Search Documents

By L. J. Froisland

The U.S. Bureau of Mines conducted laboratory studies on sulfuric acid (H2S04) digestion of alunite [KA13(S04)2(OH)6] as a means for treating domestic deposits of this mineral. Digesting alunite ore in boiling H2S04 at concentrations of 88-wt-pct acid or higher breaks down the alunite and permits a convenient separation of potassium and aluminum. The digestion reaction is a complex sulfation reaction occurring in two stages. In this reaction, the potassium component extracts into the H2S04 for eventual recovery as potassium sulfate k2s04 in a separate unit operation. Aluminum is left as acid-insoluble aluminum sulfate [A12(S04)a], which can be extracted by a 95° C water leach. Additional purification of AI2(S04)a produced in this study is needed to meet cell-grade alumina (Al202) purity specifications. Extraction and separation of potassium and aluminum from the alunite ore were consistently above 90 pct.

Jan 1, 1989

By E. P. Youngman

This paper is one of a series of digests of foreign minim legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the minim lams of Ceylon has been prey tired from the best available information in Washington and is released subject to amplification and correction, if necessary, by United States foreign-service officers. INTRODUCTION Ceylon has no basic mining law; the general rules governing the granting of mineral concessions and affecting legal titles of concessionaires are laid down in Ceylon Government ordinances or are found in the authorized forms for licenses and leases. The material available in the preparation of this digest is as follows:

Jan 1, 1933

By D. Montagna

The Kroll-Betterton process for debismuthizing lead is based on adding calcium and magnesium to impure molten bullion to form solid Ca-Mg-Bi inter-metallic compounds that float on the surface as drosses. Present practice in industry is to hand-skim off these drosses, often followed by hydraulic pressing to squeeze out some of the entrapped liquid lead. In an effort to develop an improved technique, the use of an argon-shrouded dipping centrifuge to perform the required phase separation was investigated. Centrifugation experiments demonstrated that the bismuth content of an impure bullion could be lowered from an initial 0.5 percent down to 0.03 percent with a lead recovery of 90 percent, which is comparable to lead recovery after hand skimming of drosses in commercial lead-debismuthizing operations. Centrifugation provides better control in removing drosses, faster operation with less oxidation and relatively little fuming, and recovery of a lead bullion that approaches commercial specifications.

Jan 1, 1972

By Edward D. Thimons

Inflatable stoppings are currently marketed for production use, and numerous mining companies have become interested in using such stoppings in rescue and recovery operations. The Bureau of Mines therefore evaluated the concept of using inflatable stoppings in emergency situations. The stoppings tested by the Bureau were 12-foot-diameter spheres inflated with a blower operated by a small battery pack. Experiments were conducted with the stoppings in a full-scale wooden mine model to evaluate their ability to withstand sliding or slipping at various internal and differential pressures, puncture resistance, various inflation techniques; and internal leakage from the stoppings. The stoppings were then installed and tested in the Bureau's Safety Research Coal Mine at Bruceton, Pa., to determine their effectiveness as mine air barriers. Despite some encouraging results obtained with the model and in-mine studies, the stoppings did not perform well in two operating metal mines where they proved difficult to erect and inadequate as air barriers.

Jan 1, 1976

By L. C. IlsLey

Investigations for safety of electrically operated mine equipment, safety lamps, and gas detectors are made at the Pittsburgh Experiment Station in accordance with published regulations termed "schedules." These schedules are revised from time to time, not only to keep in step with the progress of the industry, but also to permit much freedom of design as possible without lowering standards of safety. The following schedule covering electrical equipment, safety lamps, and gas detectors are now active: Schedule 2D. Explosion-Proof Mine Equipment. Requirements for Approval of of Storage-Battery Locomotives and Power Tucks, Junction Boxes, and Electric Motor-Driven Equipment.

