Search Documents

By Thomas Gleason

Wet scrubbing of fine coal from Thermal dryers poses a number of problems in adapting the gas cleaning equipment for required clean-up of the fine particulate matter. Among then are: 1. The dust In the gases leaving the Thermal dryer cyclone-s is often extremely fine with high percentages of the total dust loading less than one (1) micron in size. 2, The flue gas entering the scrubber is corrosive since the coal fired in the thermal dryer furnace is in the range of 0.7% by weight sulphur or higher. Therefore comparatively high cost stainless steel alloys or corrosion resistant linings are required for a satisfactory service life. 3. Requirements for residual coal loadings leaving the gas e scrubber are continually being lowered while modern coal preparation operation is imposing heavier burdens on the collection system through introduction into the Thermal dryer system of very fine coal previously not recovered. The advent of flotation systems in increasing numbers is typical of this trend 4. The installation of a scrubbing system on Thermal dryers is made primarily to reduce air pollution and product recovery value is of little or no value. Therefore the operating costs, that is, of gas pressure drop and water requirements must be held to a minimum.

Jan 1, 1962

By John P. Norton

Microcystaline silica has been mined in Illinois from the Clear Creek formation since the turn of the century, especially in the area around Tamms in Alexander County, in the southernmost part of the state. Production of this silica, consumed mainly by the abrasives and coatings industries but also sought after for many filler/extender uses, has grown with the economy with several new applications overshadowing traditional markets in recent years. Such an important commodity was given the early attention of the Illinois State Geological Survey and a very complete report was issued in 1953 (Report of Investigations No. 166), authored by J. E. Lamar. The mining and processing of the silica ore has changed very little since the first reported production in 1906, although emphasis has been placed on the production of the finer sized grades to meet newer market requirements. Industrial Mineral Notes 40, published by the Illinois State Geological Survey in June 1970, describes a method by which a less than 1-micron fraction could be commercially produced from the readily available finest commercial grade presently being marketed (99% minus 10 microns). The finer grades exhibit to a lesser degree the reinforcement, high flatting efficiency, thickening and dry brightness properties associated with the synthetically produced silicas. It is expected that the extremely fine grades of microcrystaline silica will become accepted in the markets that now use a combination of precipitated silica and less expensive extender/filler minerals such as kaolin or calcium carbonate.

Jan 1, 1976

By R. K. Mensah-Biney, M. T. Hepworth, K. J. Reid

The loading characteristics of gold-bromide species onto activated carbon were evaluated using a batch system. The overall loading of gold onto activated carbon was rapid for the first few hours, but it continued without cessation as a result of the reduction of gold. Therefore, conventional equilibrium considerations were not applicable. Although loading continued slowly after several days, an abnormally high, loading capacity value of 10-12 meq/g carbon (650-800 kg Au/t) could be attained in 72 hours. The loading of gold-bromo species by activated carbon was by the mass transfer of (AuBr4)- species to the external surface to be reduced to metallic gold by carbon. Elution of gold from loaded carbon was feasible provided the carbon had not been loaded to high capacity values. If loading is carried to high levels, complete elution becomes impractical, and the gold may be recovered by ashing the carbon. For the high loading capacities observed, this option would appear to be cost effective. The effect of several variables on the loading capacity of the activated carbon for gold-bromo species is discussed.

Jan 1, 1994

By M. Hodgson

The redox reactions that occur on pyrrhotite and pentlandite in contact with oxygenated deionized water were examined using voltammetry. Reactions were put forward in which both minerals were progressively hydroxylated to form thermodynamically metastable surface intermediate products. These intermediates were modelled as metal deficient sulphides where a sulphurous layer was coordinated onto the remaining metal sites via polysulphides. Prior to hydroxylation pentlandite exhibited changes in the surface stoichiometry which were not related to pH effects. The formation of polysuiphide-sulphur intermediates were believed to promote collectorless; flotability for the two minerals. Microflotation tests (0.3 g samples) verified that the surface potential and particle size affected the flotation response, excessive oxidation inhibiting the minerals' flotability. Larger scale tests using ore samples (30 g) confirmed that the extent of pulp oxidation, particle size distribution and the presence of frothers affected the flotation response, the findings being in accordance with the postulated model for the hydrophobic species generated on the pentlandite and pyrrhotite surfaces.

