Search Documents

By Kari Moen, John Rasmus Leinum, Jarle Hjelen, Terje Malvik

"Automatic identification and characterisation of mineral raw materials and beneficiated products are of major importance in mineral processing. However, minerals show great variety in their composition and physical and chemical properties. Industrial minerals may contain the same elements in about the same amount. In these cases backscatter electron imaging or chemical analysis are not sufficient to identify the minerals. Another problem arises when micro textures are not detectable in traditional imaging or the grain size is smaller than the X-ray spatial resolution.As a supplementary technique in these cases, application of crystallographic information by electron backscatter diffraction (EBSD) in the scanning electron microscope (SEM) may be a suitable method. By means of EBSD, diagnostic mineral information can be achieved if indexible patterns are provided.Until now EBSD has not been used frequently on geological samples for mineral and micro structure discrimination.The technique has been demonstrated on three Norwegian mineral raw materials and one Italian marble and shows that it has some advantages compared to traditional techniques."

Jan 1, 2003

By Cheng Xiang, Nan Ye, Xinyuan Ke, Yang. Jiakuan, Huabin Wang

Bayer red mud is a highly alkaline residue produced by the alumina industry through the Bayer process. Its disposal is a worldwide problem. The high alkali content and poor pozzolanic activity is aconstraint for its utilization on construction materials. In this study, the red mud was activated through an alkali-thermal method to improve its activity so that it can be utilized in geopolymerization. The red mud was mixed with different amounts of sodium hydroxide, and calcined under 800 °C to produce geopolymer precursors, and then mixed with water directly to prepare one-part geopolymer. X-ray diffraction was conducted to study the phase transformation of red mud and the mechanism of its geopolymerization. Nitrogen Isothermal Adsorption tests were conducted to analyze the pore structure of the geopolymer binders. The results show that calcinations with alkali would promote the Al in red mud transforming into glassy SiO2 to form the N-A-S phase which is soluble in water. When the red mud was calcined at 800 °C with a Na2O addition more than 10%, the dissolving of Si and Al from red mud was greatly improved. The thermal-alkali activated red mud with 10% Na2O obtaining a compressive strength of 9.77 MPa after it reacted with water and cured for 7 days at 20 °C and 95% RH. But the strength decreased as the curing time extended to 28 days. The reason is suggested to be that the polymerization of Al-O and Si-O is unstable due to the low Si/Al ratio of red mud. The alkali in the structure dissolves again into the pore water and corrupts the pore structure. Therefore, the thermal-alkali red mud should be combined with other reactive aluminosilicate materials such as granulated blast furnace slag to absorb the alkali released by the thermal-alkali red mud at the latter curing days.

Jan 1, 2014

By T. Inoue, K. Okaya

"Movement of mill charge in the centrifugal mill is essentially different from that in the vibration mill with circular path despite the apparently similar mode in the motion of mill body. As proved e.g. in [11], this results in substantial advantage regarding the comminution intensity of the centrifugal mill over the conventional vibration mill accounting approximately to one order of magnitude.Back in 1983, Bradley et al. presented a model of the centrifugal mill based on the kinetics of the mill charge by regarding it as a lumped mass. On the other hand, numerical modeling by ‘discrete element method (DEM)’ enabled us to observe the movement of each ball in the centrifugal mill with an extremely minute time intervals (Inoue et al., XX IMPC in 1997). The former approach rendered simple, even though approximate, expression of the mill behavior, while the latter method was advantageous in describing the behavior of the mill in terms of individual events taking place in the mill body, even though the result did not reduce to a simple expression. The characteristics of the centrifugal mill described by both these approaches proved to be in a degree of agreement. Thus, the kinetic approach was capable of presenting the overall view of the mill, while the DEM model was informative of the details that could not be depicted well enough by the simple math expressions."