Jan 1, 1939

By D. N. Nilsen

The Bureau of Mines is investigating a method to recover Ni, Cu, and Co from low-grade domestic laterites through reduction roasting, leaching, sol-vent extraction, and electrowinning unit operations. The objective of this research is to develop processing technology that can convert low-grade domestic deposits containing critical metals into national reserves. As a part of this research, a solvent extraction system was investigated for the extraction of nickel and copper, followed by the separation and production of suitable electrolytes. Nickel and copper were coextracted from ammoniacal ammonium sulfate leach liquors (pH~9.5) with LIX 64N extractant in a laboratory-size mixer-settler continuous circuit. Three extraction stages resulted in >99-pct extraction of nickel, substantial copper extraction, and essentially no cobalt extraction from leach liquors. A crowd stage reduced the ammonia loading on the solvent by maximizing nickel loading. Residual ammonia was removed from the loaded solvent with a pH-controlled scrub. Nickel and copper loaded on the solvent were separated by selective stripping. Typical nickel strip circuit operation using electrolyte containing 90 grams per liter (g/l) Ni and 11.9 g/l H2S04 yielded >99.9 pct Ni stripped from the solvent in five stages. The copper loading on the recycled solvent was controlled in a copper strip stage using electrolyte containing 25 g/l Cu and 160 g/l H2S04,

Jan 1, 1981

In 1991, the USBM (U. S. Bureau of Mines) evaluated the mineral resources of the 174,550-acre Bear Creek-Poker Peak area. Located 40 air miles east from Idaho Falls, ID, the study area is in the Caribou National Forest but is mostly administered by Targhee National Forest. USBM personnel mapped and sampled mines, prospects, and mineralized sites in and near the study area. Five types of mineral occurrences were identified in the study area: phosphate, limestone and travertine, placer gold, coal and uranium (the latter contained in the coal), and oil and gas. The study area has a high potential for oil and gas; evaluation of these commodities were beyond the scope of this study.

Jan 1, 1992

By R. Hogg, T. F. Dumm, L. G. Austin, M. Yekeler

"Dedicated to Professor Kurt Leschonski on the occasion of his 60th birthdayAbstractThe kinetics of batch grinding quartz from a feed of 600 by 425 Jim to a product of 80% less than 10 µm have been determined using screening and laser diffractometer sizing for size analysis. The specific rates of breakage decreased by a factor of about three when the material became less than about 100 µm in size, but the primary breakage distribution function also changed to give proponionately more fine material, so that the grinding efficiency expressed as the development of surface area (B.E:T.) per unit of energy input did not decrease. Analysis of the shape of the particles in the 2S x 38 µm size range showed that particles of this size produced by roll crushing or by 8 minutes of grinding of a 42S x 600 µm feed were not different but at long grinding times the particles were rounded. This suggests that the breakage mechanism changes to give more chipping and abrasion and less disintegrative fracture. As the material approached the ultrafine size range it adhered to the mill case and there was no further size reduction. However, a technique for striking the mill case to dislodge the particles was successful in allowing further grinding to 400Jo by weight less than 2 µm.1 IntroductionIt has long been known that it is difficult to accomplish ultrafme grinding in a tumbling ball mill. It has been reported [12, 13] that there is no further size reduction after some hours of grinding cement clinker in laboratory ball mills. Austin and Bagga (1] and Shah and Austin [16] have given an analysis of the kinetics of dry grinding in a laboratory ball mill, introducing the concept of a slowing-down factor K, which is the ratio of the specific rates of breakage at some long time of grinding to the normal specific rates of breakage. They showed that this factor decreased as fine material accumulated in the mill charge. Cottaar and co-workers [8-10] showed that the movement of solid in a dry laboratory ball mill was influenced by the fineness of the solid and by the presence of air, and that evacuation of air from the mill caused particle sedimentation and low rates of breakage.The concept of the slowing-down factor has also been used in wet grinding [17, 18]. At very .high slurry concentrations it appears to be correlated with a steady decrease of mill power caused by the build up of a layer of deposit sticking to the mill case. This reduces the effective mill diameter and, eventually, the balls start to adhere in the layer and centrifuge. A decrease of mill power always indicates less lifting and tumbling of the media and, hence, less breakage. However, slowing-down of breakage rates was also observed at lower slurry concentrations where there was no change in mill power."

