Search Documents

By A. L. Williamson, G. Savci

Hydrologic assessments of existing and proposed waste rock stockpiles (WRS) are typically required for application of operating and closure permits at mine sites. The results of these assessments can be used to determine the applicability of the state groundwater permit program requirements to the operation and closure of these stockpiles. The objective of this hydrologic assessment was to ascertain whether or not the WRS at the Ajo Mine have a reasonable probability of discharging potential pollutants to the underlying aquifer under the operational mine conditions. The hydrologic assessment was performed based on an evaluation of climatic data, prediction of the net infiltration rate through the WRS and prediction of additional hydrologic factors such as the time required to deplete available moisture storage in WRS. The predicted net infiltration rates ranging from 0.13 inches/year (1.1x10-8 cm/s) to 0.24 inches/year (1.9x10-8 cm/s) are below the threshold value of less than 10-7 cm/s recommended by Hutchison and Ellison (1992) as being characteristic of conditions that produce no or negligible quantities of seepage. In addition, the total time required to deplete available moisture storage within the Ajo Mine WRS and for any potential seepage from the WRS to reach the underlying aquifer is estimated to range from 260 years to 1,950 years. Collectively, the climatological and geotechnical investigations and the hydrologic predictions demonstrate that the WRS at the Ajo Mine hydrologically do not have a reasonable probability of discharging pollutants to the underlying aquifer. As a result of this prediction, the stockpile will not be regulated under the state groundwater permit program and operational and reclamation requirements will be limited to managing surface water runoff.

Jan 1, 2002

By K. A. Grace

"An ore is a rock regardless of its rarity or value."* The application of geology does not cease with the discovery and delineation of a mineral resource, but continues in the calculation of the economic parameters that determine reserves. Reserve determination, reduced to essentials, is the determination of the cost of production of a mineral commodity from a resource. This cost comprises mining, processing, waste disposal, reclamation and marketing costs. Geological input is vital in the calculation of the individual cost parameters from mining to reclamation, and even has some impact on marketing. Geology thus has a critical role in the determination of reserves.

Jan 1, 1985

By L. Yuan

To reduce fire hazards from spontaneous combustion of coal in longwall gob areas, a series of computational fluid dynamics (CFD) simulations were conducted by National Institute for Occupational Safety and Health (NIOSH) to model the spontaneous heating of coal in longwall gob areas. The previous modeling results demonstrate that spontaneous heating of coal usually occurred behind the longwall shields and along the face with a bleeder ventilation system. Assuming a stationary longwall face, the spontaneous heating could turn to a spontaneous fire in several days for the most reactive coal under favorable conditions. When the longwall face advances, the spontaneous heating process will be significantly affected. In this study, the effect of longwall face advance on the spontaneous heating in the gob area is investigated using the CFD model developed in previous studies. One longwall panel with a bleeder ventilation system is simulated. The width of the panel is 300 m, while the length of the panel is changed between 1,000 to 2,000 m. The same permeability and porosity profiles are used for gobs with different lengths. The spontaneous heating first develops in the gob when the longwall face is stationary. Then, the face advances at a certain rate. The face advance is simulated as a series of discrete movements, and the effect of the face advance on the maximum temperature developed during the face stoppage is examined. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2009

