Search Documents

By H. Verakis, M. A. Hockenberry, A. C. Smith, J. H. Rowland III

Four different types of fire suppression systems were evaluated in large-scale fire experiments to study the effect of air velocity on their effectiveness in extinguishing conveyor belt fires. The four different types of suppression system were water sprinkler, deluge-type water spray and two different dry chemical fire suppression systems. The large-scale fire tests were conducted with 1.8-m- (72-in.)-wide fire-resistant rubber belt that met the Mine Safety and Health Administration flame resistant requirement specified in Title 30, Code of Federal Regulations, Part 18, section 18.65 (also known as the 2G Flame Test). Each fire suppression system was tested at air velocities of 152 - 168 m (500–550 ft) per minute (mpm) and 411 - 457 mpm (1,350 - 1,500 fpm). Two tests were conducted at both air velocities for each fire suppression system. Both of the water-based fire suppression systems were able to suppress the fire to the point that a miner could extinguish it with a fire extinguisher. However, the amount of water needed to suppress the fire to the point where a miner could walk up to and extinguish any smoldering belting was greater than the current MSHA regulations required. MSHA regulations only require 10 minutes of water supply for a suppression system. In the test setup, neither of these systems would have suppressed the fire had the water been turned off to the system after 10 minutes. The dry chemical suppression systems produced mixed results. Dry chemical suppression system A did not suppress the conveyor belt fire at either air velocity. Dry chemical system B suppressed the fire at 152 mpm (500 fpm) air velocity, but produced mixed results at the higher air velocity. Details are presented on the large-scale fire test setup, arrangement of the fire suppression systems and conclusions regarding the effect of air velocity on fire suppression system design and performance.

Jan 1, 2010

By Frank M. Howell

Creede, one of the younger major mining camps in Colorado, grew spectacularly to a town of eight or ten thousand people in the early 1890's following discovery of rich ore in the Amethyst and Last Chance mines. Gross metal production in gold, silver, lead, copper and zinc rose to a maximum of four million dollars a year in 1893. Annual production dropped to much lower figures and ranged between one hundred and five hundred thousand dollars per year during the period from 1914 to 1940. Production reached a gross of eight hundred thousand to one million dollars per year by the mid-1950's. In the years 1953 to 1957, Steven and Ratté conducted geologic investigations which were carried on as part of a cooperative program of the U. S. Geological Survey and the Colorado Metal Mining Fund Board. In a preliminary report on the Creede District, Steven and Ratté suggested that the Bulldog Mountain Fault Zone appeared to be a favorable structure to prospect. On the basis of that recommendation, augmented by independent work done by Manning W. Cox, the property was acquired, transferred to Bulldog Mountain, Inc. and financed by an O. M. E. loan. Late in 1963 Homestake Mining Company, under a Lease and Option Agreement, backed the venture by furnishing additional funds plus management.

Jan 1, 1969

By S. Lu

The particle-bubble attachment and the rupture of formed aggregates in flotation cell were investigated in terms of turbulent regime. It was found that the particle-bubble collision rate is closely correlated to the energy barrier between particles and bubbles, and no adhesion takes place for the hydrophilic particle-bubble system due to the introduced ?capture efficiency? f(a) being zero. The values of an especially defined Weber number, i.e. the ratios of turbulent stress to aggregate strength in the inertial subrange of turbulence were estimated, the results showed that the detachment of a particle from a bubble involved in an aggregate is mainly caused by the turbulent stress only in the impeller zone, no bubble splitting occurs both in the impeller zone and in the bulk zone.

Jan 1, 1993

By Sean Peterfreund, Grant Finn, Ty Jahn

For urban underground development involving tieback anchors for excavation support, authorities having jurisdiction typically require tiebacks to be de-tensioned before project completion. This paper updates “A Proactive Approach to Tieback Anchor De-tensioning” (by Peterfreund and Finn, published in the 2017 RETC Proceedings), which discussed a new method employed in a cut-and-cover transit station project. Since publication of that paper, 237 tiebacks were successfully and rapidly detensioned from using a small-diameter drill to cut strands from the surface. To the authors’ knowledge, this was the first intentional large-scale use of a drilling method for this purpose.

