Search Documents

By Behdeen Oraee, Amirhossein Bangian, Kazem Oraee

"Determination of the optimum design of chain pillars has a significant effect on the economics and safety of longwall operations. Most pillar design formulae are based on empirical methods and supplemented by local experience. They therefore lack versatility of application under different geotechnical conditions.In this paper, in order to illustrate the shortcomings of the above, a typical real coal pillar in Tabas coal mine has first been studied and the conventional formulae have been used to determine the optimum dimensions. The results show that a wide difference exists between the predicted and the real field data. The Oraee-Hosseini formula has then been applied to this mine in order to determine the optimum design. The results from this formula demonstrate a close fit between the theoretical VALUES (and those produced by laboratory tests and in practice. It is further demonstrated that the wide discrepancy between the results obtained from the two formulae is attributed to the dissimilarities between geotechnical conditions of Tabas and the original regions whose data were used to devise the empirical formulae.It is finally concluded that the application of numerical simulation methods and experimental equations together with engineering judgment used by the mining design engineer, will provide the most accurate design characteristics.INTRODUCTIONLongwall is an underground mining method which has a high rate of production capacity and mechanization ability. This mining method, which is appropriately applied for soft rock fiatlying bedded ore bodies, gradually became a widespread mining method amongst European coal mines at the beginning of the 19'h century. It was then applied in some of the U.S. coal mines with the development of self advancing support mechanisms in early 1960's (Oraee, 2001).Underground coal production around the world using Longwall mining method doubled during 1990s. The main reasons for this improvement were: the high level of mechanization, increased 10 safety, adequate design of panels, and well designed ventilation systems (Peng, 2006)."

Jan 1, 2010

By Morgan M. Sears, lhsan B. Tulu, Ted M. Klemetti

"Why do some room and pillar retreat panels encounter abnormal conditions? What factors deserve the most consideration during the planning and execution phases of mining and what can be done to mitigate those abnormal conditions when they are encountered? To help answer these questions, and to determine some of the relevant factors influencing the conditions of room and pillar (R&P) retreat mining entries, four consecutive R&P retreat panels were evaluated. This evaluation was intended to reinforce the influence of topographic changes, depth of cover, multiple-seam interactions, geological conditions, and mining geometry.This paper details observations made in four consecutive R&P retreat panels and the data collected from an instrumentation site during retreat mining. The primary focus was on the differences observed among the four panels and within the panels themselves. The instrumentation study was initially planned to evaluate the interactions between primary and secondary support, but produced rather interesting results relating to the loading encountered under the current mining conditions. In addition to the observation and instrumentation, numerical modeling was performed to evaluate the stress conditions. Both the LaModel 3.0 and Rocscience Phase2 programs were used to evaluate these four panels. The results of both models indicated a drastic reduction in the vertical stresses experienced in these panels due to the full extraction mining in overlying seams when compared to the full overburden load. Both models showed a higher level of stress associated with the outside entries of the panels. These results agree quite well with the observations and instrumentation studies performed at the mine.These efforts provided two overarching conclusions concerning R&P retreat mine planning and execution. The first was that there are four areas that should not be overlooked during R&P retreat mining: topographic relief, multiple-seam stress relief, stress concentrations near the gob edge, and geologic changes in the immediate roof. The second is that in order to successfully retreat an R&P panel, a three-phased approach to the design and analysis of the panel should be conducted: the planning phase, evaluation phase, and monitoring phase."

Jan 1, 2016

This paper is not available for inclusion in the Proceedings at the time of printing, but it will be included as an insert.

Jan 1, 1984

By Tex M. Kubacki

On August 6, 2007, the Crandall Canyon Mine experienced a collapse which trapped six mine-workers. An MW 4.1 seismic event was recorded in conjunction with this collapse. An additional 54 seismic events were detected and located in the vicinity via routine processing techniques during the month of the collapse. Waveformbased cross-correlation detection techniques have been used to uncover 1,328 small, previously undetected seismic events which occurred near the collapse area between July 26 and August 9, 2007. This work has resulted in lowering the magnitude threshold of completeness from ML 1.6 to ML -0.5, a 2.1 order-of-magnitude improvement over standard processing techniques. Event locations have been computed using a double-difference inversion. The spatial pattern of events ultimately helps to delineate the extent of the collapsed area. It is shown that many of the large catalogued events (>ML1.6) tend to be closely followed by numerous (often 20 or more) smaller aftershocks. Cluster analysis of the known catalog reinforces prior work indicating the existence of seismic clustering on the east and west sides of the collapse. Research now demonstrates that it is possible to differentiate events related to the main collapse from those related to the rescue attempt following the collapse. The cross-correlation techniques described herein greatly improve the ability to detect small mining-induced seismic events. These methods may lead to improvements in assessing seismic hazards for conditions similar to those observed at Crandall Canyon preceding the collapse.

