Search Documents

It is widely accepted that particles stabilise flotation froths and that stable froths result in improved flotation performance. Predicting the effect of particle addition on froth stability is, however, challenging. Dynamic surface tension measurement using maximum bubble pressure presents an attractive technique to investigate the effect of surfactant and particles at the air-water interface. The range of bubble lifetimes that can be studied (typically 0.1 to 60 s) is analogous to variations in air rate in flotation cells, and the corresponding changes in surface tension give an indication to the diffusion and adsorption rates of particles at the interface. In this paper, we use dynamic surface tension measurements to investigate the effect of particles on bubble surfaces at the microscale and link this to bulk froth stability measurements carried out using a froth column. Using the maximum bubble pressure method, the results show that the addition of particles results in lower surface tension, both at the dynamic (i.e. short) bubble lifetimes and towards equilibrium (i.e. 60 s bubble lifetime). This corresponds with the bulk froth stability measurements, where the three-phase system yielded more stable froths than the surfactant only system. Furthermore, increased particle loading at the air-water interface, whether through higher surfactant concentrations or lower air rates (longer bubble lifetimes), gave lower surface tension and higher froth stability. This demonstrates the link between bubble loading and froth stability. It is proposed that the maximum bubble pressure technique can be used to predict froth stability for two- and three-phase systems, enabling the effect of particle loading to be accounted for and quantified. Moreover, the technique has the potential to allow rapid determination of particle and surfactant diffusion at the air-water interface and prediction of the corresponding effect on bulk froth behaviour.

By Michael Day, Paul Kos, Scott Brinton

A hydrogeologic characterization and impact analysis was performed for a proposed quarry at the Hitch Rack Ranch located in the Little Turkey Creek watershed southwest of Colorado Springs, Colorado. Continuous multiple channel tubing, nested piezometers, stream flow measurements, and mapping of known seeps were used to define the three-dimensional potentiometric distribution and areas of groundwater recharge and discharge. Water balance considerations, mass balance calculations, and potentiometric response to earth tides and barometric fluctuations confirmed that the granite fracture system in the ridge area of the proposed quarry has an extremely low bulk hydraulic conductivity resulting in minimal groundwater discharge to sustain the baseflow of Little Turkey Creek. The Little Turkey Creek valley forms the major conduit for groundwater flow exiting from the upper part of watershed underlain by granite. This conclusion has significant implications with respect to mine planning to minimize projected impacts to the hydrologic system and preserve this recharge component to downgradient Denver Basin sedimentary deposits.

By S. Schina

Part of the Imittos Western Peripheral Motorway in Athens is the twin road tunnel in the vicinity of American College, with 20m excavation diameter. In the paper, the environmental and other requirements, the geometry and the geological – geotechnical characteristics of the rock formations in the construction area are given. Information regarding the modeling and analysis methods that are used for the design of the temporary support, the final lining and the wedge and slope stability analysis is described thoroughly. Finally, the results of the analyses are compared with these of measurements and general remarks during the construction of the tunnels.

Jan 1, 2001

By David Young

This paper presents tunnel design considerations for the SR75/282 Transportation Corridor Project in Coronado, California. The project is managed by the City of Coronado in cooperation with Caltrans and the US Navy and may include a one-mile long twin-tunnel section with two options: a 36.5 foot diameter twin-bored tunnel or a twin cut-and-cover box. The alignment crosses the Coronado Fault, and design provisions were needed at the fault crossing to maintain life safety and prevent rapid inundation of the tunnel in the event of fault rupture. These provisions are discussed along with considerations related to liquefaction and ground shaking. The project is currently in the planning stage with construction to start around 2012.

Jan 1, 2008

By Xun Zhang, Hang Qiu, Andrea R. Gerson4, Shaomin Lei, Yubiao Li, Yu Meng, Zhenyu Pei, Min Lin

Efficient separation of trace muscovite from the surface/interface of quartz grains was accomplished during oxidizing calcination and catalytic pressure leaching of the hydrothermal quartz. Experimental results suggest that 98.97% or more of the muscovite was separated when quartz sand was calcined at 900 °C for 5 h and then leached by hydrochloric acid and ammonium chloride solutions as substitutes for leaching agents containing fluorides. The chemical processing techniques show high selectivity in purifying quartz sand by transforming mineral muscovite into active structures during oxidizing calcination, and then dissolving the active substances during catalytic pressure leaching

By J. Kern, T. F. Torries

Identifying high value areas of unmined coal when large quantities of coal are available relative to annual markets is difficult because of the uncertainty of when the coal is to be mined. A GIS based methodology developed to value reserve coal in a producing coal region for the purpose of ad valorem taxation also identifies high value areas for mining investment. The methodology is unique in that it accounts for most mining, environmental, and market factors to determine when specific properties are to be mined. The methodology and data base are useful for directing regional exploration and acquisition activities toward most favorable areas.