Jan 1, 2003

By Ray Everson, Henry Kasaini

"We carried out adsorption experiments in chloride media to study the adsorption characteristics of Pd (II) anions on the surface of activated carbon. Throughout the experiments, we used commercial activated carbon pellets (0.8 Norit). The adsorption process was interpreted by using the ionisation and adsorption model. This implies that palladium anions were adsorbed physically on a protonated surface of activated carbon either as anionic complex species (PdCl4 -2) or aqua chloro-complex species [PdCl3(H2O)-] in acidic media. Furthermore, we established that adsorption of Pd (II) species was reversible at high chloride [Cl-1] concentration. The maximum adsorption capacity (Qsat) of Pd (II) anions averaged 27 mg/g. The Toth adsorption isotherms fairly predicted the equilibrium adsorption of Pd (II) species and the associated surface coverage.The effect of temperature and acid strength of the feed solution on the adsorption of Pd (II) ions were quantified. The adsorption kinetics was limited by external mass transfer since the effect of pore diffusion on the overall rate constant was negligibly small. A pseudo first-order kinetics model was used to describe the adsorption kinetics."

Jan 1, 2003

By Kym Runge, Wei Huang, Fengnian Shi, Christian Antonio

"This paper presents an emerging High Voltage Pulse (HVP) technology for ore pre-treatment. Unlike previous studies where HVP was utilized as a crusher to pulverize ore particles to micron size ranges for downstream processing, the researchers at the Julius Kruttschnitt Mineral Research Centre (JKMRC) use HVP to enhance ore processability. Application of relatively low levels of HVP energy to selectively break mineralized particles from barren rocks, followed by size-based screening separation enables the feed ore to be split into high grade and low grade products. During HVP treatment, cracks/micro-cracks are generated which results in pre-weakening of the treated ore particles, which ultimately results in energy savings in the downstream comminution processes. HVP treatment followed by conventional grinding also results in improved liberation of the valuable minerals in comparison to that achieved with traditional conventional comminution, subsequently improving downstream separation efficiencies. The three major improvements in ore processability through HVP pre-treatment have the potential to facilitate rejection of low grade ore prior to processing, increase production rates, reduce the energy required for comminution and improve flotation separation recoveries. This paper summarizes the major research outcomes of HVP pre-treatment demonstrated using ores from various mining operations conducted by the JKMRC. It also discusses the barriers that must be overcome before it can be adopted by industry with confidence in a continuous high tonnage rate application.INTRODUCTIONThe challenges of declining ore grades and increased plant throughput rates, resulting in higher energy consumption and operational costs, require the mining industry to adopt new technologies to make future ore treatment economically viable. Over the past 50 years, many researchers have engaged in investigating novel comminution techniques. Since Yutkin (1955) first demonstrated the potential to generate shock waves with pressures exceeding 103 MPa via electrical breakdown of water, several applications of electrohydraulic crushing by shock waves have been reported (Curley-Macauly, 1968). Interest in this technique was bolstered when Andres (1977) demonstrated that electrodynamic fragmentation results in superior liberation of mineral grains as compared with conventional grinding techniques. Despite mounting laboratory-scale evidence of the efficacy of electrodynamic fragmentation for mineral liberation, development of the technology for full-scale operation has stalled, primarily because the energy required to achieve desirable mineral liberation is approximately two to three times that of mechanical comminution, amounting to approximately 100 kWh/t for typical mineral ores (Andres et al., 2002)."

Jan 1, 2018

By Roberto C. G. Oliveira, Scott C. Brown, Brij M. Moudgil

The wettability or surface energy of particle surfaces dictates a number of multiphase ensemble interactions that have a significant impact in mineral processing. Dispersion, bulk powder handling and flotation behavior are just a few of the parameters that are largely due to the degree of hydrophillicity or hydrophobicity on particulate surfaces. Because of the inherent impact of surface wettability in nearly all industries, fields, and multi-phase interactions, a number of simple, precise and accurate techniques for accessing surface wettability or contact angle on macroscopic flat surfaces have been developed. However, these techniques cannot be directly applied to the particulate surfaces that are often in query. Though a number of techniques are available for accessing the wettability of particulate surfaces, these methods are either relative, application specific or prohibitively tedious. In this study, key features of existing techniques are combined to formulate an improved method to delineate particle wettability that is simple, versatile and capable of providing reproducible measurements in an industrial environment.

