Search Documents

By C. Wade, A. Swart, M. Dworzanowski

AngloGold Ashanti operate a pyrite flotation plant at their East Gold Plant, Acid Plant and Flotation Plant (EGAF) metallurgical complex within their Vaal River operations in the North West province in South Africa. The flotation plant feed is reclaimed pyrite rich tailings and the concentrate produced is used as the source of sulphur for the EGAF acid plant. The sulphuric acid produced is in turn used for the recovery of uranium at the Vaal River South uranium plant. The original flotation plant built in 1960 was based on the use of many small volume flotation cells and was becoming very expensive to operate and its age severely limited further operation. A decision was taken in 2005 to replace this plant with a new one based on fewer, larger volume flotation cells. This paper describes the benefits of using larger volume flotation cells in this new flotation plant when compared to the smaller volume flotation cells in the old plant. The benefits of the new plant include a smaller plant footprint, fewer flotation cells, fewer pumps, no distribution boxes, simpler piping, a greater flotation volume and a reduction in installed power. The saving in capital cost could not be quantified because of the age of the old plant. The savings in operating cost will arise from fewer operators, less maintenance and reduced power consumption. The new plant has not been in operation long enough to quantify the benefits in operating cost and metallurgical performance. However, recovery improvements can be expected given the greater flotation volume (increased residence time) and the installation of larger, more efficient flotation cells.

Jan 1, 2007

By K. M. Godiwalla, S. Ranganathan

The thermal state in submerged-arc furnaces (S.A.F.) producing ferro alloys is important for the conditions of both the grade of alloy produced as well as specific energy consumption. The temperature profile in the S.A.F. is affected by the endothermic chemical reactions and the rate of gas evolution. The gas evolution commences at about 900 C due to the reduction of iron in the ore. A first-principle-based 2-D model has been developed to predict the temperature profile in the furnace. In this study, four ores of different grades have been considered in order to simulate the thermal profile in the S.A.F. The influence of the composition of the ore on the thermal profile and its significance in rationalisation of charge distribution to optimise the process are discussed.

Jan 1, 2007

By O. I. Ostrovski, D. K. Belashchenko

The aim of this paper is the construction of models of systems with ionic and ionic-covalent bonds (molten salts) using experimental diffraction data and the calculation of their structure and thermodynamic and transport properties. Modelling was performed using algorithm BELION, in which the non-coulomb part of interaction potential between ions in the model was determined by the method of iterative simulation which targeted agreement between calculated and experimental partial pair correlation functions (PPCFs). The ionic charges in salts, which can be fractional, were determined by minimization of internal energy. In this paper, the algorithm BELION is applied for chlorides of alkaline-earth metals. Pair potentials, PPCFs, atomization energies, self-diffusion coefficients and electric conductivity are calculated. The charge of alkaline-earth metals was in the range of 2.0-2.1, slightly increasing from Mg to Ba. Partial pair correlation functions and atomization energies of models agree well with experimental data for MgCl2, SrCl2and BaCl2. Keywords: molten salt, molecular dynamics, partial pair correlation function, ionic charge, atomization energy, diffusion.

Jan 1, 2004

By H. Urata, K. Ishii

To determine the effect of F ions in the molten alkali silicate systems on their structures, quenched Na2O-SiO2-NaF systems were investigated by Raman spectroscopy and molecular dynamics simulation. The systematic increase of 1100 cm-1band intensity in the Raman spectra of the silicate melts accompanying the replacement of F for O provides the evidence for concomitant polymerization of melts. From the molecular dynamics simulation, it was confirmed that most of substituted F was mainly coordinated to Na+ ions but not Si4+ions. These results were consistent with the mechanism in which F associated with otherwise network-modifying Na rather than with network-forming Si. Since F was associated to Na+ ions, the replace of O ion by two F ions promote the polymerization of silicate melts. Keywords: fluorine; molten flux; slag structure; molecular dynamics simulation; Raman spectroscopy.

Jan 1, 2004

This paper pays tribute to the pioneers in geomechanics, and addresses some of the most pressing issues of our time related to deep mining, and how to mitigate these issues. Solutions developed by our predecessors seem to have reached their limits as mines continue to go deeper. The International Society for Rock Mechanics (ISRM) guidelines for rock mass characterization for excavation design also require re-thinking to reflect current knowledge and experience. Thus, a whole new approach is urgently required to increase mine safety and productivity. The paper will draw on the challenges and experiences in medicine and science that have been overcome through genuine collaboration, advances in technology, and impressive funding, which can be adopted to provide solutions to contemporary geomechanics challenges for increased safety and productivity as mines continue to go deeper.

