Search Documents

By Andrew J. Hyett

The ISRM commission on testing methods has recently presented Suggested Methods for rock stress determination (Kim & Franklin, 1987). This proposes that even if the magnitude of in situ stress is not sufficient to cause significant ground problems, the optimum shape, orientation, and layout of underground structures can be significantly affected by it. In the design of underground excavations, the engineer often requires a knowledge of the average in situ stress tensor in the rock mass. However, attempts to measure a stress state applicable to design have proved frustrating, and a high degree of uncertainty is introduced by the variability in results. In the belief that deduced fluctuations are random in nature, many separate measurements are often made, so that a more reliable stress tensor average, and some indication of the associated variance (see Dyke et al., 1986) can be calculated. Unfortunately, this approach is limited by economic considerations and, as with any sampling procedure, it is imperative to understand the sources of measured variability, in order to design an optimum measurement programme. Cundall(1987) itemised the main causes of stress variability as a. Instrument and measurement errors, and b. Natural fluctuations of stress from point to point, induced by the action of a boundary stress on the internal rock structure. At least four categories exist: i. inhomogeneous rock, bedding, intrusions etc.; ii. differential contraction, creep, or changes in rock properties with time; iii. proximity to faults or discontinuities; iv. cycles of tectonic activity that cause movement on joints. The latter was successfully investigated using the distinct element programme UDEC. In this paper, the contribution of items (iii) and (iv) (i.e. the items related to discontinuities) to the total stress variability will be discussed, for the kind of rock mass shown in Figure 1. Although many authors have concluded that rock joints have an influence on the stress in their vicinity, a more analytical approach is required if the stress distribution associated with different jointed rock masses is to be (i) compared, and (ii) related to routinely measured joint parameters. If this can be achieved then, prior to any attempt to measure stress in a jointed rock mass, a consideration of joint geometry, joint deformability, and the geological kinematics of joints (e.g. the magnitude and direction of previous movements), can place valuable `common sense' constraints on the expected stress system for minimal extra cost.

Jan 1, 1989

By Christopher Mark

Preventing pillar line squeezes, massive pillar collapses, and coal pillar bumps is critical to the safe and efficient recovery of coal during retreat mining operations. To help prevent these problems, the U.S. Bureau of Mines has developed the Analysis of Retreat Mining Pillar Stability (ARMPS) computer program. ARMPS calculates stability factors (SF) based on estimates of the loads applied to, and the load-bearing capacities of, pillars during retreat mining operations. The program can accommodate various retreat mining scenarios including angled crosscuts, varied entry spacings, barrier pillars between the active section and old (side) gobs, and slab cuts in the barriers on retreat. It also features a pillar strength formula that considers the greater strength of rectangular pillars. The program may be used to evaluate bleeder entry designs as well as active workings. A data base of 130 pillar retreat case histories has been collected across the United States to verify the program. It was found that satisfactory conditions were very rare when the ARMPS SF was less than 0.75. Conversely, very few unsatisfactory designs were found where the ARMPS SF was greater than 1.5.

Jan 1, 1995

By Y. P. Chugh

About 60-70% of the underground mined coal in Illinois is extracted using a room-and-pillar mining method that permits extraction of about 50% of the coal. The remaining coal is left behind in the form of support pillars to control surface and subsurface movements. Illinois coal seams are typically associated with water sensitive weak floor strata whose thickness varies 0.31 - 1.3 m. The current mining geometry mostly uses pillars of constant size within a mining area. This traditional practice suffers from the disadvantage that pillars within the center region are subject to much higher loads than the pillars located on the outer edges of the panel. This results in a higher incidence of rib spalling, and roof falls, creating a potentially hazardous work environment. In addition, this concentration of loading at the center of the panel provides initiation points for floor failure to occur. The primary goal of this study was to reduce ground control problems and production costs in Illinois mines by considering alternate mining geometries. The development and subsequent field demonstration of an alternate geometry is presented in this paper.