Jan 1, 1985

By M. Govinda Raj, S. Sridhar, M. Aruna

Hand-transmitted vibration (HTV) exposure is associated with various health risks for operators of mobile mining equipment (MME). The case–control research was conducted to determine the musculoskeletal disorder (MSD) risks associated with exposure to HTVs in the exposed (case) and non-exposed (control) groups. HTV readings were measured at the interface between the hand and the steering device using the SV 105B triaxial hand accelerometer connected to the SV106 human vibration analyzer involving 40 MME operators in accordance with ISO 5349:2001 guidelines. A questionnaire survey was also carried out among both the study groups using Cornell Musculoskeletal Discomfort Questionnaire. The European Union's 2002/44/E.C. was used to assess the health risks posed to the MME operators. Twenty-eight out of the 40 MMEs were generating HTVs exceeding the stipulated daily limits of vibration, putting 70% of the operators at increased risk for developing MSDs. The case group was found to have an elevated risk of exposure with odds ratio (OR) 7.56 (95% confidence interval (CI), 1.159, 49.39) and OR 12.80 (95% CI, 2.436, 67.285) times more likely than the control group to suffer discomfort in the left shoulder and left wrist, respectively, indicating increased risk of exposure to HTV. Additionally, cases had elevated risk associated with exposure to tobacco, OR 9.35(95% CI, 1.856, 47.129) compared to those who did not use tobacco. MSDs were more prevalent in the case group compared to the control group. This observation was validated by the field investigations and the responses of MME operators to the questionnaires.

Aug 2, 2022

By Carla L. Zenti

In recent years, considerable advances have taken place worldwide in the design and construction of first tunnel linings. With these advances, there is a tendency to move away from traditional support that includes heavy open profiles of rolled steel arches, to a lighter solution with the use of an optimized tubular steel cross section rib, and shotcrete reinforced with steel mesh and/or steel fibers, providing a continuous support (Lunardi, 1982). The development of tubular ribs has provided greater design options, increasing flexibility to engineers and contractors while providing a efficient and cost effective construction method. In this article, the authors describe numerical and experimental investigation on this problem, suggesting as a new first lining steel arch design approach by using tubular ribs cross section as new technical solution for first lining underground support.

Jan 1, 2012

By Bruce Watzman

"Few issues are more important to the National Mining Association (NMA), the U.S. mining industry and NMA’s MINExpo International 2016 exhibitors than safety.Global mining safety and health is a journey necessitating continuous improvement, collaboration and innovation on the part of both mining operators and their suppliers.MINExpo 2016, which takes place Sept. 26- 28, 2016, in Las Vegas, provides attendees with the opportunity to view technologies to help refine management of mining safety and health, utilizing NMA’s CORESafety system. CORESafety ‘One of the best’Launched by NMA in 2011 and moving forward ever since, CORESafety is driving continuous improvement in safety and health performance among participating industry companies by shifting from a command-andcontrol regulatory approach to a risk-based systems approach built on the Plan-Do-Check-Act model (Fig. 1).Considered an exemplary safety and health management system, NMA’s CORESafety system helps mining operators change their approach to safety and health management by enhancing the safety and health culture throughout their organizations. Although it is challenging to consistently and completely control all the factors and variables occurring in daily mining operations, experience has shown that applying systematic controls to as many variables as possible is the most successful approach for improvement in mining safety and health.When embarking upon the development of the CORESafety framework, NMA’s leadership set an ambitious goal to eliminate fatalities and reduce the injury rate 50 percent in five years, or the “0-50-5” goal. While the goal has not been met yet, the steady progress has been extraordinary with fatalities among participating companies dropping 45 percent during the period 2011-2015 (Fig. 2). Data also demonstrate that, as participating companies increase their level of implementation, total injury rates have also declined (Fig. 3).In a September 2015 interview with NMA, Penn State University mining engineering Professor Jeffrey Kohler praised CORESafety as “an inspired and timely program that brings together key elements to achieve safety and health goals.”"

Sep 1, 2016

By Hans Ruge

The El Soldado copper mineralization occurs as relatively high-grade irregular ore bodies with assay contacts and with frequent inclusions of barren rock. The sampling method must be timely for production grade control purposes, as well as accurate and inexpensive. Sampling techniques evolved from sampling dump cars at the haulage level to sampling scooptrams at the loading pockets. These were abandoned in favor of sampling production blast holes. Several sampling alternatives are discussed. These involve the selection of optimum volumes and sampling frequencies while taking into consideration geological parameters and statistical analyses of sampling data.

