Search Documents

By P. C. Good

The work reported here was undertaken by the Federal Bureau of Mines to investigate new methods of preparing high-purity metal. Tungsten hexachloride was prepared by direct chlorination of scrap tungsten metal and by treating tungstic oxide with carbon and chlorine. The resulting tungsten hexachloride was purified by distillation and reduced win: sodium, magnesium, or hydrogen. The metal prepared by these techniques was at very high purity after arc melting but of variable quality prior to arc meIting. Metal recovery ranged from about 40 to 90 percent of theoretical values, It was found possible to deposit a smooth, dense coating of high-purity tungsten on the inside of a heated tube by vapor-phase reduction of tungsten hexachloride at reduced pressure.

Jan 1, 1961

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

To increase safety and productivity in mining , the potential uses and hazards of rigid foam were investigated by the Bureau of Mines Experimental Coal Mine . This research resulted in the development of chemical formulations , spraying equipment , and application procedures that permit safe and effective use of urethane foams for improving mine ventilation , for reducing weathering of mine rock and steel , for constructing seals in fire areas , and for thermal insulation .

Jan 1, 1964

By Harry G. Dosh

Sillimanite, kyanite, and andalusite are aluminum silicates having the same chemical composition (Al2SiO5) and are used in the ceramics industry for the manufacture of high-grade refractories. Natural sillimanite with added corundum or other alumina to just short of mullite (3Al2O3 -2SiO2) proportions is unequalled for jobs wherein strength at high temperatures, resistance to spalling, and resistance to slagging by acid slags are desired. High-grade porcelain ware also requires these minerals. At the same cost, sillimanite would be preferred for most uses, but the lack of any large source of sillimanite bas given economic preference to kyanite or andalusite for special refractories and high-grade porcelain wares. Sillimanite-bearing schists were observed in Spartanburg County, S. C.; as early as 1937 by D. Hoye Eargle, geologist with the U. S. Soil Conservation Service. The mineral was not identified until 1942, when Miss Jewell Glass, of the U. S. Geological Survey, examined several of the deposits. This identification was confirmed in 1943 by Dr. Laurence L. Smith, of the University of South Carolina, when he examined the Spartanburg County deposits and found numerous additional occurrences of sillimanite schist in Greenville County. Subsequent work by the Bureau of Mines and the South Carolina Geological Survey has been responsible for the location of additional sillimanite-rich schist deposits in Spartanburg County. Between October 1, 1948, and November 21, 1948, the Bureau of Mines conducted an exploratory diamond-drilling project on the John Gideon property in the southeastern section of Spartanburg County (fig. 1) and drilled a total of 681.7 feet in six holes. Drilling indicated that the deposit is relatively shallow, as no ore was cut below the zone of weathering.

Jan 1, 1950

By D. Harrington

Although it is impossible to give definite final figures at this time on Nation-wide accident occurrence in 1933 , enough data are at hand to indicate that the progress in safety in the mining industry, which first became apparent in 1930 and was accentuated in 1931 and 1932 , was continued and much improved in 1933. This improvement was of considerable magnitude in mining both bituminous coal and anthracite but was not so great in other branches of the mining industry . While the volume of work done in all phases of mining increased in 1933 over that in 1932 , the exact amount of the increase is not yet known . Usually increased activity in mining is accompanied by even greater increase in the rate of occurrence of accidents to the workers , but happily it appears that this " rule " was not operating in 1933 --at least in the coal -mining industry .

Oct 1, 1934

By A. W. Henderson

This investigation was performed to develop chlorination methods for extracting tungsten from scheelite and from an ore concentrate containing a mixture of scheelite and wolframite. On a laboratory scale with proper temperature control using elemental chlorine, over 90 percent extraction of tungsten is achieved. Carbon and sulfur dioxide were studied as reducing agents. The effects of salts such as calcium fluoride and sodium chloride were studied as additives to increase extraction and to reduce impurities in the volatile tungsten chloride product. Sodium chloride reacts with ferric chloride to form a nonvolatile double salt; whereas the chlorides and oxychlorides of tungsten are volatile and consequently condense free of iron. Separation of tungsten from molybdenum from an equal molar mixture was successful by fractionally distilling the oxygen-free chlorides and by selectively condensing the oxychlorides. Yields of 60 and 80 percent, respectively, were achieved for separating the less volatile tungsten chlorides containing less than 0.5 percent molybdenum.

