Search Documents

By Willard C. Lacy

INTRODUCTION A program to insure adequate talent for development and management of our mineral resources entails two equally important and interrelated aspects: 1) attracting and retaining promising student talent, and 2) providing a first-rate education for those entering careers in mineral science and engineering. Manpower shortages have eased in many areas of engineering, particularly in those areas dependent directly or indirectly upon government contracts in space and war programs. However, in the minerals industry the needs still remain critical. As increasing concern over preservation of the environment has developed, the political and social reaction was to seek out major offenders, to look for "whipping boys" -- and the mineral industry was, and had been, an offender. It was there for everyone to take pictures, it couldn't be covered up, and the Department of the Interior lashed away in the beautiful and popular brochures: Quest for Quality, The Third Wave, The Population Challenge, and Surface Mining and Our Environment (Ravaged Land). The Sierra Club, the Field and Stream magazine, TV, and daily news media added their lashes. In the minds of our social-conscious youth the mineral industry took on the image of "exploiters" of natural resources; "polluters" of streams, lakes, and the atmosphere; "despoilers" of wilderness areas and scenic beauty -- a plague to combat, rather than an exciting challenge that entailed exploration of the remote, conquering of the primitive, and developing of the undeveloped. Enrollments declined and many traditional mineral engineering curricula were abolished or Integrated into other stronger engineering departments to meet student-faculty ratio requirements.

Jan 1, 1971

By John R. Marks

Introduction An engineer is a builder and a problem solver. He uses knowledge of the properties of matter and energy to furnish the needs of society. Engineers form the bridge between scientific researchers and the general public, most of whom are technologically illiterate. Mining, metallurgical, and petroleum engineers extract minerals from the ground and process them into usable forms. Then, other engineers further process them into society's needs. Minerals engineers deal with more uncertainty than other engineers. Each ore deposit has its own personality and each ore is metallurgically unique. Minerals engineers, therefore, must be flexible, often applying larger safety factors and contingencies than other engineers, and frequently functioning as a jack of all trades. A minerals engineer can work in coal, oil, oil shale, base metals, ferrous metals, precious metals, industrial minerals, strategic minerals, or in exploration. Other mining jobs include banking and financing, education and research, marketing and sales, and government. As a minerals engineer, you may be among the first to work on the ocean floor or the moon. College Preparation A difference between college and industry is the type of problems to be solved. A typical college problem has an exact answer derived from given information. An industry problem is more apt to have a solution chosen from a number of alternatives. Information required for the solution is not given. It must be measured, calculated, looked-up, estimated, or otherwise derived. Solutions involve trade-offs, economics, and human factors, as well as application of physical laws and theory. When a college problem is answered, you move on to the next one. In industry, however, the headaches may just be starting with the implementation of the solution. Students often complain that they see little use for the theory they are learning. This is valid. A good professor will link theory and practice. Another difference between college and industry is the price of failure. In college, you can make a half-hearted effort in an assignment and take your C or D. On the job, however, poor engineering results in potentially effective projects being rejected and unsound projects being undertaken. Poor performance results in cost overruns, schedule holdups, oversights, disgruntled employees, irate bosses, unsafe structures, and unreliable systems. The costs are time, money, and possibly lives. The student pays the university for his work - not the other way around. So the rewards for good schoolwork often seem nebulous. But education must be viewed as an investment. Working for good grades will help you think better, learn more, receive better job offers, and perform more effectively on the job. There is no substitute for hard work. Avoid taking the easiest electives. If you desire a more liberal education or dislike rigorous physical sciences, mathematics, or engineering courses, change majors. Remember, you are training to be an engineer, not a computer programmer or market analyst. At least one summer of industry employment is necessary for minerals engineering students. The sooner you gain actual experience, the sooner you will know whether to change majors. Most large companies hire students during summer. It is best to send out applications around Christmas break. First and second year students usually work as laborers. Upper-classmen may work as engineering technicians. Students must sometimes choose between returning to a company at a higher position or trying a different company at a lower position, for more varied experience. Both alternatives have advantages. Do your best on these summer jobs. The company is watching. If you do well, the chances are good you will get a job offer when you graduate. Good references are important when you begin job hunting. Interviewing occurs near the end of your school career. The standard procedure is to send your resume with a cover letter to each company you are interested in. The resume for a graduating engineer with little experience need not exceed one page. The cover letter must be written for the individual company.