Jan 1, 1984

By S. K. Kawatra, J. A. Halt

"Low-grade iron ores are finely ground and processed to recover iron-bearing minerals. However, the iron-rich powder is too fine to be used directly in blast furnaces and most direct reduction furnaces, and must be agglomerated or pelletized into a usable product called “pellets.” Bentonite clay has traditionally been used as a binder to make iron ore concentrate pellets, but it is expensive and contaminates the pellets. Organic binders may be a viable alternative to bentonite clay. This manuscript reviews organic materials that have been used to make iron ore concentrate pellets. Included are discussions on the development of organic binders, common pros and cons to organic binder use, organic binder structure and its effects on agglomeration, and additives to organic binders.IntroductionIron ore agglomeration turns finely disseminated, low-grade iron ores into a usable product, called pellets. During pellet production, fine-grained, iron-rich minerals are liberated from low-grade ores, concentrated, and agglomerated into round balls that are thermally hardened or cold-bonded to form pellets. Pellets are then transported to blast furnaces or direct reduction operations where they are used to produce iron; iron is further refined and shaped into the wide variety of steel-based industrial and consumer products in use today.Over the years, pellet production has become increasingly more prevalent with the increased exploitation of low-grade iron ores and increased iron and steel consumption around the world. In 2010, world iron ore pellet production was 388 Mt. It could be argued that the current pellet production process has been enabled by the use of binders – practical experience has shown that it would be nearly impossible to agglomerate iron ore concentrates using rotary drums and discs without using a binder."

Jan 1, 2015

By Irene Bendanillo, Canon Cheung, Justin Lianides, Derek Penrice

The SLAC National Accelerator Laboratory’s two-mile-long particle accelerator generates the world’s brightest X-rays from its Linac Coherent Light Source (LCLS) freeelectron laser. This facility has driven groundbreaking discoveries in medicine and industry. The LCLS-II-HE project will provide a significant increase in laser energy, allowing cutting-edge research in fields including biology and environmental science. A key project component is the Low Emittance Injector Tunnel (LEIT), a 240-foot-long tunnel to be built alongside the existing accelerator and connected to it via a 30-footlong Transfer Tunnel. This paper discusses site and scientific constraints that led to the selection of the LEIT configuration: tunnels to be constructed using the sequential excavation method in mixed-face conditions comprising native rock and placed backfill, and critical design considerations including protection of overlying and adjacent historic structures and structural accommodation of near-fault seismic loading.

Jun 13, 2023

By A. Vaillant

Classifiers that are used to separate granular materials into a coarse and a fine stream, are considered. Fundamental Equations are presented which apply to all, such Classifiers and all feed size distributions. The practical, real Classifier is compared quantitatively with the perfect. Classifier. A Formula is introduced for the Real Classifier Selectivity, that defines what portion of each particle size is sent to the coarse outlet duct. This selectivity function is characterized by three Parameters, one of which (b) is a numerical measure of the sharpness of classification. A new dimensionless variable (J) appears in Equations and Graphs for recirculating load, product size distribution and specific surface in the classified product. This variable combines the effects of sharpness of separation, Classifier setting and fineness of a Rosin-Rammler Type feed to the Classifier. Classifier efficiency is defined, based on Specific Surface.

Jan 1, 1967

By Derek du Preez, Andrew Hall, Timothy M. Pelech

Net Present Value (NPV) derived from Discounted Cash Flow (DCF) analysis remains the dominant metric for evaluating mining projects despite its well-documented inability to capture managerial flexibility under uncertainty. DCF assumes that all risks are perfectly priced by financial markets. This is an unlikely assumption for volatile commodity prices, geological variability, or the array of mining technical and operational risks present on all mine sites. Real Options Analysis (ROA) was developed to remedy this limitation by explicitly valuing the ability of managers to defer, expand, scale, switch, or abandon investments as new information emerges, and to capture upside and mitigate downside risks. While ROA is philosophically correct and routinely shows an uplift in project value compared with DCF, its practical application at industrial scale is severely constrained, ROA faces the reality of a combinatorial explosion in complexity of decision trees, Monte Carlo simulations and other models required when multiple interdependent or sequential options exist across numerous mining zones and time periods. The AMC Hill of Value® (HoV) process adopts the same intellectual foundation as ROA, that flexibility has economic value, but operationalizes it through a far more robust and scalable architecture. It is built on parametric relationships, rapid scheduling, and multi-objective evolutionary optimisation. HoV can evaluate millions of compound, interdependent real options in a single optimisation run, delivering resilient, adaptive strategies that preserve managerial flexibility while simultaneously optimising NPV, mine life, risk exposure, and other corporate objectives. This paper demonstrates that HoV is the practical, industrial-scale embodiment of real options thinking in mining: it discovers, ranks, and translates the most valuable real options into strategic mine plans, overcoming the scalability barriers that have prevented widespread adoption of classical ROA.

