Search Documents

By Rocky Wu

Rock bursts are one of the greatest challenges to ground control in the mining industry. With increasing mining depth and mining scale, there are more and more industry requirements on yielding rock support. Since 2008, Jennmar has been conducting large scale research and development works to develop a technically reliable and cost-effective yielding rock bolt. This paper introduces a new yielding rock support: the Yield-Lok bolt. The bolt is characterized by the designed yielding ability to produce 150?250 mm (6?10 in) of deflection at 8?10 metric tons (MT) (7.9?9.8 t) loads for every 16.4kJ (12,096 ft lb) energy input. The bolt?s performance characteristics are consistent through multiple and varying amplitude of impacts. In this paper, the design criteria of the bolt and the principle of performance are described; the dynamic testing results are discussed; and the features and application of the bolt are presented.

Jan 1, 2011

By Daniel S. Mazzei

This paper will be a general discussion of surface flooding considerations as they affect mining facilities site selection, based primarily on experience with several such problems with which MSHA's Bruceton Technical Support staff has been involved. The detailed analytical procedures used in arriving at engineering solutions of these problems will not he presented here; the emphasis is on drawing attention to this additional aspect of mine design which hitherto has been largely overlooked due to insufficient awareness, information and criteria. The paper's purpose is to stimulate thought and offer guidance concerning the selection of sites for mining facilities in light of the potential for flooding problems caused by surface waters. Flooding by surface waters, would generally not be a serious consideration in areas of relatively low topographical relief, i.e. flat lands, although there are exceptions to this rule, for example, in Western areas where flash flooding is a major concern. Therefore, this discussion will mainly apply to areas where the severity of surface flooding would be amplified by the topography-large, well defined watersheds of considerable relief, i.e. mountainous areas. In these regions, steep valley walls cause any rainfall to flow quickly into the relatively narrow valley bottoms. These valley bottoms provide little flow area during storm conditions, so deep and rapidly flowing streams result.

Jan 1, 1982

By Robert Trueman

This paper details the results of an assessment aimed at understanding the shield loading mechanisms associated with strata-related issues on a longwall face. Shield load cycle analysis theories developed by the authors were used to quantify the interaction between the shields and strata. Shield pressure data was back-analyzed using a version of the Longwall Visual Analysis (LVA) software that has been extended to enable efficient load cycle analysis to be undertaken. The software outputs enabled the shield strata interactions to be characterized. The results of the analyses indicated that the major cause of the roof falls was high-level periodic weighting, resulting in periodic shield overload. Exploration borehole data was analysed to identify and characterize the overburden unit that was the likely cause of the shield overloading.

Jan 1, 2011

By John Shepherd

Pillar extraction carried out using various methods (split and lift, Wongawilli and old Ben) involves the formation of narrow fenders (commonly 7 m of coal) formed by driving "splits" for lifting off with a continuous miner. The strata above a split and fender adjacent to the goaf consists of a cantilever beam (usually >3 m thick) that extends from the solid coal and bridges across the fender. Lifting off the fender from the split in safe conditions depends upon the bridging capability of the cantilever and the fender strength. The nature and competence of the immediate and near roof, the support capability of the coal fender and the presence of faults and or joints can adversely affect the bridging behaviour of the cantilever. Insufficient knowledge of these parameters can lead to extraction under dangerous conditions. Remnants of fenders ("stooks") also support the cantilever and their dimensions are critical to obtain regular caving and goaf falls. Stook area, goaf roof span and roof stand-up time after lifting can be related and only a relatively small increase in Btook area of 10-15 m2 can lead to a significantly increased stand-up time, especially under a massive roof. Such conditions strongly influence the redistribution of abutment stresses and can create increased outbye pillar loading. Based on detailed underground geotechnical investigations, it is concluded that strata caveability, roof cantilever behaviour, fender H:W ratio and remnant stook size are all critical parameters for successful and safe pillar extraction.

Jan 1, 1992

By Hamid Maleki

The U.S. Bureau of Mines implemented a monitoring program in a western U.S. coal mine for the evaluation of both conventional and alternative support systems. The conventional support consisted of 2.5-m-long vertical bolts installed in an 5.5-m-wide entry. The alternative system consisted of 2.5- and 3-m vertical and inclined bolts installed at a higher density during widening of a cut from 3.6 to 5.5 m. Roof deformation, roof stress, rib deformation, and bolt loads were monitored during the 2-month test period. In addition, roof failure patterns and lithology were characterized within the six-entry main test section. Results were analyzed using roof deformation and failure profiles, roof stress profiles. bolt loading and bending moment diagrams, and numerical models. The mechanics of roof deformation, failure, and support reaction in three zones in the mine roof were characterized. Significant improvements were shown in roof stability in the section using the alternative system. Results are encouraging and indicate the effectiveness of alternative support systems and excavation techniques for limiting inelastic deformation of roof in highly stressed underground mines.

