Search Documents

By F. N. Kissell

U.A. Mine Safety and Health Administration (MSHA) coal dust compliance data sometimes shows high silica levels at roof bolters. However, it is unclear whether this silica normally originates from the bolter itself or from other dust sources upwind of the bolter research studies to answer this question at individual mines have been conducted. However, operational practices vary from mine to mine thus, the information gleaned from any one study cannot be accurately extrapolated to describe silica dust sources in most mines. In this paper, three decades of bolter dust research are reviewed the results showed that, while inadequate maintenance on the bolter dust collection system can result in excessive dust, more likely reasons for high silica levels are inadequate ventilation of the mine entries being bolted and dust traveling downwind from the continuous miner to the bolter. Scrubbers on continuous miners may not be removing as much silica dust as expected. Mining Engineering, 2011, Vol. 63, No. 10, pp. 78-82. Official publication of the Society for Mining, Metallurgy and exploration, Inc.

Jan 1, 2011

By Natalie White, Joel Asp, Allyz Kramer

"Minnesota has robust reclamation standards and have proven results in the taconite mining industry. Reclamation of overburden spoils, lean ore spoils and fine tailings from taconite production has generally been successful on the Iron Range, using a low input standard reclamation practice. Success at reestablishing vegetation on these landscapes is likely due to fairly favorable chemical and physical properties (e.g., few limitations due to acidic generating materials, metal toxicities and water and nutrient holding capacities). However, coarse tailings reclamation has proven more difficult, presumably due to lower nutrients and challenges with moisture holding capacities. Research efforts conducted since 1990 have struggled to develop a reclamation strategy for coarse tailings that meets the Minnesota Mineland Reclamation Rules, Chapter 6130. However, new breakthroughs in scram mining technologies are producing fine and coarse tailings that have not been encountered nor reclaimed in northern Minnesota. Scram mining in Minnesota is defined as those mining operations that produce natural iron ore concentrates. Innovative research is underway to investigate and determine successful reclamation strategies to reclaim scram mining tailings from these scram mining operations. The research program is conducted through collaboration with SEH, Prairie Restorations, Inc. (PRI) and Mining Resources, LLC with funding support from the Iron Range Resources and Rehabilitation Laurentian Vision Partnership minescapes grant program.The research program was divided into three phases:Phase I. Bench-scale testing to identify successful treatments to reclaim and restore scram tailings through evaluating surface soils amendments, viable seed mixes and plant germination, growth and densities. Phase I was completed in early 2015.Phase II. Field-scale pilot trial to test larger scale effectiveness of the treatments deemed successful in Phase I and test various vegetative assemblages and planting techniques focused on the unique challenges with scram tailing basins. Phase II was completed in late 2016 with a summary monitoring report.Phase III. Produce a technical report of results for the research undertaken in this study, as well as compile prior reclamation results used during previous Minnesota iron mining reclamation projects on tailings basin applications. Phase III was completed in 2017 with a summary monitoring report and recommendations."

Jan 2, 2018

By H. R. Manouchehri

In flotation practices, as particles become finer, such as smaller than 20 μm, process efficiency declines markedly. Selective agglomeration of fine particles is a technique to enhance the recovery of fine valuable minerals in flotation circuits. Different agglomerating methods have been introduced and tested. One method that has recently received much attention is to make use of magnetic force to aggregate fine particles. A selective aggregation of fine paramagnetic particles, such as sulfide minerals, can be achieved in the high-intensity magnetic field prior to or during flotation. The method is simple, selective and effective for fine particles and has low operational cost, though a minimum magnetic susceptibility for fine grains is required to promote the process. In this paper, the implementation of the ProFlote magnetic conditioning device in Boliden’s Garpenberg old concentrator in Sweden, where a complex massive sulfide ore is treated, is presented and discussed based on Boliden’s Garpenberg plant. The results showed an increase in the flotation recovery of fine valuable minerals. Zinc (Zn) production was increased by between 1,100 and 1,500 t/a, while salable yearly silver (Ag) production was increased by 1,500 kg. The copper (Cu) grade in the final concentrate was increased by 1 percent, while reductions in its Zn and lead (Pb) grades were obtained. Moreover, considerable reduction in Zn deportment to the final tail was observed

