Search Documents

By J. W. Town

As part of the Federal Bureau of Mines titanium resources examination program, samples from seven deposits in the Pacific Northwest were tested for amenability to various beneficiation techniques. The samples obtained by the Bureau's Office of Mineral Resources at Spokane, Washington represent a large potential source of titanium. This report summarizes the results of tests at the Bureau's Metallurgy Research Center, Albany, Oregon. Recoveries from tabling placer samples were about 50 percent at grades of 30 percent titanium dioxide. Flotation was the most effective method for concentrating the fine ilmenite in clay samples; recoveries of approximately 50 30 percent titanium dioxide. Flotation was the most effective method for concentrating the fine ilmenite in clay samples; recoveries of approximately 50

Jan 1, 1961

By S. P. Polack

"INTRODUCTION The purpose of this circular is to correlate the information obtained during personal investigations at the sites of four rock tunnels in the process of construction and information obtained from the records and personal views of the constructors of two other tunnels that were not visited during the, excavation phase of construction and to present this information for the benefit of those who contemplate future construction of rock tunnels.Modern mechanized coal mining requires better, safer, properly alined haulageways and beltways; consequently, better understanding of tunneling methods by coal-mining men will be necessary. The possibility of future high-speed haulage systems utilizing rock tunnels in the more solid rock strata above or below the coal beds must not be discounted. In the past, tunnels have been driven for use in draining and unwatering inundated coal mines. At present, the need for such tunnels is very evident in some parts of the coal-mining regions, notably in the Pennsylvania anthracite fields, and studies along these lines are in progress. The average coal-mining man has little time or opportunity to visit tunnels while they are being exca-vated; therefore, it is hoped that this information will assist him in constructing tunnels safely if he is required to do so in the future.The tunnels described herein differ in size, shape, usage, and, in many instances, in their geological aspects. Full-face, heading and bench, and pilot-tunnel, and enlargement methods of excavation were utilized.The roof-support methods show diverse designs and materials of construction to suit each purpose and condition. The superiority of steel roof support over wood is demonstrated beyond doubt and is shown clearly in the photographs included in this circular.The illustrations (photographs taken by the U. S. Bureau of Mines, the U. S. Corps of Engineers, and others) show many of the necessary steps taken during the excavation and the erection of roof support in tunnels under construction."

May 1, 1950

By A. Gene Collins

This report discusses some of the chemistry and geochemistry of cesium and rubidium. Knowledge of the cesium and rubidium content of oilfield waters aids in resolving the origin of waters and petroleum, exploring for petroleum and other valuable minerals, discovering water pollution sources, and augmenting the knowledge of geologic formations. The methods described in this report permit the detection of less than 0.01 mg/l of cesium and/or rubidium in a complex oilfield brine or water. Solvents possessing high-dielectric constants were evaluated for their ability to extract cesium and rubidium tetraphenylboron from oilfield waters and for their flame emission characteristics. Nitroethane was selected and used for the extraction and flame spectrophotometric determinations because it gave the highest sensitivity. Cesium 137 and rubidium 86 were used to determine the extraction efficiencies, which were about 87 percent and 58 percent respectively using a single 10 ml nitroethane extraction from a distilled water matrix. The standard deviation of the determination was 0.0008 mg for cesium and 0.0007 mg for rubidium in the 0.01 mg range.

Jan 1, 1965

By L. L. Brown

As part of the Federal effort to help maintain an adequate supply of fertilizer materials, the Bureau of Mines conducted research to characterize complex low-grade Michigan phosphate materials and to devise methods for recovering fertilizer-grade phosphate concentrates. The rock is from middle Precambrian sedimentary formations in the Marquette Range located in the central part of the Upper Peninsula of Michigan. Occurrence of phosphate-bearing sediments in Precambrian rocks is rare. This deposit, containing 12 to 15 pct P205, is believed to be the richest Precambrian phosphate deposit in the United States. Petrographic examination showed that the conglomeritic rock contains crystalline apatite both in "black pebbles" and in quartz matrix. Attrition scrubbing and sizing tests showed that there is no tendency for phosphate to concentrate in any of the sized fractions. In beneficiation tests, which included grinding to minus 325 mesh followed by phosphate mineral flotation using a fatty acid-fuel oil collector, a phosphate concentrate was obtained that had a grade of 30 pct P205 and a P205 recovery of 72 pct. This concentrate should be suitable for fertilizer manufacture.

