Search Documents

By Gabriel S. Esterhuizen

This paper addresses the need for a method to compare the effectiveness of different support systems when designing ground support in coal mines. At present, support design methods include empirical methods based on observations of past performance of installed support systems, analytical methods where the roof is typically simulated by elastic beams and numerical model analysis. The approach presented in this paper estimates the relative stability of a support design through geotechnical evaluation of the rock mass and numerical model analysis of the interaction between the rock mass and the support system. Models are used first to simulate the design performance at the expected rock conditions. The rock strength is then reduced until collapse is indicated in the model. The stability factor is then calculated as the ratio of the expected rock mass strength to the rock mass strength at the onset of collapse, and is similar to the well-known factor of safety used in engineering practice. The stability factor can be used to assist in developing a final support design by comparing the effectiveness of various support systems and the stability of excavations under various geological and loading conditions. Examples of the method?s application in three different geological settings are presented.

Jan 1, 2012

By Changsheng Song

With increasing depth of coal mining in China, the number of coal and gas outbursts has been increasing for years. By means of destressing the protective seam, the gas in the protected seam is drained to reduce gas concentration in the high gassy seams, thus ultimately attaining simultaneous extraction of coal and gas. Base on the simulated material scale modeling and numerical simulation, the protective seam mining method was practiced at No. 8 coal mine in Pingdingshan city. After extracting the No. 15 seam, the overlying strata movement and the deformation of No. 9-10 protected seam were studied. The experiments showed that it was feasible to destress the protected seams with large interburden thickness. As the protective seam was being mined, the protected seam experienced dynamic movement process and the change in vertical stress in the No. 9-10 seam assumed ?W? shape. When the face had advanced 656 ft (200m) from the setup room, the No. 9-10 seam was fully destressed, resulting in easy gas drainage in the destressed zone. Recommendations on mining sequence of multiple seams mining in the Pingdingshan coal areas were made.

Jan 1, 2008

By Holger Witthaus

Beside the traditional geomechanical evaluation methods the geotechnical parameters are recognized as important facts of the planning work for multiple seam mining. Standards for applied monitoring and investigation methods for geotechnical determination of drill cores, laboratory rock-tests and observation of roadheadings are the basics for rock mechanics classification and support design. The geomechanical classification is in this context an essential element. The planning procedure, as it is becoming more and more detailed, beginning with the panel layout up to the technical instructions of roadway development and design of roadheading machinery, nowadays uses a lot of geotechnical information that also are expanding to include quantitative determination of more parameters. The current monitoring system includes the description of separation planes using drill cores and roadheading observation as well as laboratory tests of rock-strength and geophysical borehole examinations. This information is analyzed within the geomechanical standard-classification. The re-engineering process of comparison the predicted support success to the actual monitoring results provides the opportunity for continuous optimization of the planning work und support design. This way of empirical analysis is used for basic planning work in Germany for decades. But using the technical standard of information technology and a centralized database now it is possible to reach quick-win effects in implementing research results on the one hand and actual experiences on the other hand.

Jan 1, 2006

By John Feddock

A recent increase in energy demand has resulted in the rapid growth of coal consumption in the People?s Republic of China (PRC), which is the largest coal producer and consumer in the world. Reportedly, the safety issues in Chinese coal mines have been improving, but the number of fatalities and serious injuries continues to be alarmingly high. The number of fatalities from catastrophic accidents have prompted researchers to review the Chinese mine safety situation and to look for potential solutions. Marshall Miller & Associates, Inc. (MM&A), along with various collaborators, has investigated these issues as part of its work on various projects in the PRC and has discussed the concerns with relevant Chinese officials. Preliminary investigations by MM&A of coal mine accidents during 2001?2006 in the PRC indicate that 65%-78% of the total fatalities were the result of gas explosions and roof falls in underground mines. Even though the drainage of methane has been practiced for decades, current practices do not always produce satisfactory results due to technical constraints and equipment limitations. Based on prior experience of in-seam degasification at the Daning Coal Mine located in Shanxi province, MM&A believes that in-seam directional drilling technology can be a viable solution to degas the low-permeability Chinese coal deposits. This paper 1) reviews current Chinese coal mine safety conditions, 2) analyzes the advantages/disadvantages of current degasification practices in China, and 3) presents the pre-mining degasification practices for the longwall panel at the Daning Coal Mine.

