Search Documents

By Jean J. Tancous

Chromium recovery from wet-blue offal trimmings and shavings can be done with substantial chemical cost gains by incineration at 600° C for 5 hr. Pretreating the offal with 0.5 M Na2C03 and air-drying prior to incineration produce Cr04 .By simply incinerating the offal, without pretreatment, an ash containing water insoluble Cr203 was produced. The Cr203 in the ash was purified by leaching with water. Chromium and crude protein were efficiently extracted from offal using 5 pct Na103, 5 pct H2S04, and 3 pct NaCl at 40° C. This procedure was effective but expensive. Satisfactory leather as to odor, appearance and shrinkage temperature was made from chromium recovered from wet-blue offal by incineration and by extraction. Chromium conservation is possible by recycling chromium liquors and by precipitating chromium from spent tanning liquors prior to combining these liquors with other tannery wastes. Combining chromium liquors with other wastes introduces contaminants that make chromium recovery and reuse difficult. Leaching sludges with H2SO4 produced marginal chemical cost gains. Leather tanned with these solutions had satisfactory shrinkage temperature but the sludge odors and iron contamination were objectionable.

Jan 1, 1979

By George S. Rice

"The emission of hydrocarbon gases from coal beds and contiguous strata causes many accidents in coal—mine workings, the number of fatalities so caused being second only to those due to falls of roof. Gases tend to increase in amount with depth of coal mining, hence the danger of explosion is increased with depth. The pressure of the gas in virgin—coal areas at a distance from mine workings likewise tends to increase with depth from the surface, probably due to corresponding increase in hydraulic head and possibly, when the gas is held in nonporous formations, to greater ground pressure. The rise in gas pressure with depth under usual conditions is shown in wells drilled from the surface and in some coal fields in drill holes into the face of workings; however, under normal conditions of coal formation gas does not issue into workings under high pressure because the coal and adjacent strata have many bedding and joint planes which allow the gas to escape freely at the face of the workings. The rare occurrence of instantaneous outbursts of gas, with violent effects referred to later, constitute the exception.Variations of volume and pressure of fire-damp or methane found in different coal beds by wells at a distance from mine workings, are analogous to variations in volume and pressure of natural gas found in different gas and oil sands, although in general the pressure tends to increase with the depth. Sometimes, however, in tight sands higher in the formation the pressure of gas therein is abnormally high, and on drilling the well deeper gas in the lower strata may be found at lower pressure."

Jun 1, 1934

By Jack Wright

The analysis of water produced with crude petroleum has interested oil producers since inception of the industry. Records of the first analysis of mineralized water produced from an oil-productive formation are obscure, and references to the first use of brine analyses to assist in solving problems of petroleum production are not available in the technical literature. However, many early reports of the Federal Bureau of Mines5-8 and Federal Geological Survey,9-11/ as well as articles in engineer and geological journals12-14/ placed special emphasis on the importance, interpretation, and application of water analyses. One of the earliest applications of water analyses, and still a major one today, is for identification of intrusive waters in oil wells. This may be done by comparing the chemical constituents of a sample of water indigenous to the oil-productive formation with those of samples from upper, water-bearing formations within the same general area. Some earlier investigators recognized the need for Analyzing samples of all waters encountered in drilling operations. Ambrose15/ stated, in part, "In wells being drilled, the engineer should grasp every opportunity to get a true sample of water from each sand. . .," and, "The waters of each oil field are chemically different from those of another field." The validity of the latter observation and the importance of the former one have been borne out by comparing the results of analyses of many samples and noting the differences in relative concentrations of like constituents of waters from the a geological formation in different localities or oil pools.

Jan 1, 1957

By Edward L. McHugh, Charles Sabine, David G. Long

While less than 1% of reported mine accidents are associated with slope stability problems, slope failure accidents were responsible for about 15% of U.S. surface mine fatalities between 1995 and 2003. Small rockfalls, which may involve hand-sized rocks weighing only a few pounds, can cause fatal injuries to workers away from the protection of large machinery. Massive highwall failures containing a million cubic yards of material or more can be fatal even for heavy-equipment operators. As part of an ongoing study at the Spokane Research Laboratory, several remote sensing technologies are being evaluated as tools to assess slope stability and monitor slopes for hazards. An interferometric radar device capable of detecting very small displacements on slopes has been assembled and tested. Radar techniques can provide new tools to augment current methods for monitoring ground control hazards in mines.

