Search Documents

By T. L. Joseph

"IntroductionThe efficiency of ore reduction in the blast furnace and fuel requirements depend upon the degree of uniformity with which reducing gases can be distributed through the stock column and upon the permeability of individual pieces of ore and sinter. If the ore is fine, the major problem in reduction is to get the ascending gas stream to the surface of the ore-Hard, dense ores of low permeability, mined in coarse sizes, tend to improve the permeability of the bed, but unless they are crushed to the proper size they reach the hearth unreduced.Surveys by the Bureau of Mines have shown conclusively that the gas distribution in the upper three fourths of the furnace is far from ideal. Furnace lines, top design, and methods of charging are important, but more thorough size preparation of the ore is necessary to eliminate size segregation at the stock line, which inevitably leads to non-uniformities in gas distribution.Because of the quantity of sinter now produced close study of the characteristics which determine its behavior in smelting is warranted. As the use of concentrates increases agglomeration will become more of a necessity. Improvements in the physical character of the ore burden are particularly important to plants using coke of poor physical quality. In addition to aiding reduction, improved physical properties of the ore burden will permit the use of higher blast heats, which is equally important.Reduction Tests on Fine Sizes of SinterPrevious reduction tests on minus 0.742— plus 0.525--inch pieces of commercial sinters revealed large differences in porosity and reducibility. The results have been published in a former report. 3 Although the physical properties of the sinter, particularly porosity, were found to be of major importance in determining the rate of deoxidization, it appeared that certain chemical properties of the sinter appreciably retarded the reduction of sinters high in silica. This was attributed to the presence of fayalite, which has been identified by Schwartz and by Luyken and Kraeber4 as an important constituent of sinter. Although furnace operators and metallurgists have assumed that iron silicate is more difficult to reduce than hematite or magnetite, definite data on the reduction characteristics of this material were not available. Tests were undertaken, therefore, to develop a method for de-termining the amount of iron silicate present in sinters so that its effect upon reduction could be observed."

Jun 1, 1934

By Elaine T. Cullen

Underground mining, like many high-risk industries, is facing a crisis in the near future. This industry has traditionally relied on a master-apprentice relationship to train new workers, but experienced miners are retiring in large numbers, leaving few "masters" to properly train their replacements. With a recent resurgence in mining, many new miners are entering the workforce each day. The rise in the number of inexperienced workers has implications for worker safety in an industry in which one mistake can blow up the entire workplace. The explosion in the Darby Mine in May 2006 that killed five miners illustrates what can happen in hazardous environments such as underground mines. The Health Communications Team at the National Institute for Occupational Safety and Health Spokane Research Laboratory was asked to address this problem by developing new training and safety awareness materials to promote safe flame cutting and welding practices. This article describes how occupational ethnographic techniques provided insights needed for "new product development." The result of this work was a national initiative to raise awareness and to protect underground coal miners from the dangers of flame cutting and welding in an environment filled with solid fuel and methane (natural gas). Although this project was initially designed for the mining industry, the approach and lessons learned are applicable to any high-risk industry and should be of interest to other social marketing or occupational safety and health professionals.

Jan 1, 2009

By McHenry Mosier

This paper constitutes the third progress report on a national survey of the use of detachable bits in metal mines. It presents comparative costs of drilling with conventional and detachable bits and describes the operating practice in rock drilling and the reconditioning of drill steel and bits at 10 mines not discussed in previous reports.3/ ACKNOWLEDGMENTS This report has been prepared with the assistance and cooperation of the officials and staff members at the mines visited. Costs and other data at individual mines were developed and furnished by the operators.

Jan 1, 1937

By E. J. Matson

"The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States since 1939. Projects were set up on only the most promising properties.A preliminary examination of the Mount Hope mine was made in January 1943 by the Bureau's engineers, who recommended exploration by diamond drilling.The mine is in the unsurveyed portion of T. 22 N., R. 1 E., Mount Diablo base and meridian, south-central Eureka County, Nevada, 25 miles by road north of the village of Eureka. A partly graded and Graveled secondary road connects the mine and Eureka on U. S. Highway 50.Extensive sampling was done by the Bureau in February. 1943. Core drilling from the surface was started on March 15, 1944, and completed on April 2, 1545. The 16 holes drilled totaled 7,215 feet. The mining company also did extensive underground core drilling from April 21, 1944, to January 4, 1945. This report gives the results of core drilling supervised by the Bureau of Mines.The drilling program was designed to explore for extensions of the mineralization exposed in the mine workings. As a result of drilling, additional ore was found, and it is believed that this project has fulfilled the purpose for which it was planned.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization, of our mineral resources to the end that they make the greatest possible contribution to na¬tional security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples of ore and performs beneficiation test. Both these branches are under the supervision of Dr. R. S. Dean, assists director.With respect to this report special acknowledgment is due to Charles W. Merriam of the United States Geological Survey for his interpretation of the Mount Hope mine Geology and his cooperation throughout the project; Col. Leverett Davis, former lessee of the property; K. K. Hood, manager of the Mount Hope Unit, Callahan Zinc-Lead Co., Inc.; C. P. Knaebel, assistant manager, and M. P. Nackowski, geologist, of that company, for their help, and to the Sullivan Machinery Co. for its assistance."

