Search Documents

By Richard A. Winters

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 34,000 acres of the 58,040-acre Little Jacks Creek Wilderness Study Area (ID-111-6) in order to evaluate the mineralized resources. The study area is located in Owyhee County, 10, about 21 miles southwest from Bruneau. No mining districts are in the study area, nor were any mines or claims recorded or found. The northern half of the area was covered by oil and gas lease applications; all were cancelled prior to 1985. No economic concentrations of minerals were found in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Little Jacks Creek study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By Gary E. Sherman

To aid the U.S. Army Corps of Engineers in their Resource Development Navigation Study, the U.S. Bureau of Mines (Bureau) examined the potential for mineral development near ten Alaska port sites. This report presents the results for the following four sites: Balboa Bay, Beluga, Lost River, and Point MacKenzie. There are 579 known deposits within the area considered for these ports. The majority of the deposits are located within a highway/railroad corridor examined for the Point MacKenzie port site. Based on the current level of knowledge, coal deposits near the Beluga and Point MacKenzie port sites are most likely to be developed in the near future. This conclusion is based on the fact that coal projects in these areas are actively being pursued for development. The mineral wealth surrounding the four port sites is substantial. Mine models were used to examine the potential for mining tin, gold, silver, copper, and molybdenum. The models were based on published reserve and grade data and therefore do not include proprietary company data which, if available, would likely change the analysis results. Of the models examined, the tin placer mine model developed for the Lost River port site proved to be closest to being economic.

Jan 1, 2011

By Larman J. Heath

Wellbore enlargement was tested using hydrazine hydrate in a gas-storage well in Ohio to increase the well productivity. The wellbore was to be enlarged by chemical disaggregation of the sandstone adjacent to the wellbore. Productivity immediately declined 49.1 percent and gradually declined to zero in 7 months. A down-hole camera survey showed a white-to-gray precipitate covering the entire wellbore surface. The precipitate was chemically analyzed and identified as mostly carbazic acid, a hydrazine derivative of carbonic acid. Formation of this precipitate was not anticipated; this viscous sub-stance caused the gradual loss in productivity of the well. The wellbore was not enlarged. Laboratory tests were run to determine what clay stabilization measures could be taken in sandstone cores to prevent clay swelling and particle migration caused by hydrazine hydrate. Normal clay stabilization methods did not prevent the virtually complete loss in permeability to hydrazine hydrate. Other laboratory tests using natural gas diluted with small amounts of carbon dioxide confirmed the ease with which carbazic acid could be formed in a hydrazine hydrate-saturated environment within and adjacent to the wellbore.

Jan 1, 1970

By R. L. de Beauchamp

A preliminary investigation was made of the extraction of chromium from ferrochromium by low-temperature chlorination in the 3400 to 5250 C range. The objective was to devise a method for separating chromium from iron in high-carbon ferrochromium produced from domestic chromite concentrates. The majority of iron was removed as a volatile chloride; chromium was contained in the residue as a nonvolatile chloride, which was separated from carbon and unattacked ferrochromium by dissolution. A small rotary chlorination apparatus was designed, built, and used for the chlorination tests, and samples of commercial-grade high-and low-carbon ferrochromiums were chlorinated for comparison of chlorination characteristics. Low-temperature chlorination of three types of ferrochromium resulted in the removal of 81.9 to 91.6 percent of the iron content as sublimed FeC13. Recovery of chromium in a leach solution of the reactor product varied from 82.4 to 93.1 percent.

Jan 1, 1968

By W. W. Roepke

The Bureau of Mines has developed an interactive computer program that enables mine operators and others to identify the effect of cut-ting system changes on relative dustiness at the face. The program, which simultaneously evaluates machine parameters, coal seam parame-ters, and operator-controllable parameters, was developed for use on any microcomputer using BASIC programming language. The program allows the user to change one or more of the cutting system parameters at a time to see how these changes affect relative dustiness. A complete program listing and flowchart are included along with operating in-structions and sample outputs. An example showing how to use the program is also included.

Jan 1, 1985

By G. H. Bennett

A field experiment was performed in a production unit of an operating copper room and pillar mine to compare the support capabilities provided by resin and mechanical roof bolts. Resin and mechanical roof bolts were alternately installed in eight intersections in a single entry. Rock mechanics instrumentation was installed to measure roof sag, bed separation, convergence, bolt pullout, torque, and strain. Bolt cost and installation time are included. Two analyses of the test were made. The analysis of the rock mechanics data showed there was no definite difference between the two bolting systems. From a broader analysis on a mine-wide basis it was concluded that resin bolts gave better support. A critical view of the experiment is given in the appendix.