Jan 1, 1994

By Ry Stone

"There have been many design practices utilised within the coal mining industry to arrive at the minimum densities of primary ground support required during roadway development. This paper demonstrates the practical use of empirical databases, and focuses on the main drivers for ground support as demonstrated in conceptual models.Golder Associates’ empirical databases used for ground support include a Primary Roof Support Database and a Primary Rib Support Database. Both are based on successful ground support designs installed in mines in Australia, the US, the UK, South Africa, New Zealand, and Europe. The term “successful” refers to those designs that were used on a repeated basis for the purpose of roadway development.The Primary Roof Support Database indicates that the major factors influencing successful roof support designs are roof competency, expressed as the Coal Mine Roof Rating (CMRR), and in situ stress. As roof displacement is essentially a function of horizontal stress and roof competency, in order to provide some form of measure as to the likely magnitude of roof deformation during roadway development, the depth of cover is divided by the CMRR to arrive at a “Stress Strength Ratio” (SSR). The database indicates that the higher the SSR, the greater the likelihood that the roof will require higher densities of support.In regard to the Primary Rib Support Database, it is evident from the current database that the primary factors affecting the capacity of rib support required for a successful design are roadway height and depth of cover. In order to provide some form of measure as to the likely magnitude of rib deformation during roadway development, the depth of cover is multiplied by the height of the roadway to determine a “Rib Deformation Rating” (RDR). Similar to the roof, the database indicates that the higher the RDR, the greater the likelihood that the rib will require higher densities of support.These databases have been used to help determine the minimum primary ground support designs required at many mine sites in Australasia, Europe, and the US. This paper will demonstrate the effectiveness and practicality of these databases at two selected mines in Australia and the US.In order to improve the Primary Rib Support Database, this paper will also propose a new rib deformation rating based on the addition of site specific coal strength data for the Australian mines. The proposed rating attempts to capture the main variables that define the behaviour of a buckling column."

Jan 1, 2015

By Frank E. Chase

Geologic structures have been responsible for numerous underground accidents and fatalities, and are a constant-source of down time. During - longwall mining, ground control problems associated with geologic anomalies are aggravated by the abutment pressures which develop as the panel is retreated. Therefore, it is imperative that these structures be recognized and properly supported in head- and tailgates. Fractures, faults, clay veins, igneous dikes, and ancient stream channels (paleochannels) disrupt the lateral continuity of the mine roof and can cause falls in gateroads. Horsebacks and kettle bottoms are also hazardous because abutment pressures tend to "pop out' these structures into the gateroads. This Bureau of Mines investigation describes the physical characteristics associated with hazardous geologic structures, identifies the coal fields where-they have been observed, and, where possible, suggests support strategies and other mine plan modifications to help minimize their effect.

Jan 1, 1990

By Douglas Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because it can result in failures of ground that lead to both injuries and death. Spokane Research Laboratory personnel investigated electromagnetic (EM) emissions in a deep underground mine in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results suggest that (1) there is no increase in the number of EM emissions prior to recorded seismic activity, (2) some EM signals are generated during blasting, (3) interference from mine electrical sources mask seismic-generated EM signals, (4) EM emissions do not give enough warning (compared to seismic monitoring) to permit miners to leave a stope, (5) the distance an EM signal can travel in the rock is between 17.7 and 39.6 m (58 and 130 ft), and (6) current data acquisition systems do not differentiate between EM signals generated from seismic activity and random mine electrical noise. These results preclude monitoring EM emissions as precursors of impending catastrophic ground failure.

