Search Documents

By B. Beatty

Discussion by B. Beatty This is a response to M.J. Hrebar's paper, which tracks in detail the highly productive stripping capabilities of modern large bulldozers at two separate installations. It proves the old adage "economies of scale" and quantifies the advantage of being able to move large loads of dirt over comparatively short haul distances by sliding rather than carrying the load. This discussion examines whether a bulldozer is the most efficient way of using this geotechnical principle. Case 1 - Study eastern US: Contour coal stripping application The energy consumption for the Case 1 mining method (eastern US contour stripping operation) shows the D11 averaged 117 L (31 gal) of diesel fuel per scheduled hour, and produced 333.3 bank m3 (436 bank cu yd) per scheduled hour (0.351 L/m3). Assuming 1 L (0.26 gal) of diesel fuel contains 10.4 kW-hr of energy, the unit expenditure of fuel energy for Case 1 Study was 3.66 kWh/m3. Another way of shifting this material is by using an overburden slusher (OS), as shown in Fig. 1. The OS as shown in Fig. I. The OS is electrically powered and consists of a manned low wall winch (LW ), a remote controlled (radio telemetry) highwall winch (HW) and a hoe. The winches operate to pull the hoe back and forth across the pit. The hoe carries load in the forward direction ahead of a rear mounted blade and returns empty. A spreadsheet (Lotus 123) simulation package, BOSSIM, models the OS operation on a load by load basis over a wide range of pit configurations. The geometry shown in Fig. 2 of the paper was modeled using BOSSI M and the results are summarized in Table1. Table 1 shows a LW with 150 kW (200 hp) and a HW of 120 kW (160 hp) installed power, towing a 15-m3 (19-cu yd) hoe, would accomplish the Case 1 stripping task at about the same scheduled stripping rate (D11=333 m3/hr or 433 cu yd/ hour, OS=342 m3/hr or 447 cu yd/ hour). It was assumed the winches in this equipment have an electromechanical efficiency of 90%. This gives an average electrical energy expenditure rate of 151 kW-hr, and a unit energy expenditure level of 0.44 kWhr/m-3(0.57 cu yd/kWh)-an improvement of 8291%- over the D11 alternative. The energy comparison illustrates the importance of using more efficient electric power if possible, ahead of the internal combustion engine, and delivering power from a fixed ground position rather than through a moving track system. Another important energy observation is the comparative action of the dozer blade and the OS hoe. The former implement continuously digs and spills as it works the load forward. The OS hoe digs the load until full, the blade then lifts due to the contained load pressure and a shear plane forms under the mass, enabling it to slide forward in a force reduced - transporting mode. Economic comparison Table 2 operating cost per scheduled hour and unit cost comparison follows a format used in Tables 2 and 3 of Hrebar's paper and compares Case 1 Study with the OS alternative. Drill and blast costs are kept constant in both cases, although when larger OS units are considered, it is expected these costs will reduce because bigger hoe sizes will permit larger rocks to be transported efficiently.