Jan 1, 2013

By Esterhuizen S. Gabriel, Su W. H. Daniel, Tulu B. Ihsan, Klemetti M. Ted, Mohammed M. Khaled, Gearhart F. Dave

"A numerical-model-based approach was recently developed for estimating the changes in both the horizontal and vertical loading conditions induced by an approaching longwall face. In this approach, a systematic procedure is used to estimate the model inputs. Shearing along the bedding planes is modeled with ubiquitous joint elements and interface elements. Coal is modeled with a newly developed coal mass model. The response of the gob is calibrated with back analysis of subsidence data and the results of previously published laboratory tests on rock fragments. The model results have been verified with the subsidence and stress data recently collected from a longwall mine in the eastern United States. INTRODUCTION In 2015, there were 40 longwall mines operating in the United States, each producing an average of 4.5 million tons of coal per year, and they supplied 60% of the U.S. underground coal production. This represents a substantial increase from 50% three years earlier (Sears, Tulu, and Esterhuizen, 2017). During this period, reportable roof fall rates in U.S. longwall mines also increased. Large roof falls that can block the gateroads are not only a ground-fall hazard, they can disrupt the ventilation system, block the escapeways, and increase the potential for elevated methane levels in the gob. To address these hazards, the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) is conducting research to improve the design of ground control systems in longwall gateroads. Gateroad stability is primarily determined by the longwall pillar design. Generally, the required dimensions of the pillars around a longwall panel are determined first, which then dictates the location of the gate entries relative to the mined panel. The Analysis of Longwall Pillar Stability (ALPS) method is the most accepted gateroad pillar design procedure in the United States (Mark, 1992). The ALPS method accounts for local roof geology in the gateroad stability assessment by including the Coal Mine Roof Rating as an input parameter (Mark, 1992). The key assumption in the ALPS method is that unstable pillars result in unstable gate entries. However, experience provides examples of mines where pillar stability and gateroad stability are only loosely correlated (Su, Draskovich, and Thomas, 2003)."

Jan 1, 2017

By Brent A. Slaker, Khaled M. Mohamed

"Understanding coal mine rib behavior is important for inferring pillar loading conditions as well as ensuring the safety of miners who are regularly exposed to ribs. Due to the variability in the geometry of underground openings and ground behavior, point measurements often fail to capture the true movement of mine workings. Photogrammetry is a potentially fast, cheap, and precise supplemental measurement tool in comparison to extensometers, tape measures, or laser range meters, but its application in underground coal has been limited. The practical use of photogrammetry was tested at the Safety Research Coal Mine, National Institute for Occupational Safety and Health (NIOSH). A commercially available, Digital Single-Lens Reflex (DSLR) camera was used to perform the photogrammetric surveys for the experiment. Several experiments were performed using different lighting conditions, distances to subject, camera settings, and photograph overlaps, with results summarized as follows: The lighting method was found to be insignificant if the scene was appropriately illuminated. It was found that the distance to the subject has a minimal impact on result accuracy, and that camera settings have a significant impact on the photogrammetric quality of images. An increasing photograph resolution was preferable when measuring plane orientations; otherwise a high point cloud density would likely be excessive. Focal Ratio (F-stop) changes affect the depth of field and image quality in situations where multiple angles are necessary to survey cleat orientations. Photograph overlap is very important to proper three-dimensional reconstruction, and at least 60% overlap between photograph pairs is ideal to avoid unnecessary post-processing. The suggestions and guidelines proposed are designed to increase the quality of photogrammetry inputs and outputs as well as minimize processing time, and serve as a starting point for an underground coal photogrammetry study.INTRODUCTIONThe stability of underground mine ribs has been a safety concern for underground coal mines for decades. Unfortunately, the average rib fatality rate has been about 1.3 per year between 1996 and 2013 (Jones et al., 2014). In an effort to better understand coal rib behavior, photogrammetry is being investigated in this study as a measurement tool for surveying ribs in an underground coal mine environment."