Jan 2, 1985

A viable mineral economy requires availability of economic deposits, the ability to exploit then, and protection of the public interests. The natural tendency for each party to consider only its legitimate self interests can lead to delays or deadlocks. The paper presents several viewpoints aimed at opening each party's mind to the ideas of others in the hope that negotiations might be more reasonable and rapid for the benefit of all concerned.

Jan 1, 1979

By H. Askari-Nasab, B. Osei, K. Awuah-Offei

The U.S. coal mining industry consumes approximately 142 billion kWh/a of energy. The U.S. Department of Energy estimates that the industry’s annual energy consumption could be reduced by 49%. This constitutes nearly $3.7 billion of potential savings on coal production costs at 5.3¢/kWh of energy. Additionally, with climate change regulation on the horizon, any benefits from energy savings in the near future are compounded by associated reductions in CO2 emissions. Research indicates that operating conditions significantly affect energy efficiency. Modeling and simulation have been shown to be a cheap and reliable means of evaluating the effects of process interactions and operating conditions. The goal of this work was to apply stochastic process simulation to model the energy efficiency of a typical truck-and-shovel mining system and use the model to evaluate production strategies to improve energy efficiency. The research team conducted energy audits of truck-and-shovel overburden removal and used the results to develop regression models describing truck and shovel fuel consumption. The team then built a stochastic simulation model of the truck-and-shovel overburden removal operation and used it to assess a variety of improvement measures by simulation experimentation. Valid fuel consumption models for shovel loading and truck haulage have been formulated, based on the energy audit results. Valid stochastic process models of truck-and-shovel operations have been formulated to study energy efficiency. The following strategies, in decreasing order of impact, provide the most energy savings for truck-and-shovel overburden removal at the mine: (1) shorten haul roads, (2) increase shovel capacity and (3) increase shovel utilization through optimal truck matching. Additional data will be required to adequately describe operator effects on energy efficiency.

Jan 1, 2011

By Jr. Winters

The United States continues to be the largest producer and consumer of copper in the world. Table 1 on the following page shows several production statistics for 1974, the most recent year which the non-communist world copper industry might consider a good year, and for 1976 and 1977. In 1974 an estimated 24 percent of the non-communist world's newly mined copper was mined in the United States, and. 87 to 89 percent of that was from the western porphyry coppers. In 1976 U. S. new mine production was down to 22 percent of the non-communist world's newly mined copper, and the percentage of U. S. new mine production supplied by the porphyry coppers had risen to 89 to 91 percent. In 1977 the statistics remained the same as in 1976. U. S. porphyry copper production represented about 65 percent of U. S. refined copper consumption in 1974, rose to 75 percent in 1976, and dropped back to 61 percent in 1977 as imports of foreign copper into the United States began to swell.

Jan 1, 1978

By Jack C. Haptonstall

The Tayoltita Unit of Minas de San Luis, S. A. is situated in an isolated corner of the state of Durango, Mexico. The ore deposits in the region were first worked by Indians, but by 1757 the Spaniards had discovered them, and the first systematic exploitation of the mines commenced. By the early 1900's most of the mines had been acquired by American interests, and the San Luis Mining Company was organized. The modern period of exploitation, uninterrupted for the last 74 years, began. In 1962 the company was fully "Mexicenized" in compliance with the modification of the mining law, and the name was changed to Minas de San Luis, S. A. Tayoltita continues as one of Mexico's most important silver and gold mines. The ore is extracted in en extensive underground operation, mining epithermal fissure veins by selective methods. The ore is milled and treated in an efficient counter-current cyanide plant, where 95 % of the silver and 96 % of the gold is recovered. Current annual bullion output is 55,000 kg (1.7 million troy oz) of silver and 1000 kg (31,000 troy oz) of gold from milling 165,000 try (181,900 stpy). Rough, 33-kg (1000-troy oz) bullion bars are smelted at the mine, shipped by air to Mazatlan, Sinaloa, and are thence sold to the Met- Mex Peñoles smelter in Torreon, Coahuila. Ore reserves, blocked by very conservative methods, are currently at 540,000 tons (595,000 st). Ore reserve grade is 425 g of silver and 6 g of gold per ton (12.4 troy oz Ag and 0.18 troy oz Au per st).