Jan 1, 2007

By Axel Preusse

Mining subsidence plays an increasing important role in the Chinese hard coal mining. Reasons for this are a substantial rise of production during the last decade, a dense settlement in many mining regions, the increasing emergence of private residential property as well as a grown environmental awareness. German companies and research institutions hold an over more than 150 years existing know-how in all subjects of mining subsidence engineering. Due to partially comparable preconditions regarding mining depth, mining methods and geological conditions, a close co-operation between German and Chinese mining subsidence engineering experts has been in existence for some years. This German-chinese co-operation is introduced in this paper.

Jan 1, 2007

By Sudhir Kumar Kashyap

In underground activities ground control is a challenging problem. It affects safety, production, and efficiency. As per statistics of accident data, ?fall of roof/sides? is one of the major causes of mine accidents. In many cases, our experiences and understanding of soil and rock behavior still fall short of being able to predict how the ground will behave. Presently, empirical approaches to design are widely used in estimating mine support parameters. Under these circumstances, expert judgment plays an important role, and such accidents can be obviated with accurate measurement and optimization of data and analysis using the neuro-fuzzy technique of artificial intelligence. Recently, a neuro-fuzzy hybrid approach has become one of the major areas of interest in engineering fields because it gets the benefits of neural networks as well as those of fuzzy logic systems, and it removes the individual disadvantages by combining them on the common features. Neural network and fuzzy logic technologies have common features, such as a distributed representation of knowledge, the ability to handle data with uncertainty and imprecision, etc., like in ground control. Fuzzy logic technique has tolerance for imprecision of data, while neural networks have tolerance for noisy data. In this paper we have focused an intelligent technique, i.e., neuro-fuzzy technique, to approximate the setting load given to the standing support (props) erected for the purpose of supporting freshly exposed roof during underground mining. We have used twelve input variables of rock parameters, and after having trained using a neural network with a sigmoidal function as an activation function, simulation was done to find the output parameter, i.e., the pre-load (setting load)to be applied on props. Outputs of the neural network were again fed to the fuzzy system together with the twelve parameters, incorporating five triangular membership functions for each parameter. Final optimum output was approximated using the MATLAB program, which was found to be satisfactory. Neuro-fuzzy technique has better performance over individual neural networks or fuzzy logic technique.

Jan 1, 2012

By John Hoelle

Coal mines in southern West Virginia, south-western Virginia and eastern Kentucky have experienced coal bumps at least since 1933. Most of the bumps have occurred due to high cover, strong roof and floor strata and stress concentrations due to the mining sequence. A longwall mine in eastern Kentucky first experienced coal bumps on the tailgate side of the longwall face in 1989. The bumps continued until 1996. The bumps were the result of: Thick overburden up to 2200 feet Strong roof and floor (strata strengths up to 25,600 psi UCS and elasticity modulus up to 4,800,000 psi Previous over-mining in places Sandstone channels Not all characteristics occurred simultaneously. The bumps produced seismic events recorded up to 4.3 (Richter scale magnitude), and damaged pillars that were up to 147 by 152 feet in size.

