Search Documents

By Michael J. Sapko, Gregory M. Green, Kenneth L. Cashdollar

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted a joint survey to determine the range of coal particle sizes found in dust samples collected from intake airways of US coal mines. The last comprehensive survey of this type was performed in the 1920s. The size of the coal dust is relevant to the amount of rock dust required to inert the coal dust, with more rock dust needed to inert finer sizes of coal dust. Dust samples were collected by MSHA inspectors from several mines in each of MSHA's 10 bituminous Coal Mine Safety and Health Districts. Samples were normally collected in several intakes at each mine. The laboratory analysis procedures included acid leaching of the sample to remove the limestone rock dust, sonic sieving to determine the dust size, and low-temperature ashing of the sieved fractions to correct for any remaining incombustible matter. The results indicate that particle sizes of mine coal dust in intake airways are finer than those measured in the 1920s. This finer size coal dust in intake airways would require more incombustible matter to be effectively inerted than the 65% incombustible specified in current regulations.

By R. Luhrman, E. Christ, B. Gores, S. Fischer, E. Johanning

North American railroad locomotive operators (engineers and conductors) are exposed to multi-axis vibration and shocks (1, 2). A recent epidemiological survey showed a prevalence of serious type of neck and lower back disorders nearly double that of a control group (3). Ergonomic working conditions are important co-factors in a vibration and shock exposure risk assessment (4, 5). The goal of this study is to illustrate typical work stations (cabs and seats) in US/Canadian type locomotives and assess shock related exposure risk by calculations of the new proposed shock risk indicators according to the new ISO 2631-5 (2004) (6). Methods Locomotive cab and seat inspections were conducted and operators’ activities were assessed by a trained observer. Field measurements (n=50) were obtained during normal revue service following generally accepted guidelines (ISO 2631 (1)). A sub-sample of n=20 locomotives were selected for the calculation of proposed shock indicators (ISO 2631 (5)). Results There has been little change in basic locomotive cab and seat design in the U.S.. Two locomotive cab design concepts are used: the Association of American Railroad (AAR) Control Stand and in newer series wide-body locomotives the “Control Consol” (Figures 1-2), with varying seating conditions, but frequently subjecting the operator to an awkward body posture in addition to the vibration and shock exposure. [ ]

Jan 6, 2006

By J. E. Hamak

This publication contains analyses and related source data for 162 natural gas samples from 15 states and 4 foreign countries. Of the total samples, 154 were collected during calendar year 1992. The remainder were collected earlier, but releases granting permission to publish were not received until 1992. None of the analyses have been previously published in annual reports. All samples were obtained and analyzed as part of U.S. Department of the Interior, U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free-market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1993

By Jueun Lee, Jong-Hwa Yoon, K. Rider, Bernard J. Martin

Whole body vibration is known to affect movement accuracy [1], however little is known about changes in the organization of movement and movement strategies used to limit the influences of perturbations. The specific aim of this work is to analyze the motion and coordination of upper body segments of seated operators performing reaching tasks under whole-body sinusoidal vibration exposure and simulated vehicle ride motion. The long-term objective is to model reach coordination and predict the dynamic behavior of the upper body motion under vehicle vibration exposure. Method The reach task consisted of pointing with the right hand index finger to targets located on touch screens placed in front of the subject, 45° overhead and 90° to the right in the mockup cabin of an HMMWV placed on a 6 DOF ride motion simulator. The task was performed under stable (no vibration) and vibration (sinusoidal vibration or simulated ride motion) conditions. A motion capture system was used to record kinematic data of reflective markers to recreate body link trajectories. Joint angles (torso, shoulder and elbow; Figure 1) were then computed using quaternions. Coordination between body links was defined as a) the joints angle-versus-angle relationships between the upper arm and lower arm, and b) the joint motion onset relationships between torso, upper arm and lower arm in the time domain. Results Angle–versus-angle relationships. The relationship between upper arm vs. lower arm angle and torso vs. upper arm angle for a far forward reaching movement in the stable (solid lines) and vibration conditions (dotted lines) are illustrated in Figure 2. Fig 2A compares the control condition with a 4 Hz lateral vibration while Fig 2B compares the control condition with a 6 Hz vertical vibration. It appears that under vibration exposure the reduced upper arm extension is compensated by an increase in torso flexion. This effect is seen in the last phase of the movements (encircled areas). In addition, the lower arm extension is delayed under 6 Hz vertical vibration (Fig 2B left panel). Time of joint motion onset. The timing relationship between torso, upper arm and lower arm is largely a function of the target to be reached. Examples of delays between body links are illustrated in Figure 3. The control condition is compared to a 6 Hz vertical vibration for three

