Search Documents

By Evan J. Owen, Virginia T. McLemore

The Zuni Mountains, located in Cibola County, New Mexico is an uplifted area that exposes Proterozoic igneous and metamorphic rocks overlain by Permian and younger sediments. Sedimentary-hosted Cu deposits and fluorite veins in the district have recorded production, but other deposits exist. Proterozoic ultramafic rocks may host Ni and PGE. A recent regional stream sediment survey collected 76 samples as part of an exploration geochemistry course at New Mexico Tech with the goal of assessing the critical minerals potential of the district. Whole rock and trace element chemistry of the sediment samples (<2 mm) show a variety of critical minerals possibly worthy of future targeted exploration including up to 700 ppm As, 2100 ppm Ba, 26 ppm Bi, 25 ppm Co, 640 ppm Cu, 145 ppm Ni, 110 ppm Sb, 170 ppm V, and 500 ppm Zr. Positive correlation between Bi, As, Cu, and Sb suggest that these critical minerals are found together within copper veins related to shear zones in the district. Samples collected from streams that drained outcrop of mafic and ultramafic rocks were found to generally contain more Ni, Co, and V. Samples elevated in Ni will be reanalyzed for PGE.

Feb 1, 2025

By S. Gaillard, E. Cauda

"Diesel particulate matter (DPM) is an occupational health hazard in underground mines. It generally occurs in the submicrometer size range and is often present in the mine atmosphere with significant concentrations of dust particles that tend to occur in the supramicrometer size range. As dust can interfere with analytical methods to measure DPM, it is often removed from a sample stream using an impactor-type size selector such as the DPM impactor (DPMI). Because the DPMI physically removes oversized particles from the stream, its performance may be gradually reduced with aging. Sharp-cut cyclones (SCCs) are an alternative size selector for DPM sampling applications, with a major advantage that, by design, they should not be susceptible to rapid aging. This paper presents the results of a field study designed to compare the performance of aged versus new/clean DPMIs and SCCs in an underground mine. DPMI aging resulted in clogging of the device and, eventually, a reduction of its effective particle cut size, but when sample flow rate was maintained, DPM sample mass collection was not affected until significant aging had occurred. Under the conditions of this study, the effects of SCC aging were observed to be minimal at the end of the study period. IntroductionSubmicrometer-sized particles are increasingly recognized as significant respiratory health hazards (Cantrell and Watts, 1997; Kenny, Gussman and Meyer, 2000; Ristovski et al., 2012). Diesel particulate matter (DPM) represents a major source of submicrometer particles in both public and occupational environments (Kittelson, 1998; Abdul-Khalek et al., 1998). Relative to other occupational groups, underground miners can have some of the highest DPM exposures due to their work in confined spaces where large diesel equipment is used (U.S. Environmental Protection Agency, 2002; Grau et al., 2004). DPM largely consists of solid elemental carbon (EC), commonly known as soot, and organic carbon (OC) that may be sorbed to EC particles (Kittleson, 1998; Abdul-Khalek et al., 1998). EC and OC can be measured by thermal-optical methods such as the U.S. National Institute for Occupational Safety and Health (NIOSH) 5040 standard method (Birch, 2016), and their sum is referred to as total carbon (TC). While the complex nature of DPM does not allow for its direct measurement, both TC and EC have been accepted as suitable surrogates for monitoring occupational exposures to DPM (Noll et al., 2007; Birch, 2016)."

Jan 8, 2018

By V. D. Hanson

When maintenance of a plant or operation is under discussion immediately three "M&apos;s", all in short supply, are brought to mind - money, men and markets. This paper will present what currently is being done at our plants and its effect on the 3 "M&apos;s". Examination of coal realization figures (F.O.B. Mine) from 1945 to the present reveals the fact that open and free competition can and will meet market conditions. The industry, without benefit of advantages afforded tax and transportation wise to oil and gas, remains the backbone of the energy market of United States. Figure No. 1 shows the realization figures from 1945 through 1962 compared to the hourly earnings. Note that through 1945 to 1948 F.O.B. prices increased $1.93 per ton while hourly earnings increased $.66 per hour. Since 1948 (with the ex¬ception of 1957) F.O.B. prices have declined $.45/ton, while hourly earnings have increased $1.23 per hour. Basically the maintenance men possibly represent the highest increment rate in the overall hourly earning.