Jan 1, 2004

By Axel Preusse

Stowing or waste fill is common in the German mining industry since the beginning of mining activities, With increasing mechanization, flat and gently inclined seams (0 -- 18) were mined. These mines were located within the densely populated areas close to important infrastructures such as industrial complexes, roads, highways, railroads, rivers and canals. These buildings and infra¬structures were rarely protected against subsidence influences and other ground movements and dump capacities close to the mines were exhausted. For subsidence reasons and because of the low dump capacities pneumatic stowing methods were continuously developed and used in German longwalls until 1997. Due to techni¬cal standards and because of some restrictions pneumatic stowing in Germany is only used at a minimum seam thickness of 2.00 m and average costs of this method are $20 - 30 per ton. A significant reduction of the disturbance potential and by that a decrease in expenses for subsidence regulations due to reduced subsidence and ground movements could not be achieved. In this paper the experiences with pneumatic stowing in the Ger¬man mining industry are described. Possible subsidence reduction and economic aspects of pneumatic stowing are taken into account.

Jan 1, 2002

By Y. P. Chugh

The use of wooden supports, supplementary to the primary method of roof control using roof bolts in mines, consumes over 3 million cubic meters of hardwood in the U.S. annually. These supports arc primarily used in the form of cribs and posts. Along with a rapid depletion of high quality timber resources, supplies fluctuate seasonally, costs are escalating rapidly, and product quality is highly variable. Environmental considerations of global climate change put additional pressure on deforestation for utilization of timber for artificial supports. On the other hand, management of coal combustion byproducts (GCBs) from power plants has become a major issue to maintaining a healthy coal industry. The USA currently produces over 100 million tons of CCBs annually and the average cost for their management in the US is about $20/ton. This cost is expected to escalate rapidly with tougher environmental regulations. The principal author has been directing research, development, and demonstration studies for CCBs-based artificial supports and lightweight structural materials in mines for the past seven years and has made significant progress toward commercially viable products. More specifically, first and second generation crib elements and post elements have been developed, characterized analytically, and demonstrated in the field. It is estimated that about 2.5 x 10" tons of fly ash could be utilized for artificial supports in U.S coal mines and this would double if these materials were utilized in non-coal mines as well. The author believes that CCBs-based artificial supports have the potential to replace wooden supports and blocks with better performance and cost competitiveness while managing CCBs in an environmentally sound manner. This paper focuses on the development and field demonstration of CCBs-based artificial supports for use in underground mines, and its pilot scale fabrication facility. Recent analysis results on engineering performance evaluation of the developed crib under various loading conditions using finite element method are presented. The following comments highlight the developments: I ). Engineered artificial supports, crib and post elements, using CCBs as a major constituent, have significant potential for application in mines because their structural performance is significantly better than wooden cribs counterparts. 21. Engineered crib elements provide about 50% larger area for air-flow than a conventional wooden crib. 3). Engineered crib elements are not flammable. 4). Each engineered crib element utilizes about 10 kg of fly ash, about 40 % of the weight of crib element- Therefore, a typical crib 2.0 m high utilizes about 200 kg of fly ash. 5). Each 16.5 cm diameter engineered post utilizes 50 kg of fly ash. 6). Assuming 3.0 million cu. meter of wood consumed for post and crib support systems, it is estimated that about 4 - 5 million tons of fly ash may be utilized for supports fabrication in the USA. 7). An engineered post has excellent post-failure characteristics similar to wood. In addition, the engineered post also has excellent loading and unloading characteristics close to the yield point of about 75% of the ultimate load carrying capacity.