Jan 1, 1990

By Mark R. Stephenson

Everyone knows that mining is a noisy job, but did you know that you are nine times more likely to lose your hearing than someone who works in a quieter job? If unprotected from noise on the job, by age 50, you will probably need hearing aids. Obviously, the best solution is to engineer out the noise, but that isn?t always im­mediately possible. Until mines are quieter, one way you can help save your vital sense of hearing is to use hearing protectors whenever the noise around you is hazardous. Even if you already have some hearing loss, you can use hearing protectors to prevent your hearing from getting worse. When loud noise is present, proper use of hearing protectors will help miners pre-vent most or all noise-induced hearing loss.

Jan 1, 1998

By N. S. Dalal, Xianglin Shi

"INTRODUCTIONEpidemiologic studies of workers in chromate-ore related industries, 1-3 and stainless steel welding and related occupations4 have shown that they have about 20-40 times higher risk of throat or respiratory track cancer than controls. Although the actual carcinogenic substances were not identified in these statistical studies, Cr(VI) compounds (for example, calcium chromate, zinc chromate, and lead chromate) were implicated as the causative agents, whereas Cr(III) compounds were not suspected as carcinogens. s These suggestions were supporte4 by laboratory studies wherein many Cr(VI) compounds produced sarcomas at the implant or injection sites.1,5 Squamous cell carcinomas and adenocarcinomas closely resembling human lung cancer were induced by intrabronchial implants of calcium chromate in rats, 6·7 whereas Cr(DI) oxide and Cr(lll) sulfate did not induce any tumor formation.6,7While the mechanism of the chromate-induced carcinogenicity is not fully understood, it is generally thought8 that it involves some damage to DNA. Specifically, it has been reported that: a) the chromate ion, henceforth referred to as chromate, can pass through the cell membrane and enter the cell while CR(DI) does not, 9 b) chromate does not interact with either native or denatured DNA 10 while Cr(III) does, 11 and c) the final Cr-DNA complex isolated from cellular reactions of chromate is Cr(III)-DNA, with Cr(III) binding to the phosphate groups.12,13 Thus the important question is: since Cr(DI) cannot pass through the membranes, how does Cr(III)-DNA complex form? For this to happen, Cr(VI) must be reduced to its lower oxidation states, 14 ultimately to Cr(III), by some reductants in the cellular environment. Unless this reduction occurs, the DNA would not be damaged and therefore no chromate carcinogenicity would ensue. Thus the reduction of chromate to its lower oxidation states seems to be a key step in the chromate carcinogenicity .1s One of the major reductants in cellular environments is thought to be glutathione (GSH), both outside and inside the cells.16-lB Some evidence for the role of GSH in the chromate toxicity was provided by recent studies showing that exposure of hamster cells to non-toxic levels of added selemite increases the levels of GSH as well as the Cr(VI)-induced DNA strand breaks,19 and that such DNA strand breaks in hepatocytes also change in direct proportion to the GSH content. 20,21 These observations were interpreted as implying that the reduction of chromate by GSH to some reactive intennediate is an important step in the chromate carcinogenicity. 20.21 In · the present undenaking22 we have used electron spin resonance (ESR) and spin-trap methodology to investigate the reduction of chromate by GSH and find evidence for the involvement of the glutathionyl radical (GS ·) as well as Cr(V)-intermediates."

Jan 1, 1990

By John A. Organiscak

Enclosed cabs are a primary means of reducing equipment operators? silica dust exposure at surface mines. The National Institute for Occupational Safety and Health experimentally investigated various factor effects on cab air filtration system performance. The factors investi­gated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use, and wind effects on cab particulate penetration. Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that intake filter efficiency and recirculation filter use were the two most influential factors on cab penetration performance. Use of the recirculation filter reduced cab penetration by usually an order of magnitude over the intake air filter alone because of the multi­plicative filtration of the cab interior air. Intake air leakage and filter loading affected the cab penetration to a lesser extent, while wind had the least impact on cab penetration between the calm and 10-mph wind velocities tested. Adding an intake pressurizer fan notably increased intake airflow and cab pressure with only minor changes to cab penetration. A mathematical model was developed that describes cab penetration in terms of intake filter efficiency, intake air quantity, intake air leakage, recirculation filter efficiency, recirculation filter quantity, and wind penetration.