Jan 1, 2016

By Keith Heasley

This paper is a retrospective on the development, application, and enhancement of the LaModel program from a personal perspective. The narrative starts with an explanation of the objectives behind the original development of the program and then introduces some of the unique and very practical features of the program. Next, a demonstration of how LaModel was advantageously used to model stresses and displacements in a multiple-seam mining situation with highly variable topography is presented. This is followed by the details of a number of the major enhancements and expansions of the program over the years. A back-analysis of the Crandall Canyon Mine collapse is then briefly presented, along with the associated development of a recommended calibration procedure for the critical input parameters to LaModel. Finally, some of the present research areas are briefly described, and future enhancements are introduced.

Jan 1, 2011

By Takashi Sasaoka, Hiroshi Takamoto, Kikuo Matsui, Hideki Shimada

"Indonesia is the second largest coal exporter to Japan. Almost all the coal is produced from open cut mines. However, a great deal of coal is left in the highwalls of the mined-out pits. The use of highwall mining systems has increasingly come into play in the U.S. and Australia, when overburden depth exceeds economical recovery in an open cut mine. However, the stability of the highwalls is always a major safety concern in such mining. This paper describes the characteristics of the highwall mining system and discusses the appropriate highwall mining system for use in Indonesia.INTRODUCTIONIndonesia produces over 200 Mt of clean coal and is the second largest coal exporter to Japan, accounting for about 32 Mt of coal annually. Over 99% of the coal produced in Indonesia comes from surface mines. More open cut mines will be developed and more coal will be mined in order to fill the great demand both in Indonesia and the rest of the world.In open cut mines in Indonesia, there are many sites where mining operations have developed long highwalls that have been abandoned due to the current economics. Mining operations have been transferred to lower stripping ratio blocks of coal or overlying seams. In some cases, coal lies buried beneath spoil heaps or is covered with mud and water. It is estimated that there is a great deal of coal beneath abandoned and working highwalls. Considering these situations, it seems to be worth introducing highwall mining systems into Indonesian open cut mines.Final highwalls of open cut mines can form the starting point for other mining methods, such as highwall or underground mining. In its basic application, highwall mining is a technique utilized after an open cut portion of a reserve has been mined, sometimes prior to the introduction of underground mining (Seib, 1993). In this system, the coal seam is mined by remotely operated equipment, such as an auger machine or a modified continuous miner incorporated into a highwall mining system. The major problems with highwall mining systems are less coal recovery due to leaving coal as the pillars and the instability of openings and highwalls due to the pillar and roof failures."

Jan 1, 2010

By David Bigby, Tim Ross, David Conover

"Extensive arrays of telltale roof monitoring instruments were recently installed in a Mexican copper mine and a large underground mined storage facility in the eastern U.S. The data were used to evaluate roof stability during development and retreat mining and after installation of supplemental supports. Both manual-reading and automated systems were employed and consisted of up to 64 instruments. This paper will discuss the practical issues involved with installation and monitoring, including reliability and maintenance. Examples will be given for telltale response in relation to known events affecting roof stability, including nearby pillar extraction roof caving, installation of supplemental cable bolts, and separation of the immediate roof layer. The strategy for processing the large quantity of data, presenting the data for review, monitoring the system remotely, and identifying and reporting critical events will be described.INTRODUCTIONTelltales have been used for many years with many varied applications. They are relatively inexpensive, easy to install and interpret, robust, and adaptable. The term ""telltale"" generally denotes a strata extensometer that incorporates a visual indication (and warning) of strata movement. The most common dual-height telltale (Figure 1) was developed by British Coal in the early 1990s as roof bolting was replacing steel arch support (Bigby, 2001). Dual-height telltales provide immediately visible measurements, distinguish between movements above and below the bolted height, and are an established means for providing preemptive warnings of roof falls.Many improvements and modifications on the basic design have been developed to adapt to different mining conditions. For example, triple-height telltales are commonly used where roof bolts of different lengths are installed. The standard manuallyread telltales are limited by the difficulty of obtaining frequent, consistent, and accurate readings, especially in high openings. The instruments may also be located in unstable or inaccessible areas. Consequently, an intrinsically safe electronic telltale system was developed that combines high accuracy and both local and remote reading options. The system supports a network of up to 100 dualheight telltales on each of four separate branches. The instruments are connected with a two-conductor cable and can be read both underground, using a portable readout, and on a surface computer (Figure 2). The automated system still provides the visual warning indication underground."