Jan 1, 2014

By T. Proietti, L. Mongiovì, L. Simeoni

Reliable estimates of the kinematic characteristics of movements are obtained by using a statistical model SSM. This model represents a useful tool for the management of alert and alarm systems. L'élaboration des données du déplacement médian d'un modèle statistique SSM opportun fournit des estimations fiables des caractéristiques cinématiques du mouvement. Le modèle peut être ainsi utilisé pour la gestion des systèmes d'alarme. Die Bearbeitung von Bewegungsdaten anhand eines geeigneten statistischen Modell SSM ergibt vertrauliche Abschätzungen der kinematischen Eigenschaften der Bewegung. Das Modell kann also für das Management von Alarmsystemen verwendet werden.

Jan 1, 2003

By J. P. W. Bennie, A. de Jong, G. M. Denton

Mintek together with Middelburg Steel & Alloys, developed the DC arc furnace process for the production of ferroalloys with the expressed objective of smelting ore fines (<1mm) without the need for agglomeration. In the case of ferrochrome production, the DC arc furnace, being a semi-open bath operation, loses radiant energy directly from the bath to the furnace roof and sidewalls above the melt. This energy loss is reflected in a higher electrical energy usage per ton of alloy than for a submerged-arc operation smelting lumpy ores or sintered pellets. The difference increases still further when pre-heated sintered pellet feed is used in a submerged-arc operation. This shortcoming of the DC arc furnace can however be overcome by preheating the feed to the furnace in a fluidized bed or flash reactor fuelled by cold furnace off-gas. In addition to fluidization and preheating testwork, various preheating flowsheets with associated mass and energy balances have been developed and compared from a techno-economic viewpoint. The three major advantages identified were: a) fluidized beds can preheat ores and fluxes up to 950°C without sticking and defluidizing, b) the open bath DC arc furnace does not require expensive coke or char to maintain the burden porosity and, c) the capital cost associated with the milling, pelletising and sintering plant falls away since ore fines are used directly.

Jan 1, 2004

By H. Ogasawara

To study the preparation process of an earthquake, we should get closer to the hypocentre. In co-operation with ISS International, we had an experimental field (~200 m x~200 m) without dykes and faults in a South African deep gold mine. We have monitored more than 20,000 seismic events (M<2) with borehole tri-axial accelerometers. We used a data acquisition system with 15 kHz sampling and 120-dB dynamic range. In a remnant area at a distance of 100?200 m, an earthquake sequence associated with an M~2 event occurred. Significant changes in seismic parameters such as stress drop, b-value, energy index were observed associated with the sequence. We installed Ishii?s borehole strain meters and could monitor as large a strain change as 10-4associated with mining. However, sampling was only 4 times per hour and 12 bit A/D. A distance from the M2 sequence was ~100 m, being not close enough. Therefore, we found another field with several crosscut tunnels excavated across a fault where an M=2-3 event is expected. We installed the strain meter within several metres of the fault to monitor both shear and normal strains on the fault. The strains are continuously digitized with a 24-bit 25-Hz A/D conversion. The Earth Tide (10-8)is clearly detected. Seismicity induced by longwall mining can be compared to earthquake swarm induced by fluid intrusion to vertical dykes. We also found a decrease in energy index in the source area of M>5events a few days before the major events. Keywords: seismic monitoring, strain monitoring, seismic parameters, preparation process of an earthquake, South African gold mine.

Jan 1, 2002

The mining industry worldwide is currently facing a significant restructuring process. In most underground mines, widespread mechanization of the mining processes increases production while reducing staff numbers. At the same time, mining depths as well as the lateral spread of the mine workings are increasing. This ever-changing mining environment requires sophisticated solutions for the design and operation of underground mines. In fact, a reduced number of mining engineers is taking responsibility for everincreasing mine operations. This applies not only to the excavation of the minerals, but also to all other aspects of the mining operation, including health and safety, disaster management, and mine rescue organization. Most mining engineering graduates entering the industry lack experience in mine emergency management. Young engineer trainees must learn mine emergency management and rescue work in addition to their normal training experience on the job. Often, and unfortunately, emergency and rescue training at different mining companies is not carried out to the highest level and standard and with the best possible training outcomes. The tasks and challenges a young engineer faces while being trained in a new position do not leave much room for additional training in mine rescue and emergency management. At the same time, experienced, ?old hands? are retiring and cannot easily be replaced due to limited graduation numbers. Strategies are being developed at mining universities worldwide to train mining engineering students in handling mine emergency situations and to provide hands-on experience for managing potential accident and disaster scenarios underground. Two of these strategies, from the USA and from Central Europe, are presented in this paper. These specific strategies have to be seen under special consideration of the local and regional boundary conditions, but might serve as case studies for mining schools and universities in other countries.

