Search Documents

By V. Jiricny

There is a growing need to process galvanized steel scrap from automobiles, etc., in order to remove the zinc coating that otherwise causes problems in remelting of the scrap in electric arc furnaces. One approach that has moved to the pilot plant stage is that of Metal Recovery Technologies, Inc., of East Chicago (MRI). That company leaches the zinc fiom the scrap with a sodium hydroxide solution. The leached and washed scrap can then be returned to the steel industry. What is left is a sodium hydroxidelzincate solution which must be processed to recover the zinc and the NaOH. Presently, this is done by MRI using electrodeposition on planar electrodes at moderate current density and the resulting zinc is in the form of fine powder which is hard to process into, say, zinc for galvanizing. MRI has supported an investigation of a novel electrode, the spouted bed electrode (SBE), for zinc electrodeposition. In laboratory cells, zinc particles with low porosity have been grown up to 3mm in size. Microanalysis of the deposited zinc showed low level of impurities. DC energy consumption values were usually in the range of 2-2.5 kWg which is well below the energy consumption of the existing cells (and of present-day cells for electrowinning from acid sulfate electrolytes). These results were achieved at current densities (few thousand A/m2) that are much higher than possible with conventional electrodes. Discussion is provided of the scale-up of the cell to a commercial scale.

Jan 1, 1998

By Derek J. Fray

"In order to extend the application of fused salts in\the electrowinning and electrorefining of metals, it is necessary to maximise the current density, minimise the voltage drop and greatly increase the area of electrode surface so as to compete with the space-time yield of pyrometallurgical reactions. The various designs of electrowinning cell are reviewed and it is shown that by the application of a modest centrifugal field it is possible to reduce the anode to cathode interelectrode spacing to 4 mm whilst still maintaining a current efficiency of 85-90%.The thermodynamic potential for electrorefining is far less than for electrowinning yet fused salt electrorefining is only applied in limited cases. The reasons for this are discussed and the important design parameters evaluated. It is concluded that by using packed bed electrodes, separated by a diaphragm, the possibility of electrorefining with very low energy consumption can be achieved. Carbothermically-produced metals are always cheaper than those produced by electrolysis but suffer from the disadvantage of low purity. It is proposed that fused salt electrorefining may offer an energy efficient way of upgrading the metal. IntroductionThe majority of metals can be deposited from fused salts (1,2) but as commercial production is restricted to the more reactive elements, it is worthwhile considering the advantages and disadvantages of fused salt electrolysis as' compared to smelting and aqueous electrolysis. The advantages over aqueous extraction are as follows:1) the much higher conductivities and diffusivities result in much lower IR losses and higher current densities can be achieved at modest voltages;2) the elevated temperatures of operation result in larger exchange currents which give rapid kinetics and lower activation polarisation for the electrode reactions;3) the absence of water as a solvent means that it is not necessary to consider the evolution of hydrogen as a competing cathodic reaction. Furthermore, alkali halide salts, often used as solvents in fused salt electrolytes, have high deposition potentials;4) molten salts generally are mutually soluble and, therefore, concentration polarisation effects are minimised."

Jan 1, 1988

By N. L. Piret

In copper smelting minimization of solid waste generation is receiving increased attention with more stringent environmental legislation and lower disposal space availability. Copper smelting slags generally being valorizable, solid waste generation is attributed to the presence in the feed of unvalorizable impurities which do not report to the slag and to the unavoidable formation of contaminated dilute acid solutions which need neutralization. As to unvalorizable impurities, solid waste minimization is achieved by rejecting them in the highest possible concentration. Dilute acid is mainly due to the formation of SO3 in the smelter gases and to the discard of decopperized bleed-off electrolyte. Its generation is substantially lowered by preventing SO3 formation, by converting the dilute acid to a valorizable product, e.g., by thermal decomposition for H2S04 recovery or by precipitation as chemical gypsum, and by suitable treatment of the bleed-off electrolyte for impurity removal. Industrial processes are evaluated and alternatives are discussed.