Jan 1, 1963

By Romeo S. Jurani

Bulkspray cooling has been economically applied in cooling the hot environment of South African gold mines for the past two decades. Its success in that country led to its introduction at Gulf Mineral Resources Co.&apos;s Mt. Taylor Mine in 1981 when increased drifting imposed additional cooling requirements. The bulkspray cooler developed and used at Mt. Taylor has a heat transfer capability of about 500 to 1500 kW. It is compact and portable, designed to be moved as required to maintain working temperatures in the advancing drift faces.

Jan 1, 1983

By I. D. Lindley

The Wild Dog vein gold deposit in East New Britain Province, Papua New Guinea, forms part of a recently discovered 26 km zone of auriferous quartz vein mineralisation. The deposit, which was discovered in July 1983, has no silt anomaly, and a panned concentrate anomaly and float train restricted to within 500 m and 800 m respectively, of the discovery outcrop. Discovery of the Wild Dog deposit was a result of the methodical followup of regional panning which, as followup progressed, was replaced in importance by float sampling. Of the sampling methods used during the exploration leading to discovery, panning and float followup provided immediate indications of the presence of mineralisation. This high degree of spontaneity of followup is not provided by geochemical techniques, and has obvious advantages in high cost exploration for precious metal deposits in remote locations.

Jan 1, 1988

By D. D. Runnells, G. A. Doyle

The quality of water in mine pit lakes depends in part on the physical limnology, including such factors as thermal and chemical stratification, turnover and the development of anoxic conditions with depth. Limnologic data collected from four existing pit lakes in Montana and Saskatchewan indicate that pit lakes develop a thermocline (temperature stratification) in the upper 10 to 30 m (33 to 100 ft) of the water column. Two of the pit lakes, 26- and 55-m (85and 180 ft) deep, undergo seasonal turnover of the entire water column, whereas two deeper pit lakes, 110- and 240-m (360- to 790 ft) deep, undergo seasonal turnover of only the upper portion of the water column. In the deeper lakes, seasonal mixing does not extend through the entire water column, and a distinct chemocline develops with depth.

Jan 1, 1998

By M. P. Fahey

A significant amount of silca is recovered in the rougher stage of anionic flotation of Florida apatite. This recovery, in the past, has been attributed to both entrainment and cation activated flotation. This study shows that by using a transport factor, it is possible to determine the contribution of each mechanism towards silica recovery. Further, it is shown that the concentration of cations in the conditioning water significantly affects both the amount of silica recovered due to entrainment and true flotation. Further confirmation of this phenomenon was obtained by Ca++ doping of the conditioning water and by using a sodium silicate depressant.

Jan 1, 1996

By Jeff Poe

When a takeup weight is offset to the side of a conveyor, a wire rope is commonly routed from the takeup weight through a series of sheaves to the takeup carriage. The friction developed from a series of wire rope sheaves can effect the actual belt tension at the make up carriage. Through real-mime testing the actual tension on a makeup carriage was recorded with data acquisition using an internally strain-gauged turnbuckle. The wire rope used to transfer the makeup weight to the makeup carriage was routed through a series of lubricated bronzed bushed sheaves. The tension on the makeup carriage was found to be as much as 26% higher than the weight of the makeup due to the friction in the sheaves. A detailed discussion of the testing and results will be made.