Jan 1, 2004

By Francis S. Kendorski

Rock reinforcement has been in widespread use and generally has been accepted in underground mining and tunneling since the 1950s. The first rock reinforcement technologies employed were mechanical anchors such as split wedges or expansion shells with 5/8-inch-diameter steel bolts. Failures occurred in weak strata which provided poor anchorage or in ground with corrosive waters. Friction rock fixtures consisting of relatively thin-walled tubes have been in use for about 15 to 20 years. While generally performing adequately, longevity problems have developed from corrosion in water bearing ground Longevity of rock reinforcement is much enhanced with grouted bolts. Portland-cement-grouted rock reinforcement has been in use since the mid-1950s, primarily in funneling and other civil engineering underground construction. Tests of decades-old installations have revealed few problems except in ground with aggressive waters. Polyester-resin-grouted rock reinforcement was introduced in the United states to musing in the late 1960s and to tunneling in the early 1970s. Experience from 30 years of resin-grouted bolt installations and field tests have identified longevity problems associated with degradation of steel reinforcing bars, but in generally unusual situations. Improvements continue in resin chemistries, packaging, corrosion protection, grout quantities, and mixing and distribution in the drilled hole to achieve long-term performance. Specific case histories cited with resin- or Portland-cement-grouted rock reinforcement longevity or performance problems, upon close examination, reveal that the causes of the problems were qualify control procedures being inadequate and not in accordance with good practice. Manufacturers' recommendations and engineering specifications, if followed in the field, and with competent inspection and supervision, would have prevented must, if not all, reported longevity or performance difficulties.

Jan 1, 2000

By Claude A. Goode

Large quantities of high grade coal exist in thick seams in the United States. Many of these thick seams are too deep to be surface mined and do not lend themselves readily to underground extraction. To develop the new mining technology required to effectively mine thick seams, the Department of Energy has entered into a Cooperative Agreement with Mid- Continent Resources, Inc. to demonstrate the multilift longwall mining technique in a 28 foot-thick seam at their L.S. Wood No. 3 mine near Redatone, Colorado. The seam will be extracted in two lifts, with a 5-foot natural partition of coal left between the upper and lower lifts. Proper selection of face supports is critical to the success of this project. Specifications were defined for the roof supports, and it was concluded that the supports selected must provide full coverage, yield at the legs, and have a 60-inch push- out cantilever that can be set at any position under full load. A Hemscheidt two-leg shield was judged as the best qualified candidate and was selected for the multi-lift trial.

Jan 1, 1981

By Yingxin Zhou

Data from these field studies and previous case study data have been combined to define ultra-dose seam mining environments and relate them to observed failure conditions. A rating system for ultra-close multi- seam design has been developed and field studies have verified the applicability of the design criteria according to geologic structures, lithology and spatial data. This rating system has been combined with design and depth considerations to create a protocol for quantitatively predicting potential damage in ultra-dose seam mining conditions. A brief discussion of the characteristics of ultra-dose seam mining and its related failure mechanisms is also presented

Jan 1, 1990

By Yi Luo

Accurate mechanical and geological information of the roof strata is vital for roof bolting design in underground mines. In order to obtain such information in a timely manner, a research has been under way to develop a technology for mapping the roof geology using the drilling parameters acquired during the roof bolting operations. In this paper, a systematic approach has been proposed for determining the rock strengths using the acquired real-time drilling parameters. A computer simulation program based on the mathematic model has been developed to verify the approach and to study its sensitivity. The method has been used to interpret the acquired drilling data.

Jan 1, 2002

By Dongfeng Yun, Zhu Liu, Wendong Cheng, Zhendong Fan, Dongfang Wang, Yuanhao Zhang

"For the purpose of studying the strata behavior due to multislicing top coal caving longwall mining along-the-strike direction in steeply dipping extra thick coal seams, the shield support pressures of the upper and lower slices of Panel 37220 in Dongxia coal mine were monitored using the KJ513 dynamic monitoring system. The set up rooms adopted the ""horizontal line-arc segmentinclined line"" form and used different types of shield supports. The results showed that the strata pressure of upper slice Panel 37220- 1 changed slightly along the strike direction, while along the dip direction it exhibited strong to weak pressure from bottom to top. The first weighting interval oflower slice Panel 37220-2 was about 60.Sm, and the average periodic weighting interval were about 22.6m. The strata behavior of Panel 37330-2 exhibited a spatiotemporal characteristic in that periodic weighting occurred first in the middle-upper part, followed by the middle and upper parts, arc segment, and finally the lower part. During the periodic weighting, the weighting interval and intensity also exhibited strong space characteristics. The average dynamic load coefficient was 1.48 and the maximum lateral pressure of the side shield was 900Kn1000kN.INTRODUCTIONThe steeply dipping coal seams account for about 20% of proven reserves and 10% of output in China (Wu, et al, 2014). About 50% of coal mines in the western China have steeply dipping seams, and are mainly distributed in Sichuan, Gansu, and Chongqing. When the steeply dipping seam employs longwall mining along the strike direction is employed, the waste rocks fill the gob nonhomogeneously along the dip direction, the deformation and caving of surrounding rocks exhibit obvious asymmetry and spatio-temporal characteristics with particular and complex strata behavior. In recent years, many research on strata behavior due to multi-slicing top coal caving longwall mining along-the-strike direction in steeply dipping extra thick coal seams have been performed with significant results (Shi, 1999; Wu, Xie, and Ren, 2010; Wu, Xie, Wang, and Ren, 2010). However, there has been a complete lack of research on monitoring the strata behavior due to multi-slicing top coal caving longwall mining in steeply dipping extra thick coal seam. Therefore, the strata behavior of multi-slicing panels 37220-1 and 37220-2 was systematically investigated in this research."