By Samer Sadek, David I. Smith, Wai-shing Lee, Jeffrey L. Rice, Avelino Alonso

INTRODUCTION East Side Access (ESA) Contract CQ028 is located in the New York City Borough of Queens. The contract involves construction of a 230-meter (760-foot) long open-cut excavation with a permanent deck supporting Amtrak yard tracks over a semi-circular TBM launch wall on the east end, and the 36.5-meter (120-foot) long Northern Blvd. Crossing on the west end. The Northern Boulevard Crossing will be mined under an existing New York City Transit (NYCT) five-track subway tunnel; Northern Boulevard, a heavily traveled five-lane truck route; and an existing NYCT three-track elevated line; connecting to an existing open-cut shaft adjacent to the existing 63rd Street Tunnel bellmouth. When completed, Contract CQ028 will provide access for future Manhattan and Queens tunnel contracts. The footprint of the open-cut was determined by the geometric requirements of the future Plaza Interlocking facility to be constructed within in another future ESA contract. See Figure 1. This paper discusses design risk mitigations for the key elements of the contract, namely the Northern Blvd. Crossing and the semi-circular TBM Launch Wall. PROJECT OVERVIEW The Metropolitan Transportation Authority Capital Construction Company—East Side Access Project for the Long Island Rail Road will provide Long Island commuters with direct access to Manhattan’s East Side via a new rail line between the Harold Interlocking in Queens and Grand Central Terminal in Manhattan. The project connects the unused lower level of the existing tunnel under the East River at 63rd Street to new connecting tunnels in Queens and Manhattan. Contract CQ028 Scope and Construction Schedule This contract consists of the excavation of an open-cut from the east side of Northern Boulevard, through an existing MTA-owned rail yard and into the western limits of Amtrak’s Sunnyside Yard. The contract will connect to a completed open-cut

Jan 1, 2007

By Charles Merguerian

In medium- to high-grade metamorphic terrains such as found in New York City(NYC), rock mass texture and mineralogy are important factors in predicting TBM penetration destiny. Integration of data from over two decades of traditional field and tunnel mapping suggest that hard-rock TBM penetration in the NYC area depends upon textural, mineralogic, and structural control. The bedrock of NYC consists of many different lithologic units of varying age, composition, texture, and metamorphic grade including many varieties of intrusive rock. In addition, brittle faults of numerous orientations cut the polydeformed crystalline bedrock, producing zones of highly fractured and disturbed ground and high water inflows. Pre-bid compilation of published bedrock data, drill core analysis by geologists to establish lithologic and mineralogic trends, integrated surface geologic mapping along a proposed alignment, and targeted petrographic and geotechnical investigations to characterize the rock mass conditions together constitute an important prelude to successful subsurface bidding and tunneling. A carefully planned program of as-built geological mapping, structural analysis, fracture class mapping, and monitoring of machine performance data provide important information for adjusting to changed conditions. In complex terrains, a clear understanding of the structural geology of any proposed tunnel line is the simplest and most cost-effective method to mitigate losses encountered during TBM tunneling.

Jan 1, 2005

By John E. Tilton

The ability of companies and countries to mine copper and other mineral commodities competitively and in the process to generate new wealth depends on their mineral endowment. Chile, for example, produces and exports copper because it is well endowed with high-quality, low-cost deposits. This production creates wealth that benefits mining companies and their stockholders, the government, local communities, as well as copper consumers around the world. The widespread perception that mineral endowment must largely determine competitiveness, or what economists call comparative advantage, must be true at any particularly moment. Countries with abundant reserves must be competitive. This follows from the definition of reserves — the quantity of a mineral commodity found in discovered deposits that are profitable to exploit under current conditions. As a result, it is a tautology and not particularly interesting. The important question is what causes reserves to change over time, producing in the process new wealth and shifts in competitiveness?

Jan 1, 2003

By Francois E. Heuze

The mined geologic burial of high-level nuclear waste is how the favored option for disposal. The underground repositories must keep the waste away from the biosphere for very long times - several thousands to tens of thousands of years. Also, access must be maintained to the vaults for several tens of years, so that the waste can be retrieved, if necessary. Both the excavation of the underground chambers, and the radiogenic heating will disturb the rock mass. The overall rock mechanics problem is to understand and predict the processes associated with these perturbations, and their impact oh the isolation and containment of the waste (3)**. The specific rock. mechanics issues which have been identified for the three candidate hard rocks (basalt, granite, and tuff), are summarized in Table 1. The table also indicates the level of adequacy of our knowledge in the areas of the various issues. Such an evaluation is consistent with the general consensus of the rock mechanics profession, as explained in several key reports and publications (1 to 11). The main shortcomings of today's rock mechanics for waste repositories can be summarized as: ? lack of resolution for remote mapping of fractures in rock masses ? great difficulty in testing large volumes of rocks to determine their mechanical properties.