Jan 1, 2014

By N. Henderson, J. Weyer, J. F. Brune

"The mining industry worldwide is currently facing a significant restructuring process. In most underground mines, widespread mechanization of the mining processes increases production while reducing staff numbers. At the same time, mining depths as well as the lateral spread of the mine workings are increasing. This ever-changing mining environment requires sophisticated solutions for the design and operation of underground mines. In fact, a reduced number of mining engineers is taking responsibility for everincreasing mine operations. This applies not only to the excavation of the minerals, but also to all other aspects of the mining operation, including health and safety, disaster management, and mine rescue organization.Most mining engineering graduates entering the industry lack experience in mine emergency management. Young engineer trainees must learn mine emergency management and rescue work in addition to their normal training experience on the job. Often, and unfortunately, emergency and rescue training at different mining companies is not carried out to the highest level and standard and with the best possible training outcomes. The tasks and challenges a young engineer faces while being trained in a new position do not leave much room for additional training in mine rescue and emergency management. At the same time, experienced, ’old hands’ are retiring and cannot easily be replaced due to limited graduation numbers.Strategies are being developed at mining universities worldwide to train mining engineering students in handling mine emergency situations and to provide hands-on experience for managing potential accident and disaster scenarios underground. Two of these strategies, from the USA and from Central Europe, are presented in this paper. These specific strategies have to be seen under special consideration of the local and regional boundary conditions, but might serve as case studies for mining schools and universities in other countries."

Jan 1, 2014

By F. W. Petersen

The Conference Minerals & Materials &apos;96 was held in Somerset West, South Africa, from 31st July to 2nd August, 1996. It was organized by the Universities of Stellenbosch and Cape Town, the Cape Technikon, and the Western Cape Branch of The South African institute of Mining and Metallurgy (SAIMM). The three-day Conference was attended by 180 delegates, representing countries such as Australia, South Africa, United Kingdom, Finland, Sweden, Germany, Poland, Zambia, and Zimbabwe. The programme and associated exhibition were well organized, and each of the delegates received two volumes of proceedings containing the 77 papers presented at the Conference.

Jan 1, 1996

By E. Kapilashrami, S. Seetharaman

Refractory/metal interactions and associated reactions are significant during casting as they can lead to inclusion formation. High-temperature interactions between aluminosilicate refractories and molten steel were studied in the present investigation using the sessile drop method. The changes in the contact angles between molten iron with well-defined oxygen levels and substrates of silica, mullite (3Al2O3?2SiO2) as well as commercial refractories were measured in the dynamic mode. In all cases, the reaction led to slag formation. The experiments were performed under isothermal conditions at 1823 and 1873 K. A known and constant oxygen partial pressure was imposed above the iron drop, through appropriate CO-CO2-Ar mixtures. For all substrates, the contact angles started decreasing due to the lowering of the surface tension of iron, as oxygen was imposed on to the system. When a critical level of oxygen was reached, slag started forming at the drop/substrate interface and at this stage, the contact angle dropped suddenly. Subsequent behaviour of silica and mullite was observed to be different, with SiO2showing a non-wetting behaviour. In the case of SiO2substrate, there were also deep erosions along the periphery of the drops and there was slag accumulation at the sides of the metal drop, probably due to Marangoni flow and/or SiO(g) formation. SEM and EDS analysis of the substrates revealed that the formed slag was fayalite. The thermodynamic criteria for slag formation and possible mechanisms of the reaction are discussed in the light of the experiments. Key words: silica, mullite, fayalite, corundum, slag formation, sessile drop.

Jan 1, 2004

By J. N. Van der Merwe

The results of over 900 coal strength tests done during the period 1993?1994 for the SIMRAC project COL021A were re-analysed with a view to find a method to delineate areas or seams that can be grouped together for analyses of coal strength and strength decay characteristics. It was confirmed that the strength of a coal specimen increases linearly with increasing diameter-to-length ratio and decreases exponentially with increasing size of specimen. However, by extrapolation of the data, it was shown that beyond a diameter of approximately 2 m, the size effect is insignificant. For larger specimens, the diameter-to-length ratio (referred to as the width-to-height ratio for full scale mine pillars) alone continues to influence the strength. The slope of the linear strength vs. diameter-to-length ratio relationship is independent of the size of the specimen and is not unique for coals from different mines. However, the intercept of that relationship is unique and is a function of specimen size. This offers a previously unknown method to distinguish between the coals from different mining areas and coal seams. Ranked from weakest to strongest, the samples tested from the different mines are in the order shown below, which roughly corresponds to the judgement of practising rock engineers in the field: ?Sigma ?ZAC ?Goedehoop ?Kriel ?Bank ?Blinkpan ?Secunda ?Greenside Arnot ?Khutala ?Delmas