Jan 1, 1995

By Erling Stranden, Leiv Berteig

INTRODUCTION The measurement of the total activity of radon daughters in the air of mines has become a routine procedure in order to control the radiation exposure in miners due to the inhalation of these radionuclides. Normally the measured concentration is given in terms of total potential L-energy of the short lived radon daughters. The unit most frequently used is 1 WL (working level), which is defined as the potential a-energy of 1.3.105 MeV per 1 of air. The a-dose to the respiratory tract is, however, not proportional to the inhaled potential a-energy. In addition, the degree of equilibrium between the daughter products in air and the fraction of daughter products not attached to aerosol particles (the unattached fraction) must be known. Theoretical calculations of the equilibrium between daughters and the unattached fraction have been presented by different authors (Jacobi, 1972; Porstendörfer et al, 1978). Such calculations must take into account the plateout of daughters on surfaces, the attachment of daughters to aerosols and removal of daughters by the ventilation. The situation in mines will however be very complex and no single model will cover all situations. In most cases the radon and radon daughter concentrations will be described by a combination of different models. Domanski (1979) used the experimental results of Breslin et al. (1969) from uranium mines to relate the equilibrium between the individual daughters to the equilibrium factor, F. Once the equilibrium factor is known, this seems to be a useful approach to assess the individual daughter concentrations. The concentrations of radon and daughter products may vary considerably during the day. Seasonal variations are also frequently found. It is therefore important to have knowledge of the magnitude of these variations and of the factors having the strongest influence upon the concentrations. The unattached fraction of radon daughters in uranium mines was investigated by George and Hinchliffe (1972) and Raghavayya and Jones (1974). Mercer (1975) later modified the results of Raghavayya and Jones. Both these investigations indicated that the aerosol particle concentrations was the main influencing factor upon the unattached fraction. In this paper we will summarize the main results of a study on the radiological characterics of nonuranium mines. We will also discuss the correlations between the unattached fraction of the potential a-energy and the unattached fraction of the individual daughters, and between the equilibrium factor F, and the individual daughter ratios. More detailed discussions of this study will be published elsewhere (Stranden and Berteig, 1981 and Stranden and Berteig 1981 a). MATERIAL AND METHODS During 4 two-weeks periods corresponding to the seasons in the Norwegian mine where the highest radon daughter concentrations occure, the parameters listed in table 1 were studied. TABLE 1 Parameters measured during the study [Parameter Methods Radon Scintillation flask/Continuous ionization chamber Radon daughters Tsivoglou(1953)/Kusnetz(1956) Respirable dust Cyclone Unattached fraction Wire screen (Stranden and Berteig 1981) Atmospheric pressure Continuous baragraph Temperature and Continuous thermohygrograph humidity] At a fixed location, the radon concentration was measured continuously by a ionization chamber (Stranden, 1981), during these two-weeks periods in order to study short-time and seasonal variations. RESULTS Correlation between equilibrium factor and individual daughter ratios. The mean value of the equilibrium factor in all Norwegian mines measured during the last ten years was 0.46 with a minimum of 0.08 and maximum of 0.93 (Stranden and Berteig, 1981). The correlations between the equilibrium factor F, and the individual radon daughter/radon ratios were studied and the results indicated high correlations. In table 2, these correlation formulae are listed together with the correlation coefficients. TABLE 2 Correlation between the equilibrium factor, F, and individual radon daughter ratios [Formula Correlation coefficient RaA/Rn = 1.14 F 0.551 0.76 RaB/Rn = 1.00 F 0.940 0.99 RaC/Rn = 0.77 F 1.120 0.92]

Jan 1, 1981

By J. L. Coburn

The Huari-Huari ore body is located in Southern Bolivia, at an elevation of approximately 3,800 meters above sea level. The ore is a complex massive sulfide, slightly marmatitic sphalerite, in a fault fissure filled hypo- thermal vein in Paleozoic shales and quartzite-altered sandstone. The sphalerite has common associations with pyrite and quartz and is frequently intricately intergrown with stannite, chalcopyrite, and pyrrhotite. The sphalerite also contains numerous inclusions of pyrite, marcasite, galena, boulangerite, jamesonite, quartz, arsenopyrite, and cassiterite. A research program was undertaken to develop a flowsheet for the recovery of separate silver, zinc, and tin concentrates by selective flotation. Based on this experimental work and subsequent flowsheet development, engineering and construction of a 500 metric ton per day concentrator was undertaken. This paper describes the process that was developed for the Huari-Huari ore and the unique aspects of the Huari-Huari concentrator.

Jan 1, 1977

By Behrooz Abbasi, Seyedsaeid Ahmadvand, Thom Seal, Babak Azarfar, Bryan Ulrich

Hydro-Jex® is a new enhanced method for heap leach treatment with significantly higher mineral recovery. In this case study at the Los Filos Mine in Mexico, the Hydro-Jex operation is evaluated for heap leach stability. This is pursued by numerical modeling of the heap leach pad stability and well monitoring of the phreatic surface before and after the Hydro-Jex operation. Experimental and numerical results both indicate an improvement in mineral processing under the influence of Hydro-Jex. Numerical results show an insignificant decrease and a significant increase in stability during and after Hydro-Jex injection application, respectively. The integrity of the liner is maintained in both cases. The zonal injection pressure, operationally below the overburden pressure, is found to be negligible compared with the dimensionality of the heap, and stability of the structure is not exposed to any significant risk, even up to 25%above overburden pressure. Furthermore, heap leach factor of safety increases after Hydro-Jex application. This is attributed to breakdown of the water solution build-up and thus a decrease in the phreatic surface depth below the top of the pad. It is suggested that injection wells be drilled, based on thorough geophysical data, in locations where overcompaction of heap material results in water solution build-up and pore pressure enhancement. Compared with traditional heap leaching, the Hydro-Jex technique not only expedites mineral processing by increasing chemical kinetics extraction but also increases the stability of the heap by unclogging drains.

