Search Documents

By D. Diggins

Experimental apparatus for the determination of powder wettability is described. The principle of the technique is based on the measurement of the equilibrium capillary pressure in a packed bed of particles. Both the macroscopic solid-solution-vapour contact angle, e, and the specific surface area, A(m2g-1), of the powder, can be obtained. Experiments on angular quartz particles have been performed. A wide range of situations have been covered: hydrophobic and hydrophobic particles wetted with water, a variety of organic liquids and solutions of surfactants. The results show that reliable and reproducible values for 0 and A for angular and relatively coarse powders can be obtained with the proposed equipment for advancing liquid fronts in the absence of soluble surfactants. In the latter case and for receding liquid fronts in general, only qualitative trends have been obtained.

Jan 1, 1992

By Mehmet Guney

[The Atlantis-II-Deep is a hydrothermal mineralization located along the median valley of the Red Sea at a water depth of about 2200 m. Extensive exploration of the metal-rich brine deep revealed a potentially mineable deposit on economic interest consisting of oxides, silicates and sulphides with considerable concentrations of zinc, copper, cadmium and silver. Geostatistics was applied to assess the most likely in-situ vague of the metal potential for economical exploitation. Semi-variograms were constructed to characterize the structure of the regionalized distribution of the geological parameters. Volume grades and thicknesses were determined by the kriging technique, avoiding systematically biased high or low grades, and then block .tonnages were computed. The estimation variances, distribution of errors and histograms of observed and kriged values in each grid Mock were also produced.]

Jan 1, 1983

This paper presents a method for evaluating the economic feasibility of solution mining a hypothetical uranium roll-front deposit. It is assumed the wellfield will be operated in a prudent manner and that leaching tests were performed in depth in both lab and field (push-pull) prior to startup. Leach test results are reduced to two important parameters and used as the basis for solution mining a wellfield. This case study assumes a 10 mil- lion-lb uranium deposit with 40 possible small wellfields; four are kept in operation simultaneously until the deposit is depleted. The wellfields have different ore reserves and grades, lixiviant circulation rates, leach rates, and peak concentrations, and thus the daily uranium production will vary. Daily production is used to assess the profitability of a particular lixiviant and the mode of well- field operation in light of realistic market price estimates. The mathematical procedure is simple and straightforward, based on reasonable in-situ leaching relationships as well as accepted accounting practices.

Jan 1, 1985

By Legett Garrett

Texas Utilities Generating Company (TUGCo) surface mines lignite for use as a boiler fuel at mine mouth generation stations. Currently, the annual lignite production requirement of approximately 28 million tons necessitates mining across approximately 1,600 surface acres each year. The mining operations, located in Freestone, Panola, Titus, and Hopkins counties, Texas, have drastically disturbed some 13,000 surface acres to depths of up to 110 feet since initial startup in 1971. The TUGCo mining philosophy, a commitment made prior to initiation of mining operations and prior to any mining regulations, includes a return of mined-out land to private ownership in the most useful state possible. In the areas of TUGCo operations, the local economies are based upon agricultural production. Historic land use surveys have typically shown a trend from row crop production to pastureland for cattle production. During the 1960?s, the percentage of acreage devoted to row crop production approached zero with respect to the total acreage devoted to agriculture. TUGCo reclamation operations have therefore emphasized restoration of land to a state that is favorable to cattle production

Jan 1, 1982

By Ehsan Alavi, Eren Kusdogan

The City of Toronto’s Coxwell Bypass Tunnel is currently being constructed by North Tunnel Constructors ULC, a joint venture of Jay Dee Canada, C&M McNally Tunnel Constructors and Michels Canada. This project includes construction of approximately 10.5 km of 6.3 meter finished diameter rock tunnel, five 20 meter diameter storage shafts and eleven tunnel connection drop shafts, along with associated deaeration and adit tunnels. This paper describes progress on the project to date and reviews the risk mitigation measures utilized on the project to move the project forward through tough geological conditions during shaft excavation and tunneling phase of the project.