By D. Govender

In recent years, economies of scale have continued to drive copper projects to larger throughputs to offset depleting lower grade resources. A decade ago, there were only a small number of projects that stretched beyond 100 kt/d (110,000 stpd) throughput rates. Today, and moving forward, virtually all the major copper projects are sized beyond this, with throughput rates up to 250 kt/d (275,000 stpd) now under evaluation for a number of key projects in Chile and Peru. This paper explores the development from the 160 m3 (5,650 cu ft) flotation cells, through to the 257 m3 (9,076 cu ft) cells and to the current 660 m3 (23,380 cu ft) machines. The contributions of specific copper concentrators to this growth phase are reviewed in this article. The historical basis of flotation machine scale-up is also briefly discussed. Metallurgical results as well as layout, maintenance and operational aspects are highlighted.

Feb 1, 2014

By Thomas R. Mills

Under contract to the U. S. -Department of.-Interior, Office of Coal. Research, Hittman Associates recently completed a 16 month study of the environmental-factors associated with the siting, construction, and operation of large scale coal refineries. (1 2) The objective of this study was to identify the environmental effects and to define the magnitude of these effects and the approaches which can be used to mitigate adverse environmental consequences. In the study, the five major coal bearing regions of the country having reserves adequate to support a number of large scale coal refineries were considered. The regions considered were: Appalachian, Eastern Interior, Fort Union, Powder River, and Four Corners.

Jan 1, 1975

By J. Kretschmann, K. van de Loo, J. Brune

In 2018, the German Federal government decided to phase-out the energy production using coal-fired power plants and to terminate lignite mining completely by 2038 at the latest. This decision will impact approximately 60,000 jobs. It will have an enormous impact on the socioeconomic development especially in all German lignite mining regions. To avoid economic and political friction, it is of utmost importance to achieve a sustainable transition towards a post-mining era and to offer residents in the mining districts perspectives for a good future that include adequate job opportunities. In this context, the German government is providing massive structural aids early on. As previous closure experiences from the German hard coal mining industry have shown, it takes at least a generation to overcome the effects of a strategic closing decision of this magnitude. Therefore, the planned closure process appears to be a long time at first glance. In fact, however, it is not.

Mar 2, 2022

By K. V. Raj, VASU GANGRADE

Airflow in large-opening stone mines is largely dependent on the natural ventilation due to the large cross- section area of the opening. The openings of such stone mines are typically twice or thrice the size of typical underground coal or metal/nonmetal mines. Due to the influence of natural ventilation, air velocities as well as the static pressure drop in the mines are low. Mines rely on auxiliary fans to ventilate active faces to reduce contaminant exposure to mine workers. The National Institute for Occupational Safety and Health (NIOSH) is conducting research on ventilation of large-opening stone mines to reduce worker exposure to dust and other contaminants such as diesel particulate matter (DPM). In order to reduce worker exposure to dust and DPM, an understanding of the airflow pattern due to auxiliary fans in the mine is needed. Under this research, NIOSH researchers are exploring the computational fluid dynamics (CFD) modeling to understand the airflow behavior in large-opening mines. In this paper, the team is presenting the results from three-dimensional CFD modeling of airflow in a large-opening stone mine and investigating the effect of a fan placement with the movement of trucks.