Jan 1, 2010

Large-scale shear apparatus is designed to investigate the shear hehaviour of simulated soft rock joints under constant normal stifmess condition. Regular saw-teeth profiles having inclinations between 9.5" and 26.5" have been tested. The strength envelope based on these test results indicates that predictions made by Panon (1966) are accurate for the lower asperity angles. However, for higher asperity angles, Patton's model overestimates the shear strength especially in the low to medium normal stress range. In contrast, while Barton's model (1973) is realistic for Constant Normal Load (CNL) condition, it seems to be inappropriate for modelling the shear behaviour of soft joints under Constant Normal Stiffness (CNS) condition. An empirical strength envelope for the prediction of peak shear strength of joints is proposed in this study to account for the change in normal stress and surface degradation during CNS shearing.

Jan 1, 1997

By J. B. Lizak

This paper is not available for inclusion in the Proceedings at the time of printing, but it will be included as an insert.

Jan 1, 1984

By Chris Kelly

The Monroe County Quarry is an open pit granite quarry located near the town of Bolingbroke. Monroe County. Georgia. The quarry has been in continuous operation for approximately 10 years. The quarry covers approximately 27 acres and has an annual production rate of 1.0 million tons. On the morning of April 26. 2000 a sudden rapid highwall failure occurred at the west end of the north wall of the quarry pit. The failure occurred approximately one hour after a three inch-wide crack was observed in an access road located at the crest of the highwall. No indications of failure had been observed prior to the development of the crack. The active mining area had been at the base of the failed area. The pit was successfully evacuated prior to the failure and there were no losses of either personnel or equipment. The amount of failed material was estimated to be in excess of two million tons. In order to ensure a safe working environment at the quarry a slope monitoring program was established in the area of the failure. The program consisted of using an EDM survey instrument to periodically measure the location of survey prisms installed at carious points on the north wall. The locations of the prisms were recorded over several months and changes in location were analyzed in order to identify and characterize the movement of the failed mass. The results of the analysis provided a basis for recommendations regarding access to various areas of the quarry. This paper discusses the factors contributing to the failure, the method of post-failure slope monitoring, anti the interpretation of the monitoring data.

Jan 1, 2002

By Enguang Zhu, Kangning Zhang, Yang Li

"Due to the use of outdated mining technology or room and pillar mining process in small coal mines, the coal recovery ratio is only 10% - 25%. In many regions of China: the damage area caused by the small coal mines amounted to nearly one hundred square kilometers. Therefore, special mining techniques must be taken to reclaim the wasted resource in disturbed coal areas. This paper focuses on the different mining methods by analyzing the longwall panel layout and abandoned gateroad (AG) distribution in in the abandoned area of Cui Jiazhai Coal Mine in northwestern China. On the basis of three-dimensional geological model, FLAC- 3D numerical simulation was employed. The abutment pressure distribution was simulated when the panel face passed through the disturbed areas. The proper angle of the inclined face was analyzed when the panel face passed through the abandoned gateroads. The results show that the head end of the face should be 13-20m ahead of the tail end. The pillars on both sides of abandoned gateroads had not been damaged at the same time, and no large-area stress concentration occurred above the main roof. Therefore, the coal reserves of disturbed areas can be successfully recovered by using underground longwall mining. INTRODUCTIONDuring the 70-90's, there were a lot of small coal mines in China. Due to their disordered mining, most of the small coal mines left a great many abandoned gateroads (defined as AG in this paper) and a large area of damage coal seam. In these type of coalfields, there exist many mining risk issues, including nonuniform stress in the overburden, flooding and hazardous gases accumulated in the gob. So how to lay out a longwall panel and successfully mining under this type of abandoned small mines is a big issue nowadays in China.As mentioned above, longwall panel is being performed in the damaged coal seams in order to increase recovery of coal reserves (Wang, 2009). However, the abandoned geteroads intersect to each other all around the area. So a series of production issues arose while the panel face is passing through these AG. Gang and Gong (2015) analyzed the roof stability and abutment pressure distribution during the face was passing those AG that were parallel and inclined to the faceline. Xie, et al. (2015) proposed the ground control mechanism by passing the AG in top-coal caving longwall mining. He recommended to stop the face advance until the roof is over, using high strength bolts and cable bolts, and grouting consolidation. This paper studies the different mining methods by analyzing the longwall panel layout and AG distribution in damage coal seams. Theoretical analysis and field observation were conducted to determine the overburden movement when the face was advancing under the AG. The pillar between face and parallel AG changes from elastic to plastic and eventually to the residual supporting status. All these three status was combined with the roof structure to establish the theoretical model to calculate the shield support capacity. Numerical modeling was employed to simulate the pillar stability and determine the abutment pressure distribution as the face inclined to the AG during longwall mining."