Jan 1, 2008

By Tex M. Kubacki

In 2007, the University of Utah Seismograph Stations (UUSS) temporarily expanded its seismic monitoring network in Emery County, Utah, in response to the August 6 Crandall Canyon mine collapse that trapped six workers. In spite of this additional coverage, no seismic events were located in the area during a six-day period (gap) from August 8 to August 13. The Mine Safety and Health Administration (MSHA) ?Command Center Log Books? however, contain references to 16 instances of underground ?bumping? and ?bouncing? that occurred during the gap. When ground truth information provided by the log books is compared to the raw seismic data recorded by the UUSS network, the correlation offers insight into the chronology of mininginduced seismicity (MIS) in the aftermath of the collapse. The new research focuses on identifying and locating seismic events that occurred during the six-day gap using double-difference relocation techniques and correlating them with log book ground truth. Ten seismic events were identified in the vicinity of the mine during the six-day gap, ranging in magnitude from coda magnitude (MC) 0.5 to 1.4. Three of these events were amenable to location by double-difference techniques. The location of one of these events is directly confirmed by ground truth information from the log books. As a result of this new research, the accuracy of Crandall Canyon double-difference locations has been improved, and the number of events correlated with ground truth information has increased. The seismic events occurring in and around the collapsed area appear in two distinct sections of the mine?east and west of the center of collapse. It was originally reported that the post-collapse events occurred in episodic clusters. The first two episodes occurred to the east, followed in time by a cluster on the west, and then by a third episode on the east. With the addition of new events to the data set, this pattern is no longer as clear, although the events still occur in clusters. Only one MIS cluster was found to occur within the bounds of the minimum estimated collapse area (Pechmann et al., 2008).

Jan 1, 2012

By Murali M. Gadde

Welded wire mesh is the most commonly used skin control technique in the United States underground coal mines. Currently, selection of the mesh is based on trial and error rather than any rigorous design methodology. Several factors affect a wire mesh?s performance including the amount of rock material to be supported and how the load is distributed, wire gauge, aperture size, grade of steel, weld strength, bolting pattern and sheet size. Although the best way to choose the mesh is to conduct full-scale physical load tests, because of the limitations on the number of variables that can be considered in such tests and the requirement of an elaborate test set-up, it may not always be possible to use this option. An alternative would be to use numerical modeling to study the load-deformation behavior of a wire mesh. In addition to providing a very detailed stress, strain distribution in the entire mesh, the advantage of this approach is the ease with which parametric studies can be conducted. In this paper it is shown that the load-deformation curves generated by nonlinear numerical models match closely with laboratory derived ones. Then, based on parametric studies, design guidelines are developed to choose the mesh appropriate for different loading conditions. The modeling studies also bring forth the limitations of the current lab studies. For example, under some conditions it was noticed that the small sheet size considered in lab tests would produce higher mesh deformations than a full-size one used in actual practice.

Jan 1, 2006

By Stephen C. Tadolini

The International Ground Control Conference in Mining has always provided an open forum for the publication, presentation, discussion, and often heated debate on roof bolting systems mostly with attention to how, when, and why they work. During the last 24 Conferences at least 170 papers have been presented by International Experts on these ?simple? devices that range in length from 30-inches to 20 ft and from 5/8 to 2 inches in diameter. Roof bolts are primarily mechanically anchored, glued, cemented, or driven. Bolts are placed vertically, angled, or tied together with special fixtures (trusses and slings). They have been termed active, passive, stick-slip, and several other descriptive acronyms or mining slang expressions. This retrospective paper will present the changes in bolt types and usage, point out some of the biggest myths and hail the most significant advances (according to the authors? opinions of course).

Jan 1, 2006

By Paul Singh

Blasting is an integral part of mining activity and is an inherently destructive process. The quality of the rock mass in which an excavation is being driven has a strong influence on the level of dynamic forces to which the rock can be subjected and sustain damage. Though each specific rock mass occurrence is unique, yet there are common rock mass features which influence the outcome of controlled blasting in a similar way. A field study was conducted which involved assessment of blast damage at several operating mines and blasting of small scale models. The effects of block size and strength, joint parameters, ground water, weathering of rocks and rock mass rating on the results of controlled blasting have been investigated and discussed in this study. The influence of number and thickness of weak layers on overbreak control has been discussed in the light of practical data. Critical particle velocity ranges for damage to rock masses with different qualities have been outlined. An approach for the judicious design of perimeter hole pattern and charge concentration has been proposed.