Aug 1, 1946

By Robert J. Evans

The Bureau of Mines is sponsoring a variety of long-term, high-risk research to advance state-of-the-art technology in U.S. underground coal mining. This report reviews the status of many Bureau projects that support fundamental underground coal mining operations; the project areas include cutting coal from the solid (extraction), hauling coal from the face (transport), and activities that sustain daily operations (logistics). Innovative equipment and technology have been developed, with these major objectives: to significantly improve coal mine productivity, to further advance coal recovery and personal safety within the mining industry, and to reduce the time needed to develop longwall panels. The majority of the prototype equipment covered in this report either has undergone or will undergo comprehensive evaluation at Bureau surface test facilities so that performance and reliability can be improved before the equipment is tested and evaluated in a working section underground.

Jan 1, 1988

By J. B. Rosenbaum

This report presents new findings and consolidates previously published data to provide a single reference containing a concise and comprehensive description of the Bureau's work on electrolytic chromium. Two separate systems for electrolytic-chromium recovery were developed, one designated as the oxidized system the other as the reduced system. The electrowinning of chromium metal follows the dissolution of chromium from the ore or from ferrochrome and its separation from gangue and metallic impurities. Chromite was first solubilized by pressure digestion at slightly elevated temperatures in an oxidized acid solution using Na2Cr2O7 as an oxidizing agent. Later it was found that a sodium-free electrolyte was preferable, using return-cell anolyte containing H2SO4 and Cr03 as the oxidizing agent. Gangue materials were separated from the soluble metallics by filtration; and, after the Cr+3 had been stabilized, the metallic impurities were separated as crystalline ammonium salts by vacuum crystallization.

Jan 1, 1957

By Xintan Chang

MFIRE is a computer simulation program that performs normal ventilation network planning calculations and dynamic transient-state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under the influence of natural ventilation, fans, fires, or any combination of these. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters such as the development of new mine workings or changes in ventilation control structures, external influences (varying outside temperatures), and internal influences (fires). Extensive output enables detailed, quantitative analysis of the effects that the alteration will cause to the ventilation system. The program was developed at Michigan Technological University (MTU), Houghton, MI, with support from the Bureau of Mines. A personal computer (PC) version of the program was completed under contract for the Bureau by MTU. The purpose of this report is to document the installation and use of the PC version of the program MFIRE.

Jan 1, 1990

By C. F. Jackson

This paper has been prepared as a progress report in connection with the series of articles on mining methods and costs which are being published by the U. S. Bureau of Mines in the form of information circulars. When enough circulars have boon completed it is planned to publish a more complete and comprehensive paper in bulletin form dealing with the subject of underground transportation. Progress reports, followed b., bulletins, will be prepared from time to time dealing with other subjects included in the general study of mining methods at individual nines, such as mine development, drilling, and blasting; stoping methods (each principal stoping method to be summarized in a separate paper); Ventilation; wage, contract and bonus systems, etc.

