Search Documents

By Justin Reed, Sara Bewley, Dwight M. Kinnes, Maryam Sadeghi, Ed Hart

This study compares wet gravity and dry magnetic separation for preconcentrating an allanite-rich rare earth ore from the Halleck Creek deposit. Material in the –300/+86 μm size range was treated to define a flowsheet that maximizes total rare earth oxide (TREO) recovery. The ore is dominated by feldspar and quartz, with hastingsite, an iron-bearing aluminosilicate. Because hastingsite’s density and magnetic response closely match allanite, it is difficult to reject using conventional methods. Two separation approaches were evaluated: MG12 spirals for gravity concentration and an Induced Roll Magnetic Separator (IRMS) for dry magnetic upgrading. MG12 spirals performed well in the rougher stage but provided limited gains when used as cleaners. When IRMS was applied as the cleaner stage, TREO grade and recovery improved substantially, showing that a dry magnetic cleaner circuit can effectively replace the wet gravity cleaner step. MG12 spirals remain suitable for highcapacity rougher duty, but dry magnetic separation delivers higher selectivity, simpler operation, and eliminates water use—offering a more efficient and sustainable preconcentration route in water-constrained environments.

Feb 22, 2026

By Rameshwar Sah, Somasekhar Pitchika, Akhil Singh, Seenivasan Rajiah, C. B. Dayanand, G. Balachandran

In the sintering of iron ores, the partial substitution of anthracite coal for coke breeze has been considered to be an effective way of reducing emissions and improvement in sintering properties. In the present study, the combustion characteristics of the anthracite coal and coke breeze were investigated and its influence on product sinter quality and sinter flue gases is being monitored. Pot trials are carried out with different coke breeze ratios, 0%, 40%, 50%, 60%, and 100%. It is found that as the percentage of anthracite coal is increased from 0 to 100%, the sintering time decreased from 24 to 20 min, and the productivity increased from 2.25 to 2.60 t/h/m2. Up to 60% anthracite coal substitution Tumbler index (+ 6.3 mm%), Product yield (+ 5 mm%), and fines generation (− 5 mm%) is found 62.29%, 85.17%, and 15.33%; moreover, hematite ( Fe2O3), magnetite ( Fe3O4), calcium ferrite phases ( CaFe2O4, CaFe3O5), and Silico ferrite of calcium and aluminum (SFCA) are major mineral phases found during microstructural analysis of product sinter. Keywords Sintering · Anthracite coal · Combustion rate · Productivity

Jun 2, 2022

By Stuart R. Cotterill

Open cast surface mining requires blast hole drilling with many interesting facets in order to achieve mine planning forecasts. Interestingly, no single method or combination of theoretical hypothesis of mining economics is right for all conditions. On occasion mine planners introduce a project with little or no regard to drilling and blasting. Generally, drilling and blasting costs are a significant percentage of total mine overhead. One such drilling and blasting method which can be utilized to reduce overall mine expenditure is inclined or angle hole drilling. One must bear in mind, that angle hole drilling per-se mill not reduce costs, unless a set of required circumstances is met. An attempt will be made to detail when conditions of the mine design criteria dictate the use of angle drilling.

Jan 1, 1984

By C. B. Queja

Flexible synthetic membrane liners have become a standard facet to copper and gold heap leach pad design. While gold heap leach operations have utilized most types of synthetic liners, copper leach operations have commonly only been lined with polyethylene. The objective of this study was to determine if there are any chemical reasons why other synthetic membrane types could not be used to line a copper heap leach facility. With engineered consideration, the flexible membrane liner under the ore pile serves two purposes. The first provides a near impermeable boundary which aides greatly in the collection of the metal laden process solution. The second advantage to the flexible membrane is the almost non-permeable barrier to benefit increased environmental awareness that has led to an increase in solution containment technology. The Environmental Protection Agency (EPA) has developed a compatibility test for solutions and membrane liners. The EPA Method 9090 is intended for use in determining the chemical effects of a solution on the physical properties of the flexible membrane liner material intended to contain them. Data from these tests would assist in deciding whether a given liner material is acceptable for the intended application.