Jan 1, 2003

By A. Akcil, O. Celep, C. Erust, E. Y. Yazici1, H. Deveci1

"Recycling of WEEE has already gain prime importance from both environmental and economic point of view. For the recovery of metals from e-waste, many conventional physical, bio/hydrometallurgical and pyrometallurgical processes are proposed. Economic potential of e-waste is mainly driven by its precious metal content. Physical separation methods (e.g. electrostatic, magnetic, eddy current and gravity separation) exploit the differences in the physical properties of metals and non-metals. Physical separation methods are simple and economically sound but they suffer from metal losses and ineffectiveness at fine sizes. Hydrometallurgical processes are promising owing to their relatively low cost, reduced environmental impact, potential for high metal recoveries and suitability for small scale applications. Hydrometallurgical processes can be developed for selective extraction of base/precious metals using suitable reagent systems. Sulphate-based leaching with a suitable oxidant (e.g. H2O2, O2, Fe3+) is effective for copper and other base metals. After removal/recovery of base metals, precious metals can be easily extracted using various lixiviants including thiosulphate, thiourea, cyanide and chloride. However, further research is required to develop new, cost effective and environmentally friendly processes and/or refine existing ones for leaching and, in particular, downstream processes. INTRODUCTION Electrical and electronic equipments are indispensable to modern societies with numerous applications in the field of medicine, transport, communication, education, security and environmental protection. With technological developments and innovations, the replacement of old equipment leads to ever fast accumulation of waste materials such as waste electrical and electronic equipment (WEEE or e-waste). People are upgrading their mobile phones, computers, televisions, audio equipment and printers more frequently than ever before (Babu et al., 2007; Lee et al., 2007). With the rapid growth in technology today, the life span and utilisation period of most electronic and electrical equipment has been reduced considerably with concomitant generation of huge amounts of WEEE over the past several decades. According to statistics presented by Balde et al. (2015), total WEEE produced around the world was 41.8 million tonnes in 2014 and expected to rise to approximately 50 million tonnes by 2018. Kumar et al. (2017) estimated that annual growth rate for the WEEE stream is 3–5% (Singh et al., 2016). The aim of this paper is to provide an overview of physical separation and hydrometallurgical methods available for the treatment of WEEE."

Jan 1, 2018

The quality of iron ore fines in terms of high iron content and low levels of deleterious impurities such as Silica, Alumina, Sulphur and Phosphorous is a critical parameter, in sintering and subsequent iron and steel making processes. As the higher-grade ores become depleted, there will be a stronger focus on treating lower-grade haematite/goethite ores and developing suitable beneficiation techniques to reduce the levels of impurities. Innovative flow sheets, based on new and commercially available technologies, is required. These will be needed to include gravity concentration devices, which can handle coarse and fine feed sizes. In this paper, efforts made to reduce the silica and alumina content of a low grade iron ore fines (<1.0 mm size) sample from the Pilbara region in Western Australia are described. The feed sample, a goethite abundant lower grade iron ore fines, which was a plant reject assaying 48.66% Fe with 13.61% SiO2and 5.09% Al2O3 was investigated. To this end, an experimental campaign was undertaken, and beneficiation studies were conducted on the sample using a Floatex Density Separator (FDS), a gravity device which can be operated for size classification and/or relative density separation. The objective was to produce high-quality iron ore material suitable as sinter feed. An iron concentrate with a grade around 57.0% Fe (Calcined Fe of about 63.0%) was achieved while recovering around 67.0% of the feed weight. In addition, a rejection of substantial content of Silica (>75%) and Alumina (>66%) was achieved while securing >77% iron recovery. On the other hand, sharp classification efficiency with low values of imperfection around 0.20 was obtained. Consequently, the response of the lower grade iron ore sample to FDS application, has vast potential to reject deleterious impurities as a single stage separating beneficiation equipment. Remarkably, it was demonstrated, that a great amount of goethite, abundant in lower grade iron ore fines/plant rejects, which are currently being either stockpiled and/or dumped as waste, can be treated using FDS application and potentially can add a significant value to the iron ore mining industry by recovering additional iron ore fines. Keywords: deleterious impurities, beneficiation techniques, classification, relative density separation