Jan 1, 1931

By F. S. Crawford

"After many years of safety activity in the United States in one form or another it becomes increasingly evident to those in contact with safety work that to achieve continuous good results in accident prevention there must be an aggressive organization behind the safety movement at each mine with fairly definite plan and policy. A study of the methods used by various companies and the results they have attained will be of value to the common cause of safety promotion.A study has been made of the safety records of the Menominee iron range in the Lake Superior district, and of data from the county mine inspector's report. Several companies on this iron range that have attained a certain measure of success in their work of accident prevention have given data, and a summary of their safety methods is presented.The Menominee iron range of Michigan lies in the southern portion of the upper peninsula of Michigan, bordering on Wisconsin. It consists of two main. divisions--the West Menominee Range, situated in Iron County in the vicinity of Iron River and Crystal Palls, and the East Menominee range situated in Dickinson County in the neighborhood or iron Mountain, Mich. The mines about Iron River and Crystal Falls are peculiarly subject to fires in a carbonaceous, sulphur-bearing black slate which appears in the footwall. This gives considerable trouble because fires in this material start from spontaneous heating. The methods of mining are top slicing and open stoping, working on benches along the sides of the stopes. The character of the ground varies from medium Soft ore to relatively hard ore which permits open stoping. Approximately one-third of the operating mines are equipped with a fan for main mechanical ventilation. The remainder are ventilated by natural draft. The East Menominee range is the older, top slicing having been used there for a number of years, and the timber mats have boon well developed. In common with all districts, some companies pay more attention to safety than others, although, those which do riot have the best records do pay some attention to safety.During the past three years the annual production per man employed has remained about constant, but in many mines a general decrease is shown in the accident record. The variation in the results attained can be ascribed mainly to the earnestness with which accident-prevention work is pursued, essentially regardless of the method of mining used. This is shown to be generally true, because the record indicates a steady decrease in one mine with an active safety department, while in adjoining mines with the same kind of ground and method of mining but where not such intensive attention has been paid to safety work, the accident record is high."

Oct 1, 1931

By David W. Tongue

This report describes the engineering work leading to the design of an underground coal mine piping system to transport approximately 2,000,000 cubic feet per day of methane gas to the surface from degasification holes drilled horizontally into the coalbed in existing coal mines. Safety instrumentation for detection of gas leaks and provisions for automatic emergency shutdown are included in the design. It also includes specifications for a safe system of handling gas, water, and drill cuttings during drilling of the horizontal holes and recommendations for compressor and metering facilities at the surface. The main pipeline is recommended to be constructed of polyethylene plastic pipe joined by a butt fusion method while lateral lines and separator and meter piping at the horizontal holes are recommended to be screwed steel piping. The materials used are to be resistant to the forces of impact exerted by falling rock. The pipelines are to be suspended from the ceiling with pipe hangers. All steel components are protected from chemical corrosion by applying protective coatings and the vertical casing to the surface is protected from electrolytic corrosion by a rectifier station. Methane gas detectors monitor the mine atmosphere to detect the presence of gas leaks and a pneumatic plastic tubing line provides for control of the safety shutdown system. Both the recommended design and the required construction procedures are in compliance with the applicable Federal codes for coal mine safety.

Jan 1, 2012

By Donelson A. Robertson

Includes a review of the state-of-the-art of explosives loading in the crushed stone and cement industries of South Florida and the development of a field test program for alternatives. Emphasis is on the loading of small diameter (2 1/4" or less) explosives. Test results ire evaluated for operational and economic feasibility. Details are described of an explosives loading method which involves placing cardboard tubes with external couplings through the hollow drill steel and then Loading explosives into the tube casings after the drill rig has moved off. This method eliminates the hazards peculiar to loading explosives Through the kelly bar. The alternative method can be performed by existing drill rigs with or without minor modification. With modification, improvement in yield per blasthole and/or primary crushing rate provides opportunity so offset some or all of the additional cost.

Jan 1, 1978

By George T. Krempasky

This report is one of a series of Bureau of Mines Information Circulars dealing with mining methods and costs throughout the United States. It describes drifting, crosscutting, and raising operations at several mines in the Coeur d'Alene mining district, Shoshone County, Idaho. Ore bodies in the Coeur d'Alene district are generally in steeply dipping tabular ore zones, are irregular in shape, erratic in occurrence, and have been extensively mined along the strike and down dip. Because of the extended attitude of the deposits a great deal of development work is required. Drifting, crosscutting, and raising methods are described in this report. Shaft sinking is the subject of another report in the same series.

Jan 1, 1960

This is the second of a series of reports on properties of commercial motor fuels made pursuant to a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data oil motor gasolines sold during the minter of 1935-36.3/ These gasoline surveys report results of inspections, in oil-company laboratories, of samples of gasoline obtained by representatives of oil companies from service-station pumps in marketing areas throughout the country. In the present survey are presented inspection data on 239 samples of regular- price gasoline, 166 samples of premium-price gasoline, and 157 samples of third-grade gasoline, a total of 562 samples collected during the summer of 1936.

Jan 1, 1937

By Frank D. McGuirk

Underground coal mining is traditionally hazardous. Although many danger-prone human activities are now performed by mechanized equipment, this mechanization has itself brought new dangers to the underground mining industry, and the loss of life and limb has caused increased concern for mine safety. The 1969 Federal Coal Mine Health and Safety Act has precipitated a great deal of safety-related research on the part of the Government, industry, and private agencies. Much of this safety research has been focused on the new and varied man-machine interfaces caused by increased mechanization. Recent projects in this area have dealt with standardized controls, emergency shutdown capabilities (panic bars, strike plates, self-centering controls, "dead man" controls), and machine operator protective devices (fully enclosed cabs, canopies, side rails). There was a need for integration of the findings of current and past projects to move rapidly toward the smooth, orderly implementation of standardized operator work station designs for underground mining equipment.