Jan 1, 1974

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 22 jurisdictions of the Near East and South Asia. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes : First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; and third, analysis of laws applicable to natural gas, petroleum, and related materials. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of states or provinces, those areas are considered separately from the central government.

Jan 1, 1972

By H. F. Yancey

About 65 percent of the more than 400 million tons of coal produced annually in the United States is mechanically cleaned to remove the inorganic impurities before being sent to market. The impurities, principally shale and clay with some pyrite, average about 20 percent of the raw coal treated. Nearly 95 percent of the tonnage is treated by wet processes, in which water, suspensions of solids in water, or occasionally calcium chloride solutions are employed. Difference in density of coal and impurity is the basis of these processes. Of major importance in the separation is the competency of the impurities, that is, the resistance of the impurities to size disintegration in water. In general, the impurities are more resistant in geologically older coals or those in effect made older by metamorphism. If the impurities suffer reduction in particle size when immersed in water, the separation of organic from inorganic material becomes more difficult, Recently the Scientific Department of the National Goal Board (Great Britain) undertook fundamental research into the interaction of shale and water and also developed an empirical method of assessing shale breakdown or disintegration. 6

Jan 1, 1962

After a stagnant performance in 1982, gross national product (GNP), industrial production, and employment increased during 1983 in nearly all industrial nations, with the U.S. performance generally leading the uneven worldwide recovery. Real U.S. GNP increased 3.3 percent in 1983 (table I). Although investment in nonresidential structures declined, total nonresidential fixed investment in the United States was up 1.5 percent following a 1982 decrease. The increase in worldwide industrial activity and demand in 1983 put greater pressure on prices in many countries. Prices increased from less than 3 percent in the Federal Republic of Germany, Japan, the Nether-lands, and Switzerland to as much as 10 percent in nearly all the other Organization for Economic Cooperation and Development nations. The annual inflation rate in the United States was 4.3 percent (based on the GNP fixed-weight price index).

Jan 1, 1984

By Foster Fraas

One of the lithium minerals most widespread in the earth's surface is spodumene (Li2O-A1203-4Si02) a lithium aluminium silicate. For some time, deposits of this mineral were known to exist in the Black Rills of South Dakota, but it was only quite recently that Hess4/ pointed out the great magnitude of the low-grade e deposits it s in North Carolina. The theoretical lithia (Li20) content of spodumene is 8.04 percent. The only other minerals with such high lithia content are the phosphates, but these occur only in pockets and are not in extensive deposits5/. Actually, however, the lithia content in spodumene is never found to be this high, being nearly always below 7 percent for the pure mineral, and part of the lithia is apparently replaced by other alkalies.

Jan 1, 1937

By Annie G. Smelley

The Bureau of Mines is testing a dewatering technique for phosphatic clay waste that will recover a portion of the water lost using conventional waste disposal methods and produce solids suitable for land reclamation. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong, stable flocs that can be dewatered on a static screen followed by further dewatering on a rotary screen. In field tests conducted in northern Florida, clay wastes containing a nominal 2.5 pct solids have been consolidated to greater than 20 pct solids. The rate at which PEO-treated material continues to dewater in a mine cut also was monitored. Preliminary results indicate that PEO--treated material will dewater to 30 pct solids in 140 days. Pretreatment of phosphatic clay waste with lime and H202 was shown to improve the dewatering technique for problem clay wastes.

Jan 1, 1985

By C. E. Lapple

To improve mine health and safety conditions, there is need for a portable instrument that mine inspectors can use routinely for rapidly checking concentrations of dust in mine atmospheres. On October 23, 1969, Stanford Research Institute was authorized by the U.S. Bureau of Mines to conduct a study aimed at developing such an instrument under Contract No. H0100186. The results of that study are reported in Technical Report No. 1, "Development of Portable Instrument For Measuring Coal Mine Dust Concentration," August 1970. In that study it was demonstrated on bench-scale that a near-forward optical scattering device gives a linear correlation between mass concentration and optical readout over a range of 2 to 200 mg/m3 with excellent reproducibility. The same correlation was obtained for the Respirable* dust fraction of three different coal dusts within ± 10% and an extreme spread of ± 30%. Based on these results a prototype instrument was designed which was expected to meet all the necessary requirements of a portable instrument for mine use. Because of the excellent results obtained, a further study was authorized by the Bureau of Mines on May 10, 1971 under Contract No. H0111688. The prime objective of this study was to build, calibrate, and deliver to the Bureau of Mines two prototype instruments based on the design previously developed. The emphasis was to be on providing instruments which would meet certain minimum standards of size, weight, response time, sensitivity, ruggedness, reproducibility, permissibility, and cost (ultimate); optimization of the design was to be considered only insofar as it would not significantly delay the development. One instrument was to be delivered after initial calibration of both instruments with Coal Dust PGH. The second instrument was to be used for further calibration with a number of other coal and rock dusts and for assessing other relevant performance characteristics. This report summarizes all the results of this second study.