Jan 1, 1976

By T. N. Moore, E. M. De Souza

J. Dasher Regarding the March 1991 ME technical paper by De Souza and Moore: For more than a decade since my February 1981 article on how to use modern metric, which SME-AIME had decided to do, I have monthly pointed out metric errors to the editors. In part, I do this because there has been no action to allow editors to fix figures and tables or to allow them to require authors to do so. The latest resulting atrocity provokes this discussion of vibrating drill handle units being stated in decibels. Reply by T. Moore We have read the discussion of our paper by Mr. Dasher. Our reaction is one of surprise and incredulity. It would seem that Mr. Dasher takes exception to the use of the decibel scale to present vibration acceleration data, and the use of hertz as the unit for frequency. The basis for his objection to the decibel appears to be that it has no dimensions (which somehow invalidates its use), that it is "non-metric" and, finally, that it is parochial (of limited or narrow scope). His objection to the use of the term hertz is not stated, but we will assume that it stands condemned as "non-metric" and parochial. Obviously we disagree with Mr. Dasher's views and will now outline our reasons. Although the decibel scale originates from transmission line theory and telephone engineering, it is also at present widely used, not only in the fields of electronic engineering and acoustics, but also in the area of vibration. The original definition of the decibel (dB) was based on power ratios: dB = 10 log 10(W/W0) where Wo is a reference power. However, as the power measured across a given impedance is related to the square of the force acting upon this impedance, Z, a more commonly used definition is: [2 dB = 10 logF /Z) = 20 log F/F 10\ F0 2 /Z(0)] where F and F0 are the r.m.s. values of the forces. Now, if the measurements are related to one and the same impedance, the decibel notation in the form of 20log10(X/Xo) may be used as a convenient relative magnitude scale for a variety of quantities. Thus, X may, for instance, be an r.m.s. displacement, velocity or acceleration. It is only required that XD always be a reference quantity of the same type as X. That is, when X represents an acceleration, then X0 represents a reference acceleration. This is the formulation used in our paper. This was not an arbitrary choice on our behalf but reflects standard practice as specified in the International Standard ISO 5349-1986(E) Mechanical Vibration - Guidelines for the Measurement and the Assessment of Human Despite the metric prefix, the decibel is a parochial expression of (l) the logarithmic ratio of the loudness of a sound to what is normally audible or (2) the logarithmic ratio of two power signals in radio or electronics. A decibel is not a unit, much less an SI, unit and has nothing whatsoever to do with the acceleration of drill handles. Stating that m/s2 (acceleration) is decibels is without reason. Whoever reviewed this material should not have allowed publication of figures of dB and H.[ ] Exposure to Hand-Transmitted Vibration. This was clearly stated in the "measurement protocol" section of our paper. This quantity is then referred to as the acceleration level and is expressed in dB. We may have inadvertently caused some confusion when we simply used the term acceleration to refer to acceleration level on our diagrams. At the time, we felt the use of dB or m/s2 would make the context clear to the reader. For any confusion this decision may have engendered, we apologize. Since the decibel expresses the ratio of two like quantities, it certainly has no dimensions. It is, however, common practice to treat "decibel" as a unit as, for example, in the sentence, "The acceleration level measured at the operator's hand was 160 dB." The expression of measured quantities in dimensionless form is not inherently unacceptable. In fact, in many areas of engineering it is standard practice (consider the use of Reynolds Number, Nusselt Number, etc.). The fact that the decibel is a dimensionless quantity makes the question of whether it is a SI unit nonsensical. However, it is valid to insist that the dimensional quantities used to obtain the decibel values be expressed in SI units. A careful reading of our paper will make it clear that the measured acceleration was, in fact, expressed in units of m/s2 as was the reference acceleration (l x 10-6 m/S2). These are the accepted derived SI units for acceleration. See, for example, the standard ASTM E380-89a Standard Practice for Use of the International System of Units (SI) (The Modernized Metric System). Concerning Mr. Dasher's implication that hertz (Hz) is an unacceptable unit of measure for frequency, we would again refer him to the standard ASTM E380-89a. Here, he will find (section 2.4.2) that hertz is an accepted "special name" for the derived SI units-1. This is in keeping with numerous other international standards including ISO 5349-1986(E) to which we referred in our paper. In conclusion, we agree with Mr. Dasher on the desirability of expressing measurements in modern SI units. But we would remind him that the standards that define the use of these units, and the accepted means of presenting measured data, are in a continual state of refinement. It is, therefore, incumbent upon him to keep abreast of these changes if he wishes to constructively critique the work of others.[ ]