Sep 1, 2012

By Katarina Theander, Robert J. Pugh

The generation of froth with a critical degree of stability and height is an important aspect of the froth flotation. In this paper we have studied the synergism and anti-synergism in frothing behaviour in a mixed flotation collector/frother mixture (a model fatty acid; sodium oleate and a model frother; nonionic (polyethyleneoxide alkyl C14E6). Values of the collector / frother molecular interaction parameters (the ß-parameters) were determined from the surface tension data using regular solution theory. The frothing characteristics of the system were evaluated using a glass column equipped with a series of conductivity electrodes, which enabled the water content of the froth to be determined. From these measurements, the dynamic frothability and static froth stability were determined. It was concluded that the synergism/anti-synergism in frothability was depended on the molecular composition of the surfactant system, the diffusion of monomer to the thin film interface and on the breakdown of the mixed nonionic/anionic micelles.

Jan 1, 2003

By Hoon Lee

Laboratory tests were conducted to evaluate the breakage characteristics of pyrophyllite in a laboratory ball mill. In grinding tests, the breakage characteristics were analyzed using the mathematical kinetic models based on the two breakage functions; the specific rate of breakage and the primary breakage distribution. Two samples having similar chemical composition show identical values in specific rate of breakage. In comparison, there are different values of primary breakage distribution for each sample. The size distributions of the product with various grinding time are well described by the parameters from non-linear searching.

Sep 1, 2012

By Luis Bergh, Iván Rojas, Juan Yianatos, Luis Vinnett

"At present, flotation rate characterization follows standard measurements to identify the overall flotation performance looking at the feed, tailings and concentrate in flotation cells or banks. This classical approach does not take into account the evolution of the true collection rate down the flotation banks explicitly. The potential for identifying the impact of the mineral characteristics (size and liberation) as well as the effect of different manipulated variables (reagents, froth depth, gas dispersion) on the true flotation process remains hindered. Top-of-froth (TOF) measurements, which consist of sampling the first layer on the froth surface, have been used to characterize the mineral collected by true flotation in rougher banks. The information provided by TOF samples allows evaluating the floatable mineral evolution (grade, particle size, liberation) down the bank. In this work, an indirect approach to estimate the flotation rate along rougher flotation banks is proposed. The new approach is based on the decreasing of collected mineral grades (on top of froth) and the feed characteristics. Flotation rates per liberation classes were used to reconstruct the TOF grades from the feed information. This approach requires a simple froth surface sampling, without constraints typically observed during mass balance surveys and uncertainties on the mineral recovery estimation. The proposed methodology was successfully applied at industrial scale using TOF measurements together with QEMSCAN information."

Jan 1, 2014

There are some problems in the beneficiation of fine-grained oxidized iron mineral such as high cost, severe sliming, poor results and low recovery due to the fine disseminated size of the mineral. Taking several representative types of finely-disseminated oxidized iron minerals as examples, the author analyzed the main difficulties in the beneficiation of such kind of ores and discussed the existing problems in grinding-classification, technological process, flotation reagents and separation equipments and the resolvents of these problems.