Feb 1, 2025

By J. Simmons, P. Ziemkiewicz

Acid-Base Accounting (ABA) is an analytical procedure that provides values to help assess the acid-producing and acid-neutralizing potential of overburden rocks prior to coal mining and other large-scale excavations. This procedure was developed by West Virginia University scientists during the 1960s. After the passage of laws requiring an assessment of surface mining on water quality, ABA became a preferred method to predict post-mining water quality,and permitting decisions for surface mines are largely based on thevalues determined by ABA. In order to predict the post-mining water quality, the amount of acid-producing rock is compared to the amount of acid-neutralizing rock, and a prediction of the water quality at the site (whether acid or alkaline) is obtained. We gathered geologic and geographic data for 56 mined sites in West Virginia, which allowed us to estimate total overburden amounts, and values for maximum potential acidity (MPA), neutralization potential (NP), net neutralization potential (NNP), and NP/MPA ratios for each site based on ABA. These values were correlated to post-mining water quality from springs or seeps on the mined property. Overburden mass was determined by three methods, with the method used by Pennsylvania researchers showing the most accurate results to actual overburden mass. A poor relationship existed between MPA and post-mining water quality, NP was intermediate, and NNP and the NP/MPA ratio showed the best prediction accuracy. In this study, NNP and the NP/MPA ratio gave identical water quality prediction results. Therefore using NP/MPA ratios, values were separated into categories: <1 should produce acid drainage, between 1 and 2 can produce either acid or alkaline water conditions, and >2 should produce alkaline water. On our 56 surface mined sites, NP/MPA ratios varied from 0.1 to 31, and six sites (11%) did not fit the expected pattern using this category approach. Two of eight sites with ratios <1 did not produce acid drainage as predicted (the drainage was neutral), and four of 40 sites with a ratio >2 produced acid drainage when they should not have. These latter four sites were either mined very slowly, had non-representative ABA data, received water from an adjacent underground mine, or had a surface mining practice that degraded the water. In general, an NP/MPA ratio of <1 produced acid or neutral drainage sites, between 1 and 2 produced mostly alkaline drainage sites, while NP/MPA ratios of >2 produced alkaline drainage with a few exceptions. ABA is a good tool to assess overburden quality before surface mining and to predict post-mining drainage quality after mining. The interpretation from ABA values was correct in 50 out of 52 cases (96%), excluding the four anomalous sites, which had acid water for reasons other than overburden quality.

Jan 1, 2003

By Meredith Scaggs, Emily Sarver, Lucas Rojas Mendoza

"Early on Jan. 9, 2014, approximately 37,800 L (10,000 gal) of crude 4-methylcyclohexanemethanol (MCHM) leaked from a storage tank sitting on the bank of the Elk River near Charleston, WV (WVDEP, 2014; CSB, 2014). MCHM is a chemical commonly used in preparation of fine coal and is considered nonhazardous in terms of transportation, storage regulations and also toxicity (CDC, 2014a). Freedom Industries Inc., a producer and vendor of specialty chemical products, had acquired the storage facility from Etowah River Terminal, LLC just a few weeks prior in December 2013 (WVDEP, 2014; Freedom, 2005). The direct cause of the spill was ultimately determined to be two small holes in the base of the 76-year-old tank, which were created due to corrosion damage (Bauerlein and McWhirter, 2014).The spill site was located a little more than 1.6 km (1 mile) upstream from the intake of a municipal water treatment facility operated by West Virginia American Water (WVAW), which serves a population of 300,000 across nine counties in central West Virginia (CDC, 2014a). In a matter of hours, the leaked MCHM made its way through the treatment facility and into the water of nearby homes and businesses, where its strong smell was noticed almost immediately. On the evening of the spill, WVAW concluded that its conventional treatment processes, which include carbon filters to remove a variety of contaminants from water, were not capable of fully removing the MCHM and a "Do Not Use" order was issued for all customers (WVAW, 2014a).With little information readily available regarding the potential human health effects of MCHM, the U.S. Centers for Disease Control and Prevention (CDC) quickly issued an advisory ruling that set a maximum screening level of 1 ppm for safe drinking water (CDC, 2014a). Based on this recommendation, the "Do Not Use" order remained in effect for a total of eight days, until Jan. 17, when the WVAW distribution water was confirmed to have MCHM concentrations below the approved level (WVAW, 2014a). However, due to the pungent odor of the chemical, its presence was still recognizable in the WVAW facility and in consumers’ tap water after the order was lifted (Manuel, 2014). Recent studies have shown that the chemical can be detected in water at sub-ppb concentrations, a fact that undoubtedly added to growing public concern (Rosen et al., 2014; Gallagher et al., 2014). In response to numerous complaints and demands, WVAW continued flushing the treatment facility and pipes until Feb. 25 when MCHM levels were measured below 2 ppb (WVAW, 2014b), and eventually replaced the affected filter media (WVAW, 2014c)."