Jun 13, 2023

By Louis M. Schlesinger, Joel F. Hutwelker

A pilot plant was constructed to attrition scrub and deslime North Carolina phosphate ore. A 15.2 cm (6 in.) diameter pilot-scale Linatex Hydrosizer was used for desliming. Four tests were run at a throughput of 2.9 t/hr/m2 (0.30 ton/hr/f t2) and a teeter bed density of 1.12-1.13 g/cm3. The teeter water flow rate was varied to create an upflow velocity ranging from 0.25-0.47 cm/s. (This latter value is equal to the terminal settling velocity of a 200 mesh (74 micron) particle having a density of 2.7 g/cm3.) The recovery of +200 mesh oversize to the sizer underflow was 95%-96%, regardless of the teeter flow rate. The recovery of -200 mesh undersize to the sizer overflow increased from about 90% at 0.25 cm/sec to 100% at 0.47 cm/sec. A metallurgical balance that was conducted for one of the tests showed that less than 2% of the phosphatic value was lost to the overflow. A fifth test was run using an upflow velocity of 0.47 cm/sec; however, the teeter bed density was maintained at 1.05 cm/sec. This change had the effect of reducing the cut point (d50), while maintaining complete slime removal.

Jan 1, 1993

By T. A. de Almeida, M. de Paiva Bueno, M. Powell

The mining industry is one of the foundations of modern society, providing not only the raw materials needed to maintain a contemporary lifestyle, but also serving as a basis for the development of future technologies. From the most basic components of an appliance to the materials needed to design an electric car or a space rocket, each raw material has gone through a painstaking procedure of extraction and processing, and ways to make this process more efficient will be of great help to meet an ever-increasing demand for minerals. One of the biggest challenges when extracting mineral resources is to measure the variability of the mineral body prior to processing. Comminution is the most power-demanding stage, and the lack of geometallurgical testing, often for financial reasons, may result in an inefficient operation. The Geopyörä Rock Breakage test was developed with the objective of making mineral variability data more accessible by providing both standard comminution parameters and rock mechanical properties at low cost, and with a modest sample size, allowing a larger number of samples to be tested to reduce uncertainties and assure productivity. The objective of this paper is to present the results of an extensive validation of this new rock breakage method against two of the main tests currently in use, namely the SMC® and Bond ball mill work index tests. More than 100 samples have been tested and the results compared, showing that the new method can accurately estimate the parameters of the traditional tests. This confirms that the new test is a reliable tool for comminution and geometallurgical tests.

Feb 1, 2023

By Corey Vaughan

Unplanned shutdowns from abrasive wear part failure in crushers, chutes, and slurry pipe assets can cost millions in lost production and reactive maintenance. 2Censor patented sensor technology enables real time abrasive wear monitoring of mineral processing equipment, turning passive assets into smart, data driven components. Wireless sensors embedded in liners and pipework transmit wear data live to operators, allowing for predictive maintenance, safer scheduling, and optimized asset life. This paper will present global case studies showing reductions in downtime, increased throughput, and improved maintenance accuracy. The system is ready to retrofit, neutral to original equipment manufacturers, and proven across more than twelve countries in abrasive wear liners and slurry pipe applications.

Feb 22, 2026

By W. C. Lacy

It is the responsibility of educators to look ahead and prepare young engineers and scientists to cope with industrial and social problems of the future. We are faced with a review of history as well as prophesy of the future. The mining industry exists in a "bubble" with little interaction or communication with the outside. This isolation must be broken down if the industry is to survive in the U.S. and Canada. The ability to communicate with the general public and public officials is essential. Many changes are occurring that will require readjustments in technology and staffing. Aging population will result in raising retirement and increasing available workforce. This may force shorter working weeks to supply additional jobs. Environmental concerns will likely direct more attention not only to these concerns during mining, but to planning for post-mining land usage. Retraining and up-dating educational programs are required to cope with these changes.