Nov 1, 2008

By R. E. Head

At the microscopic laboratory of the Bureau of Mines Intermountain Experiment Station, Salt Lake City, Utah, efforts are being made to devise methods of differentially coloring finely crashed minerals as a means for their identification. Staining would facilitate sight recognition of minerals under the microscope and would be of great value in the study of crushed ores, concentrates, and tailings. Since the treatment of ores for their beneficiation is primarily based on the recovery of the minerals containing the clements of value, it is extremely important that these minerals should be known and that a method for quickly determining them when in minute fragments should be available. Herein lies one of the greatest uses for color methods. In many cases it is a difficult matter for even the trained petrographer and mineralogist to identify finely crushed minerals quickly. Although ordinary petrographic methods are accurate, they are often time--consuming and are not suitable to the needs of millmen who require, especially in the examination of tailings a method for determining minerals by inspection.

Jan 1, 1929

By John A. Organiscak

Enclosed cabs are a primary means of reducing equipment operators? silica dust exposure at surface mines. The National Institute for Occupational Safety and Health experimentally investigated various factor effects on cab air filtration system performance. The factors investi­gated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use, and wind effects on cab particulate penetration. Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that intake filter efficiency and recirculation filter use were the two most influential factors on cab penetration performance. Use of the recirculation filter reduced cab penetration by usually an order of magnitude over the intake air filter alone because of the multi­plicative filtration of the cab interior air. Intake air leakage and filter loading affected the cab penetration to a lesser extent, while wind had the least impact on cab penetration between the calm and 10-mph wind velocities tested. Adding an intake pressurizer fan notably increased intake airflow and cab pressure with only minor changes to cab penetration. A mathematical model was developed that describes cab penetration in terms of intake filter efficiency, intake air quantity, intake air leakage, recirculation filter efficiency, recirculation filter quantity, and wind penetration.

Jan 1, 2008

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

MINE VENTILATION NETWORK ANALYSIS

Jan 1, 1977

By M. Carrales

This Bureau of Mines publication presents short-range projections of domestic liquid hydrocarbon production through 1980. Appraisal of future crude oil production was made by evaluating the relationship between primary and enhanced oil recovery and the total crude oil producing trends in each of the oil-producing areas of the United States. Future natural gas liquid production was generally estimated by projecting historical production. Estimates of production were prepared for each of the oil producing areas and summarized for the Petroleum Administration for Defense (PAD) districts and total United States. From 1975 to 1980, crude oil production for the conterminous United States is expected to decline from 7.8 to 6.4 million barrels of oil per day (BOPD), and it is expected to increase from 8.0 to 8.2 million BOPD for the total United States. However, these estimates do not include additional production expected from the Elk Hills field in California and the Yates field in Texas. If included, 1980 production for the conterminous United States would be 6.7 million BOPD and 8.4 million BOPD for the total United States.

Jan 1, 1977

By Paul R. Amyotte, Omotayo Kalejaiye, Kenneth L. Cashdollar, Michael J. Pegg

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRI, 20-L and Fike 1 -m3 dust explosion chambers. The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1 -m3 and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.

By Michael J. Magyar

This report contains a cost estimate of the Bureau of Mines process for dewatering Alaskan placer effluent streams with polyethylene oxide (PEO). In this process effluent slurry is withdrawn from the placer plant pond system after a primary settling stage. A dilute PEO solution is injected into the slurry line to flocculate the fine, suspended solids. The flocculated solids are dewatered on a stationary screen. Clarified water is returned to the placer operation or discharged, while the 35 percent solids waste is pumped back into the mine cut. Cost estimates are presented for dewatering plants processing 1,000 gallons per minute of effluent slurry at three representative turbidity levels. Both the placer and the dewatering plants operate on the same 1-shift-per-day, 6-day-per-week schedule for the 100-day Alaskan operating season. Estimated fixed capital costs for these plants processing placer with effluent turbidities of 1,000, 3,000, and 5,000 nephelometric turbidity units (NTU) are approximately $29,000, $31,000, and $34,000, respectively, on a fourth quarter 1986 basis. Operating costs are estimated to be $0.34, $0.37, and $0.40 per thousand gallons of effluent slurry.