Jan 1, 1999

From a vast army of workers to gargantuan machines to immense volumes of material being moved, almost everything about the Port of Miami Tunnel (POMT) project points to tunneling on a massive scale. Almost.The star of this underground and underwater show is a Herrenknecht tunnel boring machine (TBM,) nicknamed ?Harriet? by a local Girl Scout troop. With her 12.9-m- (42.3-ft-) diameter cutting head and a total length of 139 m (457 ft), Harriet is boring through thousands of cubic meters of clay, dirt and sand, which is often mixed with coral and other materials, to create two 1,280-m (4,200-ft) traf?c tunnels connecting Watson Island and the Port of Miami (Dodge Island) beneath Biscayne Bay, FL. But in the midst of all of the oversized equipment and machines, a strong contender for the best supporting nod goes to a relatively tiny machine: the Brokk 400. Bouygues Civil Works Florida crews are using the compact, remote-controlled and electric-powered machine to excavate five cross passages between the twin traffic tunnels. The pas-sages will be essential to the safety of people who drive their vehicles under the bay every day.

Sep 1, 2013

By Lawrence M. Gochioco

One of the best kept technology secrets in U.S coalmining history involved a robust coal geophysics program used by a local coal company to detect and map various geologic anomalies and man-made structures ahead of mining for nearly 15 years. Several original mine plans were changed as a result of findings from two-dimensional (2D) and three-dimensional (3D) seismic data. They indicated the presence of geologic anomalies in reserve areas that could adversely impact future mine development and longwall production. By combining the surface seismic and exploratory drilling methods, the coal company learned how to properly leverage its risk by gathering a lot of useful subsurface information before making major commitments.

Jan 1, 2005

By Carmel Bofinger, Maureen E. Hassall, David Cliff, Eric Stemn

e Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

By Carmel Bofinger, Maureen E. Hassall, David Cliff, Eric Stemn

e Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

By S. K. Kawatra, K. J. Shoop, T. C. Rao, T. C. Eisele

This study investigates the use of a horizontally- baffled column (7.6 cm inside diameter by 344.2 cm high) to reduce the ash content of a high ash bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feedrate, reagent dosage, and feed quality, and to compare its performance with a conventional column installation in an operating plant. In this paper, the results of this investigation will be reviewed and discussed.

Feb 24, 1997

By Antti Porvali, Vivek Agarwal, Mari Lundström

Hydrometallurgical recovery of rare earth elements (REE) from NiMH battery waste can be performed using sulfuric acid leaching followed by selective precipitation as double salt (REENa(SO4)2·H2O) by adding Na2SO4 as a precipitating agent. The formed double salts can then be further converted with NaOH solution to form REE hydroxides. However, present literature has paid little attention to how to minimize the consumption of reagents in this recovery process. In the current study, a process model was built using HSC Sim software, and metamodeling of the simulated flowsheet was conducted with the design of experiments (DOE), after which the basic functionality of the flowsheet was verified by experimental work, starting from sulfuric acid leaching of spent batteries. As the process is based on chemical circulation internally in the process, the objective was to investigate the accumulation of the elements in solution, specifically Na+ , K+ , SO4 2− ions and impurities liberated in the NaOH conversion step. It was found out that metamodeling could be utilized in obtaining first estimate of the process behavior, prior to any experiments. Flowsheet functionality with circulated solution was confirmed, obtaining at best 96.9% La recovery.

By Antti Porvali, Vivek Agarwal, Mari Lundström

Hydrometallurgical recovery of rare earth elements (REE) from NiMH battery waste can be performed using sulfuric acid leaching followed by selective precipitation as double salt (REENa(SO4)2·H2O) by adding Na2SO4 as a precipitating agent. The formed double salts can then be further converted with NaOH solution to form REE hydroxides. However, present literature has paid little attention to how to minimize the consumption of reagents in this recovery process. In the current study, a process model was built using HSC Sim software, and metamodeling of the simulated flowsheet was conducted with the design of experiments (DOE), after which the basic functionality of the flowsheet was verified by experimental work, starting from sulfuric acid leaching of spent batteries. As the process is based on chemical circulation internally in the process, the objective was to investigate the accumulation of the elements in solution, specifically Na+ , K+ , SO4 2− ions and impurities liberated in the NaOH conversion step. It was found out that metamodeling could be utilized in obtaining first estimate of the process behavior, prior to any experiments. Flowsheet functionality with circulated solution was confirmed, obtaining at best 96.9% La recovery.

By H. A. Taylor

Graphite is elemental carbon that crystallizes in the hexagonal system as six-sided platelets. It occurs naturally and is mined. And it can be made artificially from petroleum coke in the form of shapes (electrodes) and powders. The market for most kinds of graphite in most end-uses was good in 2004. The 2005 graphite market looks positive. The major graphite prices, as given in Industrial Minerals, remained unchanged throughout the year. The preliminary 2004 U.S. Geological Survey (USGS) prices for natural graphite showed almost no change for crystalline flake. They were $600/t ($544/st) in 2004 and$622/t ($564/st) in 2003. Mexican amorphous graphite was almost unchanged at $150/t ($136/st) in 2004 from$152/t ($138/st) in 2003.