Jan 1, 1994

By R. Halatchev

This paper treats the spatial aspect of mine sequence optimization, revealing it in the context of determining the optimum number of cutbacks of an openpit mine. Cutback mining is currently a dominant method in the mining of base and precious metals. It is based on a pseudo-economic discretization of the pit space using advanced pit design algorithms. The result of implementing such an approach of pit design is the generation of pit shells, which need to be grouped into an optimum number of cutbacks to maximize project value. In this paper, the development of a mathematical solution of this problem using combinatorial analysis is presented. The solution provides a multivariate investigation of the optimum mine sequence with the implementation of a method for production scheduling optimization that uses Net Present Value (NPV) as a criterion for assessing the economic efficiency of mine sequencing. A case study using the conditions of a hypothetical openpit gold mine is provided to illustrate the applicability of the approach. The results obtained reveal the complex nature of NPV variation as a function of the cutback geometry.

Jan 1, 2015

By K. A. Natarajan, Abha Kumari

"The effect of applied DC potentials on the bioleaching of a chalcopyrite concentrate in the presence of Acidithiobacillus ferrooxidans is discussed. Copper dissolution was the highest at an applied potential of +600mV (SCE), while all the dissolved copper got cathodically deposited at a negative potential of -600mV (SCE). Electrobioleaching at an applied potential of +600mV (SCE) was established at different pulp densities as a function of time. The effect of applied potentials and electrolytic currents on the activity and growth of bacterial cells was assessed. Preadaptation of bacterial cells to the concentrate slurry and electrolytic growth conditions significantly enhanced copper dissolution. Electrochemical and biochemical mechanisms involved in electrobioleaching are illustrated with respect to oxidative dissolution and biocatalysis of anodic oxidation. IntroductionIn recent years, the bioleaching of low-grade chalcopyrite ores as well as their flotation concentrates has been receiving increased attention. Use of mesophilic bacteria such as Acidithiobacillus ferrooxidans in the bioleaching of chalcopyrite does not yield desirable copper extraction rates due to its easy passivation.Bioleaching of chalcopyrite using A. ferrooxidans has been reported to be very inefficient, and use of thermophilic bacteria at higher temperatures is recommended to improve its bioleaching rates. Bioleaching under imposed applied DC potentials or currents has been shown to enhance not only bioleaching kinetics but also to confer selectivity in mineral dissolution (Abhakumari, 1996; Chirpa Selvi and Natarajan, 1998; Natarajan, 1992a, b,c). Electrochemical principles governing electrobioleaching have been earlier illustrated (Jyothi et.al, 1989). The role of applied potentials on the activity and growth of A. ferrooxidans has also been studied (Natarajan, 1992b). Also, the electrochemical aspects of bioleaching of several sulfide minerals when present alone or in binary and ternary combinations have been reported (Jyothi et al., 1989). The electroleaching of copper-nickel concentrate (Natarajan et al., 1985) and electrobioleaching of sphalerite concentrates have already been studied (Selvi et al.,1998). However, it is possible to enhance the bioleaching rate of chalcopyrite in the presence of A. ferrooxidans under galvanic conditions in the presence of nobler minerals such as pyrite (Jyothi et al.,1989). Also, dissolution of chalcopyrite can be significantly enhanced under applied potential conditions. Ali Ahmadi and his coworkers recently studied the electrochemical bioleaching of chalcopyrite concentrates using moderate thermophiles (Ahmadi et al., 2010, 2011)."