Jun 13, 2023

By Robert L. Bates

In this paper I use the term "industrial minerals" in its broad general sense, and I distinguish two main groups. The first consists of the bulk materials, characterized by low unit price, nearness of deposits to markets, relatively simple methods of extraction and processing, and a tendency to be closely related to the construction industries. The second group includes those materials valued for exceptional purity, or for some special property such as hardness, immunity to acids, or dielectric strength. These materials are produced in smaller amounts, at high unit values, from deposits notably restricted in. distribution; and they require more or less sophisticated methods of production and beneficiation. The applications of this second group are not closely tied to any particular part of the economy. From the way in which the commodity committees of the Industrial Minerals Division are set up, I take it that the chief interest of most members is with the first group of materials mentioned above. Hence this paper will deal mainly, though not exclusively, with such bulk commodities as sand and gravel, clay, and stone. The first word in the title of the paper also requires brief explanation. It is here given a threefold interpretation. First is the role of the industrial minerals themselves in industry; this would probably be taken as the conventional meaning of the title* The second is the role of the industrial-mineral producers as citizens of the community. The third is what may be called the scientific role of these producers.

Jan 1, 1964

By Nick A. Hasenack

A full survey of the laboratory and blast-furnace tests on 2 types of acid pellets is given. From the laboratory tests, carried out in an atmosphere containing hydrogen, it appears that type B, produced out of 100% magnetitic ores, has a far better low temperature disintegration index and a lower reducibility index than type A, produced from a hematite/magnetite mixture. The swelling index, chemical composition and mechanical properties of both types of pellets do not differ significantly. From the blast-furnace test, carried out with a burden consisting of 45% of pellets and 45% of sinter with basicsty ratio about 2.2, and at constant driving rate, it follows that there is no significant relationship between the disintegration value of the pellets and the blast-furnace permeability. If also is concluded that the lower reducibility of the type B pellets leads to a significantly higher coke consumption.

Jan 1, 1975

By A. S. Henderson

Eastern Mesabi taconite is one of the hardest rocks known, but fortunately it shows little tendency to pack in the crushers, when the minus 5/16 inch material is removed. The crushing circuit is essentially as shown in the Engineering and Mining Journal article, "Reserve's New Taconite Project", dated December, 1956 except that the grizzly screen between the two stages of gyratory crushing has been eliminated. The Reserve operating staffs aim is to utilize the crushing equipment in such a manner that the maximum tonnage of taconite can be crushed to the required size at a minimum cost. As is readily apparent, the primary consideration is to produce a desired size product, with the other operating factors to be balanced, thus achieving the best setting for each crusher. Much effort has been expended toward the development of a satisfactory sized material for feeding the rod mills. The characteristics of this feed must allow the following situations to be handled by the existing equipment: 1. The material being fed to the rod mill must be such that it can be fed into the unit with the proper quantity of water to maintain the correct density within the mill. 2. The rod mill must produce a product from this feed which can be handled without difficulty by the magnetic cobbing and ball mill circuit. 3. The incidental tramp must not exceed that quantity which can be handled easily after the rod mill and after the ball mills.

Jan 1, 1959

By L. W. Saperstein

One of the most critical skills developed by underground coal miners is the ability to interpret natural warning signals in terms of impending roof failure. A miner receives a variety of signals which can be called warning and which can be classed broadly by sense: aural, visual, and tactile. This paper concentrates on those signals which are airborne and audible. These signals are creaks, cracks, pops, groans, snaps, booms, tears, rips, and other assorted pulses which emanate from the roof strata, coal pillars, and artificial support in response to the stresses induced by the mine opening. These pulses are sometimes referred to as "talk". Although it is clear that miners rely on roof talk to assess the roof's stability, it is not clear of what roof talk is composed. It has been described in a variety of figurative ways, but has not been scientifically characterized. As will be shown shortly, the purpose of this research is very specific. The ramifications, however, are very broad, and are, indeed, still being followed.

Jan 1, 1974

By Geoffrey Purcell

Improvements which have been made in commericial flotation systems during the past fifty years have resulted more from trial and error methods in the mill than from research in the laboratory. Research has often provided explanations of why mill changes have improved the metallurgical process. Hopefully, in the next fifty years, changes in mill flowsheets will come about, primarily, as a result of research work. However, since minerals, in their infinite variety, cannot be reduced to a standard state, research on commercial ores will have only a local utility, and research on pure minerals will have little commercial application. What will emerge from research on pure systems are mechanisms of adsorption, and this in turn may throw some light on the very much more complex adsorption processes taking place in the pulps of commercial ores. Quartz, without a doubt, has been the subject of more research effort than any other mineral, but we are still a long way from completely understanding its behavior in flo¬tation. Hematite and calcite have received considerably less attention. Ores containing a mixture of all three minerals, however, are commercially important, and the iron deposits in Alabama have been extensively studied by the United States Bureau of Mines (1). The literature reveals no reports of research on synthetic mixtures of all three.