Jan 1, 1972

By C. B. Davison

One goal of the Bureau of Mines is to conserve the Nation's mineral resources by developing improved performance materials. Consistent with this goal, the Bureau conducted studies on the formation of undesirable cristobalite in seven different fire clays used as refractories. The studies employed scanning electron micrography, chemical and X-ray analyses, and pyrometric cone equivalent determinations to examine the sample clays and determine the effect of thermal history and stablilizing additives on the amount of cristobalite in various calcines. This research has indicated that as fire clay calcining temperatures increased from 1390° to 1,490° C there was a gradual decrease in the percent of cristobalite present in the calcines and a progressive development of mullite crystallization. No cristobalite was found in fire clays calcined above 1,550° C, but cristobalite reappeared when the calcines were reheated to temperatures between 1,400° and 1,500° C. The research also revealed that additions of lithium fluoride (LiF) prevented formation of cristobalite in fire clay calcines.

Jan 1, 1979

By John M. Devine

The severe corrosion of equipment that is caused by the presence of hydrogen sulphide in oil and gas has been described in detail by several authors.5 Such corrosion, termed "low-temperature hydrogen sulphide corrosion", presents a somewhat different problem from the "high-temperature hydrogen sulphide corrosion" that is encountered in refinery operation and

Jan 1, 1932

By M. J. Sheridan

"INTRODUCTION In December 1942, the-Bureau of Mines reported favorably on a proposal to grant Government assistance-in constructing an access road (consisting principally of a timber-pile bridge across the Rio Grande at Hot Springs, N. Mex.) to the property under lease to the United States Fluorspar Co. At that time the property was being developed actively, and there appeared to be no immediate-need for exploratory or metallurgical assistance by the Bureau of Mines.Because milling facilities were inadequate; the access-read project was eventually disapproved, but prior to disapproval the company had discontinued operations. In June 1943, exploration was resumed by the Humphreys Gold Corporation of Denver, which had subleased the property. Difficulty of access continued to interfere with exploratory progress. In July 1945, at the request of the lessee, the Bureau of Mines directed sampling, using company employees.At the completion of this sampling program, the Bureau of Mines concluded that the property was potentially a important source of fluorite but that further development for production appeared to depend largely on the establishment, by exploration, of adequate reserves. Because of the relatively easy position-of metallurgical-grade concentrate and ores, it also was deemed advisable to investigate the possibility of producing acid-grade concentrate from the ore, for which a demand was becoming evident. Accordingly, a program of trenching, diamond drilling, and metallurgical testing was undertaken by the Bureau. The results of its investigation are reported herein."

Feb 1, 1947

By G. W. Jones, R. E. Kennedy

"INTRODUCTION In the manufacture, storage, transportation, and use of combustible gases and vapors, explosion hazards, which at times may be present when air becomes mixed with the gases and vapors, become of primary importance. Such conditions are especially dangerous where large volumes of gaseous atmosphere are involved, because an explosion under such circumstances is capable of doing tremendous damage to both property and personnel.Because of its interest in safety in the mining and allied industries, the Federal Bureau of Mines has investigated, and published results dealing with, the explosibility of various types of combutible atmospheres. The explosion hazards of natural gases have received attention, and results giving the limits of inflammability and ignition temperatures in air have been determined and published. 4/ Other investigations have shown how explosions of natural gas-air mixtures may be prevented by the addition of nitrogen and carbon dioxide. 5/Because of the increased demand for crude oil for war purposes, the application of secondary-recovery methods of stimulating oil production have received considerable attention during the last few years. The process consists in the injection of natural gas into partly depleted oil wells to cause the oil in the sands to flow into producing wells and so increase the amount of recoverable oil. 6/"