[RESULTS OF THE PRIMARY CONVENTIONAL PERFORMANCE AND COST MODEL OF THE UNIT OPERATIONS OF UNDERGROUND PERCUSSIVE DRILLING AND BLASTING]

Jan 1, 1977

Recommendations from 44 mining industry workshops are summarized and reviewed in the context of Bureau of Mines research and development programs on-going during the period 1974-1977. Approximately 1,000 specific recommendations for research and development are summarized in a systematic and comprehensive format appropriate for review by mining research and development program managers. Relevant Bureau of Mines research programs are briefly described and some opportunities for future research and development are identified.

Jan 1, 1979

By Ralph H. Espach

Wyoming contains many petroleum and natural-gas fields, and more than 250 geological structures have been mapped; however, only about 85 have been found (July 1938) to contain petroleum or natural gas, or both, in commercial quantities. To January 1938 approximately 434 million barrels of oil and 915 billion cubic feet of gas have been produced, and it was estimated that proved oil reserves in Wyoming amounted to 300 million barrels.' The Salt Creek field, the largest in the Rocky Mountain area, alone has produced 64 percent of the State's oil and 46 percent of its gas. This field ranked thirteenth among the producing fields of the United States in total cumulative production as of January 1, 1938. On this basis it ranks with the Kern River and Huntington Beach fields of California and the Butler County fields of Kansas. The Salt Creek field has declined in relative importance; in 1937, while still the largest oil-producing field in the State, it produced 31 percent of the oil and 11 percent of the gas extracted from all wells in Wyoming.

Jan 1, 1941

By R. E. Heithecker

In Kansas, almost every oil well drilled into a limestone formation is treated with hydrochloric (muriatic) acid upon completion. This is done to increase the potential capacity of the well and thereby increase its "daily allowable" production (see p. 9 ), to shorten the time required to produce the recoverable oil, and to increase the quantity of oil recovered ultimately from the reservoir. The porosity and. permeability of limestone formations seldom are uniform throughout the proved area, consequently the production capacities of completed wells vary considerably. Acid treatment of wells tends to increase production capacity and to equalize potential capacity. If offset wells already have been treated with acid, new wells usually are treated to protect the property on which they are drilled against drainage. Even though competitive conditions do not exist in a field, it

Jan 1, 1939

By Merwin H. Howes

Gnome shaft, situated about 24 miles southeast of Carlsbad, N. Mex., was designed and sunk by the U.S. Atomic Energy Commission for conducting a peace- time experimental nuclear explosion in the thick salt beds of the Permian Salado formation. Excavation was started July 1, 1960, and completed July 26, 1961. The 10-foot diameter shaft, lined with concrete through the rock section, was sunk 1,216 feet. A drift was driven approximately 1,140 feet on the 1,200- foot level terminating in a shot chamber. On completion of 100 feet of shaft, by means of a truck-mounted crane, facilities were installed for conventional sinking. About 709 feet of rock and 506 feet of salt were encountered in the shaft. Salt beds at this place are reported to be over 1,200 feet thick. The overlying rock section varies greatly in composition and thickness of beds and contains a 28-foot bed of water-bearing dolomite. The aquifer was sealed to facilitate shaft sinking and to prevent water-seepage damage in the salt section of the shaft. Sealing was accomplished by grout injection through holes drilled into the aquifer and by grouting behind the concrete liner.

Jan 1, 1963

By Merwin H. Howes

Gnome shaft, situated about 24 miles southeast of Carlsbad, N. Mex., was designed and sunk by the U.S. Atomic Energy Commission for conducting a peace-time experimental nuclear explosion in the thick salt beds of the Permian Salado formation. Excavation was started July 1, 1960, and completed July 26, 1961. The 10-foot diameter shaft, lined with concrete through the rock section, was sunk 1,216 feet. A drift was driven approximately 1,140 feet on the 1,200-foot level terminating in a shot chamber. On completion of 100 feet of shaft, by means of a truck-mounted crane, facilities were installed for conventional sinking. About 709 feet of rock and 506 feet of salt were encountered in the shaft. Salt beds at this place are reported to be over 1,200 feet thick. The overlying rock section varies greatly in composition and thickness of beds and contains a 28-foot bed of water-bearing dolomite. The aquifer was sealed to facilitate shaft sinking and to prevent water-seepage damage in the salt section of the shaft. Sealing was accomplished by grout injection through holes drilled into the aquifer and by grouting behind the concrete liner.

Jan 1, 1963

By Richard B. Moore

This bulletin presents a summary of available information regarding the sources of uranium, radium, and vanadium, the methods used in treating the ores, and the uses of the finished products. In particular the paper describes the ores found in the United States, giving especial attention to those characteristics of the ores and the conditions of their occurrence that affect mining and treatment. ACKNOWLEDGMENTS. In the preparation of this bulletin a number of persons rendered assistance by furnishing information and by making it possible for us to visit the carnotite deposits in western Colorado and eastern Utah at a time of the year when without this assistance it would have been difficult to obtain satisfactory results. We desire to express our thanks to the following persons: Henry Hall, W. L. Cummings, T. V. Curran, K. D. Hequembourg, David Taylor, H. C. Brown, Forbes Rickard, George W. Alsdorf, Dr. Herman Fleck, Orr J. Adams, C. S. Cherrington, Newt. Stewart, O. B. Willmarth, Angus Cameron, George A. Head, and Lorimer Bros.

