Search Documents

By J. J. Van Rensburg

The commissioning of a test facility for the calibration of anemometers by J. J. VAN RENSBURG (Student Member). After the erection of a commercially produced open-jet wind tunnel for the calibration of the anemometers used in mine ventilation, the wind tunnel was calibrated for routine use. There is a choice of five orifice plates. which, together with a variable-speed fan, can give a measurable range of air velocities in the test section from about 0,05 to 35 m/so The orifice plates were calibrated against a standard pitot tube, and it is now necessary only to measure the pressure drop across an orifice plate and to read off, from a set of graphs, the true outlet velocity in the test section. The paper describes the underlying theory and the test results.

Jan 4, 1975

By Y. Fan, D. H. Zhang, J. Y. Xu

The hydrogeological conditions in the Chambishi mine area in Zambia. were investigated. Chambishi is a very wet mine and groundwater discharge costs are high. The research goal was to identify methods to reduce the discharge costs without greatly affecting the mining process. Hydrogeological data was obtained from measurements in drill-holes and from drill cores. The differences in structural deformation in different areas determine whether a layer of rock is an aquifer. In the mine region, the Lower Roan Group ore shale and quartz-sandstone unconformably lie on the basal schist and granite aquifuge. The Upper Roan Group dolomite is continuously distributed over a large area around the orebody. This dolomite is the main target of groundwater control efforts, and its water yield is also influenced by the deformation intensity. Based on the observations, backfilling was gradually adopted to appropriately safeguard the integrity of the aquifuge above the orebody. The overlapping relationship between the aquifer and aquifuge has been utilized to increase mine drainage efficiency. This measure has not only greatly reduced the costs of mine drainage, but also improced protection of the groundwater environment. The old drill-holes that were not sealed after exploration drilling were grouted. Further, possible water-conducting fracture zones were investigated. Cover drilling towards the suspected zone was conducted to prevent the high-pressure groundwater from shallower aquifers from entering stopes in deep areas of the mine.

Jun 10, 2024

By S. Burks

This paper develops the themes explained at the previous SAIMM Platinum conference by Whittle and Burks1. Optimization techniques can be used to significantly increase the value of mining businesses by enabling better long- term planning decisions. Open pit and underground mine design, mine scheduling, cut-off grade and blending, stockpiling, and the linking of these to flexible elements of the metallurgical recovery processes are all evaluated together. Transport or sale of intermediate products and the requirements of the product metal markets can also be considered. Experience shows that net present value (NPV) can potentially be increased by 5-35 per cent or more, usually even before the expenditure of significant amounts of project capital. The case studies presented include: ? An existing operation with multiple open pits and PGM concentrators linked to offsite downstream processing facilities, and with infrastructure constraints for which the scheduling of current operations and the potential for expansion were investigated ? An existing operation with an integrated portfolio of mines, concentrators, smelter and refinery, for which the various possible sources of ore for processing were prioritized to match the downstream process plant constraints and the product markets ? An underground operation in Zimbabwe for which the optimum mining width was calculated and expansion plans were evaluated ? An underground mine with many separate mining sections, for which a revised schedule was developed aiming to keep the shaft system and processing plant at capacity with the highest net value material available at any time throughout the life of mine. In the concluding section of the paper, a few brief notes are included suggesting how the strategic recommendations from enterprise optimization studies may be implemented by the Owner?s team.

Jan 1, 2012

By D. G. Krige

Using a very large number of chip-sample values from a mined-out area of the Hartebeestfontein mine and accepting these as equivalent to borehole values (also areas of 1 km by 1 km as equivalent to 'mines'), the authors apply a series of borehole-valuation procedures to these 'mines', Large undeveloped sections of existing mines are also regarded as the equivalent of such 'mines'. These procedures start with the orthodox arithmetic mean and then introduce additional information in the form of the Iog normal frequency distribution model for Sichel's 't' estimator. Knowledge of the average log-variance within mines leads to the tH estimator. The mean grade of the 'family' of mines to which a new mine belongs is then introduced via regression or elementary kriging. Next, further information on the macro spatial structure of the grade is used, together with the grades of adjacent existing mines in ordinary and simple macro-kriging procedures; finally, via the distribution model, the grade is seen as a function of the logs of the grades and their variances. These are introduced as spatial variables, and both are estimated by macro-Iog normal ordinary and simple kriging procedures with grades and variances from adjacent mines'. Comparisons are also made between macro-kriging on lognormal transformed values versus untransformed values. Conclusions are drawn on the relative importance of the various items of additional information used, on the procedures followed, and on the significance of the advantages gained