Jan 1, 1992

By H. Sahay

The current Canadian coal production is approximately 57x106 tonnes per annum of which some 25 million tonnes is exported. Two thirds of the Canadian output is classified as thermal and one third as coking or metallurgical coal. The Canadian coal industry, like the industries in some other industrialized nations, has gone through a cycle of ups and downs. The current world vide recession and stable oil prices have somewhat dampened the plans for a further growth of this industry - albeit temporarily. No new mines are expected to be developed within the next few years. However the production is projected to increase to 60x106 tonnes in 1985 increasing to an estimated 75 to 80x106 tonnes by 1995. The Canadian mines are highly mechanized and are willing to employ the modern technology to maintain its competitive position in the world's coal market. This paper reviews the recent technical developments which continue to improve resource recovery and productivity.

Jan 1, 1986

By Colin Lawrence

The Port of New York and New Jersey is one of the most heavily used transportation arteries in the world, handling nearly 40 per-cent of the North Atlantic shipping trade and directly providing nearly 230,000 jobs to the local economy. In 2004, $100 billion worth of consumer goods moved through the port. To accommodate future cargo volumes in the port, which are expected to double over the next decade and possibly quadruple in 40 years, deeper shipping channels are needed to provide access for a new generation of cargo mega-ships with drafts exceeding 13.7-m (45-ft) when loaded. Current channels within the harbor range in depths up to 13.7-m (45-ft), thus preventing carriers from using these larger ships, or requiring significant reductions in cargo to achieve lesser drafts to operate safely within the harbor. As part of the Harbor Deepening Project, the Anchor-age Channel would be deepened to 15.2 m (50 ft) below mean low water (MLW), for a length of 5,790 m (19,000 ft). The New York City Department of Environmental Protection (NYCDEP) owns, operates and maintains two existing water siphons in the harbor. Due to their shallow depth, both existing siphons must be relocated before dredging of the Anchorage Channel can be completed. Tom Costanzo, manager of capital programs for the Port Authority of New York and New Jersey (PANYNJ), says that ?While the re-location of the existing siphons under the Anchorage Channel is vital to the success of the deepening program, it is also a story of cooperation among key agencies at different levels of government resulting in improvements that will benefit the people of this region greatly.?

Jun 1, 2010

By Brendan Demich, Joseph McGuire, Emily J. Haas

Near misses recorded and reported by workers can provide awarenessto the potential causes of injury and prompt safety management initiatives. Although most companies require near-miss reporting, it is unclear what the value of these reports are, if any, and how they influence subsequent actions or controls to reduce on-the-job risks. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a case study with an aggregates company in which near-miss reports were analyzed at each of their locations over an entire quarter during the summer of 2018. Within that quarter, workers recorded 249 near misses. Of those, 167 were valid near misses that occurred at work. Researchers coded the reports using a qualitative 5 × 5 risk matrix. Of the 167 near misses, 19% were deemed low risk, 25% moderate risk, 30% high risk, and 26% critical risk. Several patterns in the near-miss incidents were documented, including classification of incidents and common corrective actions referenced (i.e., elimination/substitution, engineering control or redesign, work process/procedures, and personal protective equipment). The analysis provides insight into ways that risk communication and management programs can be improved to reengage workers and their situational awareness on the job.