Jan 6, 2006

By Michael J. Jorgensen, Anoop Polsani, Khurram S. Khan

Riveting operations in aircraft manufacturing involves the use of power tools for manually drilling holes for the rivets, power drills for the setting of the holes for the rivets, as well as rivet guns to drive and set the rivets. To close the rivet, the rivet is driven against a metallic bar commonly called a “bucking bar”. The bucking bars are typically held firmly to increase the quality of the riveting, as well as keep the bucking bar from “dancing” against the metal piece being riveted. Thus, employees in aircraft manufacturing involved in riveting are exposed to hand-arm vibration from several sources, and epidemiological evidence suggests that vibration-related musculoskeletal disorders are associated with long term exposure to riveting tasks in the aircraft manufacturing of aircraft.1,2 Recently, tungsten technology has been introduced into aircraft manufacturing for bucking bars, which are heavier than traditional steel bucking bars of the same size. Rivet guns with tungsten pistons instead of steel pistons have also recently been introduced with the objective of reducing vibration exposure to the riveter. The objective of this study was to assess vibration characteristics of steel and tungsten bucking bars and rivet guns to identify the combination that simultaneously reduced the combined exposure to both the “riveter” and “bucker”. Methods Vibration (10g tri-axial accelerometer, Biometrics S2-10G-MF Series 2) was measured from eight experienced employees using seven different rivet guns on size 6 rivets, with the same person bucking for all subjects. Vibration was also measured on two different bucking bars for these same eight subjects, with the same person driving the rivets using the various rivet guns. The rivet guns consisted of three E4 steel piston guns with different RPMs (Guns A-E4, B-E4, C-E4), an E4 vibration dampened rivet gun (Gun D-E4D), an E3 steel piston rivet gun (Gun E-E3) and an E3 and E4 tungsten piston rivet guns (Guns F-E3T and G-E4T). The bucking bars were made of 90% tungsten (1694g) and cold-rolled steel (843g), and were the same shape and size. A two-way repeated measures analysis of variance was performed on the vibration (mean frequency weighted resultant acceleration) on both the rivet gun side and the bucking bar side, and mean rankings were used to assess the vibration simultaneously for the rivet gun and bucking bars to investigate which combinations provided the lowest vibration exposure. Results Frequency weighted resultant acceleration was significantly lower on the E3 tungsten (F-E3T) rivet gun than the E4 steel piston (B-E4) and the E4 tungsten piston (G-E4T) rivet guns (Figure 1). When measuring vibration on the bucking bar, the E4 (A-E4) steel piston rivet gun resulted in lower vibration on the bucking bars than the E4 tungsten piston (G-E4T) and E4 vibration dampened (D-E4D) rivet guns (Figure 2). Additionally, use of tungsten bucking bars resulted in a 35% decrease in resultant frequency weighted acceleration than when using steel bucking bars.

Jan 6, 2006

By Robert H. Mattes

The Lake Lynn Laboratory is a multipurpose mining research laboratory operated by the Bureau of Mines and located in Fairchance, Pa, It consists of both surface and underground facilities. The initial focus of the facility, scheduled for full operation in fall 1982, will be on the problems of fires and explosions in mines. The initial experimental explosion was fired on March 3, 1982. The intent of this document is to provide the reader with detailed information on the physical capabilities of the Lake Lynn Laboratory. Subsequent publications will focus on the capabilities of Lake Lynn as compared with those of other similar facilities worldwide, and a comparison of initial explosion test results realized at Lake Lynn and comparable results from the Bruceton Experimental Mines.

Jan 1, 1983

By J. L. Eakin

The works and opinions of experts on well stimulation and related problems are summarized in this paper. The material is devoted to stimulative work in petroleum and natural-gas wells exclusive of the generally applied pressure maintenance and secondary-recovery methods. Its purpose is to review a collection of recent and available material on well-stimulation methods and techniques. Each separate discussion is accompanied by a selected bibliography. An author index is included.

Jan 1, 1964

By J. L. Eakin

The works and opinions of experts on well stimulation and related problems are summarized in this paper. The material is devoted to stimulative work in petroleum and natural-gas wells exclusive of the generally applied pressure maintenance and secondary-recovery methods. Its purpose is to review a collection of recent and available material on well-stimulation methods and techniques. Each separate discussion is accompanied by a selected bibliography. An author index is included.