Jan 1, 1981

Overcasts are indispensible ventilation control devices to permit one airway to pass over another without mixing in room and pillar coal mining. The airflow distribution inside the overcast depends on its spe-cific configuration at which the flow enters into it. This study uses 3D numerical simulation to examine the pressure and velocity distributions inside an overcast. The effects of the overcast angle on the flow field are also examined. The flow is assumed to be turbulent and isothermal and the standard k-e model is utilized. Simulated results display flow separation and recirculation regions of different sizes occurring not only upstream and downstream from the overcast but also inside it. The results also show that the size of the recirculation regions in-creased with the increase in the angle before and after the overcast influencing significantly the flow field and pressure losses. The stream-lines are plotted to show the 3D structure of the flow field. The results from the simulation can guide overcast design commonly used in un-derground coal mines. Keywords: 3-D simulation, Overcast, Room and Pillar, Turbulence, Recirculation Region

Feb 27, 2013

While the United States and the rest of the world struggles with record-setting oil prices Canadian oil sands producers are ramping up production to meet demand for oil while also fighting against a host of negative images. In recent months, the price of oil has skyrocketed. Most of that oil comes from Saudi Arabia. In Alberta, Canada there are unconventional oil reserves that rival those in Saudi Arabia in the vast Canadian oil sands, sometimes called the tar sands. Proponents of the oil sands say that Alberta?s oil sands can be a secure source of oil and energy for the United States for many years to come. With new mining and drilling projects, the industry has said that it could quadruple its production to nearly 4 million bbl/day by 2020. Time magazine once called the oil sands, ?Canada?s greatest buried treasure that could satisfy the world?s demand for petroleum for the next century.? So why hasn?t the United States embraced this close, politically secure source of energy? Because, getting usable fuel from the oil sands can be a dirty business, say opponents. The oil sands are a combination of clay, sand, water and bitumen. It is a heavy, black, thick oil. Oil sands can be mined and processed to extract the oil-rich bitumen, which is then refined into oil. The bitumen cannot be pumped from the ground in its natural state. Instead, tar sand deposits are mined, usually using strip mining or openpit techniques, or the oil is extracted by underground heating with additional upgrading. These methods require a huge amount of energy and water and produce a large amount of carbon emissions. Environmental groups that have long spoken out against the oil sands projects got some political backing in the United States in June when a group of mayors from large U.S. cities spoke out against the oil sands, as did presumptive Democratic candidate for U.S. president Barack Obama?s senior energy advisor. During a convention of large-city mayors in Miami, FL, Alberta?s oil sands were singled out in a nonbinding resolution calling for national guidelines to track the lifecycle impact of different types of fossil fuels. The resolution urges cities not to use unconventional sources of energy with a large carbon footprint, such as liquid coal and oil shale and oil sands.

Jan 1, 2008

By S. Yerel

In a mineral processing plant, the determination of a preventive maintenance schedule is one of the most important maintenance policies. In this study, to determine the preventive maintenance schedule for the Emet Colemanite Mineral Processing Plant in Turkey, a mean quality control chart was constructed using the historical concentrate B2O3 grade data. The effect of preventive maintenance scheduling on B2O3 grades was monitored using the mean quality control chart. It was determined that recovery increased after each preventive maintenance scheduling. Close examination of the mean quality control charts indicated that there were three periods that showed different grade characteristics. These were identified as the period ?prior to preventive maintenance,? the period ?after preventive maintenance? and the period ?requiring preventive maintenance.? These periods were compared as two independent samples by using the Kolmogorov-Smirnov test. Application of this test for interpretation of the mean quality control chart enabled the authors to analyze the system effectively, and it showed that the preventive maintenance for this plant should be scheduled at four-month intervals.

