? same basis, silver recovery varies .from 9S% ?to 99% under optimum conditions, but is only 4S% to 73% under other, less attractive conditions. Unaccounted for silver losses of' about 30% make it difficult to determine the major factors affecting ?silver transfer and recovery. A method for implementing the technology on a commercial scale at a Canadian copper/zinc smelter has been proposed. A preliminary economic assessment and comparison of the proposed pyrometallurgical process with conventional cyanidation indicates that either process is economically attractive for recovering gold and silver from leach residues. Although the capital costs are higher, the pyrometallurgical process is simpler, has higher recoveries, lower operating costs and no .potential environmental problems related to cyanide disposal.

Jan 1, 1989

By H. Y. Sohn

The considerable progress made in the sulfide smelting technology since the first International Sulfide Symposium of 1983 is discussed. The new developments and innovations have largely been driven by the recognition of environmental concern as well as the need for increased productivity. The smelting technologies for various nonferrous metals are reviewed, with an emphasis on the industry trend towards larger plants and continuous processes. The tremendous advances made in process modeling and computer simulation to describe the complex smelting processes are also reviewed. The goal of these mathematical models is the quantitative description of the processes and the reactors that will provide a means for the control and optimization of smelting operations as well as the optimal design of the operating conditions and the reactors. Environmental issues remain a key consideration in the smelting industry. One of the most remarkable improvements made in the last fifteen years since the 1983 Sulfide Smelting Symposium is the rapid increase in the sulfur capture by nonferrous smelters. This and other related issues are briefly discussed. Finally, the challenges that the smelting industry faces as the new millenium approaches are discussed. The industry continues to face technical challenges to improve productivity and efficiency, while being responsive to ever-increasing public pressure for environmental protection. It also faces external challenges from factors that may cause the reduction of metal uses as a result of substitutions by other materials. Another serious challenge and dire consequence that the primary metals industry is expected to face is the serious diminution of university-educated manpower as well as basic-research output. To remain competitive and healthy, the industry should take up the void left by the complete disappearance, at least in the U.S., and the reduction in other nations, of the governmental support of higher education and basic research in the field of primary metals production.

Jan 1, 1998

By H. Deveci

Bioleaching/biooxidation is essentially a dissolution process with the involvement of acidophilic bacteria acting as the "catalyst" to accelerate the dissolution of metals from sulfide minerals. The contribution of bacteria to the metal dissolution is closely controlled by the growth of bacteria, which is itself affected by the physico-chemical conditions within the bioleaching environment. There are a number of operating parameters controlling bioleaching processes, which are required to be maintained within a certain range in the leaching environment whereby the activity of bacteria with the resultant oxidation of sulfide minerals can be optimized. In this regard temperature, acidity, oxidizing conditions, availability of nutrients, oxygen and carbon dioxide, surface area and presence of toxic ions are of prime importance for control and optimization of bioleaching of sulfide ores/concentrates. Bioleaching processes are temperature and pH dependent with optimum metal dissolution occurring in a particular range where the bacterial strain is most active e.g. mesophiles at 35-40°C and pH 1.6-2.0. Provision of nutrient salts is required to maintain the optimnm growth and hence metal dissolution with the quantity of nutrients apparently being dependent on the availability of substrate i.e. head grade/pulp density of an ore/concentrate. Oxygen transfer is one of the most critical factors since the oxygen levels below 1-2 mgll may adversely affect the oxidizing activity of bacteria. Bioleaching rate tends to improve with increasing the surface area at low pulp densities but, in practice. the pulp density is limited to -20010 w/v. Increasing concentrations of ions such as cr may also adversely affect the oxidative activity of bacteria. Keywords: Bioleaching, Biooxidation, Acidophilic bacteria

Jan 1, 2003

By Hideki Minoura

"Two novel electrochemical techniques for the preparation of highly crystallized CdS film have been presented. One is cathodization of a conductive substrate in an acidic chemical bath containing cadmium salt and thioacetamide, where electroreduction of proton at small current densities induces a growth of highly crystallized CdS thin films, whose growth is not disturbed by the reactions in the solution phase. The other technique is electoreduction of aqueous Cd2+— SCN complex. An advantage of this technique lies in no formation of solid particles in the bulk, of the bath.IntroductionIn recent years much attention has been paid to materials preparation by solution processing because of its advantages in lowering the cost as well as the stress to the environment, as compared to the conventional gas phase techniques which unavoidably require high temperature and/or vacuum. We have been trying to explore novel techniques for preparing functionalized compound semiconductors by aqueous solution process. Semiconductors which we have been mainly focusing on are CdS and ZnO, which are important semiconductors finding applications in various devices. In the present paper, some of the techniques that we have recently established for the preparation of highly crystallized CdS will be presented.Methods of the CdS film processing in solution phase (wet process), which have been reported so far can be divided into two major groups; one is chemical bath deposition (CBD) in alkaline solution containing Cd2+ and thiourea 1)4) and the other is electrodeposition (ED) in acidic solution containing Cd2+ and thiosulfate ions - 5)-8) or organic solutions containing dissolved sulfur 9)-11)."