Jan 1, 2015

"Mining of ore bodies that are located at great depths enforces long distances to move the excavated rock masses to the surface. The excavated rock mass contains not only ore that can be economically extracted from the face but also waste, which is usually discarded several steps further downstream in the process. As a result, a large amount of rock is transported to the surface, influencing the costs at which the ore is produced. Reducing the amount of waste rock being transported to the surface by introducing a near-to-face sorting plant would improve the in many cases strained transport system in the deep mine. In this study, one of Boliden’s cut-and-fill mines was analysed with respect to the challenges related to rock transportation and increasing mining depth. The study aims to evaluate the potential use of a new near-to-face sorting system in the operating underground mine. Discrete event simulation was used to study and analyse the rock transportation system with and without the near-to-face sorting plant. The paper shows how the underground rock transportation system and the production were influenced when the near-to-face sorting equipment was added into the current system. INTRODUCTION The locations of waste rejection in the mining processes and the cost of removing waste from the system compared with the cost and energy necessary for further comminution are important parts in the material handling system (Bowman and Bearman, 2014). In an underground mine, longer material transportation distances generate the need for further investment in the mobile fleet and ancillary equipment in order to reduce the waste from the material handling as early as possible. One of the ways of reducing the waste (coarse particle size) in material handling is by use of pre-concentration. The benefits of pre-concentration are well known (Schena et al. 1990; Feasby, 1995; Peters et al. 1999; Klein et al. 2002), as well as the factors governing the feasibility of underground pre-concentration (Peters et al., 1999) and the mining integration issues (Klein et al. 2003). In the Onaping Depth orebody in Sudbury, Ontario the study of implementing the pre-concentration resulted in increased capital costs of 6% and a reduction in the operating costs of between 20-40% (Bamber et al, 2004). In this paper, the effects on the production and the transportation system of implementing underground pre-concentration by means of a near-to-face ore sorting plant in the Kristineberg mine are modeled and analyzed using the AutoMod tool. This tool is based on discrete event simulation (DES) (Banks, 2004), allowing high flexibility in customization and enabling the user to view the production of the system before ore sorting plant integration. The sorting plant selected in the simulation is built from modules. The material is fed by conveyor and goes through the comminution, classification, sorting and service processes after which the waste is redirected to backfill headings via trucks. The system mechanically ejects the particles from the feed stream on the basis of the information obtained from both the XRT sensor’s signal and 3D laser scanner based on both density and rate of refraction of light within a particular mineral. The sorting plant could pre-concentrate the metal ore up to 300 mm size. The plant requires little auxiliary infrastructure, is easily modularized for underground installation and can be easily relocated to different areas."

Jan 1, 2016

By D. Tao

Reverse cationic flotation is the most widely utilized flotation method for concentrating iron ore. In this process, quartz is often floated with ether amines (R?(OCH2)3?NH2) partially neutralized with acetic acid. However, it is well known that the cationic flotation of quartz does not work well if a certain amount of slime is present in the ore slurry. To improve flotation performance, starch is often added to the flotation feed to selectively flocculate and depress the iron minerals and sodium silicate is used to disperse the silica gangue. The present study was conducted to improve the efficiency of iron ore flotation by the use of a new type of depressant for clay and iron minerals, Georgia Pacific (GP) clay binder. The GP clay binder minimizes slime adsorption on quartz and hematite particles by agglomerating clay particles to reduce their surface area. It also helps depress hematite flotation due to its unique chelating action on iron ions. The results from this study show that the GP clay binder is an effective depressant in iron ore flotation. When it was used as a substitute for corn starch, it increased concentrate grade from 60.78% to 67.67% and increased iron recovery from 71.96% to 72.90%. The combined use of GP clay binder with corn starch produced even better flotation performance, increasing iron recovery to 78.15%, while the concentrate grade remained stable at 67.08%. Keywords: Georgia Pacific clay binder, Iron ore flotation, Flotation efficiency

Jan 1, 2010

By N. H. Coates

The Bureau of Mines designed, constructed, and operated an 18-inch- diameter, fluidized-bed combustor for highly caking coals to evaluate the method for possible application to power generation. In initial tests, combustion was carried on successfully, with carbon losses as low as 0.8 percent. Coal ash was not satisfactory as a bed material, but mullite proved to be acceptable. Overall heat-transfer coefficients from the bed (-20 + 50 mesh mullite) to a water-cooled tube were about 75 Btu/hr-ft2- °F.

Jan 1, 1970

By A. Podlesny, E. N. Rubinstein, J. J. Sammarco, B. Demich

Roof bolting typically follows the extraction of a commodity to help keep the roof from collapsing. During 2004 to 2013, roof bolter operators had the highest number of machinery-related injuries, accounting for 64.7 percent, at underground coal mines. This paper analyzes U.S. roof bolter fatal and nonfatal lost-time injury data at underground work locations for all commodities from 2004 through 2013 and determines risk indices for six roof bolting tasks. For fatal and nonfatal incidences combined, the roof bolting tasks in order of the highest to lowest risk index were bolting, handling of materials, setting the temporary roof support (TRS), drilling, tramming, and traversing. For fatalities, the roof bolting tasks in order of the highest to lowest risk index were handling of materials, setting the TRS, bolting, drilling, traversing, and tramming. Age was found to be a significant factor. Severity of injury, indicated by days lost, was found to increase with increasing age as well as with increasing experience, largely due to the confounding of age and experience. The operation of the roof bolting machine used in underground mining should be a research priority given the high frequency and severity of incidents. The results also suggest that temporal factors may exist, so additional research is warranted to better understand these factors and potentially develop interventions. This research provides a datadriven foundation from which future research can be conducted for safety interventions to reduce the frequency and severity of incidences involving the roof bolter activities of bolting, handling of materials, and setting the TRS.