Jan 1, 2000

By Niels Jonassen

INTRODUCTION The occurrence of the radioactive element radium, [2gg~a], often in trace amounts, in the crust of the earth gives rise to a flux of the daughter product radon, [&apos;ii~n], across the earth-air interface. This so-called exhalation process has been studied by many investigators [KO 45, Kra 64, Pe 66, Wi 741] over several decades. In the earlier investigations the exhalation process was studied in a purely geophysical context, but over the last 20 years it has been realized, that under certain conditions the exhalation may be intense enough to also have radiological implications. This is for example the case where relatively radium-rich wastes or by-products, like uranium mill tailings and phospho-gypsum, are stored in larger quantities. In order to be able to predict the radiological impact on the environnent it is necessary to know the rate of exhalation of radon from the surface of the exhaling material. Usually the determination of these exhalation rates has been done by measurements in situ directly upon the accumulated material [~le 74, Ha 791. Although such field measurements have the obvious merit of dealing directly with the full scale problem, the results are often lacking in generality, making predictions for other situations difficult or even impossible. The present paper describes some results of an investigation where it is attempted from laboratory measurements on samples of limited size to obtain material parameters, which are suited for extrapolating and predicting the radiational behaviour of larger accumulations of the material. THEORY Let us consider a sample of a radon exhaling material enclosed in a container with a dead space volume, Vd, and initially containing radon free air. If the total exhalation rate (number of atoms per unit time) is c, the radon concentration (number of atoms per unit volume) N will initially grow with the time t according to the equation [ ] where [R] is the decay constant of radon. As the concentration (or activity) in the container grows, the net exhalation rate will slow down because of back diffusion, and, furthermore, radon atoms may be removed from the container, not only by radioactive decay, but also by diffusion leakage [JO 81 ]. If, however,only the initial. part of the activity growth curve is considered, the total exhalation rate, c, is given by [c = r•Vd(2) where r is the initial activity growth rate in the container. Let the container be cylindrical with an inner cross-section S and filled to a height L with a radon exhaling material with the specific mass p, the porosity E, the radon pore production rate f and the diffusion length i. When the container is left open,i.e. the radon exhalation takes place into a virtually radon free room, the radon area exhalation rate, E, can be written [Jo 80] E = Ef?t tanh L.R (3) assuming the exhalation only takes place in one direction, towards the surface of the material. It appears that for values of L > 2•ithe area exhalation rate becomes E a = Efi (4) independently of the sample dimensions and the total exhalation rate c is then c = E •S (5) For L ;~ 0.5•i, tanh P _ k and equation (3) may be written E ~ EfL (6) then c = EfL•S = p•m= Em •m (7) where m is the mass of the sample and Em = P (8) is the mass exhalation rate. It thus appears that the radon exhalation rate from a given amount of material may often be conveniently expressed by c = E •Sfor L z 2•I (5) a orc = Em •mfor L0.5•i (7) where S is the total exhaling area and m the total exhaling mass, E and E the area and mass exhalation rates respectively defined by equations (4) and (8).]

Jan 1, 1981

By L. Adler

A systematic, balanced and inclusive formulation of the vast input data for mine design is presented. Since the quality of this statement severely influences subsquent design it is extremely important to senior mining engineers and the profession-at-large. If unfocussed, chaos can result along with serious ommisions. The basic categories, each a traditional one are: 1) Natural Conditions (geology and geography), 2) Company Capabilities (monetary and managerial), 3) Public Domain (regulations, contracts, good will, etc.) and 4) State of Art (mining engineering professionalism). To further reduce the data additional organizing principles were used: the distinctions of mining (vs. civil) engineering, proceeding from the general to particular, the basic engineering dimensions, and separating dependent from independent variables. The results are a unique and unified corpus, which anticipates the mine design procedure.

Jan 1, 1987

By R. E. Mitchell

The environmental impact assessment (EIA) is the accepted method for evaluating proposed mining and other industrial projects to obtain regulatory approval and to help companies plan for responsible development. Another increasingly common evaluation system for proposed projects is the environmental, social and health impact assessment (ESHIA). An ESHIA differs from an EIA for its generally more comprehensive and inclusive approach to evaluating potential impacts, such as on public health, and other features such as an ecosystem services approach to assessing biophysical and community impacts. An ESHIA may also be required by certain lenders for financing major projects. In this paper, EIA standards for the province of Alberta, Canada are discussed and compared to ESHIA. It concludes with several recommendations for consideration.