Jan 1, 2016

By John A. Rusnak

"This paper discusses the variation of coal strength based on the megascopic coal lithotypes for Central Appalachian high-volatile A coal beds. The composition of coal beds is complex and variable, depending on the depositional environment associated with original plant material, inflow of clastic material, and water level fluctuations in the original swamp/mire environment. Thus, different types of coal and sediment are formed within each coal bed. These differences in coal composition were first classified by Marie Stopes, a paleobotanist, in 1919. The classic coal megascopic lithotypes are vitrain, clarain, and durain, which correspond to bright, bright banded, and dull coal, respectively. Stopes also identified that the lithotype fusain, which is mineral charcoal, has no inherent strength and can act as a plane of discontinuity. In this study, two other coal-bed lithologies are also considered—bone and carbonaceous shale. This makes for a comprehensive suite of coal-bed stratigraphic components apart from rock partings. A total of 1,000 uniaxial compressive strength (UCS) and 440 indirect tensile strength (ITS) tests were conducted on cores from southern West Virginia that were specifically logged and described using the megascopic coal lithotype nomenclature. Statistical analysis is presented showing the results for each lithotype group with mechanical properties correlated to the lithotype. Previous studies have analyzed the mechanical breakage properties associated with coal lithotypes, which correlate well with these results. However, coal rank does appear to be a contributing factor, and this study is confined to only high-volatile A bituminous rank. Application of these results would be well suited to a rock mass classification system to address coal pillar rib stability. This would allow for rib support design and implementation to consider relative coal strength by visual observation of the seam stratigraphy through ongoing observations within a mine. Changes in seam composition can be readily identified, allowing the adjustment in rib support design. Another application would be for the determination of numerical modeling inputs based on detailed seam stratigraphy. However, these results, even with the standard strength reduction criteria, may not be applicable to currently accepted empirical coal pillar design procedures."

Jan 1, 2017

By Jessica M. Wempen

Differential Interferometric Synthetic Aperture Radar (DInSAR), a satellite-based remote sensing technique, has been demonstrated as a potentially practical method for measuring mining induced surface subsidence. Unlike traditional methods of subsidence monitoring, DInSAR has the capacity to generate subsidence data on a regional mining scale with a relatively high data density. Using DInSAR to evaluate subsidence over large regions with relatively long time scales has the potential to help quantify the impact of subsidence in the mining region, and provide a means for validating whole-mine geotechnical models. In this study, nine pairs of interferometric data from the Japanese Advance Land Observing Satellite (ALOS) were processed using DInSAR to generate displacement maps for a group of trona mines in southwest Wyoming. The data cover a time span from December 2007 to March 2011. The maximum subsidence for one of the mines totaled 1.3 meters for this period. Cumulative DInSAR displacement maps show the development of subsidence over time. In this mining region, surface subsidence is generated primarily by extraction of trona using retreating longwalls. Additionally, trona is extracted by solution mining, which also generates measurable surface subsidence.