Jan 1, 1964

By W. P. Diamond

The direct method test was developed for general mine safety applications by the U.S. Bureau of Mines in the early 1970's to measure the gas content of coal samples obtained from the relatively shallow depths of eastern U.S. coal mines. Over time, applications for gas content data evolved which required increasingly accurate desorption values. It became evident that some of the inherent weaknesses in the original direct method test could best be addressed by abandoning the water displacement based desorbed gas volume measurements. The ideal gas law based modified direct method (MDM) and associated desorbed gas volume measurement apparatus was developed to provide the most accurate desorption values possible for rock samples obtained from any gas-bearing strata. The MDM has a number of significant advantages, including: (1) increased accuracy, especially for low gas content samples, (2) a test apparatus with an integral sampling port to facilitate the collection of uncontaminated gas samples, (3) an inherent head space effect correction in the periodic MDM desorbed gas volume calculations, (4) measurement of positive and negative desorbed gas volumes, (5) elimination of differential gas solubility effects as a source of error inherent in the water displacement methods, and (6) a compact and rugged test apparatus that along with the elimination of the ?glassware? required for the water displacement methods, facilitates its use in the field.

Jan 1, 2008

By Jeffrey A. Aldinger

This U.S. Bureau of Mines report presents an analysis of surface coal mining accidents involving mobile equipment for the years 1989 through 1991. Mobile equipment is defined as haulage trucks, front-end loaders, bulldozers, scrapers, and road graders. These five pieces of mining equipment accounted for 20 pct of all surface coal mine accidents and 41 pct of the fatalities. The general discussion of these accidents covers the accident causes, the primary activity of the accident victims, and other contributing factors. A more detailed analysis of accidents associated with each piece of mobile equipment is also provided. This report will provide mine managers and mine safety personnel with a better understanding of the hazards associated with mobile mining equipment. It identifies where improvements in mobile equipment safety can be made and those areas requiring additional safety emphasis, such as safety training, work procedure changes, or engineering changes to the equipment or work environment. The analysis was performed by a team of researchers using accident data and narratives provided by the Mine Safety and Health Administration.

Jan 1, 1995

By E. G. King

Heat of formation values for mercuric sulfide appear in all the comprehensive listings of thermodynamic data, but experimentally determined entropy values have been lacking. Consequently, all free energy calculations involving mercuric sulfide have been based upon estimated entropy values. This paper reports Bureau of Mines measurements of the low-temperature heat capacity of red mercuric sulfide (cinnabar) and the entropy value at 298.15° K. derived therefrom. The entropy value was combined with heat data to obtain free energy values for the formation of red mercuric sulfide from liquid or gaseous mercury and from rhombic or gaseous diatomic sulfur.

Jan 1, 1962

By G. B. Shea

In the search for possible future sources of petroleum products, the recovery and utilization of bitumens from the large outcropping deposits of bituminous sandstones in the United States have been under study by the Bureau of Mines for the past several years. The results of laboratory research in the adaptation of the hot-water separation process to recovery of bitumen from bituminous sandstones were reported in an earlier publication, on the Edna deposits near San Luis Obispo, Calif. This publication included analytical data on the cracked products and asphalts obtained from the extracted bitumen and on the cracking and distillation of the bitumen. Comparable hot-water separation tests have been run in the San Francisco, Calif., laboratory of the Bureau of Mines on quarry samples from the large deposits of bituminous sandstones near Vernal and Sunnyside, Utah. The bitumens were isolated from the extracts of the separation plant and analyzed at the Petroleum and Oil-Shale Experiment Station of the Bureau of Mines, Laramie, Wyo. Part I of this report summarizes the general characteristics of the Vernal and Sunnyside deposits and discusses the hot-water separation process as applied to those bituminous sandstones and the results obtained. The separation tests showed that these bituminous sandstones also respond to treatment by the hotwater method of separation. The bitumen in the Vernal sandstone was extracted more readily by the action of hot water than was the Edna bitumen, which greatly simplified plant operation. The Vernal sandstone contains no water-soluble iron compounds, such as were found in the Edna sandstone, and, therefore, required no preliminary water washing. Recovery of bitumen from the Vernal sandstone was about 96 percent.

