Search Documents

By Herbert R. Appell

Urban refuse, cellulosic wastes, and sewage sludge have been converted to heavy oil by heating under pressure with carbon monoxide and steam. Conversions of the organic matter to oil, water, and gas have averaged near 90 percent at temperatures of 250° to 400° C and pressures of 1,500 to 5,000 psi. The yield of oil, based on the dry organic matter of the waste materials, is usually near 40 percent. This is the equivalent of more than 2 barrels of oil per ton of dry, ash-free waste material. The oil from urban refuse and cellulosic wastes has a sulfur content near 0.1 percent. This low sulfur content makes the oil from refuse a desirable source of fuel oil.

Jan 1, 1970

By R. M. Santmeyers

This paper presents one of a series of digests of foreign mining legislation and curt decisions that is being prepared in advance of a. general report relative to the rights of American citizens to explore for minerals and own and operate mines in various foreign countries. This interpretation of the mining legislation of Madagascar was prepared from the best information (in French) available in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers, to whom it dill be referred through the courtesy of the Department of State. INTRODUCTION The basic mining law of Madagascar is the decree of 1923, signed at Rambouillet by the President of France on July 19, and published in the Journal Official de Madagascar et Dependances. It has been modified by a number of subsequent laves and regulations, generally of minor importance.

Jan 1, 1933

By M. V. Potter

"In nearly all fields of investigation, research laboratories and routine testing laboratories encounter problems in which the primary determinations involved in the study require the measurement of mechanical vibrations or motions. These vibrations,may be of an oscillatory nature covering frequencies from a few cycles per second up to hundreds of Kilocycles per second, or they may be more or less uniform study nations occurring at rather slow rates. In electrical, or mechanical methods. In the optical case the to cause the deflection of a light beam such that the motion of the mechanican system of the beam can be determined, then by direct the by direct observation on a suitable scale or by recording it’s the electrical methods the motions can be made to changes in resistance, capacity or inductance proportion to the mechanical displacement or electromagnetic means can used to generate directly a voltage that will be porpertuial to the instantaneous vicinity of the vibrations. Other devices are used in a special instance, also but in any cause the electrical methods produce a current that is an electrical counterpart of the mechanical motion, and the motion can then be studied by direct measurements of the current or by recording the current on suitable recording meters or oscillography. Mechanical methods are used in some instance but are generally not as convenient nor as flexible as the optical and electrical methods."

Feb 1, 1943

By Michael A. Trevits

During the time period from 1990-2007, there were 1601 reportable fires that occurred in the U.S. mining industry (an average of 89 fires per year). The leading causes of U.S. mine fires include flame cutting and welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions, and spontaneous combustion. The National Institute for Occupational Safety and Health (NIOSH) is conducting a program of research addressing metal/nonmetal and coal mine fire prevention, detection, management and suppression. In the metal/nonmetal area, work was focused on technology transfer and training, and research to reduce the number of mobile equipment fires and their hazards. In the coal arena, research is underway to determine the root cause of cutting and welding-related fires and to evaluate the effects of ventilation schemes relative to the spontaneous combustion risk in longwall mines. Relative to fire management, research is ongoing on remote mine seal installation and remote mine fire suppression technologies. Finally, research is continuing to develop comprehensive and usable smoke management techniques and to develop mine fire growth models, propagation, and suppression. This paper presents a summary of some of the mine fire research and provides an overview of the next phase of the NIOSH mine fire research program.

Jan 1, 2010

1. In 2002, a total of 2,820 contracting companies reported employment at coal mines to MSHA.

Jan 1, 2004

By R. L. Stein

For the past several years, the Bureau of Mines has been actively engaged in developing two new oxygen self-rescuers through research contracts with private industry. These new oxygen self-rescuers are designed to be carried by a miner while he is at work and are used during emergency escape, supplying high-purity oxygen to the user and, at the same time, absorbing carbon dioxide (C02), The first of the two new self-rescue breathing devices is a 10-minute, self-contained apparatus developed by the Mine Safety Appliance Co, Size and weight of the unit are comparable to the currently used self-rescue devices. The second device, designed and developed by Lockheed Missiles and Space Corp., is 8. 4.5-lb package which supplies 1 hour of oxygen to the miner. Both devices have a canister which contains the oxygen-producing and CO2-absorbing potassium superoxide chemical, a breathing bag, a bite-type mouthpiece, noseclip, goggles, and hoses connecting the canister and mouthpiece. When needed in an emergency, the miner removes the outer protective cover and dons the unit. For both devices oxygen is immediately available once the mouthpiece is placed in the mouth. These two new units have received prototype approval from the National Institute for Occupation and Safety Health (NIOSH) and the Mining Enforcement and Safety Administration (MESA).