Jan 1, 2007

By C. Dan Kealy

Recent antipollution legislation for the control of mine tailings and waste-water has required an increasing number of tailings ponds. Many of these new waste-retention ponds are being constructed in congested locations, or the older ponds have reached such a size that--if failure occurs--they pose a threat to human life and public property. Although the typical tailings-disposal embankment represents--to the casual-, observer or the economy-minded mine official--a rather ugly but benign and stable pile of waste, they are in fact an extremely sensitive structural mass, retained behind the frailest of dikes. Failure of the waste mass requires only a minor change in water retention or weather conditions, erosion or piping of the ground strata, shifts in load or slight earth tremors. When failures occur, the results can be disastrous. In the U.S., we have been fortunate that, so far, pond failures have not caused loss of life. Thus, failures in this country have attracted little public attention. Present tailings-pond construction methods used by the mining industry require the barest money investment, and little engineering effort. Unfortunately, this superficial approach may increase short-term profits, but the practice may be conducive to the construction of needlessly weak structures. In coming years many of these designs will probaly become corporate liabilities. A typical pond is portrayed in Figure IA. This particular pond in Arizona is 1 mile long and 3/4 mile wide. Illustrated in Figure lB is a representative pond in cross section. This paper in concerned with two basic features common to all tailings disposal: (1) location of the phreatic surface within a tailings-pond embankment because of its influence on embankment-slope stability, and (2) prediction of

Jan 1, 1971

By Shimi Tzobery, Jay Davenport, Raymond Henn, Sam Bandimere

Over the past several decades, the use of cement-based grouts using ultra fine cement as a replacement for portland cement has begun to gain acceptance as an alternative to chemical solution grouts used in permeation grouting. The amount of information currently available on grouts made with ultrafine cement is limited. The authors used a previously developed field testing program to perform additional tests to evaluate the permeation performance of portland and ultrafine cement-based grouts. For the first time, the 2003 testing program included an attempt to determine the 28 day compressive strength of the sand permeated by the grout.

Jan 1, 2005

By E. M. Frizzell

Development of mobile crusher systems for surface mining, allowing extension of continuous conveyor haulage systems into the pit, is traced from its introduction to the present. Variations in configurations are reviewed, and the compelling reasons for using mobile crusher systems are explored.

Jan 1, 1983

By R. J. Hickson

The Grasberg copper-gold deposit was discovered in Spring 1988, just one year prior to the planned closure of Freeport Indonesia's original Ertsberg open pit copper mine. In spite of Grasberg's remote location, 600m above the Ertsberg, atop a hitherto inaccessible mountain, Freeport-McMoRan brought their latest open pit mine into production in the last week of 1989, less than two years after discovery. This paper describes the start-up of the operation, highlighting synergies drawn from both the original Ertsberg experiences and the current Freeport Indonesia underground mines.

Jan 1, 1991

By Arthur M. Langer

Since the promulgation of the first Federal Asbestos Standard by the Occupational Safety and Health Administration in 1972, other federal agencies have modified the standard to better carry on their own unique missions. The instruments used to identify and measure asbestos, the sampling protocol, and the criteria used to define asbestos, have been modified to some degree. The Mine Safety and Health Administration regulates and controls asbestos dust in the mining and mineral commodity industries. However, crushed stone and processed ores contain mineral fragments that are frequently difficult to distinguish from asbestos. Mineral nomenclature, instruments for particle analysis, and sampling strategy must be accommodated to some degree to make asbestos control workable and meaningful. Precedent in other agencies has made consideration of these changes possible. Newly identified amphibole asbestos minerals have further complicated the agency?s regulatory charge. Changes in its Asbestos Standard are now being considered. Crushed taconite ore in the Eastern Mesabi highlights many of these issues. ©2008 Published by Elsevier Inc. Keywords: Amosite; Grunerite asbestos; Crocidolite; Riebeckite asbestos; Tremolite asbestos; Actinolite asbestos; Winchite asbestos; Richterite asbestos; Arfvedsonite asbestos; Fluor-edenite asbestos; Asbestos defects; Cleavage fragment; Mineral habit; Mesabi amphiboles

Jan 1, 2008

By T. L. Owen

Since 1993 Cyprus Amax has brought $2.5 billion dollars of greenfield and expansion projects into production, taking it from a mid-sized domestic minerals company into a major international minerals organization. The near simultaneous development of these multiple mineral projects in different locations around the world provided the opportunity for Cyprus Amax to develop a formal project management approach based, in large part, on an outsourcing philosophy. This formal project management system along with its outsourcing philosophy has served the growth agenda of Cyprus Amax extremely well. These preceding factors, coupled with the in-house retention of a core project group that fully understands the breadth of skills and abilities needed to undertake development of multiple large projects successfully, have been the cornerstone of Cyprus Amax’s project development success.