Jan 1, 2014

By M. E. Hinkle

Concentrations of He, CO2, and O2 in soil gases were measured regularly for more than a year at a site near Golden, Colorado. Samples were collected from a hollow probe at 0.75-m depth and from a plastic hemisphere on the ground surface. Soil temperature, air temperature, percent humidity, And barometric pressure were also measured. Soil moisture was measured only indirectly as amount of rain or snowfall. Higher concentrations of CO2 in both the 0.75-m and surface samples correlated with higher soil and air temperatures, which suggests that CO2 was produced by bacteria. Lower concentrations of helium in both the 0.75-m and surface samples correlated with higher soil and air temperatures. Rain and snowfall appear to affect helium concentrations. Carbon dioxide concentrations were lowest when snow lay on the ground for extended periods of time. No correlation was seen between barometric pressure or percent humidity and concentrations of He, CO2, or O2 at 0.75-m depth or at the ground surface. No correlation, either positive or negative, was seen between concentrations of CO2 and O2.

Jan 1, 1988

By Derrick Chambers, George Kevin Chapin, M. Shawn Boltz

Seismic monitoring is one of the few noninvasive technologies with the potential to provide sub-surface geomechanical information to operators of large open-pit mines. Although passive seismic data has been used to refine emerging failure geometries and provide advance indication of surface deformations in the literature, doing so reliably in an operational context is much more difficult. This is due in part to difficulties in estimating and interpreting source locations and parameters in complex, low-stress open-pit environments. Additionally, the high costs associated with implementing, operating, and maintaining deep borehole seismic networks, which are most commonly used to monitor large open pits, can be difficult to justify, especially if monitoring benefits are not readily apparent. In this study, we explore the use of a near-surface nodal seismic deployment, which is commonly used in oil and gas exploration, for monitoring open-pit mining-related seismicity on a short-term basis. A deployment of 18 geophones was conducted on the surface in and around the Bingham Canyon Mine, a large open-pit mine near Salt Lake City, Utah, USA, where we find the small seismic array can detect and locate a variety of mining-related seismic sources, even with an extremely simplified velocity model. We outline the process of creating an idealized velocity model, developing a local magnitude scale, and interpreting the observed seismicity. Of note, we analyze a sequence of mining-induced events associated with a known structure on the south pit wall. We conclude with discussion on how surface-based deployments may be used to augment, or in some cases supplant, borehole seismic networks at large open-pit mines depending on monitoring requirements and objectives.

Apr 26, 2022

Production In 1993, it was estimated that United States mine production of barite increased 24%. Barite consumption, either sold or used by grinding plants, increased by 39% and imports increased 4%, according to the US Bureau of Mines (USBM). Nevada continued to be the leading producer of barite with 80% of the total, followed by Georgia. It is estimated that 83% of the domestically mined barite was used as a weighting agent in drilling fluids. The remaining 17% was used in barium chemicals, glass or as a filler. Most of the production from Missouri, Georgia and Tennessee was used in the non-oilfield sector. Prices The value of domestically produced barite, f.o.b. mine, decreased 1%, according to the USBM. The declared value c.i.f. US port of all imported crude barite during 1993 decreased from $40.09/t ($36.37/st) in 1992 to $37.72/t ($34.22/st). Uses Of the total barite used by grinding plants and chemical manufacturers, it is estimated that 90% was used in drilling fluids and 10% in the non-oilfield sector. This included barium chemicals, fillers in paper, plastics, brake shoes and glass. The tonnage consumed in the drilling fluids market increased due to the higher average rig count during 1993. The average number of rotary rigs operating in the United States was 754, 5% greater than the 1992 average of 717. Imports Crude barite imports in 1993 were 443 kt (488,000 st) greater than 1992, representing an increase of 137%. Imports accounted for 67% of the barite consumed (apparent) in the United States.

