Search Documents

By Arshad Ali, Mudassar Khan, Waqas Ahmad, Nisar Muhammad, Muhammad Salman

Talc is an important industrial commodity due to its wide-ranging intrinsic properties; however, the presence of iron oxide hinders its industrial utilization. Herein, we report the purification of Pakistani talc through acid leaching assisted by chlorination techniques. Among various acids (i.e., HF, HCl, H2SO4, HNO3, H3PO4, Aqua Regia, H3BO3, and CH3COOH), HF was the most effectual, removing up to 67% of iron oxide at optimized conditions of temperature, 90–95 °C; time, 120 min; HF concentration of 5%; and at a pH of 1. In the second step, chlorination of the talc sample was performed separately by both wet chlorination and dry chlorination. Wet chlorination was carried out using KMnO4 and HCl in slurry phase which shown about 52% removal of iron oxide, whereas dry chlorination with CaCl2 at high temperature attained about 48% removal of iron oxide from talc sample. Further, the wet chlorination of HF leached samples was also performed under optimized conditions which showed up to 87% iron oxide removal. The original and treated talc samples were characterized by EDX and XRD analysis to monitor the changes in the elemental and mineralogical composition of the talc. It can be concluded that HF leaching followed by wet chlorination is an effective method for the upgradation of low-grade Pakistani talc ores.

Aug 9, 2021

By John J. Friel

The addition of dolomite to iron ore pellets improves their high-temperature reduction properties primarily by increasing their reducibility and raising their softening temperature. In this study we prepared dolomite-fluxed pellets from three different concentrates; Hibbing, a magnetic taconite, Knob Lake, an earthy hematite; and Carol Lake, a mixture of specular hematite with magnetite. The composition n of the concentrates is given in Table I. The pellets were subjected to standard physical tests and the following reduction tests: low temperature degradation, swelling, softening, and thermogravimetric analysis. Petrographic examination and electron microprobe analysis allowed us to evaluate the effect of composition and firing on the phase assemblage. Further, we were able to interpret the test results in terms of chemistry and microstructure. This approach enabled us to determine which fluxed composition best suited each of the concentrates.

Jan 1, 1980

By Steve Kral

The concept of sustainable development is not new to the mining industry. Many people involved with mining have argued that the industry throughout the world has always supported the communities where they operated. They say that the mining industry was employing sustainable development practices before the phrase became fashionable. The mines employed residents and supported the local economy through tax payments and the purchase of goods and services from local businesses. In many cases, mining companies have built medical facilities and contributed money, equipment and services to local schools. In modern times, mining companies have donated reclaimed land to the local communities for use as parks and recreational facilities.

Jan 1, 2004

By Jean-François Boucher, Ernest K. Yanful, Mei Lin Shelp, Lionel J. J. Catalan

Shallow water covers for preventing acid production in tailings are based on the principle of minimizing oxygen availability. Resuspension of material from the tailings bed may result in increased oxidation and metal releases since dissolved oxygen is at near saturation levels in the water cover. Resuspension can be caused by waves and currents strong enough to mobilize the surface of the tailings bed. Tailings resuspension was measured with sediment traps in the Upper Cell of the Heath Steele site near Mirarnichi, New Brunswick Canada. Although significant amounts of resuspended tailings were collected in all traps, analysis of resuspended solids and bed tailings suggests that for the observed wind conditions resuspension did not occur at locations where the water cover depth was greater or equal to 1.0 m. Currents were likely responsible for the transport of resuspended tailings from shallower areas to locations where the water cover was deeper than 1.0 m.

Jan 1, 2000

By Oleg N. Tikhonov

A new extraction method which includes a combination of gravity and alternating electromagnetic fields with interfriction of mineral particles was proposed (Tikhonov O.N., 1979) and tested in lab conditions at Mineral Processing Department of St. Petersburg Mining Institute. At the beginning of the work the main goal was to find an efficient alternative to traditional extraction methods (like shaking table, etc.) used for concentration of fine alluvial gold particles. After the method and a series of gradually improved lab separators (Tikhonov, et al., 1983) were positively tested for gold (Tikhonov, et al.. 1986) the efficiency of the method was also proved for extraction of and other heavy minerals from alluvial and ground ores in experimental work at the St. Petersburg Mining Institute. The fine heavy minerals were separated to concentrates with high technological indices (Andreev et al., 1987), (Tikhonov, Gladkov, 1987), (Tikhonov, Gladkov 1989). In parallel a semi-industrial gravi-electro- magnetic separator was made and several technological flowsheets were designed for testing the method in industrial conditions (Tikhonov O.N., Miazin B.N., 1987), (Tikhonov O.N., Tolstunov S.A., Jebelev V.V.,1989). A series of industrial tests accompanied with complete sampling and standard technological measurements were performed at several alluvial deposits, with good technological indices. Thus the method and the flowsheets displayed high additional recovery of fine alluvial gold particles during elkrated industrial experiments in Siberia (Aldan province). At higher concentrate grade this method, even in one-stage operation, increased gold recovery more than by 25% compared with shaking table (for particles -0.10 mm gold recovery was 82% vs. 55% by shaking table, for particles - 0.25mm the recovery was 97.5% vs. 61.8%). Experiments were performed by joint team of St. Petersburg Mining Institute and the Irkutsk Institute of Rare Metals (Tikhonov O.N., Gladkov S.A., Tarasova T.B., 1991).