Jun 29, 2020

By J. R. Batista

Leachates from gold heap-leaching mines contain selenium concentrations as high as 2 mg/L. Previous studies report satisfactory selenium adsorption by activated alumina when using relatively "clean" drinking waters. However, the findings of these studies cannot be directly applied to the treatment of mine leachate where other ions compete for the alumina adsorption sites. This study evaluated the adsorption of selenium from a mine leachate to develop design parameters for full-scale activated alumina processes. The study revealed that 68% of the selenium in the leachate could be removed by alumina at pH > 5.0. Silica adversely affected the selenium adsorption capacity. At pH values < 4, silica was poorly adsorbed by alumina and selenium adsorption was improved.

Jan 1, 1994

By Daniel A. Wasson

A review of the history of boosters is given with examples of the prominent types that have been made commercially. The performance and design features of protected core boosters are discussed in detail. A new gel booster is discussed with its advantages to the mining industry. Booster size, hole configuration, performance and safety aspects are reviewed. Important features of boostering in above ground and underground blasting are related to an economic analysis. This presentation will cover different types of boosters commonly used in mining. However, for the purpose of this paper a few terms need to be defined to clarify the action of different parts of a priming system. Booster* - "Any unit of explosive or blasting agent to be used in a charged hole for the purpose of perpetuating or intensifying the initial detonation". Primer* - "A unit, package or cartridge&apos; of explosives containing a detonator or detonating cord which is used to transmit detonation to other explosives or blasting agents". Detonator - A device for initiating a detonation from a flame or a small electric current, the former being represented by a fuse cap and the latter an electric blasting cap.

Jan 1, 1981

By James Carroll, Lance Heyer

This paper describes the shaft design and construction for a 72-inch microtunnel under 14 active railroad tracks in Avondale, Louisiana. Initial shaft design for a deeper tunnel alignment considered secant piles with a jet grout plug. Final design for a shallower tunnel alignment included contractor input with support consisting of braced sheet piles with a jet grout plug. The authors further elaborate on jet grout implementation in very soft organic clay soils and the practical limitations of jet grouting. This paper emphasizes how all project participants worked together to utilize value engineering and alternative delivery on a unique tunneling project with a focus on temporary shaft support.

Jun 23, 2024

By Edward F. Oxford

The area described in this paper lies along the inner margin of the Coastal&apos; Plain in Twiggs County, near the exact center of the State of Georgia. Twiggs is one of four counties which produces approximately 75 per cent of the nationals output of kaolin used in the paper trade. In this vicinity the land surface is characterized by coastal plain hills with elevations ranging from about 250 feet, above mean sea level in the flood plain of: the Ocmulgee River to about 550 feet above mean sea level on the hill tops. Surface drainage in the area is southwestward to the Ocmulgee River, the tributaries of which have dissected the land surface exposing thick sections of the upper parts of the hills of Eocene (Ocala Limestone and Barnwell formation) limestone, sand, marl and clay, and in the lower parts of the hills Cretaceous (Tuscaloosa Formation) kaolin, kaolinitic clay, sandy clay, sand and, gravel. The contact between these two principal groups of geologic units is rather easil distinguished as the top of the kaolinitic beds. It is described in detail and mapped in published geologic reports for the area (LaMoreaux, 1946).

Jan 1, 1968

By D. C. Myntti

An open pit mining equipment maintenance program, in order to be successful, must have many active segments covering the full range of equipment selection, trained personnel, repair facilities, preventive maintenance programs, warehousing, interdepartmental cooperation, paperwork and effective communications. The mine maintenance program is required to protect company assets Which are units of equipment generating revenue. The program should result in reduced unscheduled equipment downtime, increased equipment productivity rates, and decreased unit operating costs. Current maintenance problems; maintenance effectiveness and future projections on equipment maintenance are discussed. Equipment maintenance is big business and the maintenance department is a full-time partner in the mining venture.