Feb 22, 2026

By H. O. Seigel

This is an introductory paper on a new method of prospecting for mineral deposits which has been developed by Scintrex Limited. The method, which we call Luminex, for luminescent mineral exploration, is based on time- resolved mineral luminescence created by an ultraviolet light source. It has the ability to detect and resolve a group of key minerals which are either ore minerals themselves, or more often, are accessory or pathfinder minerals for certain types of economic ore deposits. Fortunately, these minerals are commonly found at the earth's surface, even in areas of considerable weathering. The method extends the range of mineral deposits which are remotely detectable from the air to include those such as tungsten, tin, molybdenum, gold and bedded lead-zinc deposits and, is therefore, a natural supplement to our three classical methods of airborne geophysics.

Jan 1, 1983

By Carl C. Martin

The treatment of ores in preparation for fatty acid flotation is characterized by a wide divergence in methods, and attempts to define "common practice", even for the same type of mineral, are usually of little value because of the numerous exceptions. Such factors as desliming, pulp density, pulp temperatures, and reagents for conditioning are successfully employed under conditions representing almost extreme opposites. More precise control of variables is necessary than with sulphydric flotation processes It appears likely that variations result from independent development of a process from the multitude of variables that characterize fatty acid flotation and the ores of non-metallic minerals. Consequently, a symposium is a suitable way of presenting a summary of pretreatment methods for fatty acid flotation processes, together with froth control practices, as they exist today.

Jan 1, 1959

By Steve Kral

"Liebherr, as most anyone involved with the global mining industry knows, is one of the world’s largest makers of mining and construction heavy equipment. The familyowned company has been around since the 1940s and, according to Stefan Heissler, by the end of next year, will employ about 44,500 people worldwide. Heissler is a member of the board of directors of Liebherr International AG.It all started for the Switzerland-based company when Hans Liebherr first recognized a need for heavy equipment in the construction industry, Heissler said. His first product, introduced in 1949, was the TK10, a mobile crane that, at the time, was a groundbreaking innovation to the heavy construction industry. From there, the company began its growth into a world-leading heavy equipment manufacturer that always relied on innovation.In October, Liebherr gathered a group of mining and construction magazine editors in Leoben, Austria to take a look at the company’s latest addition to the global mining and construction markets. On the mining side, Liebherr provided a demonstration of its T-236 100-t (110-st) haul truck and the PR- 766 50-st (55-st) crawler tractor. The one-day demonstration took place at the Erzberg iron mine near Leoben, where both machines are being proven.The Erzberg Mine, operated by VA Ersberg, has been in operation for about 1,300 years and is said to be Europe’s largest surface mine. It employs about 230 people and mines about 12 Mt/a (13,200 million stpy) of ore, producing about 3 Mt/a (3.3 million stpy) of fine-grained iron ore.T-236 rigid-frame truckThe new T-236 rigid-frame dump truck, with a diesel electric drive system, is Liebherr’s entry into the 100-t (110-st) class and is the first in this class with a four-corner, oilimmersed braking system. The haul truck was first introduced during the 2016 MinExpo in Las Vegas, NV. The unit has since successfully completed its testing phase and is currently in its first field operation trials at the Erzberg iron mine in Austria."

Jan 12, 2017

By W. A. Zingg

Impervious zones in copper waste heaps create a problem in contacting the rock with leaching solutions. These zones are normally associated with compacted layers .formed on the surface of each lift by dump truck traffic and by disintegration of the rock exposed to atmospheric conditions. These layers are usually only a few feet in depth--but, nevertheless, act as barriers to vertical flow causing the leach solution to perch in the heap, Consequently, much of the rock remains untouched and the leach solution breaks out the side of the heap instead of continuing downward to bedrock. One solution to this problem is breaking the hard pans with explosive charges. However, to use explosives means adopting new explosive materials and methods. To use this process successfully requires finding answers to operating conditions inherent to waste heaps. Foremost among these are: (1) type and size of casing that can be used because of limitations brought about by drilling problems, caving and, corrosive conditions; (2) perforating the casing at required levels; (3) an explosive capable of being pumped; (4) obtaining detonation of the, main charges through, the wail of the casing; (5) an explosive with the ability to propagate through the voids of the rubble and one which is not affected by water, acidic solutions, or back pressure conditions from hydrostatic heads; (6) to heave and rupture the compacted zones without chambering or recompressing the waste material.