Jan 1, 2003

By S. Ganguly, R. Kononov

Carbothermal reduction of manganese oxides and manganese ores in the solid state was studied in hydrogen, helium and argon at different temperatures, ore compositions and carbon to manganese oxide ratios. Wesselsore (South Africa) and two grades of the Groote Eylandt ore (Australia) with different level of impurities were examined. Ores were characterised by XRD, X-ray fluorescence, optical microscopy and scanning electronmicroscopy. Isothermal and temperature programmed carbothermal reduction experiments were conducted in a fixed bed reactor in a vertical tube furnace, with on-line monitoring of gas composition by the CO-CO2 infrared sensor. The reduced samples were characterised by XRD, SEM and LECO analyses. Extent of reduction was calculated using data on the off-gas composition, and LECO carbon and oxygen contents in the reduced sample. Manganese oxides in the ore were reduced to a-Mn and carbides Mn23C6 and Mn7C3 depending on the carbon to ore ratio. The reduction rate of manganese ores in hydrogen was higher than in helium and argon. Key words: Manganese, Carbothermal Reduction, Hydrogen, Argon, Carbon Monoxide, Helium, Kinetics.

Jan 1, 2007

By J. M. Lottering

Paper written on project work carried out in partial fulfilment of B Eng (Chem) degree Operational factors influencing the electrostatic separation of mineral sands were investigated in a laboratory separator. Measurements were collected online by means of an optical sensor using diffused reflectance spectroscopy to determine the mineralogical composition. The results have shown that the roll speed and potential were the dominant operating variables, collectively explaining more than 83% and 68% of the product grade and yield, respectively. In contrast, the feed rate, temperature and position of the plate did not affect separation. The effect of the ambient relative humidity, ranging from 10% to 45%, could not be assessed conclusively and at best appeared to have a weakly beneficial effect on the product grade. Keywords: process modelling, high tension roll separator, mineral sands

Jan 1, 2006

By B. Larsen, S. Z. Nascimento, K. Fidje, J. P. M. Amaro, H. Gran

Safe and good operation of Søderberg electrodes is dependent upon high quality electrode paste coupled with correct electrode operating procedures. Good electrode performance depends further on proper melting and densification of the electrode paste. The melted paste should form a dense and viscous layer that prevents gasses from the baking process to move upwards. Both paste cylinders/blocks and briquettes can be used, but the procedures may differ between the various types of paste products. For briquette columns the formation of the important viscous layer is obtained through melting and densification of the briquettes. By basic rheological studies of electrode paste and by laboratory tests of briquette beds at isothermal conditions we have achieved a better understanding of the melting process. The effects of temperature gradients, pressure and friction between the briquettes and the electrode casing have also been evaluated qualitatively in pilot scale experiment and in industrial scale tests. The paper shows that melting and densification starts at a considerable lower temperature than the pitch softening temperature. It is concluded that the formation of a briquette electrode column depends on parameters as temperature, briquette column pressure and the friction. Operating conditions influencing the above parameters should be defined and established for each specific furnace operation. Such factors are e.g., charging and slipping procedures, column heating and electrical conditions.

Jan 1, 2004

By Masanobu Masukawa, Toshio Shiota

The shaft-type ferromanganese smelting furnace (SF) at Mizushima Ferroalloy Co., Ltd. has been in operation since startup in 1985 and is continuing to perform smoothly. Production has been increased from the original design capacity of 270t/d to 350t/d by various operational improvements. As a productivity index of the shaft-type furnace, production of 350t/d is equivalent to productivity of 0.9t/m3/d (daily production/cubic capacity of furnace). Recently, various operational improvements were implemented to achieve productivity of 1.0t/m3/d or higher, including oxygen enrichment operation, increased tapping frequency, maintenance of the throat profile, and operation with small lump coke. The target productivity of 1.0 t/m3/d was achieved in January 2005. This report describes the improvements introduced as part of this high productivity technology.