Jan 1, 2004

By Reha Ozel

The stability in longwall faces depends on the interaction beman the roof strata, face supports and floor strata. The load distribution on the other hand, depends upon relative stiffness of the three supporting elements namely, the coal face, support and gob. Therefore, in defining support requirements, it is particularly important to analyze the strata loading, the face convergence and the controlling mechanism provided by supports. The controlling mechanism however, depends on the type and characteristics of supports used in long- wall faces. The design guidelines presented in this paper have bean developed based on a number of strata control oriented projects carried out in Turkey, load and convergence measurements carried out in 10 longwall faces, in Zonguldak Coal Region, and procedures given in literature. Evaluation of load and convergence measurements, and analyses of face supports were carried out by means of a computer program, called L0NGWAI.L-MEW, developed by the authors. The output of the design analyses include the following: (1) estimation of support capacity for roof supports namely; individual hydraulic props, chock-type power supports and various types of shield supports, and (2) analysis of loading conditions and response of shield support components in terms of stability and structural integrity.

Jan 1, 1990

By Rusty Mchenry, Craig Dickerson, Robin L. Oldham

"It has been proven that longwall faces can be moved safely and efficiently. However, abutment pressures and poor ground control conditions can halt operations and be hazardous to coal miners. Recently at a mine in Southwestern Pennsylvania, roof material collapsed above shields that created two large voids and caused major challenges for shield recovery. A unique, engineering solution was developed that utilized a modified concrete material to fill the voids, creating stability in the affected area. The many phases of this project included the construction phase, void pumping, cutting out, and bolting of the concrete material. This project eliminated the hazards associated with bolting the recovery face and removing shields in adverse conditions, making it possible for the mine operator to safely complete the longwall move.INTRODUCTIONFrequently in the mining process, especially during the recovery phase, voids above the longwall supports have occurred. These voids are simply roof cavities caused by falling rock strata above the longwall face. Most often, this condition slows down or halts mining operations and creates hazardous work conditions for coal miners. Numerous methods of supporting void areas on longwall faces have been attempted and utilized throughout the mining industry since the advent of the longwall mining system. These methods have utilized many different materials and processes and have included the installation of steel or wooden beams, crib blocks, and various types of roof bolts. However, these methods can be dangerous due to exposure of personnel to the mine voids, falling roof material, and the necessity to handle large amounts of heavy support materials.This paper describes a unique case study in Southwestern Pennsylvania where longwall recovery methods, through two void fills, were successfully completed, eliminating exposure of coal miners to the rock voids above. At the start of this endeavor, normal recovery operations were halted, and hazardous conditions became a concern when the voids were encountered. However, in the interest of safety, the decision was made to try a unique method to completely fill the void from the bottom of the coal seam to the top of the void with a cementitious material and then mine through it. This is in contrast to traditional methods where beams and support materials are used to stabilize the area above and in front of the mine shields, which can expose miners to the void above."

Jan 1, 2015

By William Kendall

"A tremendous amount of research, analysis, and engineering time is used to design a proper roof support system including the type, length, and location of the roof bolts. Unfortunately, since the roof bolts are being installed under unsupported roof, the exact location for the bolt holes cannot easily be determined and then marked onto the roof. The actual location where the roof bolts are installed is typically left to visual estimates by the operator. This frequently results in either (1) the operator overestimating the space between roof bolts and installing more bolts than required, thereby increasing cost and reducing efficiency; or (2) the operator underestimating the space between roof bolts and installing fewer bolts than required, thereby reducing safety, leading to potential roof failure or possible violations.A patented laser light grid system has been developed by J .H. Fletcher and Monitech, a South African Company, to aid in proper machine positioning in the heading and proper bolt spacing. The system can also show when an entry is over width, requiring additional roof support. The system is relatively simple and inexpensive. The concept is applicable across the full range of roof bolters from low to high seams and from single boom to multiple boom bolters. The system can be configured to meet most bolting patterns.The system consists of several very small 1 milliwatt, class 2, line type lasers that project a line onto the roof. The actual laser is 27mm in diameter x 47mm long (1"" x 1.8""). In South Africa it is approved as intrinsically safe and is mounted inside a 50mm diameter x 64mm long (2""x 2.5"") protective housing. In the USA, we are seeking an X/P approval and the laser will be mounted in a headlight enclosure 110mm diameter x 125mm long (4.3"" x 5""). Fifteen of the systems have been installed in South African coal mines with good results.The system has aided the mines in meeting the bolt spacing tolerance used in the Republic of South Africa, which is typically 15% of the nominal bolt spacing or 7 in for 4-ft bolt spacing. Fletcher has submitted the system to MSHA for approval in the US."