Jan 1, 2014

By Shengliyang Yang, Jinghu Yang, Jiachen Wang, Xiaomeng Li

"Safe and efficient mining of extremely inclined thick coal seams less than 20m thick is one of the new challenges in China coal industry. In recent years, the extremely inclined thick coal seams have been encountered in some old mines and western China, and currently the top coal caving longwall mining method has been successfully applied to this kind of coal seams. Accordingly, this paper studies the roof movement and its impact on shield supports of top-coal caving longwall mining in extremely inclined thick coal seams. The structure of main roof before failure was simulated by the fix-ended beam, and provided the solutions for determination of maximum compressive stress of the bottom beam end and maximum tensile stress of the top beam end. The failure mode on the upper end of working face is mainly a combination of compression and shearing, while that for the bottom end is tension and shearing. Roof fracture begins at the upper end of working and propagates downward. The shape of collapsed roof strata can be described as parabolic and divided into three segments from top to bottom, including no filling, uneven filling and densely filling segments. The roof loading conditions of no filling segment is more likely to have dynamic burst impacts.INTRODUCTIONExtremely inclined thick coal seam refers to that the dip angle of coal seam is greater than 45° and the thickness is greater than 3.5m (Wang and Zhang, 2015a; Wang and Zhang, 2015b; Wang, 2005; Xie, Gao, and Shangguan, 2005; Wu, et al., 2014; Deng and Wang, 2014; He, et al., 2015). This type of coal seams can be divided into three categories: 1. The extremely inclined thick coal seam, of which the thickness is less than 5m and the dip angle is less than 60°, is usually mined by fully-mechanized longwall mining method. 2. The extremely inclined thick coal seam, of which the thickness is 5 m-20m, is usually mined by top coal caving longwall method. And 3. When the thickness of extremely inclined thick coal seam is greater than 20m, it is mined by the horizontal section top coal caving longwall method. For example, the average angle ofWudong coal mine in Xinjiang province is 45°, and the thickness is 27m. Wudong coal mine is applying the horizontal section top coal caving longwall mining, producing 3 million tons annually per working face (Figure 1)."

Jan 1, 2016

By Mark G. Colwell, Russell Frith

"An Analytical Model for Coal Mine Roof Reinforcement (AMCMRR) has been developed. AMCMRR utilizes a Factor of Safety (FOS) approach, which is commonly used in all forms of engineering. The starting point in the development of AMCMRR was an existing analytical roof behavior and roof support design methodology/model, originally developed by Colwell. This technique was used successfully in the Australian underground coal industry for roof support evaluation and design prior to and during the course of the research project, and when used, it was essentially calibrated on a site by site basis.It has long been recognized that bolts and longer tendons can modify the behavior and load bearing capacity of the reinforced roof via the concept of beam building. The break-through in developing AMCMRR was combining the original analytical model with a comprehensive database (associated with Australian collieries) to effectively quantify this reinforcing effect, and this in turn provided the ""platform"" by which this analytical model can be calibrated for the entire Australian underground coal industry.This paper focuses on the application and use of AMCMRR and the analyses undertaken to quantify the reinforcement beam building offers to the immediate roof. Furthermore, this paper demonstrates that a combined empirical and analytical approach is currently the most practical way of developing credible geotechnical design tools for the Australian or any other underground coal industry.BACKGROUNDBy the start of 2006 the ALTS (Analysis of Longwall Tailgate Serviceability-Colwell et al., 2003) and ADRS (Analysis and Design of Rib Support-Colwell, 2006) design methodologies were being routinely and widely used within the Australian underground coal industry. As a result of their success, Colwell Geotechnical Services commenced a research project entitled, ""The Future Development and Integration of ALTS & ADRS for Improved Underground Roadway Design. "" The project (which became known as the ALTS 2006 Project) was funded directly by several of the major coal producers as well as individual Australian collieries."