Jan 1, 1976

By C. M. Frost

Crude shale oil produced by gas combustion retorting of Green River oil shale was hydrocracked over a cobalt molybdate catalyst at operating pressures of 500, 1,000, 1,500, and 3,000 psig, an operating temperature of 8900 F, and a liquid hourly space velocity of 1.0. Hydrogen feed rate was maintained at 6,000 scf/bbl. The volume-percent yields of total liquid product were directly proportional to the operating pressure. Weight-percent conversion and volume-percent yields of gasoline were directly proportional to the log of the operating pressure. Catalyst deposit percentages were inversely proportional to the log of the operating pressure. Nitrogen and sulfur removal rates as well as saturation of the liquid products increased as the operating pressure was increased.

Jan 1, 1973

By Irving Hartmann

At the 9th International Conference of Directors of Safety in Mines Research a paper6/ was presented describing the initial phases of research by the Safety in Mines Research Establishment at Buxton, England, on the remote control of timber fires with high-expansion foam plugs in a rock tunnel. The work received extensive publicity, and great interest was aroused by the implied possibility that the method might be used successfully to control coal-mine fires, which for various reasons cannot be approached and attacked by standard fire fighting measures and frequently require sealing extensive, valuable coal properties and lead to loss of production and coal reserves and occasionally loss of lives. To investigate the practicability of the foam-plug technique under American min¬ing conditions, with room-and-pillar-type extraction and multiple entries, the Bureau of Mines in 1957 began an investigation at its Experimental Coal Mine, Bruceton, Pa, In preparation for this work it was necessary to rehabilitate and reinforce an elliptical tunnel in the mine where studies had been made, many years ago, leading to development of a ventilation system used in the Holland Tunnels between New York and New Jersey, and in many other vehicular tunnels.

Jan 1, 1958

By J. W. Horne

The United States Bureau of Mines in cooperation with the State of Colorado at the University of Colorado has conducted experiments to determine the amount and composition of the noncondensable cases evolved when crude shale oil is distilled under pressure. Hydrogen sulphide is one of the components found in the complex mixture of uses produced by the distillation of shale oil under pressure. This paper deals with the apparatus and method used in determining the amount of hydrogen sulphide evolved in the laboratory experimental cracking stills.

Jan 1, 1931

By A. L. Engel

Many western ores containing ;old, silver, and copper can be mined and concentrated at a profit only when the recovery of those metals is high and treatment costs are low. Usually, ores containing easily dissolved copper minerals, or copper minerals that become soluble to some extent through oxidation during treatment, present a real problem in cyanidation. Copper cyanide compounds are formed that tend to 'precipitate and that cannot yield regenerated cyanide and metallic copper on contact with zinc. This results not only in some loss of copper through solution in cyanide, but in excessive consumption of cyanide above the amount required for the extraction of Gold and silver. Any moans, therefore, of minimizing the: loss of cyanide while at the same time effecting high recoveries of the several values contained in the ore is of wide interest. A sample of typical low-grade ore of gold, silver, and copper, containing copper-sulfide minerals, was obtained from the MacLaren Gold Mines Co., Cooke, Park County, Mont., for laboratory investigation by flotation and cyanidation.

Jan 1, 1950

By H. Herbert Hughes

Iceland spar is a variety of calcite ( calcium carbonate ) characterized by its purity , transparency , and perfection of crystalline structure . It takes its name from the country in which it was discovered . The actual demand for it is small , but the supplies of high - grade optical spar are so meager that the search for it has become international in its scope . Iceland spar is a scientific necessity , for without it research precision and technology would be hampered considerably . The earliest students of mineralogy were familiar with calcite , but the transparent variety was not discovered until early in the seventeenth century , when crystals of it were found in the bed of a stream in Iceland . It received little attention until 1669 , when Erasmus Bartholinus first recognized its powers of double refraction . The results of his investigation were published in a book , " Experimenta Crystalli Islandici , " which appeared in 1670. The law governing the action of the rerracted rays was discovered by Christian Huygens eight years later . The polarization of light rays in passing through Iceland spar was discovered in 1809 by Etienne Louis Malus , a French physicist , who published a paper describing the phenomenon . His work was closely followed by that of William Nicol , who in 1828 designed the Nicol prism which is still used as the source of polarized light in most optical instruments .