Jan 1, 1992

By G. R. Marchant, B. K. Loveday

A mathematical model has been developed for flotation circuit simulation. This model was designed to investigate the effect of varying the circulating loads and to determine whether an improvement in overall efficiency could be gained by a size separation prior to flotation. Model parameters were obtained by regression to plant data. Highly correlated parameters in the model were combined to reduce the number of parameters so that the need for excessive data gathering was eliminated. Mass balance smoothing was used to obtain a consistent data set for regression. The results of the simulation indicate that for the same grade of concentrate, an increase in copper recovery of 0.6 per cent may be possible by increasing the circulating loads. The results of the simulation also indicated that recleaning of the plus 200-mesh material may be beneficial.

The following comment has been received from Mr A. D. Osche* on the above paper, which was published in the Journal in October 1977 (vol. 78, no. 3, pp. 51-62). Obituary: T. K. Prentice The Institute records with deep regret the death on 30th January of its senior surviving Past President, Mr Thomas Kennedy Prentice, at the age of 83. Book reviews R. A. Rich, H. D. Holland, and U. Petersen. Hydrothermal uranium deposits. (Developments in Economic Geology, vol. 6). Amsterdam, Elsevier Scientific Publishing Co., 264 pp. with 77 illustrations and diagrams, 30 tables. U.S. $34,75. M. David. Geostatistical ore reserve estimation. Amsterdam, Elsevier Publishing Company, 1977. 364 pp. World mineral industry The Australasian Institute of Mining and Metallurgy is celebrating its sesquicentenary in 1979. A conference will be held in Perth from 13th to 18th August, 1979, as part of the celebrations, the theme being 'Australia's Role in the World Mineral Industry'. Engineering teaching staff UNESCO has extended its technical assistance to the Venezuelan government in the training of engineers to suit the rapidly developing economy of the country. UNESCO vacancy Vacancy for a post of expert under the UNDP. (1) Title of post: Expert in metallurgical engineering. (2) Duty station: Instituto Universitario Politecnico of Ciudad Guyana (Venezuela). Shell Design Awards The annual Shell Design Awards, organized by the Design Institute and sponsored by Shell South Africa (Pty) Ltd, focus attention on achievements in South African design.

Jan 1, 1978

The nature of metallurgical engineering?applying and optimising chemical and physical processing of ores into useful materials?is reviewed. Important trends that shape the context in which metallurgical engineers practise are identified ? increased global production of primary metals, declining prices, environmental constraints, and increased property requirements of materials. A successful department of metallurgical engineering is one which employs a team of academic leaders to develop graduate engineers who are productive across the full range of metallurgical processing. Keywords: metallurgical engineering, primary metals, commodity prices, processing

Jan 1, 2003

By E. Keskinkilic

"Electrical steels are used in motors, power generators, and transformers for electrical applications owing to their superior magnetic properties. These properties are attributed to the presence of a significant amount of silicon in the steel composition. Silicon steels are mainly grouped into two categories: grain-oriented (GO) and non-grain-oriented (NGO). The Si content of silicon steels is generally between about 0.50% and 6.5%. Therefore, silicon steels are further classified as low-, medium-, and high- Si steels. In this paper, liquid steel processing practices for certain silicon steel grades are outlined by considering a steelmaking company that integrates a basic oxygen furnace (BOF), a ladle furnace (LF), and an RHtype degassing unit (RH). Possible problems are identified, suggestions are discussed, and conclusions are drawn on the basis of real plant data. IntroductionSilicon steels are widely used in motors, power generators, and transformers for electrical applications owing to their superior magnetic properties. They are mainly grouped into grain-oriented (GO) and non-grain-oriented (NGO) silicon steel grades. However, the differences in the properties and thermomechanical production of GO and NGO grades are outside the scope of this paper. In this study, liquid steel processing of certain silicon steels will be discussed. In the integrated iron and steelmaking process, converters are the primary steelmaking units that are used mainly for decarburization and removal of phosphorus, and for obtaining liquid steel with a specific chemical composition and suitable temperature for secondary steelmaking operations. Ladle furnaces are a type of ladle metallurgy station consisting of electrical and/or chemical heating facilities for adjusting the liquid steel temperature during alloying. Various types of vacuum units are used for decarburization and removal of nitrogen, hydrogen, and sulphur, depending on the metallurgical conditions of the vacuum units. In this study, an actual steel-production company is considered in which the primary steelmaking operation uses a basic oxygen furnace (BOF) converter with N2/Ar bottom blowing, and the secondary steelmaking operations involve (1) a ladle furnace (LF) heated by three graphite electrodes and equipped with Ar and N2 top/bottom mixing facilities, and (2) an RHtype (circulation) vacuum degassing unit equipped with a top-blowing attachment for oxygen blowing and an Ar-purging system from an up-leg snorkel."