Jan 1, 2016

By Ashok Kumar, Rajendra Singh, Petr Waclawik

High-grade coal is locked in the shaft protective pillars at 900 m below surface in the Czech part of Upper Silesian Coal Basin. To optimise recovery of coal from the larger size shaft protective pillar, room and pillar (called bord and pillar in India) is trialled to further develop these on smaller pillars. This development followed a constant gallery width of 5.2 m and 3.5 m height. The monitored pillar size in the first developed panel varied from 860 m2 to 1225 m2 of area. The stability of these pillars (i.e., natural supports) at this depth of cover is observed to be a vital issue to control ground movement and safety of the surface structures. A simple calculation of safety factor revealed that application of an empirical method for estimating size and shape of the pillar is inappropriate due to complex geo-mining conditions of the site. Accordingly, geo-technical instruments are installed in the panel for monitoring the stability of the diamond shaped pillar at different stages of the development. Extensive monitoring of the pillar behaviour by these instruments provided an important set of data for such optimum recovery. An established process of simulation-based pillar strength estimation is often used by the mining industry, but calibration is generally done with the help of empirical formulation. However, for the deep-seated pillar, the strength suggested by the existing empirical formulations (except the CMRI formula) is found to be much different from the instrument observations. Using a study conducted at Czech hard coal mines, an attempt is made to develop a strain-softening-based numerical modelling approach to assess pillar performance at deeper cover. The recorded value and nature of the pillar spalling in the field along with the CMRI formula are used to calibrate the developed simulation approach. An assessment of the stability of the developed pillars using simulated models did not indicate any collapse of the natural supports. This paper briefly presents difficulties in pillar design at great depth of cover and field and simulation results of pillar strength estimation in Czech hard coal mines.

Jan 1, 2018

By Dion Pastars

Kestrel Coal has undertaken a surface-to-seam consolidation program of faulted ground prior to longwall retreat in the 304 panel. Micro fine cement is used to improve the rock mass quality and therefore reduce the risk to personnel and equipment whilst increasing previously assumed sterilised reserves. The program is based on information attained from previously successful grouting campaigns in the Queensland coal area and follows the decision making process to ensure there is sufficient spatial permeation of cement across the faulted area. This data is used to assess the residual risk to the business in terms of health, safety and production

Jan 1, 2007

By Jesse Puller, Ken W. Mills, Owen Salisbury

"An underground coal mine located in New South Wales has a target coal seam located 160-180 m deep directly below a 16-20 m thick conglomerate unit that has been associated with significant periodic weighting events on the longwall face. As part of the investigations to better understand the causes of periodic weighting at the mine, inclinometers capable of measuring horizontal shear movements through the full section of the overburden strata were installed ahead of mining at two locations approximately 1 km apart above the centre of two longwall panels. These inclinometers were monitored as the longwall approached each site. This paper presents the details of the installation, the results of the inclinometer monitoring at both sites, and the insights that these measurements provide for overburden behaviour about longwall panels.Horizontal shear movements were observed to develop on shear horizons that correlate closely across the two sites suggesting a mechanism that is consistent across a large area of the mine. Shear movements were observed to develop on a single horizon near the top of the conglomerate strata that was mobilised almost immediately after initial formation of the longwall goaf at a distance of 425 m ahead of the longwall face. The direction of horizontal movement was consistent with the relief of the major principal horizontal stress. As the longwall face approached each inclinometer, other horizons within the upper part of the overburden strata begin to shear with the upper strata moving toward the approaching goaf more than the lower strata. Within the last 30 m of longwall approach, tilting of the strata associated with the increase in vertical subsidence toward the extracted goaf caused a change in the style of deformation with tilting and reverse shear offsets.INTRODUCTIONLongwall mining is recognised from subsidence monitoring, surface extensometer measurements, and various other observations to cause significant disturbance to the overburden strata directly above the extracted goaf of each longwall panel. Disturbance to the overburden strata beyond the limits of each longwall panel is not so well understood. Subsidence monitoring indicates that horizontal movements beyond the edges of the extracted longwall panel are generally greater in magnitude than vertical subsidence and horizontal movements may extend up to several kilometres from the edge of the panel in some circumstances (Reid 1998, Reid 2001, Hebblewhite et al 2000, Mills 2001, Mills 2014). The mechanics of how these movements are accommodated within the overburden strata is only poorly understood and there are few direct measurements."