Jul 1, 1931

By William C. McBee

Prompted by forecasts of a sulfur oversupply, the Bureau of Mines, U.S. Department of the Interior, is conducting research on potentially large-scale uses of this commodity to extend or replace such construction materials as asphalt, cement, and mineral aggregates. Through these efforts, paving materials have been developed in which sulfur replaces up to 50 pct of the asphalt normally present and which can be prepared and placed with existing mixing and paving equipment. Laboratory properties and design methods for this direct mixing process are described along with properties obtained on small-and large-scale field demonstration projects. These properties are compared with those obtained from control materials prepared without sulfur additions. Monitoring for toxic gases during laboratory and commercial mixing and paving operations is discussed also.

Jan 1, 1978

By W. M. Weigel

"Sand is one of the most useful and, fortunately, one of the most common mineral commodities. By far the largest proportion of the production is used in construction, including all forms of building, concrete and paving, sand for this purpose is produced in every State in appreciable amounts. Excluding send used for railroad ballast, molding sand stands not in tonnage produced, followed by glass sand.Special sands. In addition to the above, many grades of sands, with special characteristics, are used in industrial processes, and may be classed in a group as ""special sends"". This includes filter sand, sand blast sand, engine sand, abrasive send, fire or furnace send, special flooring sand, roofing sand used as a finish for prepared roofings and pottery placing sand sand blast and filter sand have been discussed in previous reports.Very few send companies depend upon the production of any one of these grades, as their source of revenue. They are generally especially prepared from the bank run of sand by different methods of screening or washing, or may, in some instances, be by-products from the production of ether grades. Many companies not now producing them might be able to supply local demands by a slight addition to their plant. In nearly all cases, they command a better price than the usual grades of building sand.Definitions and Properties.Engine sand, or traction sand, as it is sometimes called, is used to prevent the slipping of the driving wheels of locomotives, or other self-propelled vehicles, on wet or slippery rails. Its greatest use is, of course, for railroad locomotives, but street cars use considerable amounts and mine locomotives require its use. As the send must be very dry when used, most consumers have their can drying equipment, so it is often shipped damp, with its natural water content on what resulting from washing by the producer."

Oct 1, 1924

By R. R. Sayers

Mine operators and managers for a number of years have known that the maintenance of health among the workers has an appreciable financial value, In order to maintain the health, it has been found ne cessery to imow; 1. The health hazards existing in the industry as a whole and the specific hazard in the individual mine. 2. The physical condition of applicants for employment as well as that of the old employees. This can be determined only by systematic physical examination of all applicants and of regular employees at intervals of at least once a year thereafter. 3. All cases of sickness that occur among the workers. No operator or manager, or personnel, medical, or safety organization can control or prevent sickness without knowing where, when, and under what conditions the sickness actually occurs. In order to obtain information as to the hazards of industry, investigations have been and are being made of the effects of the condi- tions both in the field under usual working practices and in the laboratory. In the field several factors are generally present which affect the health. The effect of these factors may be determined by studying each of them separately in the laboratory. However, both the field and the laboratory studies are limited in value in that such studies usually have been made over a comparatively short period. While we have some information as to their immediate effect, we do not know to what extent extreme heat, humidity, the presence of dust or other health hazards are the cause of disability. Mortality statistics are probably the most easily available indices as to the hazards of industry. As an example, a study of such statistics among coal miners of Indiana shows a marked increase in the death rate in 1918.

Mar 1, 1923

By George C. Price

The Bureau of Mines conducted this study in the Roslyn No.5 coalbed in the State of Washington to determine the feasibility of mining hydraulically the portion of the coalbed that was steeply pitching. All of the experimental mining was done while advancing raises and rooms. A Bureau-developed hydraulic mining machine was used successfully in the pitching coalbed. It consisted of a remotely controlled monitor mounted on a self-advancing roof support unit of the type commonly used for roof support in longwall mining systems. The coal cutting rates averaged 0.73 and 0.54 ton per minute in raise and room mining, respectively, while using water volumes up to 230 gpm at a pressure of 4,000 psig. Productivity averaged 4.7 and 5.2 tons per man-shift for raise and room mining, respectively, compared with 7.5 and 8.5 tons per man-shift, respectively, by conventional hand mining methods.