Jan 1, 2000

By M. Dobbins

The advent of the more efficient and effective rare-earth roll (RER) separator in the early 1980?s began a new era of dry magnetic separation. The RER units quickly became the separator of choice within the materials processing industry. Though RER separators are now commonplace throughout the world, only modest advancements have been made to the original design. This paper details recent, more significant, rare-earth magnetic separation developments. These developments maintain the best features of existing technology while minimizing shortcomings. The discussion includes discerning features that aid in better metallurgical performance. Also discussed are improved mechanical aspects that allow for both easier operation and maintenance. Performance details from various test programs are included.

Jan 1, 2009

By R. W. Carn, D. Vincent

Environmental Considerations With significant increases in bulk coal movements through terminals, operators are under constant social and political pressure to reduce or remove environmental pollution problems incidental to their operations. To meet these requirements, both equipment manufacturers and terminal designers are endeavoring to design equipment and systems with stringent environmental controls. The most challenging environmental problems facing coal terminal designers and developers are terminal siting restrictions, dust control, and noise abatement. Terminal Siting Finding a suitable site can be a difficult problem because of public concern over coal dust or the impact of a terminal on the surrounding community or natural habitat of the area. Often the only suitable flat land available for terminal development is on a tidal estuary or salt water marsh with great environmental value. In many cases a period of four to six years of full environmental and social assessment has been needed. A recent example of such difficulties is the expansion at Roberts Bank, British Columbia, where environmental impact assessment studies and their public review took almost six years from initial expansion applications until the time of approval. Dust Control Modern coal terminal dust control techniques usually consist of water sprays at strategic locations to suppress dust. The application points include rail car or barge dumper, main conveyor transfers, perimeter sprays around stockpiles, stacker/reclaimer, ship-loader transfers, and loading spout. The water sprays may include a chemical wetting agent or surfactant to reduce the water requirement and increase effectiveness. Recently there have been advances with development of effective micro foam agglomerating agents. In these systems, a micro foam with very small bubble sizes is sprayed into the coal stream. The foam fills the interstices between coal particles and wets the coal fines. These systems have proven to be very effective and usually one application before stockpiling and one upon reclaiming will markedly reduce the coal dusting. Stockpile perimeter sprays can be operated either manually or at the sophisticated terminal, actuated by a computerized control system that senses key environmental conditions such as humidity, precipitation, and wind velocity. Most modern terminals collect the drainage from the stockpile area, remove the solids in settling basins, then recirculate the water to reduce water requirements and effluents from the site. Dusting of long-term storage stockpiles can be reduced by spraying the piles with chemical resin or latex binding compounds to seal the surface. These compounds also can minimize erosion of the pile by rainfall. Dust collection with air evacuation systems and cyclone or wet scrubbers can be used at key areas such as rail car dumpers, main conveyor transfers, and ship-loader spouts. The trend in dust control is away from dust collection since most dust collectors are high maintenance items requiring good operator supervision and servicing. Coal handling conveyors are usually open and uncovered. However, in areas requiring special attention they may be covered or even completely enclosed. Dust generation from terminal roads is often a significant amount of the total dust emitted from a terminal. To reduce this dusting, roadways where traffic is heavy can be paved or sprayed by water trucks. Speed limits can be enforced and use of tracked mobile equipment for stockpile handling rather than rubber-tired loaders is encouraged by authorities. Noise Abatement Terminals located close to residential areas are often faced with noise control problems. Noise can be one of the most difficult environmental problems to solve. Usually, use of electrically-powered equipment is encouraged to reduce noise levels. Rail car dumper houses can be totally enclosed to reduce both dust and noise emissions. Diesel locomotives can be fitted with special muffling devices. Green belts of trees surrounding a terminal or the ap-