Table A. Conversion of English to SI Units Table B. Strength Properties of Rocks Table C. Engineering Properties of Rock Table D. Properties of Common Minerals Table E. Material Properties and Characteristics Table F. Heat Value of Various Fuels Table G. Geometrical Relationships and Mensuration Formulas Table H. Standard Sizing and Meshes Table I. Ship Measures Table J. International Atomic Weights Table K. Time Value of Money Factorsfor Discrete Compounding

Jan 1, 2008

By Earl M. Frizzell

Investigation of mined land characteristics, evaluation of irrigation systems and evaluations by the mining industry determined that irrigation is a feasible method for aiding the revegetation of coal mined lands in the western arid and semi-arid regions (Sherman, et al. 1980). The various regions studied displayed a commonality of characteristics which enables, independent of the site or region, the recommendation of solid-set irrigation. Irrigation should be supplemental by complimenting natural precipitation and should be implemented on a temporary basis. For germination, the vegetation requires application of small amounts of water in a gentle, frequent, and timely manner. For the establishment phase of growth, moisture should be applied and stored in the soil either through pre-irrigation or deep irrigation.

Jan 1, 1985

By S. K. Kawatra

The use of inferential particle sizing for a closed wet grinding circuit control has been practiced for several years. This paper presents a review of some inferential sizing equations developed for pilot and industrial plants using regression analysis. An analytical development is then presented showing how the general inferential sizing model arises from the nature of the classifier model. The relation between the general sizing model and the individual equations is then discussed.

Jan 1, 1982

In early 1970, General Mills Chemicals, Inc. announced the availability of en improved liquid ion exchange reagent, LIX® 64N, for the recovery of copper from various solutions, such as dump leach liquors. LIX 64N has been shown to be a considerable advance over LIX 64, and is presently in use in three commercial plants. Results have been very gratifying. For example, one of the plants was designed for operational production of 40,000 pounds copper per day, and in fact reached this output within the third week following startup of the plant. In addition to the operating plants, another is scheduled to come on stream this month with L D( 64N being used to extract and recover both copper and nickel. The chemical properties and operating characteristics of this reagent have been fully described in a previous paper. 1 LIX 64N is quite an effective and selective extractint for copper, even with copper contents as high as 15 g/l, but the reagent is somewhat limited in pH range, and loses some of its extraction efficiency as the pH drops below 0.8. Liquors derived from vat leaching, electrolytic tankhouae bleed streams, or some of the new leach schemes derived to solubilize copper from sulfide concentrates are examples of the liquors that present major problems when treated via liquid ion exchange. LIX 64N could extract some of the copper from such streams, but recovery was limited to about 75 percent. Also, in some parts of the world there are streams which are relatively low in copper (-5 g/l) but which are very high in acid (25-50 g/1 H2SO4). Again, LIX 64N can attain only about 75 percent recovery from such streams. For effective treatment, these streams require a reagent which will maintain the excellent selectivity of LIX 64N, and will

Jan 1, 1971

By G. M. Rao, P. N. Deo

Graphite is soft and easily floatable but it is quite difficult to obtain high purity concentrate at coarse sizes. Chemical treatment can produce high grade concentrate but it is an expensive process. Graphite containing plus 96% fixed carbon (FC) with coarse flakes commands high price in international market. Such graphite concentrate containing plus 96% FC was produced in Indian Bureau of Mines (IBM) by using newly developed reagent (mixture of different hydrocarbons and terpenes, IBM/D7) instead of commonly used frothers viz. pine oil, MIBC, kerosine etc. and regrinding in a special type of mill with special grinding media instead of grinding in a conventional ball/ rod mill followed by cleaning. Both the new reagent (frother) and special grinding media are inexpensive and readily available. The process is under patenting. This paper focuses application of this new grinding methodology for flake size protection, and the new reagent for selective flotation of high purity graphite.