Jan 1, 1981

By A. Landsberg

Chlorination of sulfide minerals and several prepared metal sulfides was studied. The resulting data were analyzed with respect to kinetics of the reactions and application to nonpolluting methods of winning metals from sulfide ores. Sulfides of iron, copper-iron, nickel, lead, zinc, silver, bismuth, arsenic, rhenium, molybdenum, and tungsten were investigated at temperatures up to 600° C. Copper-iron, lead, and zinc sulfides showed at least some product-controlled (parabolic) kinetics at the lower temperatures within the temperature ranges studied, but only nickel and silver sulfides had chlorination rates controlled by parabolic reaction kinetics in the commercially important temperature range of 450° to 600° C.

Jan 1, 1975

By L. H. Adami

The heats of formation of anhydrous cadmium sulfate, cobalt sulfate, copper sulfate, nickel sulfate, and zinc sulfate were determined by hydrochloric acid solution calorimetry. The values at 298.15° K for formation from the metal, rhombic sulfur, and oxygen gas follow (cal/mole): CdS04J -222.0 ± 0.3; CoS04, -212.0 ± 0.4; CuS04) -183.4 ± 0.6; NiS04, -208.1 ± 0.2; and ZnS04, -233.1 ± 0.2. Corresponding heats of decomposition to form the metal oxide, sulfur dioxide, and oxygen were derived from these results; heats of decomposition to form the metal oxide and sulfur trioxide were also derived.

Jan 1, 1965

By W. J. Fene, G. W. Grove

An important activity of the Safety Division of the Bureau of Mines , in its efforts to reduce accidents , is the safety inspection of mines . Inspections are made at the request of the operators and are not connected with the inspections by the various State departments of mines . The operating management is furnished with a confidential report of the results of the Bureau's inspections , with recommendations for elimination of the hazards found . These mine - safety inspections include a study of mining practices , conditions , and equipment and in some cases the sampling and analysis of mine air and coal dust . The Bureau of Mines has no regulatory powers , therefore the recommendations made in these reports are merely suggestions , and operators are not required to adopt them . Mine inspections are a check on safety standards , methods , and practices and are essential to any accident -prevention program . A foreman or superintendent may be sincere in his efforts to operate a mine safely and believe that he has done everything possible to attain this end . However , experience has shown that because of his familiarity with the mine and the consequent " nearness " of its various features many unsafe conditions may be , and in most cases are , overlooked ; an inspector , particularly an outsider who is trained to look for hazards , can point out the unsafe conditions overlooked by the foreman or superintendent . Some companies employ safety engineers who make regular inspections of their mines , report substandard conditions and hazards found , and make recommendations for correcting them . Unless these recommendations are carried out the inspections have little value . In making recommendations , due consideration should be given to the feasibility of carrying them out ; the management may and very often does consider a recommendation impracticable because of the

Mar 1, 1935

By I. L. Nichols, K. C. Dean, P. H. Johnson

Hydrochloric acid , sulfuric acid , and chloridizing roast- water leaching methods for dissolution of cesium and rubidium from Maine , Canada , and Southern Rhodesia pollucite ores and their flotation products were investigated by small- scale tests . Optimum conditions were determined to be ( 1 ) for hydrochloric acid leaching , use 12.7 equivalents of 8.8 normal acid per equivalent of cesium in the sample and leach for 6 hours at 100 ° C ; ( 2 ) for sulfuric acid leaching , use 12.7 equivalents of 14.4 normal acid and leach for 2 hours at 120° C ; and (3 ) for chloridizing roast - water leaching , roast minus 200 - mesh ore, limestone , and calcium chloride in a ratio of 2 : 4 : 1 , respectively , for 1 hour at 900 ° C , and leach the calcine for 1 hour at 80 ° C with enough water to give 35 pct solids . Extractions of cesium from ores and flotation products containing over 20 pct cesium were in excess of 97 , 93 , and 96 pct for the hydrochloric acid , sulfuric acid , and chloridizing roast - water leach processes , respectively .

Jan 1, 1964

By M. J. Ferrante

Low-temperature heat capacities and high-temperature enthalpies for syn¬thetic Cu2S and CuS were measured. This investigation is part of the Bureau of Mines goals to provide thermodynamic data essential to the more efficient processing of copper ores, and thereby minimize the current dislocations in energy, environment, and mineral supply. Heat capacities were measured with an adiabatic calorimeter from 5 to 310 K, and resulted in S°298 = 27.76 for Cu2S(c) and S°298 = 16.05 cal/deg mole for CuS(c). Low-temperature values are tabulated for Cp°, S°, -(G°-Ho°)/T, and H°-Ho°. Enthalpies were measured with a copper block calorimeter from 298.15 to 1,600 K for Cu2S(c,1) and 298.15 to 780 K for CuS(c). The thermal behavior of CuS showed no transitions or other significant anomalies for the low- or high-temperature investigations. Cu2S showed reversible transitions at 376 K with an isothermal heat absorption of 0.865 kcal/mole, 720 K with an isothermal absorption of 0.280 kcal/mole, and approximately 1,400 K (congruent melting point) with a heat of fusion of 3.070 kcal/mole. High-temperature data are tabulated for H°-H°298, Cp°, S°, and -(G°-H°298)/T. Enthalpies are also expressed in equation form. The low¬and high-temperature data were combined with data from the literature to cal¬culate and tabulate ?Hf°, ?Gf°, and log Kf as a function of temperature.