Jan 1, 2016

By S. Tuylu, D. Adiguzel, A. Bascetin

"In recent years the fact that mining tailings cause serious environmental problems resulted in increasing number of studies about their disposal, storage and usability in various areas. Therefore the new studies about using the tailings for some purposes such as using in shotcrete or producing concrete have been increasing recently. The study is focused on applicability of tailings for producing shotcrete. Under this scope it is considered that mining tailings can bring many advantages in case of that they are used instead of sand, silt or fine aggregate in shotcrete applications. Most important advantages can be listed as decreasing shotcrete cost, decreasing amount if mining tailings to be disposed and the contribution to be provided on sustainable production of sources. The main objective of this study is the investigation of using mine tailing instead of fine aggregate in shotcrete. In this study, 10 shotcrete designs in different proportions were formed, and properties of the mixtures were identified. Then, the experimental results were statistically analyzed, the effects of the amount of the tailing material used on shotcrete properties were presented, and empirical approaches that can be used for the estimation of these properties were developed. INTRODUCTION The disposal of high amount mine tailing on the surface is caused a lot of problems in terms of environmental impact. Unfortunately, it is known that classic disposal techniques such as tailing dam cannot provide a solution these problems. The tailing dams which are usually used in the disposal of mining tailings bring along many problems in terms of cost, environment, and human health. So mine tailings are used in different production such as shotcrete. This technique is becoming increasingly common during recent years. The usability of mine tailings in brick and concrete production instead of cement and fine aggregate has been studied by many studies [1-4]. This situation has been promising for the usability of tailings in shotcrete which is commonly used for ground support especially in tunnels. Shotcrete (sprayed concrete) is applied mainly for construction of tunnels, shafts, renovation works and strengthening of slopes. Main advantage of shotcrete is fast development of strength, which quickly ensures stability of strengthened structure [5]. Shotcrete can be defined as spraying the grout consisting of water, aggregate, cement and optional additive mixture on the desired surface with a compressed air. According to the definition of the American Concrete Institute (ACI), it is the spraying of sprayed grout or concrete on a surface at high speed with air pressure [6]. In recent years, the use of shotcrete for the support of underground excavations is decreased in the mining industry. The design of shotcrete support for underground excavations is a very imprecise process. Strength and pumpability properties of shotcrete are very significant for determining suitable shotcrete design. Flow characteristics of the shotcrete must be determined for pumpability and fluidity of the material."

Jan 1, 2017

By Vincent T. Ricca

Acid mine drainage is a serious water pollution problem, for its contaminants will eventually effect the quality of the receiving streams. According to the Appalachian Regional Commission (1969)1, 10, 500 miles of streams have been polluted by mine drainage, and 70 percent of this acid pollution is accounted for by underground mines. Due to the severe damage to aquatic life, to recreational and industrial use, and to domestic water supply, more stringent mining and anti-pollution laws have been legislated and coal mine operators are required to treat the mine water discharges to meet the minimum standards. For years now, abatement and treatment methods have been extensively studied. Progress reports presented in the Fourth Symposium on Coal Mine Drainage Research, 1972 1 suggest that a thorough investigation and understanding of the basin discharge is necessary in order to cope with the mine drainage problem. The extent of mine water discharge contamination can be considered as a function of the basin streamflow and acid generation load.' A conservative treatment cost estimation these days is $0.40 per 1, 000 gallons for water with 100 ppm iron, 500 ppm acidity. These figures need not include collection and pumping costs nor the cost of dispersing of chemical waste by-products. To achieve optimal abatement and treatment of mine drainage, predictions of the quantity and quality of mine water discharges are needed. Basin discharge is a continuous process and it can be considered as a. macro-system. This system can be subdivided into micro-systems to describe the various mine discharge .types in the basin. The mining activities could produce acid water discharges from deep mines, stripmines, or associated gob piles. A total study entitled ?Resource Allocation to Optimize Mining Pollution Abatement Programs?* will consider all of these sources. However, this paper will discuss only one micro-system, the drift (deep) mine type. We will look at a single mine and its watershed. The total research project considers a multiple mining complex in an extensive stream basin.