Jan 7, 1983

By İbrahim Çınar, Hakan Özşen

Mine workers in heavy and dangerous work are under several physical risk factors, for example temperature, humidity, noise, vibration, lighting and air velocity. Thermal comfort includes parameters such as air temperature, air humidity, air flow rate, radiant heat, metabolic rate and garment insulation. In this study, thermal comfort conditions were evaluated using thermal comfort indices defined as predicted mean vote (PMV) and predicted percentage dissatisfied (PPD) which were determined by measurements taken from an underground coal mine for approximately 100 days. Although the metabolic rate (light work) was kept at 2 met, it was found that predicted mean vote ranged between − 2.58 and 1.68. The predicted percentage dissatisfied index was found to reach 95%. According to the results, it can be seen that thermal comfort may have negative effects on occupational health and safety. The change in thermal comfort index values in the Soma Underground Coal Mine was investigated in detail and the reasons for the changes were determined. Furthermore, determining the optimal working environment for the mine workers was also an aim of this study.

By Lawrence M. Zanko

Eighteen coarse taconite tailings samples were collected in 2000-2001 from five western Mesabi Range taconite (iron ore) operations located in northern Minnesota, i.e., EVTAC, Hibbing Taconite (Hibtac), USX Minntac, Ispat Inland (Minorca), and National Steel Pellet Company (NSPC), to test their physical, geological, chemical, and mineralogical properties [Zanko, L.M., Niles, H.B., Oreskovich, J.A., 2003. Properties and aggregate potential of coarse taconite tailings from five Minnesota taconite operations, Minnesota Department of Transportation, Local Road Research Board, St. Paul, MN, Report No. 2004-06 (also as Natural Resources Research Institute technical report, NRRI/TR-2003/44)]. The goal was to assemble a body of technical data that could be used to better assess the potential of using a crushed taconite mining byproduct like coarse tailings for more widespread construction aggregate purposes, primarily in roads and high¬ways. An important part of the mineralogical assessment included X-ray diffraction (XRD) analyses and microscopic (polarized light microscopy, scanning electron microscopy, and transmission electron microscopy, i.e., PLM, SEM, and TEM, respectively) evaluation of the size and shape (morphological) characteristics of potentially respirable microscopic mineral particles and fragments. Quantitative mineralogy, based on XRD analyses, showed that the dominant mineral in all samples was quartz (55-60%), followed by much smaller amounts of iron oxides, carbonates, and silicates. Specialized microscopic analyses and testing performed by the RJ Lee Group, Monroeville, PA, on both pulverized (-200 mesh, or 0.075 mm) and as-is sample composites showed that no regulated asbestos minerals or amphibole minerals were detected in the western Mesabi Range samples. A small number (26) of non-asbestos and non¬amphibole mineral cleavage fragments/mineral fibers were detected by SEM out of 1000 fields analyzed, but most were identified as min¬nesotaite and talc, silicate minerals common to the Biwabik Iron Formation. Amphibole minerals, absent in coarse tailings samples from the five western Mesabi Range taconite operations, were present in a single eastern Biwabik Iron Formation sample collected in 2003 for Lake County from the Cliffs Northshore operation in Silver Bay, MN. Importantly, the Superfund Method for the Determination of Releasable Asbestos in Soils and Bulk Materials [United States Environ¬mental Protection Agency (USEPA), 1997. Superfund method for the determination of releasable asbestos in soils and bulk materials, EPA 540-R-97-028, U.S. Environmental Protection Agency, Washington], as modified by Berman and Kolk [Berman, D.W., Kolk, A.J., 2000. Modified elutriator method for the determination of asbestos in soils and bulk materials, Revision 1: Submitted to the U.S. Envi¬ronmental Protection Agency, Region 8, May 23, 2000] failed to generate any protocol fibers, i.e., fibers longer than 5 µm and thinner than 0.5 µm, from either the western coarse tailings samples or the single eastern Biwabik Iron Formation sample. The combined findings suggest coarse tailings and other taconite mining byproducts should be treated with the same common sense safety and industrial hygiene approach practiced for all mineral-based materials that have the potential to generate respirable dust. © 2007 Elsevier Inc. All rights reserved.

Jan 1, 2007