Jan 1, 2016

By Thomas M. Barczak

The initial Support Technology Optimization Program (STOP), Version 1.0, was released at the 19th Gmund Control Conference. This original program has since been updated to Version 2.3 which was released in May, 2001. This paper describes the additional features of Version 2.3, focusing primarily on the following three aspects: (I) including uncontrolled convergence into the design requirements for standing roof supports, (21 the addition of design procedures for cable bolts as an alternative secondary roof support, and (3) the addition of new standing roof support technologies. Another new feature which should facilitate the development of design criteria for standing roof support is the capabilily to define ground reaction curves through convergence measurements alone wthout having to make support loading measurements. There are several other new features provided in Version 2.3 which are only briefly addressed in the paper. These include: (I) additional graphics capabilities to facilitate rapid assessment of support comparisons. (2) an East-West designation for support selection to more accurately provide cost and support availability data, (3) additional safety measures including a safety factor to identify support design near the peak support capacity, checks to see if the support dimensions comply with aspect ratio requirements, and measure of roof coverage for the design layout of the support system These new features of STOP provide more capabilities to design and analyze secondary roof support systems for conditions whlch could not be fully analyzed in the original version of the program.

Jan 1, 2001

By Murali Gadde

U.S. coal mines? primary roof supports typically consist of passive resin bolts; however, the use of active bolt systems is increasing. Despite this widespread use, a comparative performance evaluation of these bolt systems has not been done under similar geologic conditions. The performances of three commonly used primary bolt systems were investigated: fully grouted passive rebar, fully grouted tension rebar (using two speed setting resin), and resin-assisted rebar with mechanical anchors. In order to investigate the performance of these bolts, strain gauged bolts of all three types were installed at three different coal mines as part of a larger research project funded by the National Institute for Occupational Safety and Health (NIOSH). This paper addresses the initial installation bolt loads measured at these mines. Analysis of the data showed much lower installed loads on active bolts than is traditionally assumed. It appears that the active load on bolts bleeds off relatively quickly under geologic and operational conditions similar to those at the studied mines. The data also showed that within a short time span after installation, the measured loads on active and passive bolts did not differ significantly. This paper compares the results from over 20 bolts of each bolt type that were all 1.8-m (6-ft) -long, 20-mm (0.804-in) nominal diameter Grade 75 rebar and discusses the relevance and shortcomings of the data and bolt performance.

Jan 1, 2011

By C. Srinivasan

Microseismic emissions are generated by deformation and cracking of rock around an opening inside a mine. The rock tends to achieve equilibrium in a new geometry under changing stress conditions was found to provide useful clues to the impending roof falls and ground instability. The typical characteristics of these microseismic event patterns is shown to be of diagnostic value in sensing in advance rook fall that invariably follow such events. In most of the longwall faces, the main problem faced was due to strata behavior in the presence of massive sandstone bed, which is generally difficult to cave. Microseismic monitoring system was used to monitor strata behavior during longwall mining operation at Rajendra underground coal mine of South Eastern Coal Fields limited (SECL). More than 44,000 microseismic events with local magnitude between -3.4 and 0.5 were recorded during the monitoring period from September, 2001 to March 2003. Analysis of these events was correlated with respect to roof falls. The time series of range of source parameters such as Radiated energy, seismic moment, Energy Index, Seismic Schmidt number, time of occurrence and location of fractures before and during roof fall exhibit qualitatively distinct patterns about six hours before roof falls. &ong the several seismic parameters investigated the microseismic event rate as precursor was found to be most significant indicator of an impending roof fall. The results are discussed as case study in this paper.