Jan 1, 1994

By Sharif Jahanshahi

Calcium ferrite slags are often associated with Professor Yazawa due to his pioneering work on the thermodynamics of this type of melts. Over the past years CSIRO has invested some effort in studying physico-chemical properties of such melts to fill in some gaps in our knowledge and explore opportunities for application of the understanding developed. These investigations cover thermodynamics, transport properties of calcium ferrite based slags, as well as the kinetics of reactions of such slags with refractories. The present paper provides an overview of some of these studies and highlights some of the interesting behavior of such melts. The oxidation state of copper and arsenic in calcium ferrite based slags are predominantly Cu+ and As3+, respectively, at oxygen potentials below 10.1 atm. The concentration ofCu2+ in such slags becomes significant at oxygen potentials of greater than 10'1 atm at 1300 ?C. The activities of CuOo.s and AsOl.S in calcium ferrite slags show strong deviations from the Raoultian Law, while that of CoO is very close to ideal behaviour with respect to pure solid CoO. Addition of Si02 to calcium ferrite slags can have significant effects on the activities of FeO and Fe2O3 and hence the stability of magnetite phase. Transfer of oxygen in calcium ferrite slags is fast with diffusivity of 2xlO?3 cm2/s at 1350 °C and activation energy of 16 kcal/mol Presence of solid phases, such as magnetite, has pronounced effect on the viscosity of calcium ferrite slags. The observed dependence on solid loading and shear rate indicates deviation from Newtonian behaviour. The interfacial tension between copper mattes and calcium ferrite slags is strongly dependent on the matte grade, with the determined values being much lower than the corresponding ones for interfacial tension between similar mattes and iron silicate slags. MgO, Cr2O3 and MgCr2O4 have low solubility in calcium ferrite slags and their solubility increases with increasing copper oxide content of the slag at 1300 °c. The oxidation state of the slag has strong effects on phase transformation, dissolution rate and disintegration of refractories in calcium ferrite slags. Other key factors with major impact on slag-refractory interactions include viscosity and surface tension of slags as well as the contact angle between slag and refractory material.

Jan 1, 2003

By Jun Iwai, Osamu Takai, Yasushi Inoue, Hiroyuki Sugimura

"Infrared reflection absorption measurement was performed during plasma-enhanced chemical vapor deposition of silicon dioxide films at room temperature. Hydrocarbon contaminants adsorbed onto growing film surface are oxidized by oxygen radicals in plasma resulting functional groups which include C=O and C-O bondings. These groups exist only near the surface and are hydrolyzed rapidly after exposure to air.IntroductionRecently low-temperature silicon dioxide (SiO2) deposition has been in a growing industrial demand in pa1ticular, polymelic substrates such as polycarbonate and polyethylene telephthalate, which have poor heat resistance, need low process temperature (near room temperature) in coating of SiO2 which is a suitable material to improve optical and mechanical properties of polymenc products. Plasma enhanced chemical vapor deposition (PECVD) using organosilicon reactants is one of the most promising technique for lowering process temperature, so that it has been extensively studied1-12. In the present; however, hydrocarbon contaminants and a plenty of Si-OH termination in Si-O-Si networks tend to exist in the films, which degrade mechanical, optical and electrical properties of the films. It is necessary to understand the deposition mechanism at, low temperature in order to solve the problems. We have studied the low-temperature PECVD of Si02 by spectroscopic diagnosing techniques such as optical emission and mass analysis6-7, 11- 12Infrared reflection absorption spectroscopy (IR-RAS) has been a well-established technique for characterization of thin films on metals as· well as on semiconductors and insulators13-17. In this paper, we report on' the surface reaction of room-temperature PECVD of Si02by using in situ IR-RAS."