Jan 1, 1967

By Robert Smith

Deposits are global, said Barrick Gold's Smith. This means that the mineral industry, by necessity, is global. "Manufacturers have considerable freedom to decide exactly where they wish to produce whatever it is that they sell," he said. "What we sell, on the other hand, must be produced where nature chose to lay it down. The question is not so much, whether to go global, as when to do it and how to go about it." The timing of international expansion depends on external factors, often political, Smith said, and on internal ones that relate to the company's size and stage of development. "In deciding how to expand, a company is largely deciding how to adapt its existing business strategy to activity on the world stage," he said Barrick entered 1997 with 1.58 kt (51 million oz) of reserves, Smith said, annual production of 93.3 t (3 mil- lion oz) and cash flow of $463 million. Reserves in- creased 40% in 1996 and production will begin to rise again significantly in 1999. "We believe our fundamental strategy is responsible for our early development and subsequent success," he said. Barrick entered the gold-mining industry in 1983. Its corporate mandate was to create shareholder value, Smith said. From the beginning, the company took a different approach - businesslike, entrepreneurial, strategic and focused. "Many mining companies start out with a technical team and develop business and financial expertise thereafter," Smith said. "In 1983, Barrick had the business people, and then moved into mining." First, it acquired part interest in two small operations, one in Alaska and one in Ontario. Then, in 1984, it merged with Camflo Mines, which operated a low-cost underground operation in Quebec.

Jan 1, 1997

By Peter Dietrich, Joseph DeMello, Norbert Fuegenschuh, Kerwin Hirro, Jeff Brandt, Mike Cole

This paper presents a successful case history of the ground improvement efforts and excavation of twenty-three cross passages between twin bore tunnels driven by EPB tunneling machines in Los Angeles, California on Section 1 of the Westside Subway Extension. Unique and complicated ground conditions local to the tunnel alignment include San Pedro sands, siltstone/claystone Fernando Formation, and zones of “asphalt impacted soils.” To provide water cut-off and soil stabilization, jet grouting was performed prior to TBM excavation at the location of many of the cross passages. However, upon investigating the cross passages prior to excavation, the subsurface conditions required additional measures and SEM tools to ensure successful completion of the project.

Jun 13, 2023

By J. D. Cooper

Previous research developed guide- lines to restrict the placement of air velocity sensors to areas of Low turbulence in underground nines. Even though these guidelines are theoretically correct, and may be easy to follow in underground coal mines, their application in small underground metal mines is difficult. As a result, study was undertaken at the Colorado School of Mines Experimental Mine to determine if an air velocity sensor could be placed in other locations with acceptable results. It was found chat by applying a variable calibration function to correct for changes in amounts of turbulence, instead of the previously used calibration factor multiplication, the sensor could be used successfully in areas of moderate turbulence.

Jan 1, 1984

By J. P. Morgan

The Vesta Preparation Plant of the Jones & Laughlin Steel Corporation is located on the Monongahela River, eight miles south of Brownsville, Pennsylvania. This plant is capable of cleaning 2400 NT/hr of a mixture of Pittsburgh seam high volatile coals from the Vesta and Shannopin mines to produce a metallurgical coal of 6.75% ash and a steam coal containing 14% ash. Heavy media vessels are utilized to upgrade the coarse coal while launders and tables. handle the -1/4" fraction of the raw coal feed. Cleaned -coal goes to boot classifiers where the +48 mesh material settles and is removed by bucket elevators. This 1/4 x 48 mesh material is then sent to centrifugal driers for dewatering. As designed, the minus 48 mesh fraction overflows the boot as a 7 to 8% solids slurry and is recovered by cyclones and a thickener and dewatered by filtration. The-products of the heavy media circuit, the launder-table-boot-drier circuit and the cyclone-thickener-filter circuit are combined to constitute the shipped metallurgical coal. This Vesta-Shannopin mix is combined at J&L's Pittsburgh and Aliquippa Works with purchased low and medium volatile coals for the production of metallurgical coke.