Jan 1, 1995

By G. ALBORNOZ, S. Utili, A. AGOSTI, C. VALDERRAMA, R. PELL, N. Morales

The steepness of the slopes of an open pit mine has a substantial influence on the financial return of the mine. The paper proposes a novel design methodology where overall steeper pitwalls are employed without compromising the safety of the mine. In current design practice pitwall profiles are often planar in crosssection and the profile in between ramps especially tend to be planar and defined by a constant inter-ramp angle. Sometimes rock layers exhibiting different strengths require the inclination of the profile to vary with depth, but the inclination across each layer is usually constant. Here instead, a new geotechnical software, OptimalSlope, is employed to determine optimal pitwall profiles of depth varying inclination. OptimalSlope seeks the solution of a mathematical optimization problem where the overall steepness of the pitwall, from crest to toe, is maximized for an assigned lithology, geotechnical properties and Factor of Safety (FoS). Bench geometries (bench height, face inclination, minimum berm width) are imposed in the optimization as constraints which bind the maximum local inclination of the sought optimal profile together with any other constraints such as geological discontinuities that may influence slope failure. The obtained optimal profiles are always steeper than their planar counterparts (i.e. the planar profiles exhibiting the same FoS) up to 8 degrees depending on rock type and severity of constraints on local inclinations. The design of a copper mine is first carried out employing planar pitwalls, secondly adopting the optimal pitwall profiles determined by OptimalSlope. The adoption of optimal slope profiles leads to a 34% higher net present value and reductions of carbon footprint and energy consumption of 0.17 Mt CO2 eq and 82.5 million MJ respectively due to a 15% reduction of rockwaste volume.

Mar 2, 2022

By Jerry M. Riggsbee, John H. Weber

INTRODUCTION The Washington Metro is a 98 mile rapid transit system that will serve the District of Columbia, southern Maryland, and northern Virginia. The construction work herein described relates to Section B-1 of this system. The contract for this work was awarded by the Owner, The Washington Metropolitan Area Transit Authority, to a joint venture doing business under the name of Ball-Shea-Norair. The partners in this venture were Gordon H. Ball, Inc., Danville, California; J. F. Shea Company, Inc., Walnut Creek, California; and Norair Engineering Corporation, Washington, D. C. The bid price for the project was $33,741,524 with a contract duration of 910 calendar days. Notice to proceed was issued January 5, 1970. The present modified price for the work is $36,866,000 with completion anticipated in July 1974. (About 1,638 days elapsed time.) The work to be done consisted essentially of construction of 3,490 linear feet of cut-and-cover track with side platform, and 600 ft cut-and-cover arch shaped subway stations. Stations are located in Judiciary Square and Eighth & G Street, N. W., areas. Decking of excavation in street areas, maintenance of traffic and utilities, vent and fan shafts, underpinning of court buildings in Judiciary Square and the Smithsonian National Portrait Building, and an electrical substation were included in the contract. Stations were constructed of cast-in-place concrete.

Jan 1, 1974

By C. Bryce

Rhenium is primarily recovered as a by-product from molybdenum roasting circuits. However, rhenium is also present in copper heap leach solutions at very low concentrations and represents a potential new rhenium source. Freeport-McMoRan Copper & Gold has developed a new process using carbon adsorption followed by ion exchange or solvent extraction to concentrate rhenium from less than 1 ppm to 15 g/L. The product is compatible as a feed to an existing rhenium processing plant. A pilot plant operated at Freeport-McMoRan?s Sierrita mine has demonstrated the technical and financial feasibility of this new process.

Feb 23, 2014

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

"DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage organizations to work together, executing such risk assessments comes with challenges. This paper focuses on one trona mine’s experience in the development and implementation of a field level risk assessment program to help its entire organization understand and manage risk to an acceptable level. Through a transformational process of ongoing support and communication, Solvay Green River fostered a culture of trust and safety grounded in risk assessment, safety interactions, and hazard correction. The application of consistent risk assessment (RA) tools was critical to create a participatory workforce that not only talks about safety, but actively identifies energies that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s process of RA implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks. As discussed, consistent efforts to establish a participatory risk management program are worth the initial struggle to ultimately reduce incidents. INTRODUCTION Work-related health and safety (H&S) incidents often account for lost days on the job, contributing to organizational/financial and personal/social burdens [1-2]. Accompanying research demonstrates that risk and ambiguity around risk contribute to almost every decision that individuals make throughout the day [3-4]. In response, understanding individual attitudes toward risk has been unquestionably linked to predicting H&S behavior [5]. Although an obvious need exists to identify more comprehensive methods to assess and mitigate potential hazards, some argue that risk management is not given adequate attention in occupational H&S [6]. Additionally, research suggests that a current lack of knowledge, skills, and motivation are primary barriers to mitigating workplace risks [3-6]. Therefore, enhancing knowledge and awareness around risk-based decisions, including individuals’ abilities to understand, measure, and assign levels of risk to determine an appropriate response, is increasingly important in hazardous environments to predict and prevent incidents. This paper focuses on tailored approaches to field level risk assessment (FLRA), measurement, and common barriers to participating in such activities. The authors use a trona mine in Green River, Wyoming, as a case study to illustrate how the organization overcame widespread and site-specific challenges to implement a proactive risk management program. By discussing the mine’s tailored FLRA program, this case study contributes to the literature by first, providing examples of critical components that need to be in place to ensure successful risk management and second, context for continuous quality improvement that can foster a higher level of trust and empowerment on site."