Jan 1, 2005

By Andre Vervoort

The roof in coal room and pillar panels is normally stratified and can be thought of as beams or plates supported by the pillar sides in the roadways and by pillar corners in the intersections Underground measurements showed the effect of the face advance on the additional total movement of the roof skin and on the relative movement between various layers in the roof. The latter consists of the opening of bedding planes and of the lateral sliding of layers over one another. Both phenomena increase locally the axial load along full column anchors. Four models have been used to come to a better understanding of the roof behavior: a beam either clamped above the pillar side or laying on the pillar sides and a three-dimensional boundary clement model with and without bedding planes. The shape ref the curvature of the roof deflection is host approached by a clamped beam: the other models overestimate the movement at the sides. The largest roof deflection for a given Young's modulus is estimated by the model incorporating bedding planes. This model estimates that the bed separation occurs close to the face (within the first meter) and within 0.2 m of the sidewalk. In some simulations, openings are even recorded just ahead of the face. Further underground measurements should focus on these findings, as the effectiveness of the support is directly related to the amount of bed separation and sliding, which have occurred prior to the support installation and which still cart occur abler installation.

Jan 1, 2000

By David Bigby

Rock Mechanics Technology has developed an intrinsically safe remote reading telltale system which allows up to 4 sets of 100 dual height, water diverting telltales in a mine roadway to be remotely monitored from a surface PC. The system has US MSHA approval and European ATEX approval for use in gassy mines. A successful full-scale application of the system employing 67 telltales was completed in a 1300m long maingate roadway during retreat of 183.0 longwall panel at West Mine in Germany between June 2001 and October 2002. During panel retreat a number of "teething" problems associated with the system were identified and resolved, the chief problem being associated with cable connection corrosion due to the unforeseen use of sprayed calcium chloride in the roadway. This paper describes the experience of employing the system at the colliery from the perspective of both the user and the manufacturer, and the improvements and developments which have resulted. The paper also presents examples of roof movement data recorded by the system, including data from behind the retreating longwall. The high resolution and data recording rate possible has resulted in particularly interesting information on roof behavior within the longwall front abutment area and behind the face. The paper also describes a series of new transducers and extensometers for the mining industry which employ the same physical principles and similar electronics to the remote reading telltale system. These have been applied in a variety of mining and tunneling environments worldwide over the last two years.

Jan 1, 2003

By Gabriel S. Esterhuizen

"Cable bolts are sometimes used in low-seam coal mines to provide support in difficult ground conditions. This paper describes cable bolting solutions at two low-seam coal mines in similar ground conditions. Both mines used support systems incorporating cable bolts as part of the primary support system. Two original cable bolt based support systems as well as two modified systems are evaluated to estimate their ability to prevent large roof falls. One of the support systems incorporated passive cable bolts, while the other used pre-tensioned cable bolts. The results and experience at the mines showed that the modified systems provided improved stability over the original support systems. The presence of the cable bolts is the most important contribution to stability against large roof falls, rather than the details of the support pattern. It was also found that a heavy steel channel can improve the safety of the system because of the ‘sling’ action it provides. Additionally, the analysis showed that fully-grouted rebar bolts load much earlier than the cable bolts, and pre-tensioning of the cable bolts can result in a more uniform distribution of loading in the roof.INTRODUCTIONCable bolting is sometimes used as primary support in coal mines experiencing difficult roof conditions. In low-seam mines the flexibility of the cable bolts allows greater length supports to be installed near the advancing face without the use of couplers. When used as primary support, the cables are typically installed in the same row as fully grouted bolts, replacing two or more of the bolts in each support row. A heavy steel channel may be used as a strap to spread the support load over a greater portion of the roof. Historically, the Mine Safety and Health Administration (MSHA) has not allowed widespread use of partially grouted un-tensioned bolts (e.g., passive cable bolts) for primary support; however, pretensioned cable bolts have been accepted.Various solutions using cable bolts as primary support were attempted at two low-seam coal mines in Western Pennsylvania that were experiencing difficult roof conditions. Both mines originally used fully grouted rebar bolts as primary support and cable bolts as supplementary support. It was found that when a large roof fall occurred, the cable bolts may be contained within the dome of fallen rock. As problematic roof conditions continued to exist, both mines decided to use cable bolts as part of the primary support system. The cable bolts were located near the ribs of the entry, to increase the likelihood that they would be anchored outside the dome of potentially unstable roof. The cable and rebar bolts were installed on a heavy steel channel that acts as a ‘sling’ to distribute the load across the width of the entry. At the first mine, Mine A, pre-tensioned cable bolts were used while at Mine B, un-tensioned cables were used. The two support systems consist of essentially the same support components installed in different patterns and with varying degrees of pre-tension."