Jan 1, 1995

By William I. Weisman

Natural sodium sulfate is obtained from both brines and solid deposits. The brines almost always contain other salts with sodium chloride predominating. They may be obtained from surface occurrences, such as Great Salt Lake or from shallow subterranean deposits. Althought many sodium sulfate minerals are known to exist, only three are of commercial significance. These are thenardite, the anhydrous salt; mirabilite, the decahydrate; and glauberite, the double salt of sodium and calcium sulfate. The reader is referred to Weisman (1983) for details on mineralogy and geology of sodium sulfate minerals. Sodium sulfate deposits, either in the form of brine or solid minerals, are found in many parts of the world. Natural sources, by far, provide the primary supply of commercial grades in Canada, Mexico, Spain, and probably in the U.S.S.R., Chile, Argentina, and Turkey. In the United States, production of natural material and synthetic (including by-product) are about equal in volume and have been for many years.

Jan 1, 1984

By Edwarde R. May

The Flambeau volcanogenic massive sulfide deposit located in northwestern Wisconsin occurs within the southern lobe of the Canadian Precambrian Shield. The steeply dipping tabular body occurs in a complex pile of cyclic schistose intermediate to felsic fragmental volcanics. No chloritic alteration pipe is recognized but adjacent rocks have undergone magnesia metasomatism and subsequently were metamorphosed to the upper greenschist and lower amphibolite facies. Although modest in size the deposit is of special interest in that it has an extensive and well preserved supergene enrichment blanket. Economic minerals found within a pyritized quartz-sericite schist are chalcocite and bornite overlying primary chalcopyrite.

Jan 1, 1976

By Norman R. Paterson

In November 1980 a combined airborne electro-magnetic (INPUT.) and magnetometer survey was conducted by Questor Surveys Limited in the State Line Area, Colorado-Wyoming. The survey was the result of discussions over a prolonged period between the authors and various investigators of the State kimberlite occurrences. As a result of these discussions and literature studies, it was decided that airborne geophysical methods would be potentially useful in the exploration for new kimberlite occurrences. The survey was designed by Paterson, Grant and Watson Limited and conducted by Questor Surveys Limited over an area in which more than 15 kimberlite bodies were known and on some of which ground geophysical surveys had been conducted. The survey was designed primarily to determine the airborne electromagnetic and magnetic responses of the known occurrences and to deter- mine whether these responses would be detectable under similar conditions in other parts of the State Line District and elsewhere.

Jan 1, 1984

By J. O?Hanlon

The 4500 m3 blast furnace at the Redcar Works of ESC operates or, a burden of sinter and pellets, both materials being produced within the works. The early history of the furnace was given to the AIME Ironmaking Conference in 1981(1) when the burden was 65% superfluxed minter and 33% acid pellets. While ironmaking performance was adequate, it was felt that there were advantages to be gained by the use of fluxed pellets. For example, Kobe Steel had reported (2) that the rise of 30-50% dolomite fluxed pellets had enabled them to achieve better furnace permeability, higher gas utilisation, and enhanced ore/coke ratios. It appeared probable to BSC that the use of magnesia-bearing fluxed pellets would give a burden which had compatibility of softening and melting properties, i.e., fluxed sinter and dolomite pellets would result in a thinner cohesive zone because of closer matching of softening and melting temperatures, with consequential benefits on furnace stability and efficiency.

Jan 1, 1983

More than 1,200 professionals from the global tunneling and underground space industries are expected to be on hand for the 2009 Rapid Excavation and Tunneling Conference to be held at Caesars Palace in Las Vegas, NV. The conference, set for June 14-17, is sponsored by the Society for Mining, Metallurgy, & Exploration, Inc. (SME) and the Construction Institute of the American Society of Civil Engineers. The four-day conference will feature more than 100 technical papers in 19 sessions. Two one-day short courses are also planned, as are a pair of field trips. And the show?s exhibit will feature more than 120 of the industry?s leading equipment and service suppliers.

Jan 1, 2009