Jan 1, 1952

By Steven J. Knoll, Theodore J. Williams, Douglas F. Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because it can result in failures of ground that lead to both injuries and death. Spokane Research Laboratory personnel investigated electromagnetic (EM) emissions in a deep underground mine in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results suggest that (1) there is no increase in the number of EM emissions prior to recorded seismic activity, (2) some EM signals are generated during blasting, (3) interference from mine electrical sources mask seismic-generated EM signals, (4) EM emissions do not give enough warning (compared to seismic monitoring) to permit miners to leave a stope, (5) the distance an EM signal can travel in the rock is between 18 and 40 m, and (6) current data acquisition systems do not differentiate between EM signals generated from seismic activity and random mine electrical noise. These results preclude monitoring EM emissions as precursors of impending catastrophic ground failure.

By C. F. Wingquist

As part of an ongoing study to determine how the wear of mining tools affects dust generation, the Bureau of Mines has measured bit tempera-ture rise during cutting of abrasive rock. Radial bit wear-flat tem-peratures generated by linear cutting in Berea Sandstone were measured as a function of cutting depth and speed. Depths of cut (DOC) were 1/8, 1/4, and 1/2 in, and cutting speeds were 10, 40, and 80 in/s, respectively. Temperature sensing was accomplished by emplacement of a miniature thermocouple into the center of the wear flat. Temperatures observed ranged from 2000 to 5000 C. Correlation between depth and temperature was weak. Temperature increased linearly with speed at 1/2-in DOC, but data taken at 1/8-and 1/4-in DOC produced inconclusive results. The results indicated that at least for deeper cuts (1/2 in), bit temperature, and therefore wear, can be reduced by lowering the cutting speed.

Jan 1, 1987

By Jeffrey M. Listak

The National Institute for Occupational Safety and Health (NIOSH) conducted field tests to evaluate the effectiveness of a wet head continuous mining machine for reducing dust exposure for continuous miner operators. Wet head technology delivers water via sprays to the continuous miner's cutter head as opposed to traditional standard sprays located on the boom and body of the mining machine. The sprays, positioned directly behind each bit on the cutter head, deliver water at the point of attack, serving to cool the bits during mining to reduce the potential for frictional ignitions. The sprays also flood the coal with water to potentially suppress dust generation. Dust surveys were conducted at several mines to evaluate the wet head's effectiveness to control respirable dust exposure at the continuous miner operator location and in the immediate return. Results show that the wet head miner improved air quality at both locations to varying degrees in some cases and not in others when compared to a continuous miner with a standard spray system.

Jan 1, 2010

To reduce the exposure of mining machine operators to respirable dust. Approach: A protective curtain of filtered air is blown down around the operator's head, from a manifold mounted on the machine canopy. How It Works: Mine air is drawn into the system through a filter which removes respirable dust. The filtered air enters a centrifugal blower which pushes it through a flexible hose to a manifold mounted on the canopy above the operator. Air leaves the manifold through a perforated plate and flows down around the operator's head. A photograph of an installed system can be seen in Figure 1. The second photograph, Figure 2, shows the sys-tem components. An important advantage of this dust protection system is that it is not worn or carried, or in any way connected to the operator. It is therefore not uncomfortable, encumbering, or

Jan 1, 1976

By John Organiscak

A majority of continuous mining machines employ a water spray system and a machine mounted flooded-bed scrubber to suppress and capture dust during coal mining. These machine mounted dust control systems must be designed to function within the localized face ventilation system at the mining section to control both dust and methane. Spray systems can impede or improve the scrubber effectiveness in controlling dust or methane at the mining face. Laboratory experiments were conducted to examine the effect of spray type, spray pressure, machine body blocking sprays, and scrubber airflow on dust and gas levels while using a 12.2 m (40 ft) exhaust ventilation curtain setback from the face. These experiments were conducted with the mining machine positioned at the end of a simulated 6.1 m (20 ft) sump and slab cut. Results indicate that the hollow cone nozzles with blocking sprays best complemented the flooded-bed scrubber performance in an exhaust ventilation system. This external spray system notably reduced dust and gas levels on the off-curtain side of the mining machine for both the sump and slab cut as compared to the flat spray nozzles. Higher scrubber airflows reduced dust and gas levels on the curtain side and in the return of the continuous mining machine. The remote operator position, located on the off curtain side and parallel to the inlet end of the exhaust curtain, sustained the most stable and lowest dust levels around the mining machine.