Jan 1, 2014

By Silvia Serranti, Giuseppe Bonifazi, Roberta Palmieri

The possibility to develop an efficient recovery and reuse of concrete materials from Demolition Waste (DW) represents one of the main targets applied to end-of-life constructions dismantling/recycling. The need to recycle end-of life concrete materials is strongly increasing in these last years for several reasons: i) the decrease of steady supplies of good quality natural aggregates, ii) the need to secure ample supplies of concrete aggregates to the construction industry and, finally, iii) the environmental constraints limiting the DW wastes disposal. The fulfilment of these goals produces several benefits, that is: i) a reduction of new resources consumption, ii) a strong reduction of the costs linked to transport and energy production, iii) the possibility to utilize materials, otherwise lost (e.g. land filled), iv) land preservation and, finally, v) the reduction of the environmental impact of new exploitation activities. A lot of efforts have been addressed to develop, set-up and apply innovative technologies to maximize DW conversion into useful secondary raw materials. The possibility to utilize efficient, reliable and low cost analytical tools to perform detection/control actions: i) to assess concrete characteristics, before demolition, and ii) to detect the presence of contaminants in coarse aggregates (e.g. bricks, gypsum, steel, glass, plastics, wood, etc.) represent the key issues to fulfil in order to develop innovative process/control actions/procedures inside the DW sector. In this paper a new technology, based on HyperSpectral Imaging (HSI) sensors is investigated to develop suitable and low cost strategies finalised to define and implement innovative smart detection engines for sorting and/or DW flow stream quality control, addressed to perform recovered materials and/or products certification. The proposed sensing architecture is fast, accurate, affordable and it can strongly contribute to bring down the economic threshold above which recycling is cost efficient.

Jan 1, 2014

By Mohammad Noaparast, Hamed Haghi

"In this research work, it was attempted to reduce the iron contents (Fe2O3) in relatively low grade silica sample which was obtained from Shenin silica mine, using magnetic separation. The prepared sample contained 93.75%SiO2, 0.44%Fe2O3, 2.78%Al2O3, and 0.08%TiO2 and the Fe2O3 had to be reduced to less than 0.08%. Mineralogical studies and XRD analysis indicated the presence of Hematite, Pyrite, and Goethite as the major iron impurity phases. Mineralogical studies of polished and thin sections demonstrated that the degree of freedom of silica is more than 80% in -300+212 ?m size fraction. After primary stages including crushing, milling, scrubbing and de-sliming, various methods such as low intensity magnetic separation (LIMS), high gradient magnetic separation (WHGMS) and dry high intensity magnetic separation (DHIMS) were applied to find out that which process would be appropriate for the elimination of iron impurities from this sample. Different experiments were carried out on the product of wet rod mill and scrubber. However the magnetic field intensity of WHGMS was increased down to 2Tesla, and there was not any acceptable result in reduction of Fe2O3 content lower than 0.08%. Thereafter the product of wet rod mill and scrubber were dried and reported to DHIMS. In these experiments, maximum magnetic field intensity was 1.4Tesla. In this case very significant results were achieved, and Fe2O3 content of final product were reduced to less than 0.05% which meets glass manufacturing standards."

Jan 1, 2014

By Mark Viduetsky, Dmitry Tropnikov, Victor Maltsev, Victor Sokolov, Alexander Purgin, Andrey Panshin, Alexander Bondarev, Pavel Kozlov, Igor Garifulin

"CFM pneumatic flotation machines were developed by the Institute of Materials Science and Metallurgy, UrFU, and designed to concentrate a wide range of ores and man-made materials. A key principle of work is pulp preparation for flotation owing to its saturation with finely dispersed air bubbles in ejectors. CFM plants, their advantages over domestic and foreign prototypes are described. CFM pneumatic machine commercialization resulted in: - machines demonstrated high floatation efficiency for concentration of rebellious pyrrhotite-bearing copper and zink by simultaneous floatation of copper and zinc minerals and depressing pyrrhotite. CFM- 1400M introduction allowed simplifying and optimizing the flow chart and increase extraction of copper - by 5.4%, zinc - by 9.5% and improve the quality of copper (3% Cu) and zinc (1.5% Zn) concentrates. - due to copper pyrite concentration by using CFM 1400M overall copper recovery was increased by 1.5 %, and the content of copper in concentrates - by1%. According to the results of pilot runs, the use of CFM flotation for zinc cakes concentration strongly intensifies the process of cleaning water-soluble metal compounds and, thereby, increases the efficiency of flotation concentration and subsequent milling. CFM machines showed higher specific capacity (three or four times higher) (both for feed material and froth product). Specifically, CFM froth product has higher content of useful elements (silver by 0.014 % abs. zinc by 0.31% abs.) and better extraction (silver by 6.08% abs., zinc by 0.31% abs., and sulfide sulfur by 13.7 %). Sulfide sulfur content of CFM product chamber as compared to mechanical flotation machines is two times lower (0.48 vs. 0.95 %)."