Jan 1, 2015

By Alan D. Smith

[A standardized checklist in a questionnaire format, was established to investigate selected factors associated with coal nips roof falls, as derived from an intensive review of the literature. A plot study was undertaken to aspect and explore possible statistical relationships that may exist with these parameters. the Purposes of toe study were to: 1. Study in a systematic and empirical fashion selected parameters that may be capable of differentiating characteristics of roof falls; 2. Obtain some predictive indices cased on selected physical and management related variables so that predictions of future problems associated with mine roof falls can be completed, prior to its actual occurrence. Accomplishment of these goals should result in valuable guides to the mining engineer in scheduling exploration work and 4 determining economic feasibility of certain ground control and .lining pro and practices. The parameters associated with mine roof failure that where included in the questionnaire are: working section, county, spar., orientation degrees), pillar dimensions width, length), seam thickness, roof fall dimensions (length, width, surface area, volume), shape of fall (arch, dome, laminar), thickness of thinnest immediate layer, lithology of the first four i.e.-diate roof layers, thickness of h e first four immediate roof layers, type of initial support systems before failure, type of resupport system after failure, length and spacing of bolts in use before failure, length and spacing of bolts planned after allure, presence of .cater, time failure after It coal excavation, distance t3rest ace, physical operation during, time of coo failure, location of the roof fall entry failure occurred ence of sloughing of ribs before failure, and presence of floor heave condition before failure. The typical roof fall had an average roof spar of 20.3 feet, -06 feet depth o coal seam, occurred 136 feet from nearest face, coal seam thickness of inches, p--ar :width off 45 feet surface area D' roof fall 1151 ft2, mainly lamin- shaped, previously rat fore fall between good to very good, little floor heave presence, usually cracks before the fall about 40 percent of reported cases, shales in most of the immediate layers, and usually located in an entry or intersection. in addition, multiple linear regression techniques were employed in the testing process of 18 major research hypotheses in a search for relationships among the various parameters studied of which were found to be significant, once corrected for multiple comparisons.]

Jan 1, 1984

By Charlie Li

A cut-and-fill mine stope, located at a depth of about 1000 m in a lead-and-zinc mine, was closed down because of large roof convergence and fractures appearing on the hanging wall. The instability problem was owing to the relatively low strength of the rock subjected to high in-situ stresses. Extra reinforcement was required to secure the stope so that the remaining ores in the stope could be mined. Assessment of the fracture mode in the country rock surrounding the stope was carried out and then the reinforcement de- sign was worked out. It was proposed that the unstable section of the stope would be reinforced by bolt-shotcrete ribs as well as selective long bolts. The philosophy of the design was to hold up the fractured country rock by bolts and shotcrete so that a load-bearing arch could be formed in the roof and in the hanging wall. Six shot- Crete ribs were set up in the unstable section of the stope. Displacement measurements showed that the roof convergence reduced from about 2 &day to the ordinary creeping level, about 0.25 &day, immediately after the reinforcement operation. Six month later, the hanging wall collapsed into the stope in a place just outside the reinforced section, which indirectly proved the effectiveness of the bolt-shotcrete ribs in reinforcing the fractured country rock. This case showed that an appropriate rock mechanics assessment would form a solid base for reinforcement/support design. It also provided an evidence for the philosophy of the reinforcement by bolt-shotcrete ribs - establish a load-bearing arch in the rock.