Jan 1, 2000

By Boyd Davis, Vladimiros Papangelakis, Joshua LaMarre, Jan de Bakker

"HCl leaching using molten salt hydrates has the potential to improve the extraction of nickel from laterite ores. However, as in other HCl leaching applications, recovery of HCl is key to process economics. Spray pyrohydrolysis, which is used in current chloride-based flowsheets, is associated with a high energy cost. The authors have developed a proposed laterite leach circuit using an alternative HCl recovery route. The leach circuit envisions a leach by concentrated (33%) HCl in an MgCl2 molten salt hydrate (MSH) or brine medium, followed by Ni/Co recovery and iron precipitation. Magnesium and chloride are precipitated from solution as magnesium hydroxychloride; this hydroxychloride is thermally decomposed to produce HCl gas. The proposed flowsheet employs a chloride leach circuit with simpler equipment and lower energy cost than in the conventional practice of pyrohydrolysis. Laboratory work investigated key aspects of the flowsheet, including precipitation of magnesium hydroxychlorides and their composition; magnesium hydroxychloride thermal decomposition; and iron control.Introduction As sulphide nickel ores become harder to mine and more complex to process, laterite ores will increase in importance. Laterite ore deposits can be divided into two main mineralogies. Limonite ores consist mostly of hydrated iron oxide, FeOOH, with 1-3% nickel substituting for the iron. Saprolite ores consist of iron-magnesium silicates, (Fe, Mg)2Si04, again with some nickel substituting for the metal ions. Limonite ores can be treated using the HP AL (High Pressure Acid Leach) process, in which the ore is reacted with sulphuric acid at high temperature in an autoclave. HP AL, however, cannot in general be used to treat saprolite ores because the magnesium enters solution and consumes sulphuric acid, which results in excessive spending on lixiviant. It is therefore desirable to find a hydrometallurgical process specifically for saprolite ores that can provide better results than the treatment options currently available."

Jan 1, 2011

The Port Kembla Copper (PKC) copper smelting facilities were commissioned during 2000. Numerous difficulties were encountered during the commissioning such as multiple reactor tuyere line failures, absorbing acid tower refractory collapse, and Noranda Reactor and Mitsubishi Converter process control problems. These problems are described along with the actions taken to overcome them. Process development is described particularly for the Mitsubishi Converter and Acid Plant.

Jan 1, 2002

By Jianhua Xin, Min Chen, Cuihuan Huang, Shan Yu, Xiaoao Li, Nan Wang, Guanghao Chen

Copper enrichment behavior in continuously cast slab induced by scale formation after continuous cooling in H2O vapor atmosphere and consecutively in air has been experimentally investigated by combining with SEM-EDS analysis, for the purpose to examine the effects of initial slab surface temperature and contents of copper and nickel. For Slab 1 with copper content of 0.1 percent, no visible copper enrichment is found at scale-substrate interface irrespective of the various scale microstructures formed at different initial slab surface temperatures. For Slab 2 with higher contents of copper and nickel, copper-rich phase accumulates and stays at scalesubstrate interface under the condition of lower initial slab surface temperature; while Cu-rich phase in the porous scale formed at higher initial slab surface temperature is noted with simultaneous Ni-enrichment appearing in front of the steel-scale interface. Both a porous scale and high nickel content work together to provide pores for copper-rich phase migration away from interface and occlude within the scale layer.

Jan 1, 2016

By William Petruk

The capabilities of SEM/image analyzers for determining quantitative mineral data which have a bearing on extractive metallurgy have given applied mineralogy a new dimension. The capabilities include automatic mineral identification, unattended operation, search for rare minerals, and measurements of (1) mineral quantities, (2) grain and particle size distributions, (3) liberation characteristics of minerals in ground ores, and (4) mineral associations. Data on mineral quantities define the distributions of elements among minerals, provide background information on characteristics of the samples, and provide a data base for a mineral-materials balance. Size analysis data of the minerals in unbroken ores are used to predict the grind required to liberate minerals. Data on liberation analysis can be used in many ways. One application is to process the image analysis data for feed, concentrate and tails by a materials balancing technique to calculate the recovery of liberated and unliberated grains at each point in a circuit. The calculated recovery data define the behaviour of an ore in a concentrator, pilot plant or bench test, and indicate whether recovery improvements are possible and/or feasible for a particular ore.