Jan 1, 1978

By O. A. Orumwense

The liberation of intimately disseminated impurities from the coal matrix often demands that the material be ground to a high degree of fineness. Similarly, some technologies for coal utilization require superfine particles (i.e., sizes less than ten microns). This implies additional costs for coal preparation plants due to the high energy and media costs associated with fine grinding operations. Besides, there are problems such as sever product contaminations due to media wear and impairment of the quality of coal. Hence, proper choice of grinding media type is important from the viewpoints of cost reduction and product quality.

Jan 1, 1993

By J. E. Murphy, L. A. Walters, F. H. Nehl, G. B. Atkinson

The US Bureau of Mines investigated the selective electrowinning of Ag and Au from cyanide solutions contaminated with Cu with the goal of decreasing the amount of Cu codeposited. Decreasing Cu codeposited will reduce refinery costs. Direct current was applied to the cell in pulsed and square wave voltages at 0.7 A h/150 mL of solution. Times tested for each cycle ranged from 1 to 10,000 msecs. Graphite, lead and stainless steel were evaluated as electrode materials. Square wave electrowinning at 70°C (158° F) gave the best separation of Ag and Au from Cu. Applying 2.5 V during the duty cycle, 0.0 V the rest of the period, a duty cycle of 10% to 30%, and a period of 100 msecs to 1000 msecs gave the following results: Ag concentrations decreased from 34 µg/mL to 0.1 µg/mL. Au concentrations decreased from 54 µg/mL to 0.2 µg/mL and Cu concentrations remained almost constant at 560 µg/mL.

Jan 1, 1995

By Jim Britton

Sustained elevated metal and coal prices in 2011 continued to drive mining projects across British Columbia. The province is the top producer of copper, exporter of coal and the only producer of molybdenum in Canada. The province also produces significant amounts of gold, silver, lead and zinc and more than 30 industrial minerals. The total 2011 value of solid metal production is an estimated $8.6 billion and the outlook for 2012 is positive. British Columbia is poised to bring several new mines onstream in the next few years. Construction continues at the New Afton and Mt Milligan copper-gold projects that are anticipated to be open in 2012 and 2013, respectively. The provincial Environmental Assessment Office indicates there are 26 mine proposals in process with three currently under review and 23 in the preapplication stage. The following text briefly describes 2011 metal and coal mining activities in the five regions reported on by the provinces? regional geologists (Fig. 1).

Jan 1, 2012

By B. Samanta

This paper highlights the use of an innovative mine production scheduling scheme for grade-control planning tasks that take into consideration grade-model uncertainty. The scheduling exercise has been carried out with the help of a multiobjective genetic algorithm (MOGa) for the production scheduling operations. The underlying motive behind the use of MOGa has been the generation of a set of pareto optimal solutions to meet the goals of the target-grade specifications for the considered multiple grade attributes. Several new concepts related to MOGa formulation, in particular the mutation operation and the convergence criteria of this algorithm, are proposed in this paper. The modeling of grade uncertainty into the scheduling outputs has also been incorporated through a set of conditional simulated grade maps. The proposed scheme of production scheduling operations has been applied for the grade-control planning operations in an iron ore mine to meet the targeted grade specifications of iron, silica and alumina, and a risk analysis has been performed to this end.

Jan 1, 2013

By V. Rajaram

The Metropolitan Water Reclamation District of Greater Chicago (MWRD) imposed a no-blasting specification (blasting is restricted to the construction shaft and shaft bottom or boot) on the Deep Tunnel project in 1988. This was prompted by numerous complaints from the residents in the vicinity of the project, and controversies experienced on previous projects from blasting the rock overlying the tunnel. This paper will describe the methods utilized by two major contractors who are driving 20 km (12.5 of tunnel along with drilling over 36 shafts under this restrictive specification. The impacts on design, construction, schedule, cost, and the environment are detailed.

Jan 1, 1991

By Eric Ohl

Due to the world&apos;s ever increasing minerals and energy demands, process plants have to cope economically with ever growing throughput rates. This trend has accelerated the development of high capacity vibrating screens. Screens with screening areas of 30 to 50 square meter (322 to 540 square feet) and width of 5.5 meter (18&apos;) are technically possible and are being used presently with great success. This paper will concern itself with the general aspects of large screen design, by using modern technology and the latest findings with regards to fatigue strengths relative to the laws of vibration. It also will investigate the technical and economical limits of such designs.