Jan 1, 1965

By Robert S. Sanford

"INTRODUCTION AND SUMMARYThis paper is one of a series recently undertaken by the Mining Branch, Bureau of Mines, College Park, Md., to describe current practice in hauling ore and waste by truck at various mines.Heavy-duty ore trucks are replacing railroads at many large open-cut mines and even at a few underground mines. Recently a few mines have been equipped with trucks for transporting ore to a central point, from which conveyor belts move the ore out of the mine. This paper deals only with truck haulage methods and costs.The requirements for efficient low-cost truck haulage are good trucks designed for heavy loads, adequate truck maintenance, smooth roads, and well-trained truck drivers.A correct balance must be maintained between the primary crusher capacity, the number of shovels loading ore, and the number of trucks hauling ore.The cost of tires is important. Tire companies are manufacturing better tires. Mining companies are prolonging the life of tires by building better roads and maintaining correct tire pressure.The trend is toward heavier equipment. In 1949 it cost $0.0925 a long ton to haul ore and waste with a 15-ton truck and $0.0743 a long ton with a 22-ton truck.When trucks are properly maintained, hauling costs do not increase with the age of the trucks. During 1948 it cost $0.1118 per long ton to haul with the four oldest 15-ton trucks and $0.1130 per long ton to haul with the four newest 15-ton trucks, two of which were purchased in 1945 and two in 1947.The weighted ayerage cost of hauling a long ton of ore to the crusher and waste to the dump has been reduced from $0.1159 in 1948 to $0.087 in 1949."

Oct 1, 1950

By J. B. Janus

This report continues a series of analyses of coal samples made by the Bureau of Mines in connection with the yearly purchase of several million tons of coal for various Government agencies. Listed are the analytical data on the composition and quality of tipple and de livered samples of coal collected during fiscal year 1974.

Jan 1, 1975

By J. B. Janus

This report, the 25th in a series, lists analytical data of coal samples collected by the Bureau of Mines in connection with the purchase of several million tons of coal for various Government agencies during fiscal year 1975. Tipple samples were collected by Bureau of Mines engineers at tipples as coal was being loaded into railroad cars or trucks. Ultimate analyses are given for these coalbeds only. The delivered coal was sampled at destination in accordance with instructions furnished by the Bureau of Mines, and all samples were analyzed in the Bureau laboratory at Pittsburgh.

Jan 1, 1976

By R. H. Lien

The Bureau of Mines, U.S. Department of the Interior, has developed a flue gas desulfurization process as part of its goal of minimizing the undesirable environmental impacts associated with energy and mineral-processing plants. This process, known as the citrate process, involves absorption of sulfur dioxide (SO2) in a buffered solution of citric acid. The S02-loaded solution is regenerated by reaction of the S02 with hydrogen sulfide (H2S) to form elemental sulfur. As an adjunct to the citrate process, bench-scale research has shown that S02-loaded citrate or glycolate solutions can be regenerated by countercurrent contact with steam (stripping) in packed towers. Concentrated S02 is produced by condensing the steam from the stripper product. Thus, steam stripping provides strong S02 gas for liquefaction, sulfuric acid production, or reduction to elemental sulfur. Stripping steam requirements were determined for treatment of 0.25-, 0.50-3 1.0-, and 2.0-pct-S02 waste gases. Steam requirements decreased with increasing S02 concentration n the simulated waste gases. For example, 5 grams of steam per gram o S02 was required to remove 90 pct of the S02 from a simulated copper smelter gas (2.0 pct S02), while 30 grams of steam per gram of S02 was needed for 90 pct S02 removal from a simulated coal-fired powerplant gas (0.25 pct S02).

Jan 1, 1979

By J. W. Horne

The United States Bureau of Mines in cooperation with the State of Colorado at the University of Colorado has conducted experiments to determine the amount and composition of the non-condensable gases evolved when crude shale oil is distilled under pressure. Hydrogen sulphide is one of the components found in the complex mixture of Gases produced by the distillation of shale oil under pressure. This paper deals with the apparatus and method used in determining the amount of hydrogen sulphide evolved in the laboratory experimental cracking stills. The study required a complete extraction of all the hydrogen sulphide from the gas stream after it left the water-cooled distillate condensers and before the gas stream entered the charcoal absorber for removing the light naphtha. In devising the method it was necessary to take into account a constant variation of velocity, pressure, and percentage of sulphide in the total gas stream coming from the still. Ordinarily, the quantitative determination of hydrogen sulphide in gas is made by analyzing small samples taken at regular intervals. This estimation can be accomplished by use of the Bunts gas burette as modified by Tutriler, or by a similar method. In the industries where the flow of gas is constant and of uniform composition, this practice is sufficiently accurate for plant control. For experimental work where many variables have to be taken into consideration, as in the case at band; these methods are not applicable.

Jan 1, 1931