Jan 1, 1975

By Mary S. Esfandiary

U.S. scientists attempting to maintain continuous surveillance of scientific information are confronted with two acute problems: The steady, even spectacular; increase in the volume of such information and the fact that much of it is published in unfamiliar foreign languages, According to the National Science Foundation, almost one-third of the world's scientific literature is published in languages that are read by less than 5 percent of U.S. scientists. Most scientists in the United States must rely on abstract journals and translations to obtain information on developments in research and investigations conducted in the non-English-speaking countries. However, there are problems involved in procuring suitable abstracts and translations and in obtaining such information as cheaply and rapidly as possible.

Jan 1, 1961

By J. Douglas Causey

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 9,600 acres of the 12,350-acre Antelope Creek Wilderness Study Area (MT-065-266) in order to evaluate its mineral resources. Within this report, these 9,600 acres are referred to as the study area. The Antelope Creek Wilderness Study Area, Phillips County, MT, adjoins the north end of the Charles M. Russell Wildlife Refuge. Considered part of the Missouri River Breaks, the area straddles the edge of a thrust fault zone that has deformed the Mesozoic strata in the west half of the area. Shale, siltstone, and sandstone of Cretaceous Age are exposed in the area. Coal beds averaging 3.0 ft thick occur in the Judith River Formation. About 0.20 million short tons of coal were mined from the Judith River Formation adjacent to the west boundary of the area; no production is known in the study area.

Jan 1, 1986

By George B. Clark

The purpose of this investigation was to determine the feasibility of designing and testing the elements of a small charge blasting system which will eliminate, or reduce to acceptable levels, most of the undesirable features of current underground drill and blast systems, i.e., 1) air blast, 2) ground vibrations, 3) flying fragments, 4) overbreak and fracture of surrounding rock, and 5) the cyclic nature of drill and blast operations. The experimentation was conducted in tunnels in granite and the results indicate that the basic technical concepts of the project were achieved. The next step is to design, construct, and test a prototype machine.

Jan 1, 1976

By Robert Alfred

This paper is one of a aeries being published by the Federal Bureau of Mines on methods and practices used in mining and preparing crushed stone for market. Performance, in terms of units of work or tons produced per machine and per operator man-hour, is given whenever that information can be obtained. Direct operating costs are useful for comparing different methods and are included if available. In addition to descriptions of equipment and methods used the Bureau considered it desirable to discuss the engineering reasons for the choices that have been made, This paper is particularly concerned with the operation of the Liberty quarry and plant of the Campbell Limestone Co, The plant is in Pickens County, adjacent to the main line of the Southern Railway, and is about 18 miles west of Greenville, S, C. Access also is available by United States Highway No, 123, The company's main offices are at Knoxville, Tenn.

Jan 1, 1958

By James J. Snodgrass

The Bureau of Mines designed and constructed a series of calibration models for geophysical borehole logging. A nominal hole diameter of 3 inches was selected as representative of typical core holes drilled for mining and engineering purposes, although additional hole diameters of 2, 5, and 8 inches are provided in one of the models for determination of empirical correction factors for variations in hole diameter. The physical properties of the models were determined by laboratory analyses of drill core samples and evaluated statistically for reliability. This report outlines the location of the models, elements of design and construction, and results of the laboratory tests. The models are available at the Denver Federal Center, Denver, Colo., for use by Government agencies and private industry to calibrate logging equipment for measurements of density, sonic velocity, magnetic susceptibility, and electrical resistivity.

Jan 1, 1976

By H. M. Lavender

This paper describing the inclined cut-and-fill, and the semishrinkage methods of mining at the Campbell mine of the Calumet and Arizona Mining Co. at Warren, Ariz., is one of a series being prepared by the United States Bureau of fines on mining methods, practices and costs in the various mining districts in the United States. The major portion of the production from the Bisbee mines of the company is mined by these methods. The total average yearly production for the last two years has been 493,612 tons of 5 per cent copper ore. The average employment in the mining department eras 940 men. With the exception of a small tonnage mined for the high iron and sulphur content, the ore is direct-smelting and is mined for its copper con¬tent and associated gold and silver values.

Jan 1, 1930