Jan 1, 2007

By Rob Thomas

Main gate roof control during longwall retreat is subject to a significant increase in horizontal stress and risk. The implementation and management of an appropriate roof support design is as a result, an imperative requirement for any longwall mine and must in addition to the likely consequences of a roof fall, also consider the variables of the geotechnical environment, associated support costs and practicalities. This paper will therefore summarise a number of recent advances in main gate roof control in the Australian coal industry. Points considered include; (i) the ?Longwall Acceleration? concept, (ii) macro-scale horizontal stress notching, (iii) micro-scale horizontal stress notching, (iv) bedded versus laminated roof types and (v) the type of cable reinforcement used.

Jan 1, 2006

By Kieran Black

The immediate roof lithology at United Colliery is extremely variable and provides a challenge for the design of secondary support. Support design in recent longwall installation roads at the mine has been carried out using strata management techniques. These techniques allow a robust yet economical secondary roof support design to be achieved. Analysis of roof lithology and roof displacement during first pass driveage are used as a basis for the optimisation of the secondary support design prior to roadway widening. This paper will demonstrate the application of practical strata management techniques in the optimisation of secondary roof support in six installation roadways at United Colliery. The experience gained from the installation roadways for LWs 1 to 5 will be briefy discussed. The experience from LW 6 will be discussed in greater detail. The paper will describe the strata management system that was used, including mapping, borescoping and extensometry, as well as the development and application of a Trigger Action Response Plan (TARP).

Jan 1, 2007

By John E. Feddock

Retreat mining plays an important role in the coal production within Kentucky and the Appalachian Coal Basin. In Kentucky, the majority of retreat mining is performed in the Eastern coal field. However, since September 2004, Kentucky has suffered four mining fatalities during retreat mining operations, and the coal industry has focused attention on the safety concerns associated with retreat mining practices. The Kentucky Department of Natural Resources (KYDNR) engaged Marshall Miller & Associates, Inc. (MM&A) to conduct a study to ensure that retreat mining is utilizing the best technology currently available and that the current available employee training programs afford maximum safety to miners. MM&A studied 34 coal mines that were conducting active retreat mining operations and represent about one third of all the mines with approved retreat mining plans in Kentucky. This paper summarizes the major research work conducted (Feddock and Ma, 2006) and recommends the practical methods for improving safety during retreat mining operations.

Jan 1, 2006

By Jun Han

Coal has been mined in the Kailuan mining area for more than 130 years. The remaining reserves consist of, in large part, coals that would have been considered economically unminable or technically not feasible by the previous generations. Some of the current operations have to resort to overmining because the lower seams had been extracted in the past. This paper deals with the feasibility and proper layout of mining roadways of overmining carried out in the No. 5 seam of Qianjiaying coal mine of Kailuan mining area using numerical and physical simulation. FLAC2D was used to investigate the characteristics of stress and displacement in the overburden after extraction of the lower seams. It also analyzed the proper layouts of gateroads in the upper seams, i.e. locating them in the stress-relief zone of the gob so that their stability can be easily maintained. In addition, a two-dimensional physical model was constructed for investigation of damages to the upper seams due to mining of the lower seams. Finally, based on the results of investigations, proper gateroads layout was designed and successful extraction was implemented for panel 1357 in the No.5 seam.

Jan 1, 2009

By Wenquan Zhang

Based on the mining and geological conditions of Wadong Mine, Longkou City, Shandong Province, China, a viscoelastic model with proper creep parameters was established. The 3-D ANSYS was used to simulate surface subsidence, analyze overburden subsidence characteristics, and propose the rational mining and pillar widths for mining in weak rocks and under special mining conditions, and provide the policy makers scientific data for decision making on mining activities.