Jan 1, 2018

By R. Weber

Methane explosions in underground coal mines are a major concern across the mining industry. After the Pike River disaster, Arnot Coal became even more aware of the explosion risk. To determine whether Arnot has adequate precautions against a methane explosion, such as the one that led to the Pike River disaster, a literature survey covering the causes of the incident and what preventative measures should have been in place was conducted. Many different methane explosion prevention methods were evaluated, as well as codes of practice. Based on the findings, Arnot?s measures to prevent conditions favourable for a methane explosion were evaluated.

Jan 1, 2014

By I. Serepa, N. C. Steenkamp

Investigations were conducted to determine the condition and stability of the existing decline at amine in the Kalahari Manganese Field, Northern Cape Province, South Africa. During the inspection of the decline, voids were identified behind the concrete lining on the hangingwall and sidewalls over a total linear distance of 230 m. The voids did not provide confinement and, as a result, self-mining was occurring behind the lining. Water was flowing into the decline, over a total linear distance of 100 m, at areas where the decline intersected incompetent rock units, causing softening of the concrete lining and deterioration of the surrounding rock mass. Further damage to the concrete lining was caused by expansion and contraction of the wet red clay unit. Remedial work comprised void filling and water sealing to prevent further deterioration of the decline and ensure that it remained operable for the remainder of the life of mine. Void filling was accomplished by drilling rows of holes along the decline to access the voids and filling the voids with foam. This was followed by the sealing with polymer fluids. Telescopic pipes were also installed to allow water to drain off. A visual inspection was conducted and check-holes were drilled to assess the quality of the remedial work. The void filling material had penetrated cracks in the concrete lining, and areas where voids were intersected by check-holes were re-filled. Additional holes were drilled to re-seal areas that were still wet. The remedial work was completed successfully, as all voids were filled and stability achieved without compromising the concrete lining. The ingress of groundwater was also reduced to some residual dampness.

Mar 2, 2022

By J. Rajala

The Kupol mill facility processed a high grade free milling gold/silver ore containing 28.2 g/t Au, 324.8 g/t Ag and approximately 0.5% pyrite during 2008 operation. Gold predominantly occurs a selectrum in the ore and silver is predominantly present in the forms of acanthite, stephanite, pyrargyrite and proustite. Mill start-up was in mid-May 2008 and the mill reached the design throughput of 3 000 tpd in October. The ore was ground to approximately 70%?53 microns. A Knelson Concentrator recovered 9.8% gold and 0.5% silver. The gravity tails reported to a cyanidation circuit that has 14 hours pretreatment and 116 hours leaching. The slurry from cyanidation was then processed by counter current decantation (CCD) thickening to wash and separate the leach residue from the pregnant leach solution. Precious metals are recovered fromthe pregnant solution using the Merrill-Crowe process. The washed CCD leach residue slurry is treated with calcium hypochlorite to destroy cyanide and then sent to the tailings impoundment. Leaching is performed with a new technology called ?CELP? (CANMET Enhanced Leach Process). The Kupol mill overall gold and silver recoveries for 2008 were 95.4% and 85.6% respectively, which were 2.8% and 7.5% higher than targets. Gold and silver extractions in the leach circuit were 94.2% and 84.5% respectively. Leach profiles indicated that gold extraction reached a plateau in the 4th tank while minor silver dissolution occurred in the 5th tank. With the CCD circuit included, total gold and silver extractions increased to 95.4% and 86.6%, respectively. Optimization of the leaching strategy made it possible to reduce sodium cyanide concentration to as low as 410 ppm without compromising precious metals extractions. Silver was effectively leached from the refractory silver minerals because CELP produced more oxidized mineral surface relative to the conventional cyanidation leached mineral surfaces. The average cyanide consumption for 2008 was 1.3 kg/t. The new leaching technology proved to be very robust and performed efficiently even with changes in feed grade and ore mineralogy. Laboratory experiments produced results that were indicative of plant performance. The robustness of the technology and the laboratory test work contributed to the success of the Kupol mill start-up.