Jan 1, 2017

By S. K. Sahoo, S. K. Sharma, U. K. Singh, G. S. P. Singh

This research focuses on the strata control issues in a Bord and Pillar depillaring working under the influence of dead load condition of voluminous and fragmented softcover of overburden dump material. It reports the modeling of a mine working through the FLAC 2D software under the Indian geo-mining conditions. The modeling results of an actual mine working under softcover were compared with that under the intact overburden condition to assess the influence of the soft overburden over the depillaring working. The modeling work involved progressive caving of the strata and the cyclic goaf filling following the modelsimulated occurrence of main fall and periodic caving. Mohr-Coulomb Failure criteria along with a simplified strain-softening (MCSS) model was used to study the failure and caving mechanism. Salamon’s compaction model was used to simulate compaction and resultant stress recovery in the goaf material. Comparison of the model findings was done in terms of load on supports, abutment stress, and convergence, apart from the stress redistribution and failure mechanism. The load transfer mechanism of the soft overburden was also studied for an overall understanding of the strata behavior in such workings.

Jun 16, 2020

By P. James

"INTRODUCTION Control of target stream acidity is widely used in MIW (mining influenced water). Tailoring pH (a measure of acidity) finds application for controlling key chemistry in both process and waste streams. Traditional lime addition for neutralization and precipitation is most often used but has high reagent costs and results in large amounts of mixed metal sludge requiring costly disposal. A new adaptation of BPS’s patented DEMET™ technology (Dynamic Electrolytic Metal Effluent Treatment) platform offers a potentially improved and “reagentless” alternative to traditional chemical addition for pH adjustment. Electricity rather than chemical addition utilized in BPS’s proprietary approach controllably tailors target stream pH. The method offers a simple, low-cost processing technique yielding cleaner treatment chemistry. BPS’s “green” approach may yield lower operating (OPEX) and life cycle costs and significant reductions (up to 50%) in sludge generation compared to conventional lime treatment. It can also allow new opportunities to generate revenue via selective recovery of valuable processing byproducts. Specific savings and revenues depend on the target site chemistries, details, and processing goals. A more detailed discussion of the process and its operational principles may be found in Reference One.[1] Here application of the BPS treatment to POx (Pressure Oxidation) leaching as an alternative to traditional chemical addition is examined. An example operation process flow for gold mining is considered.[2] Promising processing points for potentially replacing conventional processes with DEMET are noted. The possibilities for lowering OPEX costs, lessening sludge creation, and capturing various valuable byproducts and residuals are examined. Financial life cycle benefit estimates of the principal gains provided by DEMET application to the example operation are noted. Extension and generalization of the analyses to a wider range of scenarios is explored."

Jan 1, 2016

By P. E. Damon

An arsenal of isotopic techniques is avail-able that can date the full range of hydrothermal ore deposits. The following are prerequisites for ideal results: (1) Careful collection of samples that are related to the event in a field and process context; (2) Optical examination of the component selected for dating to be sure that it has not been altered; (3) Careful preparation of a pure component of the sample selected for dating; (4) Precise and accurate measurement; (5) Knowledgeable interpretation of the data with reference to decay systematics, properties of the component analyzed as well as the field context and thermochemical environment of the ore process.