Jan 1, 2014

By Svetlana Krashenina, Nebojsa Petrovic, Oscar Lopez

"As easily mined gold deposits are becoming increasingly rare, gold producers are turning to the processing of ores with polymetallic and copper mineralization. These base metals can create metallurgical and waste handling/disposal challenges, which can render the project uneconomic. Base metals such as copper compete for the cyanide reagent used to extract gold, necessitating the need to increase cyanide volumes and consequently, cyanide consumption costs. Copper will also stabilize in tailings water as weak acid dissociable cyanide, a form that is both difficult and costly to destruct. SART (sulphidization-acidification-recycling-thickening) process technology can be applied to remove base metal interferences in gold projects. SART breaks the copper-cyanide complex and precipitates the copper as a saleable copper sulphide concentrate. With the copper removed, the cyanide can be regenerated as free cyanide for recycle to the gold recovery process. This improves cyanide utilization efficiency and mitigates copper presence in tailings. Additionally, copper recovery generates an incremental revenue source to further improve project economics. Engineering Dobersek GmbH together with BioteQ developed a SART and AVR testing program to recover cyanide and maximize operational efficiencies at a gold processing plant in Kazakhstan with high cyanide consumption in the leach circuit. Results from on-site testing demonstrated that up to 99.98% of copper can be removed and precipitated as copper sulphide and 60-90% of cyanide can be recovered from the AVR and recycled for leaching, reducing total overall cyanide use. This paper provides an overview of the testing methodology and results together with a discussion on the potential of SART to improve gold production operations to deliver both environmental and economic benefits."

Jan 1, 2014

By C. Dorfling

Experimental work was performed using a bench scale autoclave to evaluate the effects that leaching temperature, pressure, initial acid concentration, and the solid to liquid ratio have on the behaviour of base metals and platinum group metals in a high-pressure sulphuric acid oxygen leaching system. The concentrations of metals in the leach solution were measured over time at different leaching conditions. At the conditions investigated, the initial acid concentration had the largest influence on the copper leaching kinetics, while the leaching rates of the other precious metals (OPMs: rhodium, ruthenium, and iridium) were highly dependent on the leaching temperature. A set of chemical reactions that can be used to describe the leaching chemistry was proposed, and the associated reaction kinetics were quantified. As a first estimation, the rate expressions were considered first order, and the rate constants were determined using the method of least squares, considering the experimental and predicted concentrations obtained for the different leaching conditions. Of the OPM compounds, the sulphides showed the fastest dissolution rate, followed by OPM alloys, and finally the OPM oxides. During the initial leaching stages, base metals and OPMs competed for the available dissolved oxygen, with oxygen being preferentially used for copper leaching. Precipitation of OPMs during the initial leaching stages can be ascribed to copper and nickel dissolution according to exchange reactions between dissolved OPMs and copper present as digenite or nickel present as polydymite. Control of the autoclave residence time is of particular importance to enhance the selectivity of this leaching step, given the dependence of the PGM leaching rates on the extent of copper dissolution.