Jan 1, 2007

By J. H. Van Reenen, H. Thiele, C. Bergman

For some time spirals have been the process equipment chosen to recover metal in the size range 0.15 to 3mm from ferrochrome and silico/ferro manganese slags. Recoveries of metal obtained using spirals are usually about 70%. Spirals are also difficult to control. By combining a novel gate on the Apic pneumatic fines jig with the recently developed Apic classifier, metal recoveries of 76% and grades of over 90% have been obtained for FeCr and SiMn slags in the size range 0.15 to 3 mm. The paper compares classifier operating performance and costs with those spirals for FeCr and SiMn metal recovery from slags. The classifier technology can also be applied to chromite and iron ores and coal fines.

Jan 1, 2004

By C. Chongo, F. X. Paquot, C. Ngulube

"Over the last six years, the Kansanshi copper/gold mine has continued to process significant quantities of complex transitional mixed ores. The effect of the complex mineralogy on the flotation performance is depicted. Initially, ore treated came predominantly from accumulated stockpiles. In the ensuing years, ore treated shifted to primarily freshly mined ore that generally showed less tarnish with better float kinetics but with the downside of producing lower concentrate grades. A number of changes were made to improve the efficiency of the roughing circuit and quality of concentrate produced. These changes were as a result of initial mineralogical studies and laboratory float test work done and discussed at length in a previous paper. Salient among the adopted recommendations from previous work were increasing circuit capacity and modifying configuration to increase the residence time and the number of sulphidisation stages. These modifications were completed and commissioned in 2011. This, however, resulted in significantly low rougher concentrate grades and subsequently below-specification final concentrate product. This was primarily due to higher mass pulls resulting from the extended rougher bank with multiple concentrate discharge streams. This necessitated the need for an enlarged cleaning capability to offset this. The extra cleaning capacity came on-stream in 2014. Of note was the development of a recovery model, based on the strong correlation between the total copper and acid-soluble copper ratio, as a tool for monitoring plant performance. INTRODUCTION The Kansanshi mine, the largest copper mine in Africa, is 80% owned by Kansanshi Mining PLC, a First Quantum subsidiary. The remaining 20% is owned by the state through the parastatal ZCCM. The mine is located approximately 10 km north of the town of Solwezi and 180 km to the northwest of the Copperbelt town of Chingola. The mine has been in commercial operation since 2005. Prior to June 2009, Kansanshi mine treated only two ore types: oxide and sulphide. All transitional ores mined during the period leading up to 2009 were stockpiled. The treatment of the minerologically complex, transitional ores through a third train commenced in June 2009 but with numerous metallurgical challenges. This transitional ore (called mixed ores) could not be previously treated economically due to high gangue acid consumption (GAC) minerals association (making it unsuitable for the oxide float–leach circuit) and poor flotation response ruling out the conventional sulphide float circuit. The new novel circuit involved a conventional sulphide pre-float followed by flotation involving staged controlled potential sulphidisation (CPS)."

Jan 1, 2015

By J. J. Bezuidenhout

The waste-heat boiler is used within the Sulphide flash smelting process as the main dust and energy recovery unit. The large volume of off-gas discharged from the flash smelter is at a very high temperature (1350°C) and contains a significant dust load that subjects the downstream waste-heat boiler to tough and demanding conditions. The boiler cavity is especially prone to dust accretions, fouling, and corrosion caused by accumulation of molten particles and precipitation of sulphuric acid. Computational fluid dynamics (CFD) is applied within a qualitative study to model the flow and heat transfer distribution throughout the waste-heat boiler. The commercial CFD package, Fluent 6.2.16, was applied to a modified waste-heat boiler (23 m ×11 m ×5.4 m) within the Outokumpu flash smelting process. This investigation focuses on the geometric modifications to the typical boiler design, which includes elevation of the ceiling, placement of flow-obstructing baffles and radiation plates parallel within the flow path. Also investigated were various boiler operating conditions such as the circulation of process off-gas, air leakage from the dust discharging hoppers and variation in inlet gas composition. The geometric modifications had the desired effect of increasing the volumetric utilization and therefore enhancing heat transfer between the boiler surface and the gas stream and dust segregation. Introducing circulated off-gas at a rate of 20 m/s and at a 45° angle to the front of the waste boiler further enhanced cooling while reducing the high impact of the furnace-uptake gas-stream on the boiler ceiling. The placement of radiation plates was found to be very effective in enhancing the heat transfer surface and distributing gas flow within the boiler. These results present recommendations towards an improved waste-heat boiler design. Keywords: flash smelting, waste-heat boiler, CFD simulation, off-gas cooling.

Jan 1, 2008