Jan 1, 2009

By J J. Pretorius, G M. Hoffmann

Utilisation of lower-grade (<60 per cent Fe) resources, not utilised in the current products, is crucial to ensure optimal resource utilisation and maintaining/improving future profit margins by reclassifying low-grade material to ore. The purpose of the Sishen Expansion Project (?SEP?) is therefore to investigate the technical and financial viability of producing up to an additional 10 Mtpa of new products at Sishen from material currently classified as low-grade materials. Jigging technology has progressed to a point where Sishen?s 50 to 60 per cent Fe run of mine (?ROM?) material, once considered as waste, can be beneficiated to produce a saleable 64 per cent Fe product. This has been confirmed through appropriate beneficiation testwork. Consequently, Sishen can now produce saleable product from material not currently included in the resource definition, increasing the resource base of the mine significantly and ensuring higher resource utilisation. Mine Planning utilised the geological models to produce detail planning schedules, reflecting the current and SEP plants separately, optimised to comply with product specifications of both the current and SEP plants and to confirm the viability of the low-grade resources identified as SEP feed material. The SEP products specifications have been derived by optimally matching iron ore market requirements with the revised resource base. A 64.0 per cent Fe lump product and a 63.5 per cent Fe fine product are the optimal SEP products. The SEP plant will be able to produce 10Mtpa at an average yield of 60 per cent and a lump to fine ratio of 62 to 38. The plant consists of five major sections namely crushing, material preparation, beneficiation, final product handling and quality control services. Maximum integration with the current Sishen plant was considered. Kumba currently has an agreement with Transnet to rail up to 23.5 Mtpa through the Sishen Saldanha Iron Ore Export Channel (?IOEC?). Transnet and Sishen Iron Ore Company have signed a Definitive Agreement that deals with the expansion of IOEC?s capacity, which increases Kumba?s entitlement from 23.5Mtpa to 35.0Mtpa. The detailed enviro-legal impact assessments for the SEP indicated that the project has low enviro-legal risk as a result of it being a brownfields project incorporated into the current Sishen operations.

Jan 1, 2006

By M. Gericke

Over the past few decades the commercial application of heap bioleaching technology for the extraction of base metals has become increasingly important, due mainly to the depletion of high-grade ore reserves. Heap bioleaching is widely used for the extraction of copper from secondary copper sulphide ores. The design and engineering aspects of the process have received considerable attention, but issues related to the microbiology of the process have been subjected to less rigorous scrutiny. The major role of micro-organisms in bioleaching processes is to catalyse the regeneration of ferric iron and protons, from ferrous iron and by sulphur oxidation respectively. It is accepted that even the most carefully engineered heaps are heterogeneous in terms of temperature, pH, the presence of anaerobic pockets, irrigation efficiency, and dissolved solutes. Since interactions between solution chemistry, mineralogy, and microbial populations exist in heaps, a better understanding of the correlation between microbial numbers and types with changes in these chemical and physical profiles with time would be beneficial during process design and operation of heaps, and could result in faster start-up times and higher metal recoveries. This paper reviews the role of microbiology in heap bioleaching processes. Aspects such as microbial diversity, identification and monitoring of cultures, inoculation strategies, colonization behaviour, and tolerance to metals and salts are discussed, and the potential contribution of the knowledge to the improvement of the operation and design of heap bioleach processes assessed. Conclusions are drawn with respect to the role of genetic engineering, heap inoculation practises, and remaining areas for future heap bioleaching research and development.