Jan 1, 1973

By Jon A. Hummer, Aleksandar D. Bugarski, Shawn Vanderslice, Teresa Barone

Reducing the contribution of heavy- and light-duty diesel-powered equipment to concentrations of aerosols and gases is essential to industry’s efforts to improve air quality in underground mining operations. The results of this study demonstrated a potential of control strategies based on retrofitting existing power packages with diesel oxidation catalyst (DOC) and diesel particulate filter (DPF) systems and repowering existing systems with advanced power packages to reduce contributions of diesel-powered vehicles to concentrations of diesel aerosols and criteria gases in underground mines. The implementation of viable exhaust aftertreatment systems and advanced diesel power packages could be instrumental in the underground mining industry securing a clean, economical and dependable source of power for mobile equipment.

By K. D. Luxbacher, E. C. Jong

Perfluoromethylcyclohexane (PMCH), a member of the perfluorocarbon tracer group of compounds, has been shown to be a viable supplement to the widely used tracer gas sulfur hexafluoride (SF6). This viability stems from the fact that PMCH can be used concurrently with SF6 while maintaining adequate chromatographic separation and comparable sensitivity during analysis. However, the release of PMCH in an underground mine ventilation system is challenging due to its physical characteristics. While SF6 exists as a gas at room temperature and pressure and can be accurately released by a variety of means, PMCH exists as a volatile liquid at room temperature and pressure, preventing it from being deployed in a similar manner. One method to release PMCH is to use a permeation plug passive release vessel (PPRV), which allows for the controlled release of the gas. This paper presents the results of a study evaluating various preparation techniques, plug thicknesses and plug materials of an aluminumvessel PMCH release source, so that a source appropriate for the mine scale may be developed.

Jan 1, 2015

By Angelina Anani, Nilufer K. B. Akbulut, Sefiu O. Adewuyi

Crucial information about safety, design, and operation can be utilized in underground mines from ground movement data. Communicating the information and exploring new findings can be a challenge in a decade where there is an ever-increasing volume and velocity of data due to advancements in mining technologies. This challenge escalates for geotechnical data as it is multidimensional, depending on the space and the rate it takes place. To tackle this challenge, geotechnical engineers should focus on utilizing simple yet compelling visualization of rock mass data in 3D. Competent visualizations of ground conditions as a Trigger Action and Response Plan (TARP) could ease the communication of safety concerns and the exploration of rock mass displacement and strain surrounding an opening at an underground mine. Therefore, this study focuses on using scientific visualization methods by rendering geotechnical data over the surface of a 3D mesh model to display TARP levels. The study is conducted at the San Xavier (SX) Underground Mine Laboratory’s East decline. The project aims to produce visualizations that optimize the use of geotechnical data in near-real-time.

Feb 1, 2025

By Peter Hornby, Maurice Craig, Franklin G. Horowitz, Don Bone

We have developed a high-performance, flexible scheme for interpolating multi-dimensional data. The technique can reproduce exactly the results obtained, for example, from Ordinary Kriging and related techniques in 3D, or from Thin-Plate Splines (Briggs' minimum-cuwature algorithm) in 2D. Moreover, com- pared to traditional implementations of these algorithms, our method enjoys large computational-cost savings. The new approach produces an interpolation that obeys a Partial Differential Equation (PDE). The PDE may arise from physically based arguments, but its form can vary widely. It might be specified only implicitly (as through a Model Variogram), or be nonlinear (although a performance penalty could then apply). While a formal equivalence between Kriging and Splines has been known for some time (Matheron, 1980), the present derivation, from radial basis functions, further illuminates this connection. Thus, for example, we can make explicit the PDEs that underlie some of the Model Variograms most often used in Geostatistics. Besides its practical utility, the work thereby ac- quires a theoretical interest.

Jan 1, 1996