Jan 1, 1978

By Elizabeth A. Johnson

The vaporization thermodynamics of the aluminum-silicon carbides Al4SiC4 and Al8SiC7 were studied by the Bureau of Mines over the temperature range of approximately 1,500 to 1,700 K. Vapor pressures were measured by a Knudsen effusion-mass spectrometry technique in which powdered samples were effused from graphite crucibles through small orifices. For each compound, a total of six orifice diameters was tested to verify equilibrium within the cell. Aluminum, mass number 27, was the only vapor species detected over the range 4 to 200 amu. Experimental results are based on the following equations for incongruent decomposition: A14SiC4(cr) - 4A1(g) + SiC(a,hex) + 3C(gr); Al8SiC7(cr) - 8A1(g) + SiC(a,hex) + 6C(gr). The observed vapor pressure-temperature relationships determined with a cell orifice area of 2.0 x 10-3 cm2 for Al4SiC4 and 1.81 x 10-3 cm2 for A18SiC7 are the following: Log P - (-18,682/T) + 12.476, for Al4SiC4 (1,550 to 1,643 K) and Log P = (-19,308/T) + 12.421, for Al8SiC7 (1,526 to 1,784 K), with P in pascals and T in kelvins. Third-law analysis of the data provided the following heats of formation: A14SiC4 ?H at 298.15 K - -50.0 kcal/mol and A18SiC7 ?H at 298.15 K - -92.1 kcal/mol.

Jan 1, 2011

By Joan C. Biordi

In this research by the Bureau of Mines, slightly lean CH4-O2-Ar flames at 0.042 atm with and without small amounts of the inhibitor CF3Br were probed using molecular beam and mass spectrometric techniques. Ratios of product concentrations to reactant concentrations were formed and compared with the equilibrium constant for seven reactions--(l) H+O2 = OH+O, (2) O+H2 = OH+H, (3) OH+H2 = H2O+H, (4) OH+OH = H2O+O, (5) CO+OH = CO2+H, (6) Br+HBr = Br2+H, and (7) H+HBr =H2+Br--to determine to what extent they may be considered balanced in various regions of the flame. With the possible exception of reaction 4, none of the reactions are completely balanced until maximum flame temperature is reached. Once the reactions become equilibrated, their balance is maintained as the temperature and radical concentrations falloff in the secondary reaction zone. Reaction 7, in inhibited flames, is balanced at relatively low temperatures, comparable to reaction 4. Reaction 6 was found not to balance in either the secondary or primary reaction zones. Radical decay in the secondary reaction zone was analyzed using the pool-decay concept. The important recombination reactions were judged to be H+OH+M~H2O+M, and H+O2+M?HO2+M. A rate coefficient of 2x1016 cm6 mole-2 sec-1 is calculated for M = the burnt gas mixture of Ar, HaO, CO2, and 5x1015 cm6 mole-a sec-1 is calculated for M = Ar (both for T = 1,750±150 K).

Jan 1, 1977

By Martin J. Gavin

The oil- shale studies of the Bureau of Mines , conducted in cooperation with the State of Colorado and the University of Utah , have for their primary purpose the determination of retorting and refining conditions most favorable for obtaining the highest yields of most satisfactory products . Oil shales , typical of the deposits in several States , are retorted in carefully controlled retorts of differe types , the conditions being varied in successive runs as the results indicate that improvement in the yield and quality of the products most desired may be expected . Each shale presents a somewhat different problem , for it has been found that different shales treated under similar conditions yield products of different natures , and also that the same shale will yield products of different natures when retorted under different conditions . Some shales apparently can not be made to yield , under any set of conditions , products of so high an order as are yielded by other shales . This indicates that the oil -yielding materials of certain shales differ in constitution and in their manner of breaking down when undergoing destructive distillation . Other shales appear to contain oil - yielding materials that resemble each other closely as regards chemical constitution , yet they require some. what different conditions of treatment , if products of similar nature are to be produced from each . In such cases the controlling factors seem to be the richness of the shale that is , its content of oil -yielding material and the physical and chemical nature of its mineral parts .