Jan 1, 2006

By Yi Luo

The efforts to mitigate longwall subsidence influences on various residential and farming structures by many coal mining companies have been successful in the recent years (Luo, et al, 2003). The successes were largely dependent on the accurate subsidence predictions, correct assessments of potential influences, appropriate design and implementation of the mitigation measures. However, such efforts for protecting large industrial structures are still very rare. In this paper, the successful assessment and mitigation of the subsidence influences associated with a very intensive dynamic longwall subsidence process on a large workshop are presented.

Jan 1, 2005

By John Latilla

Exxaro Mining?s Matla Coal situated in Mpumalanga, South Africa operates two shortwall faces on the No 4 and No 2 seam while the No 5 seam has also been longwalled in the past. Severe strata loading events have lead to a number of serious roof falls on the wall face (facebreaks) resulting in safety threats as well as considerable production losses. In 2002 the No 4 seam shortwall suffered a facebreak restricted mainly to the tailgate side of the mining panel due to a thick, near surface dolerite sill not breaking properly. This was partly due to the premature suspension of longwalling in the overlying No 5 seam. The resultant overloading lead to severe pillar damage and subsequent bord collapse. Surface pre-split blasting was successfully used to relieve the pressure as well as to pre-condition the dolerite above the following two panels. The shortwall on the No 2 seam has experienced mid-face loading due to No 4 seam chain pillars lying over this area and creating a secondary cantilever effect. Pre-split blasting of the solid rock above the No 4 seam pillars has resulted in a significant reduction in the number of facebreaks. The panel layout of the No 2 seam was subsequently changed so that the chain pillars on both the No 4 and No 2 seam are superimposed whereas previously they were offset.

Jan 1, 2007

By Francis S. Kendorski

Over the past 25 years, the present author has written with several co-authors a series of papers beginning with the landmark paper in the 1st International Conference on Ground Control in Mining in 1981, in turn, based upon U. S. Bureau of Mines (USBM) funded contract research managed by the author with a final report issued in 1979, all concerning this paper?s title subject, Effect of Full-Extraction Underground Mining on Ground and Surface Waters. Initially the work was a summary of British, Russian, and Hungarian experience tailored to United States strata conditions, but has evolved into a consistent and well-documented model of the behavior of strata influenced by full-extraction underground mining such as longwall coal mining. The several strata zones recognized in these works, Surface Fracture Zone, Constrained or Aquiclude Zone, Dilated Zone, Fractured Zone, and Caved Zone, have been observed by several workers in the field. The concepts presented initially 25 years ago have been adopted, rightly or wrongly, by state regulators, ground and surface water researchers, and mining practitioners. The development and utility of these concepts and recent findings will be summarized.

Jan 1, 2006

By Anthony Iannacchione

A Major Hazard Risk Assessment (MHRA) was developed in Australia after a series of mine disasters in the 1990?s. A MHRA is used to help prevent major hazards, i.e. fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, from injuring miners. A MHRA is a structured process that identifies the characteristics of major hazards, assesses and ranks the risk they present, and evaluates engineering and administrative controls to mitigate them. These controls typically consists of a broad spectrum of prevention, monitoring, first response, and emergency response techniques and helps to move an operation from a reactive to a proactive approach towards safety. This paper documents a MHRA performed at an underground mine where strata instabilities and fire hazards may threaten the condition of its escapeways. The objective of this MHRA is to 1) identify what hazards could affect the egress through the mine?s escapeways, 2) determine what unwanted events pose the greatest threat for the mine, and 3) recommend a plan to prevent or recover from the potential disruption of egress through the escapeway. The plan provides information on the key existing controls that should be monitored and audited, and makes recommendation of new potential controls to further reduce related risks. By documenting the use of MHRA to this specific ground control issue, this paper provides a framework for others to judge the merits of this approach and to help design and perform these activities.

Jan 1, 2007