Jan 1, 1983

By James E. Myers

This study is a survey of the current "state-of-the-art" of commercially-available sonar tools to monitor the true shape of man-made cavities within the Hutchinson Salt of south-central Kansas. The work entailed ferreting out the available information, most of which is proprietary in nature; then examining actual existing conditions and arriving at a reasonable scientific evaluation of the method. Our studies were confined to one LPG field and two brine well operations in south-central Kansas. No field testing of any devices was performed, only questioning user firms, and studying cores, logs, and sonar surveys graciously made available by the companies we have contacted. Since these data are still somewhat proprietary, the company participants have asked that their company names be omitted from this presentation.

Jan 1, 1973

By Brian Ulrich

The majority of individuals involved in the mining industry can appreciate and under-stand that mining is an activity that is necessary to satisfy the very basic needs of society, and to assist in accommodating our ever-changing world. As the expression goes, ?if it can?t be grown, it has to be mined.? And at this point in time, society has granted the mining industry the right to go about the business of mining, with the general anticipation that the work will be carried out without causing undue harm to the environment or populations in and around the mining operation. The term ?sustainable development? is gaining momentum as a popular concept, and indeed it has become something of a catch-all phrase, but it is important that the idea behind the term is not cast aside as a nonsense buzz word, as it simply is an indication that development (e.g. mining) can be satisfactorily carried out with an eye toward stewardship of the environment and society. On Feb. 19, 2010, a round-table discussion (Roundtable 2010) on ?Strides Toward Sustainability in Mining? was hosted by Knight Piésold and Co. (Knight Piésold) at the Red Lion Inn and Casino in Elko, NV. Knight Piésold had local representatives (Bryan Ulrich and Steve Boyce), as well as representatives from other office locations (Cynthia Parnow and Rick Damiani from Denver, CO, and Rick Frechette from Tucson, AZ) to help facilitate the discussion. The meeting played host to 30 attendees from five states. Attendees included personnel from nine mining properties and various corporate offices. The majority of participants were people who are directly involved with environmental work on a day-to-day basis. Others were project managers whose jobs involve some level of environmental focus.

Jan 1, 2010

By L. M. English

In the past 30 years, the research arena has changed significantly in all fields, mining included. The relative representation of the topics of research, how the research is performed, and who has performed the research have all changed significantly over these decades. Although there are a lot of subjective ideas concerning these changes, and there is a fair amount of anecdotal "analysis," there has been no actual study of these trends to verify the facts. The period studied is divided into six five-year periods for the purposes of comparison. Some of the trends analyzed are as follows: ? Co-authorship ? Research areas ? Research sponsors ? Cooperative efforts

Jan 1, 1995

By W. K. Dressel

Over 2 million tons of steel furnace dusts are produced each year in the United States. Recycling of these dusts rather than disposal would conserve mineral resources, reduce land requirements for disposal, and decrease pollution. In addition to the iron content, the dusts contain appreciable amounts of zinc and lead. Removal of lead and zinc with simultaneous reduction of Iron oxide has been achieved by inert atmosphere roasting of carbon-containing pellets prepared from steel furnace wastes. High- and low-carbon wastes were blended to obtain mixtures with sufficient carbon to serve as a reductant during subsequent roasting. The mixtures were pelletized with the addition of bentonite and water, and the dried pellets were roasted in a stream of nitrogen at temperatures ranging from 900" to 1,150° C. Zinc and lead contents were reduced to the 0.1 percent level or less by roasting mixtures containing as little as 7 percent carbon for 1 hour at 1,100° C. ton metallization increases with available carbon content; 50 percent metallization is achieved with 7 percent carbon, 85 percent metallization with 12.5 percent carbon, and over 95 percent metallization when the pelletized mixtures contained in excess of 20 percent carbon.

Jan 1, 1973

By V. Claremboux

The transformation of raw iron ore into high quality steel can take place via several processes. A general consistent theme involves the upgrading of the iron ores via methods such as flotation and magnetic separation, the preparation of an agglomerate such as via pelletization or sintering, the smelting of the agglomerate into a high grade iron product, and the further refining of iron into specific steel alloys. Each of these steps admit potential for optimizations and alternatives, and the process overall is critical to meeting the world’s continuing iron demands.

Feb 1, 2025