Jan 1, 1987

By Arnold B. Hubbard

This report describes a method of concentrating the insoluble organic material (kerogen) in a rich Colorado oil shale without any apparent alteration of its original chemical form. The method involved treating finely pulverized shale with dilute acetic acid at room temperature to remove the carbonates, which act as a cementing agent for the shale, and cause the shale particles to partly disintegrate into the organic and inorganic components. The acid-treated shale then was centrifuged in different liquid mediums ranging from 1.4 to 1.15 gravity to effect a mechanical separation. From a Colorado oil shale containing 48.0 percent ash, kerogen concentrates containing 43.3 to 8.7 percent ash were obtained. The carbon:hydrogen ratios of the kerogen in the original shale and the different concentrates were essentially the same. The oil:kerogen ratios calculated from Fischer assays of the above samples were essentially the same, regardless of the organic or inorganic contents. This was also true of the assay water:kerogen ratios of the same samples. These data indicate that no significant change occurred in the kerogen during the concentration process.

Jan 1, 1952

By John W. Buch

Hydraulic cutting tests made on samples of Pennsylvania anthracite (3,700 psi and 260 gpm) were promising enough for the Bureau to establish a full scale experiment in an anthracite mine. Water pressure and quantity for mining anthracite were arbitrarily established at 5,000 psi and 300 gpm (1,000 hp). For full-volume flow, hydraulic pressure is controlled by orifice size with the displacement pump. The hydraulic jumbo was designed for maneuvering on pitches from 0° to 20° in any direction and for a coalbed ranging in thickness from 10 feet 6 inches to 15 feet. All motions of the jumbo are by oil hydraulics. Jet flow is controlled (start-stop) at the face, through an interlocked pushbutton system. One button is in the operator's cab; one, at the pump station; and one (a safety shutoff), near the mining face. To December 1962, 7,400 tons of bed material had been mined at an average rate of 0.800 ton per minute, with an average power requirement of 14.125 kilowatt-hours per ton. In January 1963, the objective was changed from an engineering-development basis to a research basis--to determine, ultimately, the most efficient level of operating characteristics for maximum response, as measured by mining-out rate. This research phase of the project is not yet complete, but conclusions, and the method of arriving at them, will be made the subject of another Bureau publication. It should be noted that as of December 1963 nearly 13,000 tons of bed material had been mined, at rates as high as 1. 3 tons per minute for a complete face advance.

Jan 1, 1965

By James P. Bennett

The Bureau of Mines investigated the role of imported natural flake graphite in dolomite-carbon refractories used in steelmaking processes. Fundamental engineering data were obtained to enable the evaluation of substitute materials. Changes in oxidation resistance (2,000° F), hot strength (2,750° F), and deformation under load (2,7500 F) caused by 10-wt-pct additions of five different kinds of natural flake graphite and increasing quantities (0 to 30 pct) of a 90-pct-carbon natural flake graphite were studied. Results indicated that carbon purity of 10-wt-pct-graphite additions did not influence hot strength or deformation under load. When the quantity of 90-pct-carbon graphite addition varied between 0 and 30 wt pct in a dolomite-carbon brick, hot strength was highest and de-formation under load lowest with 10-wt-pct additions. As hot strength test temperature was increased from 5000 to 2,750° F, the strength difference observed between 0-and 30-wt-pct additions of a 90-pct-carbon graphite became smaller. Additions of a boron-treated graphite caused significantly higher strength and lower deformation under load at high temperatures, while an addition of ball clay significantly reduced strength and increased deformation.

Jan 1, 1987