Jan 1, 1991

By Muhlis Nezihi Saridede, Burak Birol

"Plastic wastes become a huge problem day after day due to the growth of plastic industry. Hence, plastic wastes are used as a raw material for other industries to eliminate this problem. Polyethylene Terephthalate (PET), which is a commonly used for plastic bottles, may be used as a reductant for iron production because of its C and H content. In this study, composite pellets containing iron ore concentrate, flux and reductant were prepared. Crystallized PET bottles and coke were used as reductant after ground. The prepared pellets were reduced at 1400°C for 30 min. and iron nuggets were produced successfully. Usage of waste PET purely as reductant in composite pellets gives a higher metallization degree and proper carbon content than coke or PET and coke mixture.IntroductionPlastics can be seen everywhere, especially at packaging industry in our common life. The increase of plastic usage ends up with an important problem, the increase of plastic wastes. Many studies have been carried out about usage of plastics as reductant in blast furnace such as Ogaki et al.[1], Heo and Baek [2], Saridede [3], Minoru et al.[4], etc. Besides, Kato et al. [5], Nomura and Kato [ 6] and Rongfang et al. [7] have pointed out the use of plastics in coke ovens regarding to its calorific content. In EAF steelmaking, a mixture of coal/coke and plastics can be used as an energy resource instead of only coal or coke. [8] Also, the usage of PET and PC in self-reducing composite pellets increased the reduction rate. [12]PET (Polyethylene terephthalate ), which is commonly used for soft drink plastic bottles, is an important municipal waste due to its C and H content. Its molecular formula is (C10H8O 4)n. Demir and Dincer showed that PET can be crystallized at 250°C to have the ability to be ground to a size of -100 µm. [11]"

Jan 1, 2011

By E. A. Werner, A. Pichler, A. Spalek, G. Reisner, P. Stiaszny

"Interstitial free (IF) sheet steels are used for complex shaped parts because of their excellent formability. If a deep drawn part is subjected· to a impact deformation at low temperature brittle fracture of the part may occur. This phenomenon\ is called secondary work embrittlement (SWE). One possibility to characterize this material/structural behavior is the drop-weight test. The result of .this .test is a temperature at and below which a crack can initiated in a deep drawn part under the investigated set of parameters. This paper addresses the influence of the preforming process on the sus- . . ceptibili.ty of IF steels to SWE.IntroductionInterstiiial:free (IF-) steels are frequently used in the automotive industry for complex· shaped p·arts because of their excellent deep drawability. The microstructure of the steel consists of a highly ductile ferritic matrix with embedded precipitates of nitrides and/or carbides. Brittle fracture can occur in deep drawn parts, if they are subjected to a high speed deformation at lo""w temperature. This phenomenon is called ~econdary Work gmbrittlement (SWE) [1-11]. Up to now there are no standardized testing procedures available to quantify the sensibility of IF-sheet steel to SWE. Neveitheless, a reasonable testing procedure which allows to quantify the tendency of a predeformed part to SWE is necessary for further material development. A commonly used test method is the drop-weight test performed at low temperatures. In such ·tests a cone-like drop weight expands a deep drawn cylindrical cup [l-3, 6, 8, 9, 11]. From this expansion experiment the temperature is determined at and below which a brittle crack can be initiated in the deep drawn cup under the investigated impact test parameters. The highest measured temperature at which a deep drawn cup fails by brittle fracture is called frack appearances !emperature (CAPT). The lower the value of the CAPT the lower is the sensibility of a deep drawn part of IF-sheet steel to SWE. This paper aims to clarify the role of the preforming process on the impact behavior of an IF steel. For this purpose a numerical analysis of the deep drawing process and cup expansion tests are conducted."

Jan 1, 2000

By Zhou Jiemin

A mathematical model is developed to determine the economic thicknesses of refractories and insulations in rectangular furnaces, Both the heat loss cost and the lining investment are taken into account to achieve a minimum operation cost. For the sake of calculating the heat flux, the paper is particularly concerned with the simulation of the three-dimensional transient heat conduction processes in the lining and a Douglas-Rachford method is used to solve the finite difference equations, The model has been used to design an industrial electric resistance furnace operated periodically. the values of temperatures and power consumption measured from the furnace correspond with the model results.