Mar 1, 1922

By Gary P. Sames

This report discusses some practical applications of a geotechnical investigation conducted by the U.S. Bureau of Mines that can help mine operators meet revised Federal regulations in their roof control plans. The investigation, designed to characterize roof conditions near the coalbed outcrop in drift coal mines in eastern Kentucky, revealed that weathered stress-relief joints near outcrop are crucial ground control factors in the region. The joints' origin and character were determined through underground mapping of many joints in coal mine roof and detailed observations and measurement of joint trends and physical characteristics in widely separated strip mine highwalls and roadcuts. This resulted in an understanding of stress-relief-joint patterns and the effect of various rock types on the intensity of weathering in the joints. That information is used in this report to show how stress-relief joints contribute to roof failure and how, through improved roof support and mine planning, safer roof support plans can be developed.

Jan 1, 1992

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Ti and Zn-1.0 wt pct Cu-Ti alloys containing up to 0.36 wt pct Ti. Finish rolling was at varied temperatures to total reductions as high as 92 pct. Alloy properties are very sensitive to various combinations of composition, rolling temperature, and reduction. Properly rolled Zn-1.0 Cu-Ti alloys are superior in strength to Zn-Ti alloys. Conditions are described that lead to best tensile properties. Creep resistance for Zn-Ti alloys decreases with increased rolling temperature when finish rolled to 92-pct total reduction: but not when finish rolled to 33- or 67-pct reduction. Creep resistance for 7n-1.0 Cu-Ti alloys improves with increased rolling temperature to about 480° F. Heavily cold-rolled Zn-1.0 Cu-Ti alloys have fine grain sizes and poor hardness, tensile, and creep properties, but high ductility. Thermal expansivity is markedly affected by the copper addition. Data show the anisotropy of tensile, creep, and thermal expansivity properties. Large idiomorphic crystallites of TiZn15 appear in both Zn-Ti and Zn-Cu-Ti alloys when more than about 0.2 pct Ti is present. A new Zn-Cu-Ti intermediate phase was also identified. Empirical equations are presented relating creep rates with major process variables.

Jan 1, 1971

By Jonnie M. Estes

A two-constant equation is presented for helium from 30° = T = 1,473° K. This equation is developed by modifying a generalized equation of state originally presented by Redlich and Kwong (20).3 The modification consists of setting B = 0.06372 Tc/PeT. This modified equation represents the compressibility factors of each of 80 isotherms tested in this temperature range to less than 1 percent average deviation.

Jan 1, 1967

By G. S. Scott, L. D. Schmidt, J. A. KELLEY, E. L. FISH

One of the war problems with which the Bureau of Mines is concerned is to increase production of iron and steel , in which coke is one of the major factors . The output of byproduct coke for use in iron blast furnaces is insufficient and is being supplemented by coke from beehive ovens (figs . 1 , 2 , and 3) . Some difficulties that cause a reduction in iron output have been reported in the use of some of the beehive coke.6/ About 20 years have elapsed since beehive coke was made on a large scale , and many of the skilled operators of those days are no longer available . Furthermore , in many instances the quality of the coal supplied to the ovens has not been as good as formerly. The ash and sulfur contents are often abnormally high; and in other instances they vary greatly in amount, so that a nonuniform coke is produced . To assist operators to improve quality and yield of beehive coke , the Bureau of Mines equipped a truck as a field laboratory ( fig . 4 ) and sent the authors with it into the Pennsylvania beehive district . The truck contains necessary equipment for sampling and analyzing coke oven gases , measuring temperatures , screen - sizing coal, and float -and - sink testing coal . Coal specimens may be sent to the Pittsburgh laboratory for analysis . Beehive plants producing good coke were visited first to observe details of operation and to collect data on the operating process . These covered temperatures , analyses of the exit ( or trunnel) gases , and coal quality, and were to be utilized in searching for faults in plants not producing good - quality coke and to assist in improving such plants or their operation .

Dec 1, 1943

By D. S. Kimmel

The Bureau of Mines sponsored development of a system to remotely energize and de-energize the trolley wire in a section in response to demands from vehicles as they enter and leave the controlled section. The system developed utilizes a detector/actuator that controls a dc contactor at the outby end, and a 3 kHz oscillator at the inby end. A prototype system has been built and installed at the Bureau's trolley test site at Bruceton, Pennsylvania which has demonstrated the ability to also provide load discrimination for faults of 300 amperes or more. The system could readily be modified by locating the oscillator on the vehicle to provide automatic de-energizing of the trolley wire when the vehicle's pole is removed or the vehicle leaves the section.