Jan 1, 2015

By Tom Blevins, Roland Walker, Jinsheng Chen

"The Dywidag-Systems International DSI Tandem Anchor bolt, with an improved expansion shell-washer design, can substantially reduce potential entry roof falls caused by twisted or deformed expansion shells of the traditional mechanical anchor bolts during installation. In addition, the improved anchorage system can also ensure that a consistent and high installed load is achieved, which is critical for effective beam building under thinly laminated or layered roof conditions. This paper discusses the genesis and anchorage performance of the Tandem Anchor bolt, and analyzes the tension/torque relationship of different mechanical shell anchors using data obtained from both lab and field tests. It also discusses roof bolting mechanisms, roof bolting systems, and factors influencing effective beam building. Finally, numerical modeling was used to analyze the effect of bolt pretension magnitude on entry roof stability.INTRODUCTIONThroughout the history of underground mining, keeping the roof from uncontrollable collapse has been the greatest concern of the miner. Tremendous strides have been made in better understanding, predicting, and supporting the mine roof. This conference has spent the last twenty-eight years sharing information and distributing it to the mining community. A paraphrased statement from former Secretary of Defense Donald Rumsfeld adequately describes the challenges to the mining engineer as it pertains to roof control: it is a study of known knowns, known unknowns, and unknown unknowns. It is the hope of the authors to address some of these unknowns.The paper discusses the development of bolt anchorage systems from dry shells to shells with resin-assisted anchorage. It looks at some of the issues faced with the anchorage shells being used when introducing the insertion pressures caused by resin cartridges. The rationale behind the shell design changes was to compensate for this resin induced stresses.An improved expansion shell assembly (a slotted expansion shell base, a tapered cramming plug, and a novel support nut with tapered top) for mine roof bolts makes up the Tandem Anchor (U.S. Pat. No. 6742966); this minimizes the possibility of twisting seen with traditional mechanical shells and thus prevents springy bolts and shell leaves from breaking. A fully grouted Tandem Anchor bolting system has the advantages of both the pure mechanical point-anchor and the non-pretention fully grouted bolting systems. Once installed, the installed load or pretension will be locked in and never bleed off. Compared with the fully-grouted (2-speed resin) tension rebar bolting system, the fully-grouted Tandem Anchor bolting system can (a) reduce bolting cycle time (about 15 seconds per bolt), boosting coal production and productivity; (b) provide a greater installed load or pretention; and (c) achieve a consistent tension/torque ratio, which gives better bolting quality control. Therefore, a fully grouted Tandem Anchor bolting system is the most effective means to reinforce a weak rock mass intrinsically by the theory of beam building. For thinly laminated or layered roof conditions, a higher installed load or pretention (50% or more of the bolt's yield strength) can make a roof bolting system much stiffer, which results in less roof movement. Numerical modeling results show that the magnitude of the roof's tensile stress and relaxation zone can be substantially reduced under a higher installed load or pretention."