Jan 1, 2012

On Dec. 20, 2013, an 8-m (26.2-ft) diameter Robbins hybrid single shield/earth pressure balance tunnel boring machine (EPB TBM) was launched to bore the Grosvenor decline tunnel for Australia?s Anglo American coal mine. The machine was built using onsite first time assembly (OFTA) in order to fit within a tight project schedule. Assembly at the remote jobsite near Moranbah, Australia took about four-and-a-half months, and then the machine was walked down into a launch tunnel. Two decline tunnels, at grades of 1:6 and 1:8, will be used for mine access to new coal seams. The hybrid machine is tackling mixed ground conditions ranging from sand and clay to varying types of sedimentary hard rock up to 120 MPa UCS, as well as coal seams. Methane gas is expected to be present throughout the tunnel, so the machine has been designed as explosion-proof-compliant to ERZ-1. ?Grosvenor is the first underground coal mine in Queensland to use a TBM for drift construction,? said Glenn Tonkin, Grosvenor project director. ?We are proud to be pioneering this technology.? Only about 300 m (984 ft) of ground in each decline tunnel is expected to require EPB mode, while the rest of the tunnel will be bored in hard rock mode. Thus, the design was optimized toward hard rock excavation.

By Gregg W. Davidson, J. Andrew McGlenn, Frank Huber

The Second Narrows Water Supply Tunnel will ensure system reliability in the event of a major earthquake and increase the Greater Vancouver Water District’s capacity to meet the long-term needs of a growing population. The tunnel will be 1,100 m long and 6.5 m in diameter (3,610 LF × 21.3 ft), constructed under Burrard Inlet between North Vancouver and Burnaby in British Columbia. It will be excavated through mixed ground conditions under high groundwater pressure, using a slurry TBM, between a 72 m (236 ft) deep shaft in soil and a 110 m (361 ft) deep shaft in rock. The completed tunnel will accommodate three large-diameter water mains that will be installed as part of the tunnel contract. This paper presents the project from design and contractor procurement, into the current construction stage describing some of the unique challenges encountered during the project development to date.

Jun 13, 2021

By Hugh Boyd

Jet pulverization is a relatively new tool for fine grinding. It is not yet in general use in the mining and ore dressing fields, since most of the requirements in these areas have been for relatively coarse particle sizes. As the need for finer grinding increases - because of different ores, new products, and new values being sought - jet pulverization will, increasingly, be properly used.

Jan 1, 1969

By W. I. Enderlin, P. O. Jackson, J. A. Glissmeyer, K. B. Olsen

A reliable estimate of radon emissions to the environment from underground uranium mines was obtained through measurements of radon in ventilation air at 24 mines and from estimates of radon release from other mine sources. The total production of U308 from the mines sampled represents about 63% of the total U.S. production from underground mines (1978 statistics). Wide variation in the radon emission rate per unit of production was found from mine to mine. Using the total radon emitted and U308 produced by all mines sampled, an average of 26.7 Ci of radon was emitted per ton of U309 produced. The investigation includes a brief study of the sources of variation of the emission rates. A statistically significant relationship was found between the measured radon release rate and the cumulative ore production at several mines.