Jan 1, 2000

By J. H. Corrigan

A series of six papers describing the Falconbridge Dominicana Ferronickel project were presented at the International Laterite Symposium held as a joint project of TMS-AIME in February 1979 at New Orleans. A review of the ore mineralogy, as well as. the processing and environmental practices as they exist today at Falcondo with emphasis on modifications put into practice since 1979 are presented in two papers: Part I.- Mineralogy and Ore Dressing E.W. Lithgow - General Superintendent ? Mines Falconbridge Dominicana, C. por A. Bonao, Dominican Republic Commercial volumes of nickeliferous laterite ores overlie part of a 90 km long belt of peridotites in central Dominican Republic. Protores are serpentinized harzburgites and dunites, with lesser serpentinite. The ore mineralogy consists mostly of goethite, serpentine-group minerals, quartz and poorly crystallized, X- ray amorphous materials. Minor constituents are hematite, gibsite, olivine and enstatite. In the Ore Dressing plant, the mine feed is subjected initially to proper sizing and blending to produce a homogenized mix. Subsequent drying and upgrading, by selective crushing and screening of rock kagments through a Barmac circuit, complete preparation of the ore for pyrometallurgical processing. Part II.- Pyrometallurgy, Fuel and Power Generation J.H. Comgan - Manager ? Production Falconbridge Dominicana, C. por A. Bonao, Dominican Republic Falcondo's energy requirements are based on oil which is refined on site to provide distillate to carry out drying and selective reduction of the nickeliferous ore in the shaft furnaces, plus bunker oil to produce electrical power for process melting, refining and ancillary use. The dryer product at 1.68% Ni is briquetted and passed counter current to hot reducing gas in 12 vertical shaft furnaces. The hot calcine discharge is melted in two high power electric furnaces at very high secondary voltage. The crude ferronickel is ladle refined and cast as 15 kg ingots or 125 gm ferrocones.

Jan 1, 1993

By Thomas F. Nederpel

The production of zinc and zinc-aluminum coated strip can be reasonably accomplished on a single operating unit. However, if the hot dip coating line is equip d with only one mo 7 ten metal holding furnace, it is necessary to transfer liquid metal of different chemistries and reintroduce virgin material to obtain the 18" necessary balance of elements in the bath. Dofasco produces Galvanize and Galvalume on a coating line with a sin le liquid metal furnace and has developed not only an efficient liquid metal trans& system but also an effective means of reutilizing the zinc-aluminum mixtures without detrimental quality affects.

Jan 1, 1992

By H. Soto, J. Jara, F. Nava

A method has been developed to recover cyanide and copper from solutions containing copper complexes and thiocyanate. Copper is precipitated as copper thiocyanate or as copper cyanide depending on pH and the concentrations of thiocyanate and cyanide in the effluent. The copper precipitate assays over 50% copper and presents good dewatering characteristics. After settling it can be separated from the effluent by filtration. The solution containing the bulk of the cyanide is then oxidized with ozone to transform the remaining thiocyanate into cyanide. This results in a regenerated solution rich in free cyanide that can be recycled to the cyanidation process. Careful control of the pH of the solution is required. First, pH of the effluent is lowered to optimize the precipitation and oxidation stages, then the pH is restored to an alkaline value to regenerate the cyanide solution. Recoveries of over 96% copper and cyanide were obtained in laboratory tests using industrial solutions. With this procedure, cyanocidic gold/copper ores could be treated economically by heap leaching, since the cyanide consumed by the copper impurities could be regenerated at very low cost (most of the cost of cyanide regeneration would be compensated by the copper credits). In order to achieve this, a bleed of the barren solution could be treated by the proposed method, and then recycled to the leaching step. The volume of solution to be treated should be large enough to keep a cyanide/copper molar ratio higher than 3:1. This would assure that copper does not cause undue interferences in the leaching or the carbon adsorption stages. If the thiocyanate content is low, the oxidation stage can be avoided, and the solution can be recycled to the leaching stage directly after the solid-liquid separation stage.

Jan 1, 1997

By Adam Powell

A Cahn-Hilliard phase field model is formulated to describe transport-limited electrochemical reactions coupled with fluid flow in a metal reduction cell. When the reaction is limited by mass transfer of metal ions from the electrolyte to the cathode, the metal-electrolyte interface at the cathode exhibits a Mullins-Sekerka instability, leading to the growth of dendrite-like "streamers" of liquid metal into the electrolyte, which in turn significantly enhance the apparent mass transfer coefficient there. Model results for iron reduction from ferrous oxide in slag show formation of these streamers. Although the double-layer is not included in this model, the related phenomenon of electrocapillarity can be represented by a gradient penalty term which includes the electric potential gradient, such that interfacial energy is a function of the electric field normal to the interface.

Jan 1, 2003