Jan 1, 1995

By Russell Frith

A review of published literature reveals case histories whereby the entire periphery of a coal pillar has “burst” out as a single event during first workings, the associated energy and material release causing significant damage to adjacent roadways and any equipment/infrastructure located within said roadways. Such events are distinct from coal burst events during first workings such as that at the Austar Mine in 2014, or those linked to overburden bumps related to either horizontal stress-driven slip along major faults and/or thick, massive strata units in the overburden or floor of the coal seam.

By N. B. Aughenbaugh

The People's Republic of China has 582 Gt (641 billion tons) of proven coal reserves. At present, 576.5 Mt (635.5 million tons) of coal are mined a year which makes China the third largest producer of coal in the world. Underground mining accounts for 95% of the total production. This paper will discuss the coal districts, coal types, jurisdiction of coal mining, and methods of underground mining. The article also will outline China's objectives in future planning and development of its coal reserves.

Jan 1, 1982

By Hemendra N. Kalia

To plan a safe and efficient coal mining operation, the design engineer should use all the available information regarding the property to be exploited. The reliability of the mining operation must be as high as possible so that the plants relying on the coal can operate at the maximum design capacity. A good design should incorporate all of the known geological characteristics of the deposit, the structural and physical properties of the coal, as well as the rock which will form the roof and floor of the mine openings. A systematic method is proposed as a guide to insure a mine design that will be safe, efficient and will minimize surface disturbances resulting from mining operations. It is anticipated that the method proposed will result in maximum extraction at perhaps minimum cost to the operator. In general, to develop a mining area, several factors are systematically reviewed: (1) determination of the economic minability of the deposit, (2) the computation of the coal reserves, (3) the marketability of the coal, and (4) the life of the property. In general, boreholes are drilled in a predetermined pattern and geophysical or geological methods are used to log the boreholes. The information so obtained is primarily used to determine the quality and the extent of the deposit and to determine to some extent such geological features as faults, barren areas, washouts, and channels.

Jan 1, 1973

By Marco Sonnenschein

Belt conveyors for tunnelling are industry standard and key to high performance of TBM drives. Conveyors reduce traffic in the tunnel and increase safety in the tunnelling process. This paper will illustrate the state of the art of tunnel belt applications in very long and curvy tunnels like the Coxwell Bypass Tunnel Project in Toronto, Canada.

Jun 23, 2024

By D. A. Dahlstrom

Since the initiation of continuous vacuum filtration over a half a century ago, control of the performance of these units has been largely in the hands of the plant operators, Obviously there has been the introduction of variable speed drives, adjustable speed feed slurry agitation, vacuum control, etc. However, control of , filtration rate, cake moisture content, dissolved solids recovery by cake washing and dryness of solids where thermal drying is practiced is primarily up to the operators judgment and the settings he imposes on the controls he regulates, - filter cycle time, submergence, vacuum level, filter medium condition, wash water- rate, and other such factors. While this may seem to indicate that good operators are a paramount necessity, and certainly always desirable, a considerably more vital factor is a properly designed filter and filter station for the particular application. With improper design, highly skilled operator control will still leave much to be desired in the way of process performance. On the other hand, with correct design and application, the operator can easily and quickly control normal plant surges and quality variations within the flow sheet. Due to the growing complexity and inter dependency between the various processing steps in the modern flow sheet as well as the rising costs of capital investment, labor, maintenance, and losses involved with off quality product or insufficient recovery, automatic or inherent performance control of many of the unit operations within the metallurgical mill must be achieved. Continuous filtration should and can be susceptible to such control. However, as every instrument engineer knows, before control and automation can be achieved, a basic understanding of the operation is mandatory. This is primarily due to three factors. First, as in so many control applications, it may not be possible or feasible to measure the factor that it is desired to control. Thus, secondary variables that influence the major factor are substituted for control purposes. Secondly, it is always desirable to take advantage of any ?self-regulation? within the operation being performed on the equipment. In so doing, not only will automatic control be facilitated, but instrumentation is minimized while experiencing most efficient operation. Finally, automatic control is not a cure-all for improper process and equipment design and application. Hanging instruments on such an operation can be compared to constructing a sizable building on sand, Results will be disappointing.