Jan 1, 2005

By Kudret Tutuk, Serkan Saydam, Sungsoon Mo

"This paper presents an overview of the floor heave management at the Glencore Bulga Underground Operations and investigates the contributing factors to the behaviour of the floor. The mine experienced a number of major floor heave events in gateroads on development. As the longwall face approached the roadways, the magnitude of floor heave frequently increased, while new floor heave also developed. Furthermore, severe floor heave events took place along the longwall face. The most observed failure mode was buckling. While regular floor measurements were conducted to better understand the nature of the phenomenon, and various measures were considered to control the deformation of floor, the mining height was increased for the predicted floor heave domains, which facilitated effective management of the floor issues. The experience in the mine indicates that mainly high horizontal stresses with greater depths of cover and certain types of floor lithology configuration are likely to contribute to the failures of floor strata.INTRODUCTIONThe Glencore Bulga Underground is located in the Southwest of Singleton in the Hunter Valley of New South Wales, Australia. Blakefield South, part of Bulga Underground, commenced longwall mining in 2010, extracting coal from the Blakefield seam, while the overlying longwall panels were previously mined from the Whybrow seam. The coal seam ranges from 4.5 m to 8.0 m thick with the mining heights varying from 2.9 m to 3.5 m. The longwall panels are 320 m and 400 m wide and up to 3.5 km long.The mine experienced a wide range of floor issues around longwall panels LW7 and LW8, both 400 m wide. For instance, the concrete floor in the travel road failed and lifted as the longwall retreated in close proximity as can be seen in Figure 1. Figure 2 shows the beam stage loader (BSL) buried into the lifted floor, and Figure 3 shows a timber prop distorted due to the movement of the floor. In addition, severe deformation of the floor along the longwall face impeded the longwall operation, as shown in Figure 4."

Jan 1, 2018

By John Kucish

Roof bolting in the Pittsburgh Coalbed takes many forms today: coupled partially grouted bolts, fully grouted rebar, passive cable bolts, tensioned cable bolts, and torque tension rebar. The Federal No. 2 Mine of Peabody Energy has recently made a significant advance in longwall headgate primary roof support, with the change fiom an 8 ft long coupled partially grouted bolt to a 6 ft long torque tension system. The coupled partially grouted bolt consists of a 4 ft long 0.804 in diameter rolled deformation bar thread coupled to a smooth 718 in headed bar. The coupled partially grouted bolt is anchored into a 1 318 in borehole with 4 ft of high speed resin. The 718 in diameter smooth bar is tensioned by rotation into the treaded coupler, upon setting of the resin, compressing the immediate roof. The change was initially driven by occasional failure of the coupled partially grouted bolt at the threaded coupler, due to lateral movement caused by horizontal stress. A fully grouted % in diameter torque tension bolt, in a 1 in borehole, was proposed as a cost effective primary bolting for the high horizontal stress conditions. The upper 2 112 ft of the rebar is anchored in fast set, medium viscosity resin and the bottom 3 K ft is anchored in slow set, special low insertion force resin. The lower end of the rebar is threaded with a nut that permits the counter clockwise spinning of the bolt to mix the resin, at maximum rotational torque. Upon setting of the high speed top resin, the nut is spun clockwise to tighten the nut against a metal dome plate. The plate is forced against the roof to compress the immediate roof, A complete headgate entry has been successfully supported with the torque tension system. The mining of the adjacent longwall panel was completed in September 2004. The torque tension system provided a 25% savings over the previously employed coupled partially grouted bolt system.