Jan 1, 2010

By Muhammad Zaka Emad, Rangzeb Goraya, Muhammad Usman Khan

"Numerical modeling has been used extensively to assess the stability of surface and underground mines. Tabular, steeply dipping ore bodies are generally mined out by open stoping methods with delayed backfill. Cemented rockfill (CRF) is employed as a backfill material for narrow vein deposits with low production rates. Sublevel stoping methods with delayed backfill are employed to mine out steeply dipping ore bodies. Backfill is exposed to blast-induced vibrations and dynamic loading due to loss of confinement, which could lead to backfill failures. Backfill failures could influence the operating cost of a mining stope and the productivity of the entire mining project. This work shows a detailed overview of the factors contributing to backfill failure. A detailed literature review is presented along with case studies of longhole stoping operations from the Canadian Shield region for this work. The backfilled stopes are analyzed with the finite difference code FLAC3D. The literature review shows that the factors primarily responsible for fill failure are the strength of backfill, stope geometry, mining sequence, and blast-induced vibrations. INTRODUCTION Sublevel stoping methods with delayed backfill are popular in Canadian hardrock and metal mines. Backfill facilitates ground control and greater recovery of ore with pillar mining. It reduces wall slough, thus decreasing ore dilution from adjacent walls. The production of cemented rockfill (CRF) is simple; rock aggregates are mixed together with cement slurry and then placed in a mined-out stope. CRF has a low water content, thus it requires no additional drainage unlike some other backfill. Low water-to-cement ratio enables faster curing rate, hence a faster mining cycle can be achieved (Annor, 1999; Hassani and Archibald, 1998; McKay and Duke, 1989). CRF is generally placed in stopes from the upper sill drift using a truck or a load haul dump machine. Some of the problems associated with CRF are the moderate to high operational cost, the difficulty to get a tight filling, and segregation. Backfill failure is a product of many factors, such as cementation, particle size distribution, placement method employed, water quality, segregation, and blast-induced vibrations. The problem of segregation in aggregates has been observed when aggregate is dumped from a backfill raise (Meech, 2012; Indiana DOT, 2013). Segregation becomes unavoidable when the aggregates are not properly sized (Yu and Counter, 1983; Stone, 2007; Yu, 1989). The exposed backfill zones will contribute to ore dilution due to backfill when subjected to dynamic loading due to fill failures. This paper presents a detailed literature review and numerical modeling results of a mine backfill, along with case studies from longhole stoping operations. The backfilled stopes are analyzed with the finite difference code FLAC3D (Itasca, 2017). The literature review shows that the primary factors responsible for fill failure are the strength of backfill, geometry of stope, sequence of mining, and the vibrations induced by blasting operations."

Jan 1, 2017

By Nicholas Chlumecky

One of the most dangerous jobs in mining is that of resupporting the roof after a fall has occurred. The resulting cavity may be more than 30 feet high, with relatively unstable sides and roof. It is often impossible to proceed with rehabilitation without exposing men and equipment to unsupported rock. Temporary supports provide margin- ally effective protection because of the lack of available footing. Furthermore, the usual supports in rehabilitated fall locations are not permanent, require frequent maintenance, and fail to eliminate some remaining serious safety hazards. This is typically the case for high cavities where loose rock drops from considerable heights from between roof bolts. Supports made of cribbing, beams and additional cribbing to the high points of the fall in many cases do not provide good protection due to the deterioration and shrinkage of timber. In mines, high cribbing frequently loses contact with the roof and thus provides no protection against rocks peeling off the sides. This is true in spite of the fact that at time of installation the cribbing was wedged tightly to the roof. Therefore, when considering the difficulties which occur with current practices, the objective is to find alternate methods of resupporting the high roof after a fall.

Jan 1, 1981

By Jessica M. Wempen, William G. Pariseau, Michael K. McCarter

"Quantitative analysis of mine-wide subsidence at the kilometer scale and details of stress distribution about an advancing longwall face are estimated using an adaptation of the finite element method. The method is well suited to the tasks at hand. For greater realism, variability of strata properties is taken into account as are the effects of joints and cleats on elastic moduli and strengths. Evolution of pillar stress and entry closure remote from the face is readily quantified in a series of analyses that simulate face advance. Computed results compare favorably with the evolution of closure measurements about an instrumented pillar in a two-entry headgate. The appropriateness of the finite element method is confirmed. This method is based on first principles that avoid empirical schemes of uncertain applicability and numerical models “calibrated” by fitting computer output to mine measurements.INTRODUCTIONMine-induced seismicity is intimately related to strata mechanics associated with longwall coal mining and room and pillar mining, as well. Strata deformed beyond an elastic limit often tend to fail rapidly by brittle fracture and, thus, to emit acoustic signals in the form of elastic waves. Understanding the induced seismicity in coal mining offers the potential for early warning of hazardous conditions. Many years of experience with seismic phenomena associated with hardrock mining suggest considerable complexity should be expected. However, recent coal mine studies (Pariseau, 2014; Pariseau, 2015; Pariseau and McCarter, 2015; Pariseau and McCarter, 2016) have shown high correlations of seismicity with element failures in finite element simulations. The main lesson learned from these studies is one elaborated by Iannacchione et al (2005); deviation from normal activity is an early warning of ground control difficulty. For example, an abrupt increase in seismic event rate, or equivalently, an increase in element failure in finite element simulation of panel advance, is a cautionary indication for ground control. Present and past study results demonstrate the effectiveness of finite element simulations for mine design and early detection of potential ground control issues."

Jan 1, 2018