Jan 1, 1992

By J. Baz-Dresch

A custom-designed shotcrete system, consisting of an 8-m3 (10-cu-yd) transit mixer and a shotcrete spray boon carrier, is used by a two-man crew to transport and place up to 25 m3 (32 cu-yd) of steel fiber reinforced, dry, silica fume shotcrete per 11-hour shift. Shotcrete is custom blended by a local supplier and delivered predampened. Mix design and quality control are performed with a computer program that develops and graphs a properly balanced mix based upon the materials sieve analyses.

Jan 1, 1992

By Vivek Priyadarshi, VIVEK KUMAR HIMANSHU, A. K. Vishwakarma, M. P. Roy, A. K. Mishra, RAVI SHANKAR

The nature and orientation of joints in rock strata affect the damage pattern under explosive loading. Most of the limestone deposits in India are found with severity of joints. Categorically, these joints may have variable orientations such as dipping out of the blast face, inside the face, horizontally or having strike parallel to the face. The damage pattern under the varying category of orientation will be different. Accordingly, a numerical model in Ansys-Explicit Dynamics was prepared to compare the damages of rock mass under different joint orientations. The physical nature of a joint reflects frictional and stiffness behaviour. Accordingly, the damages have been compared under bonded and frictional nature of joints. The output damage pattern from the model has been validated on the basis of blastability index proposed by Lilly. Different limestone mines in India show different nature of jointing in their rock strata. Accordingly, the blasting outputs from three different limestone mines, viz. Rawan limestone mine, Sagmania and Birhauli limestone mine and Injepalli limestone mine, have been compared along with their blast design parameters and the nature of joint. The comparative results show that the closely spaced horizontal joints support maximum in burden movement and rock fragmentation due to blast.

Nov 23, 2023

By T. P. Meloy

A methodology is presented for finding feasible or locally optimal designs in the class of homogeneous, countercurrent, processing networks performing two-component non-sharp separations. The advantage of the methodology developed here is that given a set of independent performance criteria (specifications such as network separation factor, beneficiation ratio or recovery), a feasible or locally optimal countercurrent network design meeting those criteria can be found in one step. In the methodology, graph-theory was used to explicitly obtain the exact network responses of specific countercurrent networks. These responses were used to formulate the linear recursion equations whose solution gives the expressions for the countercurrent network responses which are a function of the stage transfer functions for two-component, non-sharp separations. These expressions are also functions of the network variables n and c. These expressions, together with the set of independent design criteria, were solved simultaneously for n and c using the Levenberg-Marquardt algorithm for systems of constrained, non-linear equations. The network variables n and c embody the coded network design information which is used to find the feasible network design which satisfies the set of independent performance criteria.

Jan 1, 1994

By Ali Behrad Vakylabad, Esmaeel Darezereshki, Babak Koohestani

As a by-product of the steelmaking industry rich in iron and zinc, electric arc furnace dust (EAFD) landfill disposal is restricted in many countries due to the metal lixiviation risks. Several approaches have been examined to recycle or reuse EAFD. Hydrometallurgical methods mainly include the preparation of pregnant acid leached solution (PLS) using inorganic acids followed by selective metal recovery using different methods. We herein proposed a hydrometallurgical process initiated by acid leaching and finalized by thermal treatment to produce nano-ZnO from EAFD. At the condition of this study, only 67% of zinc was leached by sulfuric acid from EAFD into PLS while 98% of surplus leached iron was removed through precipitation by sodium hydroxide. Additional purification of iron removed PLS was accomplished using di-2 ethylhexyl phosphoric acid to extract Zn+2. The addition of ammonium hydroxide to purified PLS provided (Zn(OH)2)3(ZnSO4)(H2O)5 as the final precursor for nano-ZnO that ultimately transformed to nano-ZnO (60 ± 6 nm particle size) at 850 °C. The achieved results were scrutinized through various tests and analyses including TEM, XRD, SEM, EDS, FTIR, and TGA.