Feb 1, 1945

By John H. Johnson

This report covers the third and final year of work conducted under U. S. Bureau of Mines Grant G0166027, "Monitoring of Mine Air Pollutants". The report discusses work performed in three areas. These are the White Pine Mine (WPM) Experimental Unit, diesel mine-vehicle tailpipe emissions monitoring, and mine ambient air concentration data analysis. The WPM experimental unit was used to study diesel exhaust stratification in an 80 foot long dead-end heading while loading ore with a Wagner ST-5D scoop train LHD. The MTU Mine Air Monitoring Laboratory (MAML) was used to gather temperature and CO2 concentration data at 10 locations. Three different ventilation conditions were compared. The data substantiate the presence of strong buoyant forces of the hot exhaust gases which result in temperature stratification in dead-end headings. The diesel mine-vehicle tailpipe emissions monitoring study involved laboratory measurements of diesel undiluted exhaust pollutant concentrations by the portable tailpipe emissions measurement apparatus (EMA) assembled for in-mine use. The results were compared with simultaneous measurements by standard laboratory exhaust monitoring instruments. These results indicate that accurate field source quality control measurements can be obtained for CO2, CO and NO but NO2 results were low for all engine conditions. The mine ambient air concentration data analysis study included analysis of diesel pollutant concentration data in the Orchard Valley Mine air and comparison of the results with data collected earlier in the White Pine and Brushy Creek mines. The analysis included preparation of lognormal frequency distributions and calculations of C02-based concentration ratios and correlations. In the three mines compared, pollutant concentrations are distributed quite similarly, and the concentrations appear to be controlled to present standards.

Jan 1, 1979

By Robert R. Perron

The U.S. Bureau of Mines is engaged in many diverse programs for improving mine safety. Of particular interest to the Bureau are new and improved means for minimizing the hazard of fire which can be initiated by prolonged low energy electrical faults on trolley line systems. When a high energy fault occurs on a trolley line, wherein the current exceeds the magnitude normally drawn by legitimate loads, such as locomotives, then the circuit breakers at close-by power rectifier sets trip. Tripping of the breakers not only protects the equipment at the rectifier sets, but also disconnects the energy source from the fault and thereby minimizes the fire risk. However, the fault current is frequently of a level substantially below that required to trip the overload breakers. When the fault is a substantial percentage of the set level of the breakers, the energy dissipated by the fault is frequently sufficient to clear the system by rapidly burning itself clear. Such a fault is often short-lived and does not present as serious a fire risk hazard as a prolonged, much lower energy fault, wherein the energy level is too low to clear the system. The breakdown of a trolley line insulator, in which there was a 20 or 30 ampere leak, would represent such a fault or illegitimate load and a substantial fire risk.

Jan 1, 1974

By R. J. Burgess

During World War II the shortage of ore revived interest in eastern iron deposits, among which -!2..c "Ile Massachusetts and Connecticut limonites. The Cheever mine, in the Richmond-Salisbury area of Massachusetts, was formerly a large producer of limonite ere. The Bureau of Mines investigated the lateral and downward extensions of the Cheever ore body, which was mined from about 1850 to 1892, by ap open cut 1,000 feet long and also by underground workings. even holes aggregating 1,723 feet, were drilled by the Bureau during the winter of 1943-44. They comprised three diamond-core drill holes, two churn-drill holes, and two rotary-drill holes. A geophysical survey of the Cheever mine area and adjoining ground was made in conjunction with the drilling program. Although this survey did not locate the limonite ore beds, the data were of considerable assistance in locating the limestone contact which forms the footwall of the ore beds. Drilling disclosed two beds of limonite with a heavy overburden of glacial till.

Jan 1, 1949

Determine the advantages and operational limitations of water-let-assisted cutting used with mining equipment. Approach The Bureau of Mines con-ducted a research study to evaluate water-Jet-assisted cutting both in the laboratory and in underground mines. Earlier research on water-jet-assist was limited to laboratory studies where bit speeds and penetration depths were very low and large cutting force reductions were reported. For the past years, research by the Bureau of Mines and others has been concerned with the application of water-jet-assisted cutting under more realistic mining conditions. Study Results Water-jet-assisted cutting employs a mechanical cut-ting bit combined with a moderate to high-pressure water jet directed just in front of the bit tip to assist in the cutting process. Recent Bureau findings show that the addition of the water jet to the cutting bit can improve cutting in harder materials, significantly reduce respirable dust and bit wear, and increase product size. Some of these findings are presented as follows.

Jan 1, 1987