Jan 1, 1913

By D. Randolph Berry

The objective of this program was to develop a system to extinguish coal mine fires by remote sealing of the underground passageways. The system developed had to be versatile enough to function under a wide range of operating conditions, including large variations in passageway geometry, depth of mine, water conditions, both in the mine and at the surface, and rubble in the mine passage. The system developed had to include instrumentation for the remote probing of the passageway prior to sealing, a system for sealing the mine passages, and instrumentation for remote monitoring of the quality of the seal during and after construction. These objectives were successfully achieved during this program. The remote mine sealing capability of the system was satisfactorily demonstrated in a field test conducted at the Eastern Associated Coal Corporation Federal No, 1 Mine in Grant Town, West Virginia.

Jan 1, 1973

By Michael A. Anuta

This report describes the potential for utilization of satellite observations for remote sensing of mine waste disposal areas. Four study sites consisting of metal and nonmetal mining areas in different climatic and physiographic regions of contigous United States were used in this investigation. The mine waste disposal sites consisted of mining of phosphates in Florida, copper in Arizona, silver in Idaho, and coal in West Virginia. Landsat satellite multispectral scanner observations were used together with aerial photographs, ground surveys, U.S. Geological Survey maps, and other ancillary information. Landsat digital data were categorized using automated supervised classification algorithms and an image analysis system. Detailed description of automated classification techniques employed and the accuracy attained is provided together with the results of manual interpretations. The inventory of areas distrubed for phosphate mining and a change detection investigation for-Polk County Florida were also undertaken during this study.

Jan 1, 1982

By Charles J. Haas

The objective of this research was to investigate the interaction phenomena of rock and types of rock bolts to develop design principals for using grouted roof bolts. The investigation was to determine the effectiveness of grouted bolts in resisting lateral displacement and axial separation along fracture planes, and also to determine if grouted bolts eliminate the axial tensile stress near the anchor and the resulting rock fracture. The first year's effort involved defining the post-tensioning response of grouted bars and determining the amount of shear resistance generated by conventional and resin-grouted bolts. A finite-element analysis showed that if the rock and resin grout behave in an elastic manner, the post tensioning of a grouted bar will affect mine roof stability only if movement occurs near the collar. An experimental shear test program revealed that both conventional bolts and resin-grouted reinforcing bars significantly increase shear resistance along fracture or bedding plane when the average normal compressive stress on that plane is low (in the order of 25 psi) and when the bolt is oriented so that the shear displacement tends to lengthen the bolt. An increase in shear resistance is also noted at the higher normal pressure of 250 psi; however, the increase is small compared to the corresponding shear resistance without a bolt. Conventional bolts oriented so that they tended to loosen with shear displacement added no significant shear resistance.

Jan 1, 1974

By Harold J. Bennett

The purpose of this study was to develop methods for the financial evaluation of mineral deposits. This includes the selection of the best alternative mining and processing methods and production rates. This was done by performing a financial evaluation through computer simulation using sensitivity and probabilistic risk analysis. The criterion used to measure the relative advantages of these investment and operating alternatives is the discounted-cash-flow rate of return. Included is a description of the theory and methods used in the probabilistic analysis approach, which is based on the premise that the expression of a range of values in establishing an estimate for a parameter is more realistic than the choice of a single value. Numerous simulations are made using randomly selected values of the input parameters resulting in a frequency distribution of the rates of return and their relative probability of occurrence. The sensitivity analysis method is described and combined with the probabilistic analysis to interrelate mineral reserves, capital investments, operating costs, and production rates. The ability to vary these input parameters on successive runs has permitted the selection of the best alternative mining and processing methods and production rates for a given mineral deposit. For illustrative purposes the evaluation of a mineral deposit was performed using three alternative mining and processing methods at three different quantities of resources and various production rates and prices. The computer program used in this analysis was written in FORTRAN II for maximum compatability and should run without modification on most computers having BK (8,000-word) core memory, a card reader, and printer (120 characters per line).