Jan 1, 1991

By Katragadda Sarveswara Rao

"In view of the increasing importance of processing lean ores as potential future resources, efforts are being made worldwide to develop suitable technologies for the recovery of both nonferrous, base and precious metals. There are various types of low grade ores present in many countries. Gradually, the mineral reserves for production of metals have undergone complex changes with regards to their grades and particularly the physical and chemical properties of the minerals to be separated from each other. So, there is a need for new processing routes or the upgrading of existing technologies to recover metal values that are otherwise unutilized. Accordingly, an overview of the different types of mineral resources and economical processes, based on ore horizons, consumption of energy and reagents and environmental concerns, is made in this paper. In addition, the paper provides a summary of metallurgical and engineering challenges to be overcome when implementing new technologies and concepts with regard to base metal extraction and sulphur removal efficiency.IntroductionLow grade multimetal complex sulfide ores are likely to become an importance source for nonferrous as well as precious metals in the near future. The principle metallic minerals are chalcopyrite, sphalerite, galena, pyrite, pyrrhotite, arsenopyrite, tetrahedrite, boulangerite and cassiterite. Such ores are located throughout the world as multi-pocketed reserves which have present complex challenges with regard to their grades and particularly the physical and chemical properties of the minerals to be separated from each other. Their compositions can vary widely from one deposit to another and even from one location to another in the same deposit, and this poses a problem for the recovering metals present therein. Successful aqueous processing of complex sulphide ores depends on the composition and mineralogy of the raw materials and on their leaching behaviour."

Jan 1, 2012

By A. Robles

The main goal of the present work is to propose a viable alternative for selective arsenic elimination from copper smelter flue dust without the need of a global leaching scheme for all the individual components of the flue dust. Using this alternative, the inherent copper recovery problems are avoided. Arsenic precipitation is also considered for regenerating the solution and completing the process cycle. The experimental results for arsenic extraction and precipitation are satisfactory. Concentration of NaOH used was relatively low. The main reason for succeeding in high arsenic extraction and low NaOH consumption is due to the previous water washing of the flue dust. Water washing dissolves much of the iron and copper that are present in certain percentage as sulphate.

Jan 1, 1999

By Takashi Ikeda, Masafumi Maeda

"Demand for solar cells is increasing linearly throughout the world. Last year production totaled 3000 tons worldwide. The market size of solar silicon is expected to increase further because of international ""political"" demand to reduce carbonaceous emission from energy consumed. Most elemental silicon is produced by the carbon reduction of Silica in an electric arc furnace. Purity of silicon at this stage is 90-99%. Major impurities are Fe, Ti, Ca· and Al, and minor ones are P, B and carbon. The oxidizing metallurgical process is no longer effective to remove transitfon metals because those are less noble to silicon. Nonmetallic impurities such as phosphorus and boron must be reduced to 0.001ppm for semiconductor use. The most common process for high purity silicon is the Siemens C process, which is basically distillation of hydro-chlorinated silicon followed by CVD of SiHCl3. The cost of such silicon is expensive to allow its popular use in solar cells. Currently scrap silicon -of semiconductors is used for this; however, the supply-of that scrap is limited to just a portion of semiconductor production.In this paper world demand for silicon will be reviewed and some of the processes proposed summarized.IntroductionSilicon is element 14 in atomic number and has an atomic weight of 28.0855. Little elemental silicon is found in the earth, and it is mostly found as oxides or silicate. The Clark number of silicon is very large and the second in its number. If we were discussing the volatility of silicon element on the globe, we would never worry about it. However, it is very difficult to obtain pure elemental silicon because a high purity silicon compound is very rare. In most cases these are silica (silicon oxide SiO2). As shown in Table 1, there are many grades of silica ore classified mainly by their content of iron and alumina."