Jan 1, 1965

By M. G. Zabetakis

Amyl nitrite (C5H11NO2) is a pale-yellow liquid with an ethereal fruity odor and a pungent aromatic taste. Its use in first-aid treatment of cyanide poisoning has been suggested by Chen and his coworkers. Although not the most effective treatment, it is the only one that does not require intravenous injections and is, therefore, very suitable as a preliminary measure, which only involves breaking a capsule near the patient's nose until intravenous injections can be given. In the case of the sodium nitrite -sodium thiosulfate treatment, for instance, such injections require about 15 minutes. As amyl nitrite "Pearls" (small capsules containing liquid amyl nitrite) are placed in many first-aid kits by various companies that handle, store, or use hydrogen cyanide gas, it appeared advisable to investigate the explosion hazards of this material in air and oxygen. Accordingly, tests were made to determine the limits of flammability, temperature range of flammability of amyl nitrite saturated with air and with oxygen, and minimum ignition temperatures of this material in air and in oxygen.

Jan 1, 1952

By M. M. Fine

A preliminary mineral-dressing study of five samples of East Texas limonitic brown iron ores was conducted as part of the Bureau of Mines program to develop and extend domestic resources of iron ore. The samples were considered to be typical of ore currently being mined and beneficiated by the Lone Star Steel Co. and Sheffield Steel Co. The objective of the research was to investigate those mineral-dressing unit operations that might recover some of the fine iron lost in current industrial wastes or perhaps improve the recoveries when applied to the ores as well. Since current industrial beneficiation practice yields a washed limonite analyzing 41 to 45 percent iron, higher grade concentrates were not sought in this laboratory study. Laboratory investigation included washing and sizing, reduction roasting, and subsequent magnetic separation of the finely ground roasted materials. The results showed that laboratory recoveries of over 80 percent of the iron were possible, for the ores investigated, at concentrate grades comparable to those expected from cur-rent industrial beneficiation practice. ACKNOWLEDGMENTS Acknowledgment is made to the Lone Star Steel Co. and Sheffield Steel Co. for supplying the brown iron-ore samples on which this research was conducted.

Jan 1, 1956

By F. S. LOTT, I. S. CULVER

The number of petroleum refineries in the United States decreased during 1948 from 390 to 375, continuing the trend to fewer units of larger individual capacity that has persisted since the peak in number of plants was recorded on January 1 , 1936. Large - scale construction of new processing facilities continued through 1948 with a resultant gain in daily crude-oil throughput capacity of installed equipment from 6,034,252 barrels on January 1 , 1948 to 6,438,995 barrels on January 1 , 1949. The capacity of the average refinery to process crude oil therefore increased during 1948 from 15,472 barrels daily to 17,171 . The principal areas of expansion of facilities were the strategic seaboard districts of the Texas and Louisiana Gulf Coast and the East Coast , and the important Indiana , Illinois , Kentucky, etc. , district that supplies markets in the upper Middle West region . These four districts accounted for 79 percent of the total new capacity added in the United States in 1948. The relatively small petroleum- refining industry of the Other Rocky Mountain district experienced a vigorous expansion in 1948 that will continue during 1949 . Capacity building on January 1, 1949 , amounting to 341,500 barrels daily, was 25,750 barrels lower than the comparable total on January 1 , 1948, but was the second highest on record . New construction was heavily concentrated in the Texas Gulf, East Coast , and Indiana -Illinois

Sep 1, 1949

By A. E. Isaacson

The U.S. Bureau of Mines determined the effect of common sulfide minerals on the corrosion rates of various types of ferrous alloy grinding media. Data obtained from this study will aid in determining the contribution of any electrochemical reactions between sulfide minerals and grinding media to the total grinding media consumption. Common sulfide minerals used in this study were chalcopyrite, galena, and sphalerite. In the presence of oxygen, chalcopyrite was found to increase the corrosion rate, galena was found to decrease the corrosion rate, and the effect of sphalerite was dependent upon the type of grinding media. Possible electrochemical reactions of these minerals in the presence of grinding media are suggested.