Jan 1, 1994

By L. Larrimore

Electric utilities depend heavily on coal as a major fuel source for power generation, annually producing more than 85 million ton&apos;> of ash, boiler slag and FGD (flue gas desulfurization -"scrubber") materials as by-products. Utilities and others who burn coal have traditionally disposed of these by-products in ponds or landfills. However, in the last 10-15 years there has been a greatly increased emphasis on beneficial utilization of these materials by the producers themselves as well as by customers who purchase the by-products. Regulatory, cost and technical performance issues currently impact the use of coal ash and other coal combustion by-products (CCB).

Jan 1, 1997

By Ellen S. Forbus

Reduction bleaching is used to improve the brightness and color of the kaolin pigments sold to the paper and speciality industries. The bleach re¬duces the iron oxide associated with kaolin deposits to a colorless form by the following reaction: Na2S2O42+ 6Fe+3 + 4 H2O -> 2 NaHSO4 + 6Fe+2 + 6H+ (Conley et al., 1964). At present, sodium hydrosulfite is used by the kaolin industry as the reductive bleach. It is often purchased commercially as a liquid solution and added into an acidified slurry. Before the use of commercial sodium hydrosulfite, kaolin plants manufactured zinc hydrosulfite on site by adding zinc dust to sulfurous acid made by passing SO2 gas into water. This process was abandoned in the 1970s due to environmental concerns about zinc in waste waters. In the 1970s, Engelhard patented a process that made sodium hydrosulfate from an iron hydrosulfate (Tiethof, 1978). Difficulties with separating the iron hydroxide byproduct from the bleach and a decrease in the cost of commercial bleach caused the project to be abandoned.

Jan 1, 1993

By Chen L. Lin, Luis R. M. Bittencourt, Jan D. Miller

Recently research efforts have been made to obtain a high-purity gibbsite concentrate, suitable for first-class alumina refractories, from a Brazilian bauxite ore containing gibbsite (50%), quartz (35%),and kaolinite (15%). Detailed polished-section microprobe analysis was used to describe the liberation characteristics of the ore. Experimental results suggest that the kaolinite liberation characteristics can be described by King&apos;s liberation model and that only about 11% of the kaolinite is expected to be liberated at a particle size of 75 µ. Bench-scale experiments for the flotation of gibbsite/kaolinite from quartz using alkyl sulfates as collectors were particularly successful at pH 2, and under appropriate conditions a concentrate containing 93.0% A1 0 (calcined basis) was obtained 2 3 at a gibbsite recovery of about 96%. Subsequently, the more difficult separation of kaolinite from gibbsite was accomplished by kaolinite flotation from the alumina concentrate with a quaternary ammonium salt at pH 6 to produce a high-purity gibbsite product, 97.4% A12O3 (calcined basis), at an overall gibbsite recovery from the bauxite flotation feed of about 90%.

Jan 1, 1990

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

The rare earth element (REE) industry has sought to develop ore deposits where geologic processes have produced mineralized zones with commercially attractive concentrations. These deposits are extremely uncommon, particularly in the United States. Given the criticality of these materials and the need for a sustainable domestic supply, the current research seeks to leverage the generation and treatment of acid mine drainage (AMD) as an autogenous process that can lead to concentrated REE resources. 

By R. Benito

The publication of the Lerchs Grossmann paper in 1965 outlining a threedimensional graph algorithm for ultimate pit definition set the standard for the mining industry regarding pit optimization. Although the algorithm provides a solution from a static standpoint (i.e., assumes instantaneous mining), it is widely used for commercial packages to generate ultimate pit limits and intermediate phases. However, the solutions delivered are presented in canned reports lacking connection to the original data, which prevents further data analysis and extended reporting. The approach presented in this paper attempts to overcome such barriers by performing openpit optimization through databases. An adaptation of the Lerchs Grossmann graph algorithm is used to generate nodes, arcs and tree structures in customized tables to determine the maximum closure of a graph.