Jan 1, 1962

By Daniel McNamee, Wern-ping N. Chen

The Amtrak East River Tunnels include four tunnels, Line 1 to Line 4, which extend from New York Penn Station in Manhattan, under the East River to Sunnyside Yard in Long Island City. Since fall 2015, Amtrak has initiated a program to repair and reconstruct the century-old tunnels, including structural repairs of all the tunnels and reconstruction of the Line 1 and Line 2 tunnels. The reconstruction includes bench wall demolition and replacing and installing the following elements in the tunnels: direct fixation track, traction power, signal, communication, and tunnel fire/life/safety components. This paper provides design and site investigation challenges and knowledge gained from this program.

Dec 1, 2022

By D. W. Smellie

This paper is a review of technological progress in mining geophysics during the past decade. This has been the most significant period in the history of mining geophysics. Among the already existing; techniques, instruments for ground -magnetic and electromagnetic prospecting, were developed that are more, portable and faster to operate. Induced polarization equipment came into widespread use. Airborne instruments of various types became available and were used to survey large areas. Drillhole instruments were developed and have had some use, and it is to be hoped will be used to a greater extent in the future. Two revolutionary new methods, the AFMAG and INPUT, were developed. The wisdom of attempting to cover such a broad field in a single paper might be questioned. There is the inevitable problem that each topic must be discussed very briefly. However, while papers describing individual instruments have appeared, many have yet to be described in the technical literature. The evolution of the ground magnetometer and electromagnetic instruments has not been discussed. It is only recently that a review article has appeared on airborne EM. The existence of review literature on some topics has meant that they are given less emphasis in this review than those topics inadequately covered. It will also be observed that stress is laid on "chose instruments that are generally available to the mining industry rather than those developed by individual exploration companies for their own use.

Jan 1, 1963

By Cahit Helvaci, Robert B. Kistler

Borates are defined as ' 'salts or esters of boric acid; a compound containing the radical B203" (Bates and Jackson, 1987). Borates are defined by industry as any compound that contains or supplies boric oxide. A large number of minerals contain boric oxide, but the three that are the most important from a worldwide commercial standpoint are: borax, ulexite, and colemanite. These are produced in a limited number of countries (Fig. 1), dominated by the United States and Turkey, which together furnish about 90% of the world's borate supplies (Lyday, 1991). Production in the United States originates in the Mojave Desert of California; borax and kernite are mined by US Borax from its large deposit at Boron. Borate containing brines are pumped from Searles Lake by North American Chemical Co., and a limited amount of colemanite is mined by Newport Mineral Ventures from Death Valley. Turkish production is controlled by Etibank, the national mining enterprise, which supplies most of the commercially traded ulexite and colemanite from mines in the Bigadic and Emet Districts, plus borax from the huge deposit at Kirka. Borate minerals have been employed in a wide range of uses for many centuries, dating from at least the 8th century when they were used primarily as a flux for assaying and refining gold and silver. Their valuable properties and relative rarity soon stimulated international trade in borates; Marco Polo claimed to have trans- ported Chinese borate minerals from Tibet to Europe, and his home port of Venice was the center for borate imports and use throughout the Middle Ages (Travis and Cocks, 1984). Borates were traded at relatively high prices for highly specialized applications into the late years of the 19th century. At that time they were being used for medicines, food preservatives, ceramic glazes, and in expanded applications as metal fluxes. It was in that era that borax was discovered in Clear Lake, CA, and more significantly, the playa deposits of western Nevada were found and exploited by F.M. "Borax" Smith and others. Research and development by Smith's company began the evolution of borates from a high priced commodity with a few specialized uses to the relatively low priced chemical raw material used in large tonnages on a worldwide scale today. Borates are often defined and sold by their boric oxide or B,03 content, and most statistical data are listed in tons of B203. Of the products sold by the industry, borax pentahydrate or 5 mol and boric acid are the most commonly traded commodities. Boric acid plants are operated by all of the major borate producers. Glass fiber insulation is the major end use in the United States followed by textile glass fiber and borosilicate glass, detergents, and ceramics. Detergent usage continues to be a major end use in Europe.