Jan 1, 1981

By O. Porterfield, M. O’Kane, M. Endersby

BHP Iron Ore initiated research programs in January 1995 to develop long-term plans for decommissioning waste rock material at its Mt. Whaleback operation. More than 2 Gt (2.2 billion st) of waste rock were deposited during the past 30 years. Ultimately, a total of 4 Gt (4.4 billion st) will be deposited in waste rock dumps constructed near the open pit. The Mt. Whaleback operation is located in a semiarid climate adjacent to Newman, Western Australia. The primary research program includes the development of technology for the long-term performance of the waste rock dumps with respect to vegetation, slope stability, surface runoff, erosion and water infiltration. This paper focuses on the design and implementation of a cover system to prevent water infiltration to the underlying waste rock. Data obtained from a laboratory program and from soil-atmosphere modeling was used to design horizontal field test plots. The construction of the horizontal surface field test plots is discussed together with the field instruments installed to monitor performance. The cover system is designed to maximize infiltration during wet periods for subsequent evapotranspiration while minimizing surface runoff. The result is a near-zero net infiltration to the underlying waste material. An important feature of the design is the use of run-of-mine waste material as the cover material. Monitoring is in progress and will continue for at least two annual wet/dry cycles. The optimum cover system should minimize the net infiltration of water to the underlying waste rock while maintaining physical and ecological integrity for long-term performance.

Jan 1, 2000

By Jose M. S. Ramos

This paper describes the slope stabilization procedure at Cauê Mine, Companhia Vale do Rio Doce - CVRD, Itabira, State of Minas Gerais, Brazil. Cauê Mine, is a large open pit, to produce about 41 million tons of iron ore during 1974, and an intensive program of investiga Lion was carried out to provide the basic data for stabilizing its slopes, The ultimate rock slope in the W area will be about 400 m high with dipping angles decreasing gradually from top to bottom of the pit. The investigations started in 1969 and since then many geologists and engineers, from both CVRD and Geotécnica S/A., assisted by international consultants, have given their contribution to the achievement of solutions. It is hoped that this paper may contribute to the slope stability of other mines in tropical climate.

Jan 1, 1974

By Arcy R., D&apos George

Removal of S02 from smelter gases is being investigated, using an innovative technique that results in the almost simultaneous recovery and production of elemental sulfur. S02 is removed from the gas stream by scrubbing with suitable aqueous salt solutions or high-boiling organic fluids. The S02-laden liquor is then reacted with H2S Crystalline, high-purity sulfur is instantly precipitated and, after filtration, the regenerated liquor is recycled. The H2S required for the process is produced by reacting a portion of the recovered sulfur with hydrogen or with methane and steam. The chemistry and results of preliminary laboratory research are discussed.

Jan 1, 1969

By C. G. Anderson

Extraction of valuable resources from complex orebodies will become more common. This is obvious for two reasons. First, the cleaner and more readily processed ores have continually been depleted through centuries of mining. Second, new technologies have evolved for effectively handling complex ores. One of these new processes has been in place at Sunshine since 1984. Based on sulfuric acid oxygen pressure leaching with nitric acid as an oxidizer, this patented technology allows silver and copper to be efficiently recovered from a complex sulfide concentrate. As efficient as it is, this process represents novel technology found nowhere else on an industrial scale. As such, a research program was undertaken in 1989 to optimize this leach process and to better understand it. From this study, several potential plant improvements were found and recommended. As a result, two of these options, nitric acid replacement by sodium nitrite and concentrate regrind are now used in day to day operation at Sunshine. Patenting of these changes was recently accomplished (1). Thus, the development, perceived mechanisms, plant integration and potential applicability of this technology will be covered in this paper.