Jan 1, 1960

By I. Duckworth

P.T. Freeport Indonesia operates a mining complex located in the highlands of Papua, Indonesia. This district consists of underground and surface operations. The East Ertsberg skarn system (EESS) is one of the major orebodies in this district. Subsurface caving of the EESS has been carried out in a systematic series of mining lifts dating back almost 30 years. Present production from the third lift deep ore zone (DOZ), has reached 80 kt/d (88,000 stpd) during 2010, with this rate sustained through 2015. The orebody was proven below the existing caving level, with the next vertical block called the deep mill level zone (DMLZ).

Jan 1, 2010

By R. E. Hamilton

Automation is a word whose meaning has been broadened by popular usage to include any labor saving device. We with restrict our usage to the replacement of human judgement by instrumental measurement and mathematical analysis in the control of industrial processes. Mineral concentration is an area which has resisted automation because of the great difficulty in developing measuring instruments which can exist in the rugged environment and can measure useful properties with acceptable accuracy. This is not the only factor limiting progress, but until recently it has been of over-whelming importance. The development of on-stream X-ray analysers, magnetic flowmeters and nuclear density meters for mineral slurries has eliminated this obvious barrier and is enabling us to locate and attack the less obvious problems which still limit our ability to automate concentrators. If we examine the history of automation in industries which are highly automated we find that it has usually gone through three distinct phases. The first phase has been regulation. This is the simplest form of control and involves manipulating some variable whose value is of no importance in order to maintain the value of some other variable which is important at a constant specified value in spite of disturbances which may occur in other variables which affect it. A simple example is the use of a control valve to maintain a constant flow of fluid in a line in spite of changes in pressure in the vessels at the ends of the line. The position of the valve stem is of no consequence, as long as it is within its operating range. Unfortunately we soon run out of variables which can be

Jan 1, 1971

By Charles W. Merrill

The price records of 7 representative mineral commodities for the 68-year period 1890 through 1957 have been compiled and analyzed for significant trends. When reduced to real prices in terms of dollars of constant purchasing power or to the purchasing power of industrial wages at average rates, a substantial overall fall in prices is revealed. This downtrend contradicts the widely held concept that, heavy drafts on a mineral resource must lead to scarcity, reflected in rising prices. Three metals (aluminum, copper, and pig iron), two fuels (bituminous coal and petroleum)', and two nonmetals (sulfur and cement) have been chosen because of their preeminence in their respective categories, their significance in an industrial economy, and the ready availability of their price records. It might be added that these seven commodities. were selected before any price figures were compiled, none was selected or rejected to substantiate any preconceived notions as to price trends, The overall importance of the seven is demonstrated by the fact that, taken together, they composed over three-fourths of the value of all minerals produced in the United States in 1957. The first step in the analysis was to reduce the price records to a basis for significant comparisons, Two such comparisons have been made: (1) The quantities of each of the commodities that could have been purchased for an average hour's wage in each year; and (2) the unit price of each commodity through hhe years in terms of deflated dollars. These data are set forth in the accompanying table and two charts.

Jan 1, 1959

By Dennis W. Leonard

Let us begin our discussion by looking at historical and current levels of sales of both natural and synthetic zeolites on a world-wide basis. Due to the understandable reluctance of some companies to disclose sales data, some estimation has been necessary regarding the tonnages and values shown in Table 1. We are confident, however, that they are within acceptable limits, especially the numbers referring to natural zeolite.

Jan 1, 1979

By Albert E. Ketler

The AirBoss*200 is a unique ambient airflow sensor with important improvements in accuracy, especially in the critical low end, 0-61 m/min (0-200 fpm) where MSHA regulations apply. All solid state, its design is rugged, and there are no moving parts or delicate filaments. An on-board microprocessor calculates air velocity, linearizes and corrects for temperature, while driving voltage and current loop analog outputs to .3 meters/minute (1 ft/min) resolution. Recent developments also cover both positive and negative flow directions. A hand held computer is available to readout data and to adjust stored range selection, alarm set points, calibration data and the speed of response. Installation in hazardous areas is covered by MSHA Classes G, H and L.

Jan 1, 1993

By William Gleason

For the first time in many years, the Liebherr Group chose to host its annual conference for the international construction trade press in the United States. The reason for the move is simple ? mining. Like other large corporations, especially those in the construction fields, Liebherr felt the effects of the global economic crisis that began in 2008. The slowdown in the housing market was especially hard on Liebherr?s mobile crane and earth moving divisions. The mining division, however, while affected by crashing commodity prices that led to cancelled orders and the loss of financing for some customers, was not battered as badly as the other divisions. And now, with the price of commodities once again on the rise, it seems that it will be Liebherr?s largest machines that lead the family-owned company to better days. ?We can report that our generally optimistic view during the crisis has proved adequate,? said Joachim Janka, president of Liebherr mining equipment, at the conference in Williamsburg, VA, just down the road from the company?s mining truck division global headquarters in Newport News, VA. ?Since the third quarter of 2009, our mining equipment activities have been recording once more a strong and steady demand. This has already yielded a substantial increase in market shares for our product lines of large mining shovels as well as for mining trucks.?