Nov 1, 2013

By K. L. Boyd

"Can the ever-increasing tonnages of ore and waste being mined today be accommodated simply by using bigger and better crushers? This paper reviews the latest primary crushing and large cone crusher designs. It highlights how—in addition to using the larger crushers now available—maximizing the utilization percentages in each of the four stages of the rock size reduction circuit will assist in meeting the larger production requirements of existing and new mining operations. Its goal is to help consultants and operators select the optimal equipment and custom-designed items in the material handling flowsheet from the mine to the mill, maximizing operating hours per year. INTRODUCTION Are larger crushers the answer to meeting the demands of existing or new mining projects for increased tonnage? Boyd (2002) predicted that larger crushers for primary and fine crushing would be beneficial and contribute to the further development of mineral processing. Larger crushers for primary and fine crushing applications are now available. The rock size reduction process from the mine to the selected milling process facility has not changed since man first broke a rock to get at the interesting mineralization within. The rock size reduction process circuit from the mine to the mill can be summarized in four stages: • Stage 1: Mining (rock breakage and fragmentation) • Stage 2: Pre-screening (scalping) • Stage 3: Primary crushing • Stage 4: Fine crushing (secondary, tertiary and quaternary) Plant throughput and ore delivery schedule will form the basis for flowsheet design and equipment selection. Once the project design criteria and the mine plan have been established, the circuit’s utilization percentage (percentage of hours when the circuit is being utilized) can be optimized for each of the four stages. The mining and process departments are the key stakeholders in the selection of the final comminution circuit, and both departments should be familiar with and contribute to the design of the circuit. This paper focuses on the four stages of a rock size reduction circuit from the mine to the mill, equipment selection, various ore and waste handling flowsheets, and improvements in crusher station design, all with the purpose of maximizing availability and plant utilization percentages. What is a large tonnage? From 1907 to 1914, the American Panama Canal excavated 300 million tonnes of material in 7 years (History of the Panama Canal, Wikipedia). Today’s large mining operations can move the same material in 10 months, using large crushers or multiple crushers for ore processing and large crushers and a mixture of truck haulage and conveyors for handling the large waste tonnages. Some examples include:"

Jan 1, 2017

By Arash Dahi Taleghani, Pooyan Asadollahi

Slurry walls, also known as diaphragm walls, are commonly used as temporary and/ or permanent support of excavation for construction of shafts in soft ground. Through case history, this paper demonstrates economical benefits of disregarding long-term structural contribution of the slurry walls particularly in severe environmental condition. In addition, for temporary slurry wall shaft systems, possibility of using steel fiber, synthetic fiber or additives in lieu of temperature/shrinkage reinforcement is discussed with detailed analysis. Finally, the paper will be concluded by introducing unreinforced slurry wall shaft system using newly developed/patented concrete additive.

Jun 13, 2021

By Robert G. Woolery

Union Carbide_ began looking seriously at heap leaching in 1971. At that time some 1.6 million tons of mineral averaging 0.040% U308 were stockpiled at various sites around the Gas Hills, Wyoming, uranium facility. Several alternatives for economically exploiting these reserves were considered and heap leaching seemed the most attractive. At the time, Western Nuclear Inc. was operating a heap leach project nearby in which the low-grade ore was leached with sulfuric acid, the product liquor treated in an on-site solvent extraction circuit, and the stripped product liquor re-acidified and recycled. They were most generous in allowing us to visit their site, answering our questions, and were helpful in discussing the problems associated with heap leaching. They confirmed our belief that, it was possible to operate a heap leach profitably on material too low grade for. conventional milling. Based largely on what we had learned from Western Nuclear&apos;s experience, a program was set up involving a laboratory study to determine the characteristics of the mineral stockpiles as related to heap leaching and to conduct a pilot heap leach adjoining our Gas Hills mill. Basically, the pilot heap construction and leach procedure were similar to those described in the literature(1,2) with certain modifications to permit detailed monitoring of the operation. In May, &apos;1972, the decision was made to construct a test heap. The UCC plant at Gas Hills, Wyoming was selected as the most appropriate site for the follow¬ing reasons:

Jan 1, 1977