Jan 1, 2005

By S. M. Flaherty, R. E. Scheffel, A. Guzman

Geochemical conditions within a leaching operation are heterogeneous. This variability arises mainly from hydrological controls imparted by physical characteristics of the ore and by heterogeneous metallurgical properties at the rock-fragment and industrial heap scale. The resulting chemical conditions are responsible for stratified mineral recovery, non-uniform extraction and prolonged leach cycles. This paper presents field data from a sulfide-leaching operation which clearly demonstrate the impact of chemical heterogeneity on metal recovery and the potential use of modern measuring techniques to facilitate operational monitoring and decision making for optimization of leaching operations.

Jan 1, 2006

By J. Drelich, M. Pawlik

An improved experimental procedure to measure contact angle has been consolidated with coal surface preparation involving polishing with abrasive paper, alumina powder, and a cloth, followed by ultrasonic and mechanical cleaning. Specifically, the captive-bubble measuring technique has been compared with the sessile-drop technique and the former has been recommended for the examination of the hydrophobic properties of coal surfaces. Results of the research program, which is currently under way, on the examination of the effect of the nature, amount, size, and distribution of mineral inclusions in coal, on its wettability are briefly reviewed.

Jan 1, 1999

By J. Davies

This paper describes the successful management and construction of the 5.18 m (17 ft) diameter, segmentally lined, North Dorchester Bay CSO storage tunnel in Boston, MA. This 3,300 m (10,830 ft) long tunnel was mined through variable soft ground with only 6 m (20 ft) of cover, using an earth pressure balance tunnel boring machine. These extensive data collected from the projects unique automated and internet accessible geotechnical and TBM monitoring system, will be examined and used to explore the relationships between geological conditions, TBM operating parameters and measured settlements. The paper will also discuss the use of screw revolutions as an indicator of muck volume.

By K. J. Stanaway

Major world ilmenite and rutile accumulations reveal similar regional geology and Proterozoic age deeper crustal source rocks. During crustal collision titanium crystallizes as ilmenite and rutile at buried sites of high pressure and temperature rock metamorphism. Hydrothermal activity can convert titanium minerals to rutile, but titanium migration and enrichment seem only local. Many melts crystallize rocks with iron-titanium oxides in solid solution, but titanium enrichment at economic scale takes place in basic intrusive melts often associated with anorthosites and charnokite. Sedimentary placer enrichments have formed since the Proterozoic with water-resistant ilmenite, and rutile segregating by gravity from quartz sands deposited from flowing water. Placers have residual, alluvial, strand and shallow marine variants. Time, organic acids, and sand permeability play lead roles in the leaching of iron from ilmenite during weathering and diagenesis.

Jan 1, 2005

By R. J. Lytle

INTRODUCTION Prior to excavation in soil and rock, it is useful to know the subsurface structure. This is important information both for safety and for equipment scheduling reasons. It is useful to know whether parts of the subsurface might be potentially troublesome or of different character than is generally thought present. By using geophysical probing, it is possible to infer the location and size of these unusual regions. The ground structure is commonly estimated from core samples taken from boreholes. These cores give a detailed knowledge of the structure in the borehole. However, knowledge of the structure exterior to the borehole can only be extrapolated from core data. By using seismic and electromagnetic cross-borehole geophysical probing, remote probing can be used to sense the region exterior to boreholes. A recent advance has significantly improved the state-of-the-art for defining the ground structure between boreholes. This new procedure utilizes large amounts of data and provides a detailed picture of the subsurface. The data processing algorithms used are similar to those in medical imaging of the human body using x-rays, a science called x-ray tomography. This imaging of the ground is called geotomography, which is a shortened acronym for geophysical tomography. Several examples of geotomography applied to imaging ground structure are presented. Our approach has been to probe the ground with electromagnetic and seismic waves. We map the region of interest with signals transmitted between multiple source and receiver pairs lowered in boreholes on opposite sides of the region (Figure 1). The received signals vary according to the transmission properties of the media

Jan 1, 1979

By Steve Skelhorn

Edmonton South LRT is the latest expansion of the Subway system in Edmonton, Alberta, Canada: Consisting of twin 5.8m segmental lined tunnels, 280m long, driven by a Lovat EPB machine. The key challenges were as follows. A 6% downhill grade. Tight radius curves of 250m.Overlying structures within 3m of the tunnel. Strata consisting of sand above the water table, glacial tills and bed rock below the water table. Located within The University of Alberta Campus and adjacent to a hospital. Northern Alberta climate with winter temperatures routinely falling below—minus 30 degrees Celsius. This paper provides a case history and outlines the challenges involved in completing this project.

Jan 1, 2005