Jan 1, 2012

By T. Ono, B. Altansukh, S. Kawamura, K. Haga, A. Shibayama, Y. Takasaki

In recent years, the grade of silica in zinc concentrate has increased due to the degradation of zinc content and the increase in impurity content in natural ores. It implies that the development of silica removal technology from zinc concentrate is necessary to solve problems in the smelting process caused by the high content of silica in zinc concentrate. In this paper, the authors investigated the silica removal processes from silica-rich zinc concentrate by mineral processing approaches such as re-grinding and flotation. This study focused on the pulverisation process as a pretreatment for the investigation of individual minerals' liberation from the silica-rich zinc concentrates using different kinds of pulverisers. Flotation experiments were performed to separate silica and zinc concentrate from the pulverizsd feed sample using a pH regulator (NaOH), activator (CuSO4), collecting agent (PAX), and foaming agent (DOW froth 250). Results showed that the liberation rate of silica (SiO2) was reached 75% from 13% by pulverisation in an attritor with a 2 mm ball in diameter, while silica accumulated in a fraction over 20 mm in size. Flotation experiments indicated that silica removal efficiency was achieved by 44% from + 20 mm fraction obtained from pulverisation whereas the grade of silica in froth reached 1.85 mass% from 4.5 mass%. Results indicate that silica could selectively separate from silica-rich zinc concentrate, and 99.8 % zinc recovery is achieved under the studied conditions. Keywords: Zinc concentrate, silica, pulverisation, liberation, sieving, flotation

Jan 1, 2020

By F. Nakhaei, Z. Pourkarimi

Tailings produced from the iron ore industry present many challenges due to the high economic and environmental impacts involved with their disposal. However, the relative scarcity of high-grade iron ores has driven manufacturers to recover and recycle these valuable tailings (secondary sources). This study aimed at the purification of ultrafine tailings with high sulphur content from an iron ore concentrator via reverse flotation to produce pellet feed fines. A specially designed flotation column featured with a nano bubble generator and a conventional bubble generator were employed to assess the effects of nano bubbles on the desulfurisation performance of iron ore concentrate under different operating conditions. Results obtained from this study indicated that the sulphur content of iron concentrate could be reduced from 1.2% to 0.22% in the presence of nano bubbles. Also, the results showed that use of nano-micro bubbles increased sulphur recovery 20% more, in comparison to micro bubbles. Keywords: Column flotation, iron ore, tailings, slime, nano bubbles, desulphurisation

Jan 1, 2020

By J. Svoboda, W. J. C. Venter, R. N. Guest

SYNOPSIS Wet high-intensity magnetic separation was examined as a method for the recovery of copper and lead from Tsumeb flotation tailings. Bench-scale and pilot-plant tests were conducted and, despite the very low magnetic susceptibilities of all the complex copper and lead minerals, copper and lead recoveries of over 60 per cent and almost 50 per cent respectively were obtained at a combined copper and lead grade of up to 13,5 per cent. The recoveries were found to be practically independent of magnetic induction in the range 0,5 to 2,2 T, and the grade of the magnetic concentrate decreased with increasing magnetic induction. The grade of the magnetic concen¬trate improved when the flowrate of the slurry was increased, and desliming was found to have a profound effect on the. metallurgical process. Particles smaller than 10 µm were not recovered, and their presence in inefficiently deslimed samples impaired the overall performance of the magnetic separation

Jan 1, 1988

By C. L. M. Gough, L. A. Vermeulen, D. D. Howat

Formulae expressing the dependence of the mass of a grinding ball on the amount of material milled by a ball mill are derived. It is shown that, with the aid of these formulae, it is relativel rsimple for the results of a marked-ball test to be analysed and for the relative performance and cost-effectiveness 0 the various types of ball under test to be evaluated. Predictions based on theory and the results obtained in a marked-ball test in a ball mill are compared detail and shown to be in close agreement. The difficulties associated with marked-ball tests are considered, and an explanation for the decrease in the calculated consumption of the balls, which follows naturally from the theory, is presented. The marked-ball anomaly explained, and it is demonstrated that the ball consumption in a ball mill can be predicted with fair accuracy from the results of a marked-ball test.