Jan 1, 2005

By Rajendra Singh

In India, pillar mining is contributing more than 90% of underground production which involves extraction of a part of coal from bords with pillars around as natural support in the development stage. #Liquidation of these pillars with splitting and stooking, broken nature of face during mining under complex geomining factors like massive roof, varying treatment of goaf and over or underlying workings result in high stresses and deformation in and around the neighbouring piilars, causing operational problem and hazards to mine safety. This paper suminarises the results of three case studies of depillaring under shallow depth with or without stowing. Assessment of nature and amount of mining induced stresses and deformation was done under these conditions, by insitu instrumentation and observation at three depillaring panels of Girmint. Samla and Lachhipur collieries of ECC at 54, 90 and 110 m depth cover respectively. The value of induced stresses and associated deformations was comparatively low in well caved and stowed waves, whereas for massive roof the roof fall followed overriding of pillars and stooks, with very high value of induced stresses and deformaton in absence of stowing. The stress in the centre and outer edges of the pillars changed with respect to depillaring face advance or splitting of pillars. The caving panel of Girmint colliery under weak coal measure formation, showed maximum induced stress in the pillar at 4 m distance from the face which was 1.2 times (16.6 kg/sq.cm) the preminlng stress of the area. The main roof fall over partially stowed goaf of Lachhipur colliery under massive roof strata caused overriding of pillar after crushing 39 stooks of 7.5 x 7.5 sq.m in rythmic sequence with development of 133lsq.cm maximum induced stress. Well stowed Waf of the same panel reduced this value of abutment stress to 2.3 times (65 kg/sq.cm.) body stress after 40 m further advance of the face from the crushed zone. The depillaring at Samla colliery even under massive roof strata induced low stress, equal to 0.8 times field stress only under the same condition with stowed goaf. The studies revealed the effectiveness of stowing in the goaf over loading of pillars and stooks.

Jan 1, 1990

By Winton Gale

"Rock and coal fractures and micro seismic vibration are common occurrences during development mining. It is very uncommon for coal and rock to be propelled into the roadway during normal mining operations. However, such occurrences do occur and appear to require significantly more energy than is available from strain energy release during coal cutting. The sources of energy, which can contribute to the propulsion of coal from the face or ribs, are typically strain energy from the surrounding ground, seismic energy from a rapid rupture of the ground in the vicinity, or rapid expansion of gas from within the burst source area.The aim of this paper is to briefly review the bursts that could be related to strain energy or seismic energy. However, the greatest emphasis is placed on the effect that gas within the coal could play in moderate to gassy mines.It has been found that the bursts related to the expansion of gas can occur in coal and stone. The volume of gas involved in coal bursts is typically lower than in gas outbursts; however, the process is generally similar.INTRODUCTIONA coal burst is defined as a rapid expulsion of coal (and potentially gas) from the boundary of the roadway. The volume of a burst can be variable, but volumes above 10-50m3 are noted and cause significant disruption to operations.Rock and coal fracturing is common about roadways, particularly under the influence of elevated stresses, either tectonic or related to mining abutment stress. Shear fracture is very common; however, it is very uncommon that the coal is propelled from the face or ribs as a result of fracture of the material. The nature of rock fracture about roadways under elevated stress is presented in Figure 1.A burst requires energy to propel the coal or rock from the rib or face of the roadway. The depth of material impacted may vary from 0.5m to greater than 3m inside the roadway boundary. The strength of the ground in this zone is variable depending on the nature of the coal seam (or surrounding material). Typically, this material has significant residual strength as confinement increases into the ribside.The energy required to propel this material is typically in addition to that which is associated with normal fracturing about the roadway."

Jan 1, 2018