Jan 1, 1994

By Taekhee Lee, Steven Mischler, Shawn Vanderslice

Diesel-powered equipment is widely used in the underground mining industry and their popularity results from properties including efficiency, versatility, reliability, and durability. In the U.S. approximately 7,700 diesel engines were used in 177 underground metal and nonmetal mines as of 2005 [MSHA 2005], and these numbers have likely increased since that time. Diesel engines have been shown to be a major contributor to submicron carbonaceous, respirable, and total particulate mass in the air of underground metal mines [Zielinska et al. 2002, McDonald et al. 2003], and their extensive use results in approximately 13,000 underground metal/nonmetal (M/NM) miners (MSHA 2005) in the U.S. being potentially exposed to aerosols and gases emitted by diesel engines (MSHA 2001, MSHA 2006). Exposure to diesel exhaust has been linked to adverse health outcomes including cancer, cardiovascular, and respiratory diseases (Attfield et al. 2012, Silverman et al. 2012), and in 2012 diesel exhaust was categorized by the International Agency for Research on Cancer (IARC) as a Group 1 human carcinogen (IARC 2012). Exposure to diesel particulate matter (DPM) is especially concerning for underground miners since underground mine environments have been shown to have some of the highest levels of diesel exhaust in the U.S. (EPA 2002, MSHA 2001, MSHA 2006, Pronk et al. 2009). Due to the potential for elevated DPM concentrations in mines, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/ nonmetal underground miners to DPM to an eight-hour time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, MSHA 2006, MSHA 2008). Since this rule went into effect, DPM exposures have been reduced, but are still elevated when compared to other occupations (Pronk et al. 2009, Noll et al. 2015). MSHA compliance data between 2005 to the present show that underground blasters represent 21% of all DPM overexposures in M/NM mines and are one of the highest exposed professions in mining often resulting from low ventilation in the area where blasters are working. Because mines have difficulty controlling DPM in these low ventilation areas, additional control technologies may be needed to reduce exposures. Administrative controls, where miners work on off schedules or upstream of diesel vehicles to avoid the exposures to DPM (Noll et al. 2015) is one possibility, but these types of solutions are not always feasible or practical. A canopy air curtain is another potential control technology to help reduce exposures of blasters to DPM. Listak and Beck (2012) showed that this control technology reduced respirable dust concentration under a roof bolter’s canopy by 67%–75% and recommended air velocities greater than 0.5 m/s for dust reductions of greater than 50%. Additional work showed that a canopy air curtain could be designed for a shuttle car, and some initial testing by the National Institute for Occupational Safety and Health (NIOSH) showed reductions of respirable mine dust between 66% to 70%. As seen in Figure 1, the canopy air curtain delivers clean air over the operator’s breathing zone. A fan draws in air through a filter to capture the dust and then supplies clean air beneath the canopy where a miner is working. The use of the canopy air curtain to reduce exposures to diesel particulate matter was first discussed by Noll et al. (2020). In this study the diesel canopy air curtain (DCAC) reduced the DPM concentrations under the canopy by up to 90%. For this research the DCAC was designed to attach to the basket cover of an ammonium nitrate fuel oil ( ANFO) loader (Figure 2) and provide clean air blowing over the miners as they work in the basket. The initial tests used clean air drawn from the mine’s intake and did not try to filter the DPM from the air. Filtering DPM has extra challenges when compared to filtering mine dust particles. The particles of DPM are smaller (submicron and nanometer) than dust particles (greater than 1 micron); therefore, the filtration system must be adjusted to capture submicron particles. A MERV 13 filter was used in previous canopy air curtain research on mine dust control, but this filter is only designed to capture 50%–75% of submicron particles, and this capture efficiency is too low for removing DPM, so a higher efficiency filter is needed. Higher efficiency filters increase the pressure across the filter media which results in decreased airflow or leaks around the filter and reduces the effectiveness of the control for protecting miners from DPM. The optimal filter needs to capture DPM particles at a high efficiency while still allowing the needed airflows to prevent contaminated air from entering the miner’s breathing zone. Listak and Beck (2012) recommended velocities greater than 0.5 m/s for dust reductions of greater than 50%. However, airflows too high have been shown to reduce miners’ thermal comfort; Roghanchi et al. (2016) suggest the optimal velocity for thermal comfort is between 1–2 m/s. Thus, airflow over the miner should be limited to the range of 0.5 to 2.0 m/s. This current study presents the results from research evaluating the reduction of DPM concentrations, under the DCAC, when using a higher efficiency filter (MERV 16) to remove DPM from the DCAC airstream.

Feb 1, 2024