Jan 1, 1989

By Henry W. Busch

Determination of the aldehyde content of Diesel-engine exhaust gas has proved rather cumbersome and unsatisfactory when carried out in its entirety in field investigations; therefore, studies were conducted with a view to developing methods by which samples might be collected in the field and trans-ported to the laboratory for analysis. Experience also indicated that aldehyde samples collected in water solution and then transported to the laboratory sometimes underwent serious changes in composition if several days elapsed between sampling and analysis. Polymerization of the aldehydes, which takes place readily in dilute aqueous solutions, may have been the cause of such changes. Because of these difficulties, experiments were conducted to find a suitable stabilizer or preservative for dilute aqueous solutions of the aldehydes that occur in Diesel-engine exhaust gas, so that in field studies a known volume of gaseous sample might be collected and brought into contact with water, and the resulting solution of aldehydes analyzed in the laboratory at some later time with reasonable certainty that the results would represent the composition of the original sample,

Jan 1, 1949

By R. M. Winslow

"The phosphorus content of an iron ore is a determining factor as regards the value of the ore and also its metallurgical treatment. If some method of treatment, such as concentration, leaching, etc., could be used and the phosphorus con- tent of the ore reduced, it would be an important advancement in the iron mining industry towards the utilization of high phosphorus ores. Large bodies of material toe high in phosphorus to be marketable under present conditions would be made available, and a great deal of ore from the Cuyuna Range and other places, which is relatively high in phosphorus but otherwise suitable for making spiegel, could be reduced in phosphorus content sufficiently to permit its use in furnaces producing speigel.The form in which phosphorus occurs in iron ore is a much disputed question and it probably varies with the type and location of the ore. The statement has been made that ore piles on long exposure to the atmosphere often decrease in their phosphorus content. (Emmons, S.F. - Ore deposits, 1913, p. 652; Leith, C.K., Mesabi iron bearing district, U.S.G.S. Monograph 43, 1903, p. 275) There is described below experiments on the leaching of iron ores high in phosphorus, to determine whether it was economically possible to reduce the phosphorus content appreciably by leaching. As the research had a practical as well as a theoretical application, only low concentration of acids and alkalies were used.A number of variables were tried, among these being: (1) The solvent used, (2) strength of the solvent, (3) volume of solution used, (4) time ore was agitated (5) type of ore, and (6) screen size of the ore. The amount of ore taken was kept constant."

Jul 1, 1921

By G. R. Hopkins

A fifth successive record in fuel efficiency was established by the petroleum-refining industry in 1937, when the average heat requirement per barrel of crude oil run to stills was 554,000 3. t. u. compared with 597,000 3. t. u. in 1936. These amounts represent roughly the heat ob¬tainable from a tenth of a barrel of fuel oil (see fig. 1). Innumerable factors can influence heat consumption at rep aeries, but only a few are important enough to be subject to statistical measurement. Foremost of these is the ratio of runs to capacity, it being generally recognized that because the fuel demands for other than stills are comparatively inelastic, total heat requirements do not increase in direct proportion to crude runs. Thus, in 1937, crude runs of 1,183,440,000 barrels wore 11 percent higher than in 1930; the average operating ratio was 93 percent compared with 79 percent in 1936; but the total heat requirement increased only 4 percent, or from 639,149 billion 3. t. u. in 1936 to 663,966 billion 3. t. u. in 1937.

Jan 1, 1938

By R. P. Beyer

As part of its thermodynamic investigations of mineral compounds, the Bureau of Mines has written an algorithm based on Newton's method for solving for the characteristic Debye temperature of a compound, from heat capacity and temperature data. A listing of a FORTRAN IV program based on this algorithm, for calculating Debye temperatures given heat capacities or for calculating heat capacities given Debye temperatures, is available from the author upon request.

Jan 1, 1981

By P. M. Gruzensky

In view of some of the outstanding properties of chromium, considerable effort has been made in recent years to prepare the high-purity metal in ductile form. The object of this investigation was to obtain such metal by electrolysis of chromic acid solutions and to determine the conditions that yield optimum results. The apparatus is described, as well as the parameters that received consideration. Ion-exchange resins were employed to remove cation impurities from the electrolyte. Tensile specimens prepared from the electrodeposits by arc melting, press forging, swaging, and drawing, were ductile at room temperature. INTRODUCTION Metallic chromium displays an exceptionally high resistance to corrosion, oxidation, and wear at elevated temperatures. Although these properties are utilized to some extent when chromium is alloyed with other metals, such as in stainless steels, high-chromium alloys and pure chromium are not employed as engineering materials because of a serious lack of ductility and impact resistance at room temperature. Because high-chromium alloys appear promising as refractory metals for applications such as in gas turbines, much interest has been shown recently in the preparation of uniformly ductile chromium and in determining which factors contribute to its brittleness.