Jan 1, 1970

By David A. Monaghan

This report describes instrumentation which is part of a system for extinguishing mine fires by pumping material through surface boreholes in order to seal off all underground passageways leading to the fire area. Major instrumentation systems include a closed circuit television probing system and an acoustic seal checking system. The latter consists of a speaker probe, a receiver probe and related signal processing equipment. All probes can be winch-deployed down a 6-inch diameter borehole. The CCTV unit can be rotated 360 degrees in the horizontal plane, and contains sufficient lighting to reliably assay conditions for sealing or rescue within a 200 foot radius. The acoustic seal checker monitors the completion of a seal as it progresses by use of probes lowered through boreholes on either side of the seal.

Jan 1, 1977

By GLADYS G. HEFFNER, William H. Waggaman, Edwin A. Gee

Thallium is one of the rare and relatively neglected elements that has recently assumed conspicuous importance. This element is widely distributed in nature but occurs in such minute quantities in most rocks and minerals that its recovery at present is only commercially feasible as a byproduct of other industries. World War II, with its unprecedented demand for products having special or unusual properties, led to a study of a number of the rarer elements that previously had been given comparatively little attention for one or more of the following reasons: 1. 2. Limited knowledge of properties. Small quantitios present in available raw materials. 3. High cost of concentration and recovery. Some of those rare elements, either alone or in the form of compounds, have already proved of such value for certain military and industrial purposes that their extraction from ores and waste products, oven at high cost, is fully justified. On the othor hand, further investigation of their character- istics, discovery of more adequato sources, and improvement in methods of con- centration and recovery would greatly broaden their field of usefulness and establish new and expanded industries. The current market for some of these elements exceeds the available supply. One of the functions of the Bureau of Mines is to study the properties of such elements in greater detail, locate the most promising raw materials from which they can be derived, and work out methods of extraction that will render the recovery of such elements more economical. The purpose of a serios of information circulars on the raror elements is to present in condensed form the facts and data so far available. This information may serve as a basis in planning more complete investigations loading to a full utilization of such elements.

Mar 1, 1950

By Hon-Yim Ko

The properties of coal from the Pittsburgh seam, procured from the Bruceton and Federal No. 2 Mines were found to be similar. Strength and stiffness properties of Beehive Mine coal were determined and the material found to be isotropic. Mechanical, index and geologic properties of roof and floor coal measure rocks from Beehive mines were measured and correlated. Analytic formulations are given for coal creep under uniaxial loading, while triaxial creep is being investigated. Results of testing of coal model structures are compared with predictions from using several material models.

Jan 1, 1976

By W. P. Diamond

The Bureau of Mines has been involved in the drilling of vertical, horizontal, and directional coalbed gas drainage boreholes for mine safety since 1964. In that time, boreholes have been drilled in most of the major coal regions of the United States under a wide variety of geologic conditions. Many of the geologic conditions that occur in the coal measures are detrimental to gas drainage; others may be beneficial. Analytical techniques to determine the gas content of coal samples and evaluate regional trends of gas distribution have been developed. Drilling techniques that maximize the acquisition of coalbed gas data and geologic information have been determined. Although some of the geologic factors influencing the placement and potential success of coalbed gas drainage boreholes have been reported in papers on individual projects, a complete, systematic compilation has not previously been available. The objective of this paper is to pro- vide information on specific geologic factors that should be considered prior to, during, and after the drilling of coalbed gas drainage bore-holes. Many of the commonsense considerations that have been learned through many years of Bureau of Mines experience, but have generally not been reported formally, are included for those who may be considering coalbed gas drainage drilling for the first time, or who have not had the opportunity to encounter a substantial number of geologic situations.

Jan 1, 1982

By F. Matanzo

[Nine wire rope terminations were pull tested and fatigue tested to destruction to measure the termination efficiency and relative fatigue life. The terminations were selected on the basis off mine site visits and the specimen were assembled in a manner similar to industrial slings. To measure a termination's sensitivity to poor workmanship, both standard and modified assembly specimen were tested. Lang and Regular construction of the 6x19 and 6x37 class wire ropes were used in diameters of 13 mm (1/2 in.), 19 mm (3/4 in.), 25 mm (1 in.), 38 mm (1 1/2 in.), and 51 mm (2 in.). In static pull tests rope class, construction, and diameter interacted with the termination to influence the efficiency of the termination. In axial fatigue tests using only the 6x19 class rope, the effect of rope construction was negligible since failure was primarily dependent on the termination type. The Swaged Socket, a termination requiring a high capacity hydraulic press, gave the best overall performance in terms of efficiency and fatigue life. The short body length of the Zinc Poured Socket (RR-S-550) was attributed with the short fatigue life of this termination. The use of thermosetting resins as a replacement for zinc was demonstrated successfully for some socket designs. The fatigue life of the termination, expressed as a percentage of the fatigue life of the wire rope, was shown to be a guide for the retirement of the wire in these applications where the wiry' rope is primarily in axial loading.]

Jan 1, 1978