Jan 1, 1994

By Daniel T. Hegyan

The employment of continuous rotary vacuum disc filters to filter refuse from the fine coal washing circuits has been increasing as it has become more important to close the water circuits and eliminate sludge holding ponds. This paper will discuss our past experience filtering refuse, effects of solids concentration in the filter feed, use of polymer flocculation aids, effect of flocculation devices, and effects of particle size and ash content on the filtration rate. Detailed tests were performed on existing installations utilizing coal refuse filters to determine optimum flocculant dosage, solids concentration, and disc rotation speed to form a dischargeable cake. Information was also obtained showing effect of flocculant addition on the moisture of the filter cake. Our test work has shown that the continuous filtration dry cake rates for fine coal refuse correlates very well with the data developed and presented by Silverblatt and Dahlstrom1 except that the curves have moved up the scale by use of polymer flocculant additions. These polymers were not available at that writing. Finally, our tests also confirmed the general premise stated by S. K. Mishra2 that controlled additions of polymer flocculants will reduce filter refuse cake moistures somewhat.

Jan 1, 1974

By Earl R. White

In 1950 Kaiser Steel Corporation acquired control of the Utah Fuel Company, a pioneer Utah coal concern owning large reserves of high volatile coking coal near Sunnyside, Utah. The mines at Sunnyside have been producing high quality coking coal since the late 1890's. Kaiser Steel acquired the coal deposits at Sunnyside in order to supply the necessary coke for its steel plant at Fontana, California. The Sunnyside coal deposits are made up of two mineable beds, the upper and lower Sunnyside seams. Both seams outcrop along the southward facing escarpment of the Book Cliffs. The coal seams dip under the massive sandstones of the Book Cliffs to the northeast at 5 to 22 pct., with the steepest-part being near the outcrop. Mining at Sunnyside up to 1961 had been carried on with room and pillar methods. The deep cover and rotten roof conditions, along with the need of increased tonnage, required a change of mining technique. Numerous ideas were presented, discussed, and economically analyzed. Several people involved in these discussions, with the aid of W.W. II, had been introduced to the European methods of coal mining, namely the longwall technique. The European mines had long been plagued with near similar conditions as those at Sunnyside, particularly the deep cover problem. The longwall method seemed to be working very well under these conditions, and with the extensive studies given longwalling by the Kaiser Steel mining officials, it was decided to give longwalling a try.

Jan 1, 1976

By R. Addison, T. Swendseid, R. Kehmeier, D. Larsen, J. Uhrie

"The development of a mining project necessarily progresses through many steps, beginning with the identification of a mineral resource and continuing through project construction. Several classifications of engineering study development are described, including preliminary economic assessment (PEA) or scoping studies, prefeasibility studies (PFS), feasibility studies (FS) and regulatory codes, each with a specific project organizational objective. This paper addresses the PEA, PFS and FS types of reports that are used by companies to evaluate projects, meet regulatory requirements and seek financing. The minimum requirements for engineering studies, focusing on the needs of financial institutions considering investment in a project, are outlined. IntroductionThe financing of mining projects in recent years has come under increased scrutiny by financial institutions owing primarily to an increasing percentage of projects whose capital expenditures had overrun project budgets or had failed to produce the economic returns anticipated during the project development process. Often, unfavorable project outcomes are not the result of widespread failures of the project engineering process but arise from inadequate engineering in limited specific areas of the project scope, such as overestimated mineral reserve, inadequate mine design, insufficient metallurgical testing or underestimated capital costs. Mill facilities and process infrastructure typically are responsible for up to 80 percent of the capital expenditures required by greenfield mining projects. They are often the project areas where capital costs are inadequately developed, and consequently are the areas highly scrutinized by financial institutions. This paper offers a perspective on the level of engineering expected by financial institutions as a prerequisite to committing support to developing mining projects.The evaluation of a mining project from exploration through development and production is a lengthy and complicated process. Mine development commitment activities for a potential project are initiated when a mineral resource is identified and continue through to the start of construction. The technical feasibility and the economic viability of each project are determined during the phases of mine development with more detailed engineering data required at each stage. There are at least four levels of engineering studies during development that are commonly acknowledged by the mining industry:"

Jan 1, 2016