Jan 1, 1957

By A. B. Cecala

A new prototype bag nozzle system has been designed under a Bureau of Mines contract to reduce dust generated during the bagging operation on fluidized air baggers. A field analysis of the new system has shown that the bag operator's dust exposure was reduced 83 pet. The amount of blowback was reduced 89 pet, which corresponds to a significant product savings. The new prototype system has been operating for a substantial period of time with no major problems.

Jan 1, 1984

By John C. Ferm

This report contains a summary of Phase I and complete results of Phase II portions of a study of geologic factors associated with roof falls in mines on the Pocahontas #3 coal seam in southern West Virginia and southwestern Virginia. Principal objectives of Phase I was the selection of five mines that best portrayed the spectrum of roof and mining conditions and Phase II consisted of a measurement and documentation program for each of the five mines. The documentation measurement program included reconnaissance mapping, detailed mapping, joint measurements and coring roof rock. 1.2 PHASE I RESULTS The results of Phase I consisted of the selection of the following five mines for detailed study: Virginia Pocahontas #3 (Island Creek Coal Company), Bishop (Consolidation Coal Company), Shannon Branch (Allied Chemical Company), Keystone II (Eastern Associated Coal Company) and Macalpine-East Gulf (Westmorelenad Coal Company). In addition, Phase I results, which were based on questionnaire data, indicated that the kind of rock in the roof --gray sandstone, crystallized sandstone, laminated sandstone and shale, grey shale, slickensided shale, and rider seams could be associated with good and bad top areas. Also presence of vertical separations, bolt length, entry and cross-cut width, length and torque on bolts and depth of overburden seemed to be related factors. These data provided a focus for the Phase II measurement program.

Jan 1, 1975

By Homer J. Ballinger

The Rex mine is one of several zinc deposits in Ozark and Howell Counties, Mo. It is the second of these deposits investigated by the Bureau of Mines in an effort to demonstrate reserves of sulfide ore underlying the shallow carbonate ores from which the district's major production has come. The initial investigation was made during 1945-46 on the Alice mine, Ozark County, Mo.21 The investigation reported herein was conducted during 1947. The Rex open pit is about 250 feet long, 100 feet wide, and about 25 feet deep (average). Three caved shafts are evident in the bottom of the pit, but the extent of the workings from these shafts is not known. The Bureau of Mines drilled five churn-drill holes in and around the Rex pit to test the grade and the vertical and lateral extent of the deposit. Two of the holes indicate notable zinc mineralization ranging from less than 1 to more than 10 percent metallic zinc, but largely in the oxidized condition.