Sep 1, 2012

By S. Banisi, A. Ghasemi, S. Zare, F. Ghorbani, E. Nematollahi

"Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Working at the maximum operating capacity of comminution equipment plays a significant role in the efficiency of the circuit. Appropriate design of cone crusher feed box could result in the choked crushing which is known as a vital factor in achieving target performance. In this research, the non-uniform cone crusher feeding at the Sarcheshmeh copper complex was studied and appropriate measures were taken to solve the problem. The problem resulted in non-uniform and high wear rate of crusher liners and high fluctuations of power draw. In recent decades, the discrete element method (DEM) has been applied successfully to study the effect of different factors on the behavior of particles flow. In this work, various designs for feed box were tested using an in-house developed DEM software called KMPCDEM©. The best feed box design obtained from the simulations was selected, constructed and installed in of the cone crushers. The new feed box design resulted in more uniform feed distribution on the distributor plate of crusher indicated by a reduction of the standard deviation of power draw measurements from 13 to 3 kWh. The better control of the crusher, 49% increase in the crusher throughput and finer and narrower product size distribution were the main outcomes of the installation of the new feed box. Furthermore, the wear rate on mantle and liners of crusher not only decreased but it also became uniform.INTRODUCTION Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Reaching the maximum operating capacity in comminution equipment is a key sign of approaching the nominal productivity of the process. Due to the effect of crusher efficiency on the downstream circuit performance, optimization of the crushing circuits has received considerable attention (Herbst, & Potapov, 2004; Quist, & Evertsson, 2010; Li, Huiqi, McDowell, Glenn R, Lowndes and Ian, 2014; Cleary, Sinnott, Morrison, Cummins, & Delaney, 2017). Improving the performance of crushing circuits not only decreases the capital and operating costs but also increases the efficiency of downstream grinding circuits (Jacobson, Janssen, & Urbinatti, 2010). In cone crushers particles can be subjected to two different modes of compressive breakage; single particle breakage (free feeding) and inter-particle breakage (choked feeding). The maximum efficiency of the cone crusher directly depends on the type of feeding arrangement (Operation Manual, 1977). An appropriate feeding must lead to choked feeding the cone crusher. If the rate and method of feeding the crushers are correctly be executed, the maximum efficiency of the crushers could be available (Jacobson et al., 2010)."

Jan 1, 2018

By T. Neesse

In many cases, the use of hydrocyclone control is desirable for the stabilization of separation in the setting of changing feed conditions. Control concepts based on exact mathematical models are not satisfactory due to the complexity of the physical process. In this case, fuzzy control is a suitable solution. The data are primarily derived from an optical sensor that monitors the outside view of the free underflow stream. A throttling valve, serving as an actuator, is installed in the overflow pipe that regulates the volume split of the cyclone. Applications in closed circuit grinding and in separation plants for tunnel driving, fine sand dewatering, and classification of kaolin demonstrate the typical use of this development. Additionally, the technological characteristics of the cyclone may be improved by this control, which is mainly caused by the increased discharge capacity of the un-der flow nozzle. A further advantage is the option to operate at an optimal operation point. In many cases, this point is located at the transition spray/rope discharge. The improved operation characteristics present new options for extensive applications of fuzzy cyclone control.

Jan 1, 2014

By Lorenzo Reyes-Bozo, Ronaldo Herrera-Urbina, Pablo Higueras, Alex Godoy-Faúndez

"The copper mining industry in Chile and perhaps in other countries as well is faced with the challenge to implement the best practices in order to achieve a sustainable and more environment-friendly growth. Relationships between mining industry and society have been historically complex due to its environmental impacts. Whereas the ore grade has declined continuously, this has involved an intensive energy and water consumption thus increasing operational costs at different stages of the concentration process. In the case of copper sulphide ore concentration, froth flotation is the main technology used worldwide. The amount of the different chemical reagents used in flotation plants (i.e., collectors, depressants, frothers and modifiers) affects significantly production costs and has a negative effect on the environment as well. The objective of this research work was to evaluate the use of biosolids and their main components (i.e., glucose, proteins and humic substances) as more environment-friendly flotation collectors for chalcopyrite and molybdenite. For this purpose, microflotation tests were conducted in a modified Hallimond tube. In addition, FTIR and zeta potential experiments were performed to investigate the interaction of biosolids with these sulphide minerals. Biosolids and their main components may interact through physical and chemical ways due to different affinities with such sulphide minerals as chalcopyrite, pyrite and molybdenite, which are present in copper sulphide ores. In alkaline pHs, biosolids and their main components make the zeta potential of the sulphide minerals investigated more negative. These results may provide important information concerning the behavior of the main sulphide minerals in the concentration of copper sulphide ores at industrial scale, wherein mill processes could affect their surfaces properties. Therefore, biosolids and their main components may open an opportunity to be used in copper sulphide flotation plants to partially replace conventional reagents, which are more hazardous and less environment-friendly."

Jan 1, 2014