Jan 1, 2010

By Gerrit V. R. Goodman

A laboratory study assessed the impacts of water spray pressure, face ventilation quantity, and line brattice setback distance on respirable dust and SF6 tracer gas concentrations around a continuous mining machine using a sprayfan or directional spray system. Dust levels were measured at locations representing the mining machine operator and the standard and off-standard shuttle car operators, and in the return airway. The results showed that changes in all three independent variables significantly affected log-transformed dust levels at the three operator sampling locations. Changes in setback distance impacted return airway dust levels. Laboratory testing also identified numerous variable interactions affecting dust levels. Tracer gas levels were measured on the left and right sides of the cutting drum and in the return. Untransformed gas levels around the cutting drum were significantly affected by changes in water pressure, face ventilation quantity, and setback distance. Only a few interactions were identified that significantly affected these concentrations. Gas levels in the return airway were grouped by face ventilation quantity. Return gas levels measured at the low curtain quantity were generally unaffected by changes in water pressure or curtain setback distance. At the high curtain quantity, return airway gas levels were affected by curtain setback distance. A field study was conducted to assess the impact of these parameters in an actual mining operation. These data showed that respirable dust levels may have been impacted by a change in water pressure and, to a lesser extent, by an increase in curtain setback distance. A series of tracer gas pulse tests were also conducted during this study. The results showed that effectiveness of the face ventilation was impacted by changes in curtain flow quantity and setback distance. Laboratory testing supported similar conclusions.

Jan 1, 2004

By Albert H. Clough

The West Lynn Canal subarea of the Juneau Mining District (JMD) is defined by Lynn Canal on the east, Davidson Glacier to the north, Icy Strait to the south and the Glacier Bay National Park Boundary to the west (figs. C-l and C-2). This area extends along the main-land west of Juneau (across Lynn Canal) northerly, to approximately 20 miles south of the city of Haines. The only roads in the area are relatively new logging roads at the southern end constructed to support a U.S. Forest Service timber sale. There is also local road access near the community of Excursion Inlet. Access to the remainder of the region is either by boat, aircraft, or 'foot. Helicopters provide the only time effective access to all but the coastal parts of the West Lynn Canal subarea. Coastal areas may be reached by small boat or float aircraft. There is an unimproved dirt airstrip just north of the mouth of the Endicott River. This airstrip is suitable for use by light aircraft. The subarea lies within the Tongass National Forest and is managed by the Department of Agriculture, U.S. Forest Service. Approximately two-thirds of the forest lands are open to mineral entry under the current Tongass Land Management plan. The remaining forest lands comprise the Endicott River Wilderness area, which is closed to mineral entry. Private lands within the study area are sparse, with scattered homestead tracts along the coastal regions and in the Excursion Inlet area. Sealaska (Southeast Alaska Regional Native Corporation) also has land selections in the southern Chilkat Range. Tidal and submerged lands are owned by the State of Alaska.

Jan 1, 2012

By H. M. Smith

The production of oil during the early development of new oil fields is usually accompanied by large quantities of natural gas. Since in most fields gas under pressure is the main source of the energy causing the oil to move through the sands into the wells and thence to the surface, coincident production of natural gas will continue as long as present-day producing methods are used. Generally the use of this gas is restricted, since markets are not readily available. Consequently, a large portion of the gas produced is often wasted by being blown into the air. The magnitude of gas waste is well brought out in the following statement by Miller: Only a few outstanding examples need be cited to show the enormous production of gas that accompanies the discovery of new sources. In April, 1927, the Ventura field produced approximately 210,000,000 cubic feet of gas a day; and during the summer of 1927 Alamitos Heights reached a peak gas production of 102,000,000 cubic feet a day; on December 1, 1928, as a result of the summer's deeper drilling in the Long Beach field, surplus gas production amounted to 125,000,000 cubic feet a day. It is estimated that in January, 1929, the Santa Fe Springs field will have a daily gas production of 387,000,000 cubic feet from the recently discovered Buckbee oil zone. Of this amount 274,000,000 cubic feet a day will be the surplus above the amount required for field and plant fuel, taken out by utility corporations, and that used in repressuring the Meyer sand which lies above the Buckbee zone. Another example of the waste of large volumes of gas is in the Turner Valley field of Canada, 6 where 250,000,000 cubic feet of gas is being burned daily in flambeaus, as there is no present outlet except at prohibitive cost.

Jan 1, 1931