Jan 1, 1948

By Raja V. Rarnani, Robert L. Frantz

"Mining is one of the oldest of human occupations. The awareness of occupational illnesses associated with mining, even in ancient times, is evident from the writings of Hippocrates (460-370 BC), Pliny and Elder (AD 23-79), and Galen (AD 131-210). Georgius Agricola (1494-1535), in his De Re Metallica, refers to the diseases of miners and the need for their control through good planning and operating practices and responsible management (Schwerha, 1989). Coal workers' pneumoconiosis (CWP), often called Black Lung disease, is an occupational disease which results from inhalation of coal mine dust which usually contains relatively small amounts of free crystalline silica.A pneumoconiosis is best defined as the accumulation of dust in the lungs and the tissue's reaction to its presence [Lapp and Castranova, 1993]. Silicosis is the name given to the fibrotic disease of the lungs caused by the inhalation of dust containing silicon dioxide, primarily in the free crystalline form. Silicosis is the older and more well known of these mineral pneumoconioses. In contrast, CWP was not recognized as different from silicosis until the pivotal work of Collis and Gilchrist [1928].The U.S. Bureau of Mines (USBM) still regards worker exposure to respirable aerosols in mines as the most serious health problem in mining [USBM, 1994]. The National Institute of Occupational Safety and Health (NIOSH) is considering recommending a reduction in the standard for occupational exposure to respirable coal mine dust from 2 mg/m3 to 1 mg/m3 [NIOSH, 1993]. The Mine Safety and Health Administration (MSHA) may require new criterion for sampling procedures in the mine that would evaluate the ambient dust concentration in the mine atmosphere based on a single sample, instead of the current practice of averaging five samples (MSHA, 1992; Ramat* 1993). Several high-production longwall mining faces currently have extreme difficulty meeting the existing dust standards, and some already operate at reduced production levels to achieve mandated levels [USBM, 1993]. The importance of adequately protecting the miners from high concentrations of coal mine dust, as well as of reducing the incidence and severity of the Black Lung disease, cannot be overemphasized. The importance stems, first and foremost, from the humanitarian viewpoint and, second, from the perspective of the overall welfare of the coal industry.The histopathologic hallmark of CWP is the coal macule (Balaan, Weber and Banks, 1993). Autopsy or open lung biopsy reveals the coal macule to be an amorphous mass of coal particles, dust-laden pulmonary macrophages, reticulin, and collagen. No pathognomonic signs or symptoms identify workers with CWP. A CWP diagnosis requires that the worker experienced the appropriate dust-exposure setting (e.g., underground coal mining) and duration (usually 10 years or more) and, has the characteristic chest radiograph. Based upon the International Labour Organization (ILO, 1980) international classification, pathologists and radiologists have established case definitions for characterizing the pathology and the appearance of CWP on chest radiography (Weeks, 1993). CWP appears in two principal forms: simple, with small opacities, and complicated, with opacities larger than 10 mm in diameter. For all practical purposes, diagnosis of CWP in the living miner is wholly dependent upon the chest radiograph interpretation."

Jan 1, 1995

By Ronald D. Hill, Elmore C. Grim

1.In 1972 over 595 million tons (51+0 million metric tons) of bituminous coal were mined; 49% of this tonnage was obtained by surface mining methods. Authorities have predicted that the tonnage of surface mined coal will increase in the future, especially since oil and gas resources are becoming limited. 2. Demands for clean air have increased mining activities in the low-sulfur coal deposits in the West. Pollution problems arising from these operations will be considerably different than those found in the East. The deposits are located in arid to semi-arid regions. Coal seams are generally aquifers and are a principle source of fresh water. Therefore mining may result in alteration of groundwater distribution patterns by aquifer disruption. In general, pollution problems associated with western mining are not well characterized. 3.Since any disturbance of the surface will alter the environment in the vicinity of the disturbance, pre-mining planning is a prerequisite to any environmentally successful surface mining operation. If properly carried out, the adverse social, economic, and environmental effects of coal surface mining will be minimized. Certain land areas will be unsuitable for surface mining where: a.Reclamation is not physically or economically possible. b.Mining is incompatible with existing land use plans. c.The proposed mining area is of critical environmental concern. Core drilling is the most satisfactory method of obtaining accurate information for pre-mining planning. 4. Unaccountable strip mining in the past has created problems that are still present today. Contour mining methods that involve the indiscriminate dumping of overburden on the downslope is one of the largest single sources of sediment from strip mining. However, land disturbed by strip mining can be reclaimed. Techniques have been and are being developed by which mining and reclamation are integrated into a single operation. Mountain top removal, head-of-hollow fill, and block cutting are examples in contour surface mining. These methods drastically reduce pollution problems associated with contour stripping.

Jan 1, 1974

By V. A. Nieberlein

This paper presents the results of research undertaken to recover titanium and columbium by low-temperature chlorination of low-grade columbium-bearing ilmenite concentrates, and to simultaneously remove chlorinated impurities from the volatile chlorides without resort to distillation. Coke-reduced ilmenite was chlorinated at 400° to 500° C., and the resulting TiC14 was free of most impurities before condensation. A heated purification column was used wherein various packing materials reacted chemically or physically with the impurities which passed through them in the vapor phase. A nearly water-white TiC14 product was obtained directly. The principal impurities in the titanium tetrachloride were: 0.02 percent Fe, 0.01 percent V, 0.05 percent A1, 0.04 percent Si, and 0.07 percent Cb. This is a less pure product than commercial TiC14. Most of the columbium was recovered as crude CbC15, requiring further refining.

Jan 1, 1960