Jan 1, 1970

By John Batchelder

The Copper Canyon Cu-Au-Ag deposits include two geologically distinct hypogene ore bodies developed primarily in late Paleozoic rocks adjacent to a 38-m.y.-old potassic-altered granodiorite, whose emplacement seems to have been controlled largely by the Virgin fault, a north-striking normal fault. Widespread but subeconomic concentrations of sulfides as fracture and cavity fillings in skarn apparently preceded the final intrusion of the granodiorite. In the west ore body, metals reached ore-grade concentrations through the massive replacement of andradite by chalcopyrite, pyrrhotite, and pyrite mineral assemblages. The east ore body probably formed after the granodiorite reached its present level. Calculated 6dD values of water in equilibrium with primary and secondary biotites range from -76 to -99 per mil at temperatures indicated by d180 values from coexisting quartz and biotite. The lightest values are in secondary biotite from the east ore body. These data suggest that fluids associated with potassic alteration here were most likely composed of magmatic water mixed with some meteoric water.

Jan 1, 1976

By Wayne D. Gould

The Cities Service Company's Pinto Valley mine and concentrator lie about 6 miles west of the town of Miami, Arizona at an elevation of approximately 4,000 feet above sea level. The concentrator started its first ballmill in July 74 and all six were available by November. Every effort was made to reduce capital costs, consequently, each unit process was studied critically to eliminate excess capital costs without loss of efficiency. Equipment selection was made on the basis of proven dependability and operating costs rather than on low bids. The result is a very workable plant with some important innovations. The concentrator is nominally 40,000 tons per day. The flowsheet is typical with 3 stage crushing, single stage closed circuit grinding, flotation, regrinding of rougher concentrate and cleaning of the rougher concentrate. The major equipment list is: 1 60 x 89 Traylor Primary Crusher 1 84" x 20' Stevens-Adamson Apron Feeder 3 7' x 16' Double Deck Tyler Screen 3 7' Nordberg Standard Crushers 6 8' x 20' Tyler Screens

Jan 1, 1975

By F. Segobia, H. Lozano, M. Portal, F. Ysla, L. Goicochea

This case study evaluates the long- term physical stability of various historical mining structures remediated by the Center for Mining Environmental Research and Studies (CIEMAN) in Hualgayoc, Cajamarca, Peru. The region has a long history of mining activity, with remnants dating back to pre-Inca times. CIEMAN has assumed responsibility for remediating 286 environmental liabilities in the area, including adits, shafts, pits, tailings, and waste rock dumps. The study analyzes the methods employed to stabilize these structures, including geotechnical engineering techniques and revegetation. Long-term monitoring results are presented, assessing the effectiveness of remediation measures and predicting the future stability of the structures. This study highlights the importance of responsible remediation of mining environmental liabilities to ensure the safety and sustainability of communities and ecosystems affected by historical mining.

Feb 1, 2025

By Jonas Svensson

The Grangcold Pellet Process - for which patents have been applied or already granted in a number of countries - uses a hydraulic adhesive such as Portland cement, slag cements, pozzolanic cements, etc., for the production of cold bonded pellets. The idea of using a hydraulic binder for the agglomeration of iron ore fines is not new. Portland cement was proposed as an adhesive for cold bonded iron ore briquettes in patents granted more than 50 years ago (1). In a report on the briquetting of iron ore fines, published in Stahl and Eisen 1959 (2), it is stated that briquettes bonded with Portland cement are used on a small scale at on ironwork in Germany. According to the report, the briquettes showed excellent strength in the blast furnace although their general use was made impossible because they required a long hardening time, during which they are sticky, soft and difficult to store and handle. The Grangcold Pellet "recess has overcome this particular disadvantage by mixing the balls with a suitable amount of the balling concentrate before storing them. The pellets are embedded in the concentrate during storing in such a way that they are isolated from each other and thus prevented from sticking together to form clusters. Thanks to the embedding concentrate, the pellets are subjected to a more or less uniform pressure from all sides which does not deform them. Thus the mixture can he stored in a stockpile or in a silo until the pellets have hardened sufficiently. The concentrate is separated from the pellets by means of screening. The concentrate is returned to the balling operation and the pellets are either shipped to the blast furnace or stored for final hardening.

Jan 1, 1969