Jan 1, 2000

By G. Laird, N. B. Gray, N. Lawson

"Photographic, video, laser, hot film and conductivity methods are used in the experimental study of gas-liquid flows. A discussion of their capabilities and limitations are given in this paper illustrating the wide range of phenomena that can be studied. Most of these methods are limited to physical models at room temperature with transparent fluids, although they can be extended for use with opaque and hot fluids. A number of these techniques have been used by the GKW CRC in studies on industrial plants and their usage is increasing although a number of technical difficulties still need to be overcome. An in-depth discussion of the laser doppler anemometry (LDA) and particle image velocimetry (PIV) methods is given with experimental results on the flow field of an air plume in water based on advanced development of the techniques and studies carried out at the GKW CRC. The LDA method provides high resolution data on the velocity profiles, while the PIV method provides an overall view of the complex flow structure occurring at the gas-liquid regions. These two methods complement each other in providing experimental data for validating numerical models and exploring the complexities of multi phase flows.IntroductionThe injection of gases into melts is an important operation in the metallurgical industry. It is used in converters, anode furnaces, blast furnaces, ladles, bath smelters, zinc fumers and many other smelting processes. In many of these processes, the gas is injected into a molten bath resulting in the formation of bubbles that promote reaction, mixing, alloying and heat transfer. The study of gas-liquid systems presents enormous challenges to the researcher due to the complexity of the mathematical and physical modelling which require innovative numerical and experimental skills."

Jan 1, 1996

By M. Zamalloa

Slag foaming is an important phenomenon in many metallurgical processes. It creates large surface areas for multi-phase reactions to take place. In other applications, it protects electrodes and improves the energy efficiency by reducing radiation from hot surfaces. However, it may also be a source of serious disturbances. To control and optimize the use of slag foams, an extensive knowledge of the factors controlling the foam formation and stability is required. Slag foaming experiments were carried out using synthetic FeO-CaO-Si02 slags at temperatures ranging from 1200 to 1350 "C. A data acquisition system was used to continuously measure the foam height, gas flow rate, bubble frequency and temperature. The experimental results show that the gas injection rate has a strong effect on the behaviour of slag foams. At high flow rates and rapid bubbling, unstable foams with short decay times were created. The addition of P20, favours the foam formation and stability by lowering the surface tension of the slag. The average foam life increases with decreasing basicity (CaO/Si02). It is proposed that this is attributed to the increase of the surface viscosity due to surface adsorption of a thin film of silica, retarding the drainage of the liquid films.

Jan 1, 1992

By Z. Sadowski

The influence of organic acids simple salts and A. niger saccharose and molasses worts on sodium oleate adsorption on the salt-type mineral surfaces has been studied. It was found that salts of organic acids had an effect on the sodium oleate adsorption on barite calcite and magnesite. The collector adsorption on the barite and calcite surfaces decreased under the influence of investigated worts. Experimental data suggest that the biomodification of salt-type mineral surfaces can be used for the selective separation of these minerals.

Jan 1, 1991

By Richard D. Hagni

Reflected light microscopic examination of particles from laboratory experimental copper flash furnaces operated under varied furnace conditions shows that the particles exhibit a wide range in mineral compositions and mineral abundances that correlate with partial pressure of oxygen and concentrate/oxygen ratio. Chalcopyrite, bornite, and digenite are more abundant under low oxygen conditions. With increasing oxygen, metallic copper, delafossite and cuprite become increasingly abundant. The extent of particle agglomeration during flight varies with the furnace. Those products from the larger furnaces exhibit the greater degree of agglomeration. Significant particle fragmentation also is evidenced by cracking and brecciation of some particles.

Jan 1, 1991

By Takuya Shinagawa

After vitrification of the residues from a municipal solid waste incinerator, the vitrified products can be used as a construction material, and the dust can be used as raw materials for the non- ferrous industry. The NKK electric-resistance furnace is operated under a reducing atmosphere, and heavy metals such as zinc and lead in the ash vaporize to form dust. Also, dust from the NKK electric-resistance ash melting furnace is composed of water insoluble zinc and lead components and water soluble NaCl and KCI. This is why, The concentration of zinc and lead in the dust after washing is sufficiently high for the dust to be used as a raw material for the zinc and lead industry. NKK developed a heavy metal recovery process in which zinc and lead in the dust are reclaimed as a raw material for smelting by making the best use of the characteristics of the dust.

Jan 1, 2002