Jan 1, 1978

By J. E. Gebhardt

External control of the electrochemical potential of a bed of mineral particles has been investigated by the Bureau of Mines as a method for controlling particle inter-action with organic collectors and thus, flotation response. A cylindrically shaped, 200-to 300-g bed of sulfide mineral particles was used as the working electrode to examine the potential distribution in the bed. The dissolved oxygen concentration of the electrolyte had a significant effect on the potential profile across the mineral bed. Low oxygen levels were necessary to achieve uniform electrochemical potential distributions. Flotation separation of a chalcocite-pyrite mineral mixture by controlled potential was achieved using ethylxanthate, but the flotation behavior of chalcocite and pyrite from the mixture does not follow the flotation behavior of the individual minerals. That is, the presence of another sulfide mineral alters the flotation behavior with ethylxan-thate. Galvanic interaction due to mineral-to-mineral contact between chalcocite and pyrite contributes to differences in the recovery. Chalcocite dissolution products had a deleterious effect on pyrite flotation by activating flotation below -0.1 V (saturated calomel electrode) and depressing flotation above -0.1 V. Pyrite dissolution products had no effect on chalcocite flotation.

Jan 1, 1985

By D. H. Carlson

The U.S. Bureau of Mines and Michigan Technological University (MTU) are collaborating to develop an apparatus for measuring diesel tailpipe emissions in underground mines. A tailpipe emissions measurement apparatus (EMA) is described that dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, CO2, NO, and NO2 at known dilution ratios. The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory-grade instruments. Concentrations of CO and CO2 measured by the EMA were usually within ± 14 pct of concentrations measured by laboratory-grade instruments for CO and ±20 pct for CO2. EMA¬ measured DPM concentrations were, on average, 29 pct lower than those measured by laboratory-grade instruments, with the differences being fairly consistent. The CO and CO2 differences are related to the method of calculating the EMA's dilution ratio, and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminary analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios.

Jan 1, 2010

By Thomas L. Chapman

The San Manuel is a deposit of low-grade disseminated copper ore. It was brought to the attention of the government in October 1942 through an application to the Reconstruction Finance Corporation for a development loan, supported by a report by Henry W. Nichols. Nichols' sampling of two outcrops containing copper silicate and his geologic map indicated that a minable body of copper ore might be developed. The Federal Geological Survey was requested to examine the property. The Survey mapped the geology in March 1943 and cut a few check samples, which substantially confirmed Nichols' sampling of the outcrops and a few shallow workings. The geologists of the Survey recommended some test drilling by the Bureau of Mines. The property was examined by the author and Wm. D. Hughes, associate engineer of the Bureau of Mines on March 22 and 26, 1943, and a preliminary drilling campaign was recommended. Five shallow churn-drill holes totaling 1,480 feet were put down under the supervision of Chas. A. Kumke, one of the Bureau's engineers, from November 23, 1943, to January 13, 1944. This work indicated that the deposit extended deeper than the 350-foot depth attained in the deepest hole and might have very considerable areal extent. Additional funds were allotted, and the drilling contract was extended twice to a final maximum of 17,000 feet with 2,000 feet maximum depth of hole. Drilling was continued by the Bureau of Mines until February 2, 1945, when 15,844 feet of hole had been drilled. The Magna Copper Co. took options on this and adjoining property in September 1944 and commenced drilling with two machines. It also engaged the two contract drills used by the Bureau after it stopped drilling. It exercised its options in August 1945 and organized the San Manuel Copper Corp. to operate the property. That company is continuing to explore the ore body with six churn drills. Thomas Lyon took options early in 1945 on holdings adjoining the San Manuel property on the east and is operating two churn drills. Exploration up to the completion of the last holes started by the Bureau of Mines indicated a block of ore 3,100 feet long, 400 to 800 feet wide, and 500 to 900 feet thick, and averaging about 0.8 percent copper. Subsequent drilling showed that the ore body extends considerably beyond this block. The axis of the ore body strikes about N. 61° E. Copper minerals are disseminated in hydrothermally altered quartz monzonite and monzonite porphyry. Ore outcrops in two small areas over the northeast part of the block. Elsewhere the copper-bearing rocks are capped by Gila conglomerate, which thickens toward the west and south. Drilling showed that the ore is in a thick, tabular body with a steep dip to the south. The ore body lies near the surface in the northeastern part of the block. The south side of the block is much farther below the surface than the north side. There the upper part of the copper-bearing rocks is lightly mineralized, so that the hanging wall of minable ore lies deeper than the base of the conglomerate cap, which thickens southward.

Aug 1, 1947