Mar 10, 2021

"One of the major issues that the Rare Earth Elements Mining Industry has to deal with is the legislation vacuum that exists in many countries around the world. Among these, are countries which have long history and tradition in mining. In many cases the lack of direct legislation for REE mine management as well as for other potentially polluting industries can be a barrier to sustainable development. Moreover, the case of lax legislation in China has led to environmental pollution problems and extended smuggling of rare earth elements. This paper looks into the current regulatory status on the mining of REEs, identifies the loopholes and suggests some elements for a new global legislation framework for sustainable development in the REE mining industry. The setting of this regulatory framework will be in line with the present and future challenges of the rare earths market as well as with the policy strategies that are defined internationally. The aim of such a legislative framework will be to strengthen the global rare earth elements supply chain, appease social concerns and ensure the preservation and conservation of the environment. INTRODUCTION The general public received their first introduction to rare earth elements (REEs) in 2010, when the previously inconspicuous commodities became the subjects of front-page headlines. It was when China created a furore in global high-tech markets after imposing an embargo on Japan following a minor marine dispute (Barakos et al. 2015b). Soon enough the Chinese embargo was extended on REE export restrictions all over the world and thus aroused concerns to many countries over potential supply disruptions. The world had suddenly realized that these wonder materials underpin products that they care about. Governmental and industry executives, policymakers and material scientists voiced concerns and conducted numerous reports stating the situation and the risks of a supply crisis. The price spike of 2011 intensified the crisis and the public turmoil, yet the drama did not last for long as the prices declined significantly in 2012. Nevertheless, the world was nonplussed by the fact that China has the total control of the market with more or less the 90% of the global production. More potential entrants became interested, thus initiating an exploration boom during the recent years that has resulted in a significant increase in known global REE reserves that could have potentials for exploitation."

Jan 1, 2016

By S. Pollak, J. Rickard

The Long Baseline Neutrino Facility Far Site in Lead, South Dakota is currently under construction and involves drill and blast excavation of the largest and deepest caverns in North America. This paper will review how the geotechnical risks are being managed through careful consideration of excavation sequence, completion of exploratory pilot tunnels, implementation of a robust instrumentation and monitoring program, and validation against the design. Aside from having a cross section of 5,900 square feet and being situated at a depth of one mile, the caverns also employ a unique permanent rock bolt solution which underwent a significant pre-production pull testing program involving varying installation methods and being subject to blast vibrations. The behavior of the schistose rock mass and performance of the ground support are being continually monitored throughout the construction phase.

Jun 13, 2023

By M. S. Enders

The McDonald deposit is a volcanic-hosted epithermal gold resource that is estimated to contain 251,000 kg of gold in 375 Mt of ore at an average grade of 0.7 g/t gold. Phelps Dodge exploration geologists, working for the Seven-Up Pete Joint Venture, discovered the deposit in 1989. By the end of 1992, 494 drill holes for over 113,000 m of drilling, bulk sampling, soil geochemistry, geophysics, metallurgical testing, engineering, and environmental studies had been completed to support feasibility studies. The discovery of McDonald required vision, persistence, and commitment of everyone from the geologist on the drill rig to the senior management of the company.

Jan 1, 1995

By K. L. Kayler

The Bardon Trimount, Inc. stone quarry in Ashland, Massachusetts was the recent subject of a quarry closure review report. The quarry produces aggregate using standard drilling and blasting techniques. Stone is processed at an on-site plant. Noise monitoring data collected during the closure review indicate that the quarry generally operates within the quiet range. There is a decrease in noise while the quarry is not operating. Levels of dust associated with the quarry are low. Unpaved roadways are the greatest contributors of fugitive dust associated with the mining operation. The quarry cannot be seen from any homes within the town of Ashland, except during the winter months. The visual impact of the quarry on surrounding properties is minimal. Further quarry development is likely to reduce visibility of the quarry from some areas.

Jan 1, 1995

By T. W. Turk

Iron Mountain Mines, Inc., (IMMI) ore de- posits are located in the southeastern portion of the Klamath Mountains in the West Shasta copper/Zinc Mining District in Shasta County (Figure 1). The original massive sulfide ore deposits totaled 22,895,000 Mt (25 million st). The remaining ore deposits contain 12,875,000 Mt (14,183,000 st) of proven massive sulfides and 2,769,000 Mt (3,050,000 st) of proven gossan deposits. The addition of magnetite deposits and tailings (now marketable) brings the total of proven and probable reserves to 20,433,000 Mt (22,508,000 st). The massive sulfide ore bodies are generating a natural flow of acid mine water which has been slowly leaching minerals out of these deposits. This flow varies in volume, depending on rainfall, and contains variable concentrations of copper, zinc, iron and precious metals. This mine water has been treated for the past 50 years at the mine site to remove copper. The treatment process, utilizing scrap iron precipitation, continues at a production rate of approximately 54,430 Kg (120,000 pounds) of copper precipitate annually.

Jan 1, 1986