Jan 1, 2010

By John R. Poland, Benjamin Mirabile

"There are significant ground support hazards to both personnel and equipment when longwall equipment must mine through cross-panel entries. Backfilling support strategies are often cost prohibitive. Additionally, it is often very difficult to install backfill material in full contact with the mine roof in backfilled entries. This paper will demonstrate the use of fiber-reinforced concrete crib material as a method for standing support in longwall cut-through entries. Despite conceptions of poor performance in potentially high convergence environments, fiber-reinforced concrete crib material can be used in longwall support environments subject to high abutment loads and convergence. Central to the proper design of these supports is the use of yield material between crib layers and at the mine roof/crib interface. The placement location of cribs within the cut-through entry has a significant effect on the main roof behavior and associated ground conditions in the longwall abutment zones. It is particularly important to engineer the proper load displacement characteristics of the installed crib to support expected ground conditions. The cost of fiber-reinforced crib supports is less than 50% of backfilling methods.INTRODUCTIONThe design and execution of a longwall cut-through is perhaps one of the most difficult and risky endeavors in the field of ground control. The magnitude of abutment loads and potential for ground failure present a significant safety hazard to underground personnel. In addition, there is significant financial risk, with replacement costs of face equipment exceeding $200 million. Faced with these consequences, it is both advisable and common for an engineer to design ground support with a significant margin of safety. This paper outlines a robust support system that possesses a significant margin of safety along with significantly lower costs than most other support systems employed in similar conditions.SITE PARAMETERSThe mine site described in this study operates in the Herrin No. 6 seam in southern Illinois. The seam height is typically 76- 84 inches. Mining height in gateroads and mains is typically over 96 in, and typical mining height on the longwall face is 82 in. The overburden depth is 950-970 feet in the area of the longwall cutthrough."

Jan 1, 2016

By Pinnaduwa H. S. W. Kulatilake

To exploit an underground mine effectively and safely, it is important to have a good understanding of the geotechnical behavior of the rockmass surrounding the underground mine excavation. The aim of this study was to investigate, at the threedimensional level, the geotechnical behavior around a tunnel excavated in a metal mine in China. A three-dimensional numerical model was built by using the 3DEC software package to simulate a tunnel excavation under a high in situ stress condition and by relying on the information available on lithology, geological structures, in situ stress measurements, physical and mechanical properties of intact rock, discontinuities, and interfaces between different rocks. The authors also investigated the effect of the discontinuity network, possible intact rock and discontinuity parameter variability, representation of rock masses as discontinuum or equivalent continuum material and rock support system on the deformation, and stability around the tunnel. A very good agreement was obtained between the collected field deformation monitoring results and the results of the conducted numerical stress analyses with appropriate geomechanical property values.

Jan 1, 2013

By Peter Zhang, Gary Deemer, Rod Lawrence, Scott Peterson, Scott Wade, Mike Mishra, Rick Smith, Robert Bottegal, Ed Zeglen

"Thinly-laminated silty shale that falls like ""stack rock"" is always difficult to support in underground coal mines. With thin laminations of 2.5 to 52 mm (0.1 to 2 in) thick and weak bonding between laminations, the roof is much weaker under horizontal stress than under vertical load. Buckling of thin laminations and cutters are common signs of initial failure for this type of roof. When a roof fall occurs, it is mostly above the primary bolted horizon with a fiat top and steep breaking angle above the pillar ribs. Because silty shale is brittle, roof falls mostly develop without significant roof sagging. With thick, laminated silty shale, it is difficult to build a strong solid beam with short primary bolts. Longer bolts, straps, and supplementary cable bolts are required. Since installation of longer primary bolts in low seam mining is operationally inefficient, supplementary bolting is important to maintain overall roof stability. The bolting plan should also be chosen based on the geologic hazard map, which indicates the distribution and thickness of laminated silty shale, as well as the transition areas.To effectively support the thinly-laminated silty shale roof, an area with the same type of roof in a low seam mine was monitored for approximately four months. The mine had experienced roof falls while using different bolting systems and mine orientations in past years. The roof support in the area was studied through geologic mapping, roof scoping, and testing of different bolting plans. This paper presents the roof failure characteristics of the thinly-laminated silty shale, the correlation between failure and geologic condition, an evaluation of different bolting plans, and the requirements for primary and supplementary bolting for the silty shale roof.INTRODUCTIONThinly-laminated silty shale that falls like ""stack rock"" is always difficult to support in underground coal mines (Peng, 2007). With thin laminations of 2.5 to 52 mm (0.1 to 2 in) thick and weak bonding between laminations, the roof is much weaker under horizontal stress than under vertical load. Buckling of thin laminations and cutters are common signs of initial failure for this type of roof. When a roof fall occurs, it is mostly above the primary bolted horizon with a fiat top and steep breaking angle above the pillar ribs. Because silty shale is brittle, roof falls mostly develop without significant roof sagging. In low seam mining, it is difficult to install longer primary bolts, so supplementary bolts have to be installed to maintain overall roof stability. To effectively support the thinly-laminated silty shale roof, an area with the same type of roof in a low seam mine in western Pennsylvania was studied for approximately four months."

Jan 1, 2010