Jan 1, 1983

By A. O. Filmer

An account is given of a study on the non-oxidative dissolution in aqueous acidic solutions of nickel sulphides of different stoichiometric composition, in which a rotating ring-disc electrode was used. The rate of dissolution was found to depend on the potential of the sulphide and the nickel-to-sulphur stoichiometric ratio. A maximum rate for the dissolution of nickel from nickel sulphides containing an excess of nickel was recorded at potentials around -0,2 to -O,3V. The rate decreased markedly at more anodic potentials. For nickel-deficient nickel sulphides, the nonoxidative dissolution rate increased with a cathodic shift in potential. Under open-circuit conditions, a nickel sulphide of a composition approximating Ni ,S. reacted most rapidly. The dissolution rate was controlled by either a chemical or an electrochemical reaction at the electrode surface, had an activation energy of between 50 and 65 kJ.mol-1, and was independent of stirring speed.

Jan 1, 1980

By C. R. S. Needes, M. J. Nicol, G. T. W. Ormrod, N. P. Finkelstein

The industrial application of a dioxide electrode uranium by C. R. S. NEEDES, Ph.D. (London) (Visitor), M. J. NICOL, Ph.D. (Rand) (Visitor), N. P. FINKELSTEIN M.Sc. (Rhodes), Ph.D. (Liverpool) (Fellow), and G. T. W. ORMROD (Visitor) A correlation between the potential of a U02 electrode and the rate of recovery of uranium has been proved in laboratory and plant trials. When the recovery rates change because of variation in the concentrations of Fe(III), Fe(II), SO4 &apos;and H+, a positive correlation is observed. However, an 2- increase in the concentration of phosphate in solution produces an increase in the U02 electrode potential but a decrease in the rate of leaching of U02. The correlation between the U02 electrode potential and the rate of leaching of U02 is then negative. It is concluded that, as a control device, the electrode cannot compete with the platinum electrode for use on certain plants. Nevertheless, the U02 electrode will act as a useful warning device if the total concentration of iron in solution decreases to below a level concomitant with the economic recovery of uranium. Furthermore, because of the positive correlation between the U02 electrode potential and the phosphte concentration, the electrode will also be of value in the detection of an increase in the phosphate level in solution. When it was incorporated in a suitable industrial probe, the electrode was found to be able to withstand the rigours of the leaching conditions in a large pilot-plant pachuca, and only failed after six weeks&apos; operation.

Jan 11, 1975

"This study examines the problems faced by open pit mine superintendents who make choices about how to direct their materials, either to the waste dump or to the mill. The paper explores the effects of introducing a 10% sampling error and a 0.9-times to 1.1-times sampling bias on positively skewed distributions for precious and base metals, negatively skewed distributions in the case of bulk commodities, and normal distributions as is the case for coal deposits. Parent distributions for each commodity were created on a 25 x 25 m grid using transformations of gold, iron ore, and coal data-sets, spatially based on a nonconditional Gaussian simulation. Ordinary kriging of grades for the three commodities into a 10 x 10 m grid provided the reference case against which the distributions with the sampling error and sampling bias for the commodities were compared. Imposing cut-off grades on the actual-versus-estimated scatterplots of the three commodities allowed the distributions to be classified into components of waste, dilution, ore, and lost ore. Ordinary kriging of values for each deposit type acted as the reference data-set against which the effects and influence of 10% sampling error and 0.9-times to 1.1-times sampling bias are measured in each deposit type. Indications are that the influence of error and bias is not as significant in gold deposits as it is in iron ore and coal deposits, where the introduction of small amounts of error and bias can severely affect the deposit value.IntroductionThe effects of poor sampling and the financial implications for mining companies, traders in mineral assets, and sellers of metal as dore or commodities is documented in a number of studies, the most notable of which is that by Carasco (2004). He examined the financial impact of poor sampling practices in the Chilean copper industry and found that finacial losses due to poor sampling amounted to hundreds of millions of dollars over the life of a mining operation. Holmes (2004) examined the effects of correct sampling and measurement as the foundations of metallurgical balances, and found that revenues from the sales of large iron ore shipments may be profoundly affected by poor sampling practices. In South Africa the way in which sampling of in situ gold-bearing reefs affects the mine call factor has been an ongoing study since the disparity between the estimation of gold in the reef and the actual gold bullion produced was noted by early investigators such as Beringer (1938), Jackson (1946), Sichel (1947), Harrison (1952), and a number of others."

Jan 1, 2017