Jan 1, 2011

By A. Jennings, J. Cornet, P. Perrone

Controlling long overland conveyors with multiple drive stations is a complex problem. The methods for controlling these belts in a steady state are well-covered in existing literature, but a discussion of starting and stopping strategies is absent. This paper outlines different control strategies for starting, stopping and running conveyors with multiple drive stations. To illustrate the benefits of applying the methods described in this paper, the authors show how their adoption corrected many of the control system problems at Essroc Cement’s overland conveyor, which features three drive stations separated from each other by long lengths of continuous conveyor belt.

Jan 1, 2013

By William H. Lehr

In recent years, we have witnessed many innovations in the equipment used in handling bulk materials. Not too long ago, any sizeable stockpile of coal or iron ore was attended by one or more material handling bridges. More recently, large stockpiles have been built with mobile equipment of' the earth moving type with bulldozers and front end Loaders being utilized in reclaiming operations. The most recent stocking and reclaiming device is the rotary bucket wheel machine. The early bucket wheel machines built in the United States were developed for the strip mining of coal. We understand that the first American machine was built in the Midwest in 1944. This type of unit was developed in an effort to reduce the cost of removing overburden and to provide satisfactory spoil disposal. As the available coal reserves under shallow cover were exhausted, the cost of removing the deeper overburden with conventional equipment became too great for these operations to continue profitably. The first machine has now been followed by six or seven additional units, the largest of which can handle material at a rate of more than 7000 cubic yards per hour.

Jan 1, 1965

By Donald R. Williamson

Statistical studies at Cyprus Pima Mine indicate that samples from 22 blastholes are necessary for determining average copper grades, within a desired range of precision, for mine-model blocks by arithmetic averaging. The average number of holes in such blocks is 14. Many considerations show that more holes will not be drilled for sampling. A way to determine block grades more reliably than by" arithmetic averaging was sought. Thus far arithmetic averaging has proven to be the best procedure for the particular operation characteristics despite the small number of samples. It naturally follows that expenditure of great effort in sampling blasthole cuttings is unwise.

Jan 1, 1977

By R. Schlüter

"The “Biohydrometallurgical Center for Strategic Elements (BHMZ)” is a cooperation of 13 departments of the Technical University Bergakademie Freiberg fostering interdisciplinary research along the whole (bio-) hydrometallurgical process chain to extract indium and germanium from sulphide ores. Research comprises methods to (i) bring the respective metal from the source material into aqueous solution and (ii) different approaches to extract pure metal or metal-containing materials from the solution. Within the BHMZ the Department of Underground Mining Methods deals with the design and implementation of an underground testing facility for bacterial in-situ stope leaching in its own “Research and Educational Mine”. The intention is to investigate innovative approaches for leaching technologies by crack initiation due to hydraulic fracturing or water pressure blasting under consideration of leaching kinetics and underground conditions. It is planned to set up two testing units comparing energy input and the metal output of conventional (blasting) as well as one of the innovative technologies. Aim of subproject is to establish an innovative and sustainable method ready for up-scaling. BACKGROUND Metals like copper and zinc mainly occur as sulphide ores in nature. Due to the insolubility of these sulphide minerals the respective metal is commonly extracted by pyrometallurgical processing methods. These methods require several steps of enrichment of concentrates such as flotation and roasting (Figure 1) under extensive energy utilization. Additionally, this arouses the emission of sulphur dioxide gas which can have a negative impact on the environment in form of acid rain, as long it is not caught by sulphuric acid facilities (Schippers et al. 2011). However, to treat the ore on the surface either open pit or underground mining operations are necessary. This implies operation steps from excavating, loading, and conveying/hauling, to dumping with the sub-processes crushing and stashing. Due to the tendency of increasing depth, more complex ores and decreasing ore grades of the mineable deposits as well as increasing energy and environmental costs these conventional mining and processing methods become in general more costly and difficult to apply. Hence, hydrometallurgical processes and especially the suitability of bioleaching as an alternative in-situ method for future mining projects should be examined. Leaching by means of microorganisms is a combination of mining and processing by converting the insoluble metal into an aqueous form. This technology is an economically beneficial and environmentally friendly alternative to pyrometallurgical processing methods especially for primary and secondary low grade ores. Mainly the extraction of copper but also of zinc and lead from sulphide ores is state-of-the-art in surface leaching operations like heap and dump leaching (Figure 1)."

Jan 1, 2015