Search Documents

By Rodney J. Hundermark, Sharif Jahanshahi, Shouyi Sun

"The major platinum producers in South Africa make use of electric furnaces for the melting of PGM bearing nickel - copper concentrates. To gain better understanding of the furnace operation, research was conducted at CSIRO Minerals in Melbourne, Australia. One aspect of the research project was the investigation of the factors affecting the electrical conductivity of melter type slags.Electrical conduction in slags can occur through two mechanisms: ionic and electronic. There is good understanding of the ionic mechanism. In slags containing high levels of iron, the dominant mechanism is electronic. There is limited understanding of the electronic mechanism and one of the aims of the research was to investigate this mechanism further.Experimental work was carried out on Al2O3.CaO.FeOx.MgO.SiO2 slags similar in composition to the melter slags. Conductivity increased significantly with iron oxide content. Above 20wt% FeOx, electronic conduction was significant and the conductivity varied with the oxidation state of the slag. As the iron oxide content was increased further, the electronic mechanism became more dominant. The conductivity reached a maximum at around pO2 = 10-7 to 10-4 atm., although this value was dependent on the total iron oxide content and basicity of the slag."

Jan 1, 2003

By G. Bulut, Ü. Yenial

"Heavy metals contamination in aqueous systems can be found in a variety of industries, in particularly mining, metal processing, finishing and plating. Water containing more than 0.5 ppm heavy metal considered as a toxic due to harmful effects on health. The major techniques employed for heavy metal removal from industrial wastewaters include precipitation, reduction, ion-exchange, and adsorption. Adsorption is a heavy metal removal method for aqueous systems. As a common adsorbent, activated carbon has been used in treatment but it is ineffective on some elements. Thus, there has been a research for developing highly effective and selective adsorbents. In this study the adsorption of lead and arsenic ions on to coal waste and red mud waste was studied. The experimental parameters were determined as pH, equilibrium time and the initial concentrations, activation by heat treatment and the blend of adsorbents. According to their adsorption capabilities, red mud was found to adsorb lead and arsenic ion with high efficiency but coal waste did not adsorb arsenic ion. However the binary adsorptions of these ions were enhanced the adsorption efficiencies. In addition the blend of coal waste and red mud affected the adsorption efficiency. INTRODUCTION As a result of rapidly developing industry and excessive use of water resources, the need of clean water and wastewater management appear as a problem. Wastewater recycling activities and researches come to the fore for an effective use of wastewater. Recycling of wastewater, which contains heavy metals harmful to the environment and human, is a difficult process. Heavy metals are generally divided into three categories: toxic metals, precious metals, radionuclides. Wastewaters from various industries, containing heavy metals, are the main polluters of water and soil. Although their toxic structures, heavy metals are used extensively in industry as they have technological significance. Usually mining industry, metal industry and industrial organizations produce heavy metal containing wastewaters (Volesky 1990, Ting and Lawson 1991, Bishop 2002)."

Jan 1, 2018

By E. Barsky

The composition of multi-component materials is proved to be unambiguously determined by the composition uncertainty parameter (composition entropy). At the same time, every component, depending on its content, introduces a certain value into this parameter. Quality criterion of multi-component separation is determined by the total change of this parameter for all products obtained as a result of the separation process. This parameter can unambiguously estimate both multi-product separation and complicated schemes of modern beneficiation plants. It can be used to estimate binary mixtures separation, too. During the optimization of multi-product separation, another problem arises, which is not peculiar to binary mixtures. In this case, the total efficacy depends on the order of separation boundaries, as well. In the present paper, a specific example of initial product separation into seven products by six boundaries is investigated. It is clear that with respect to a single boundary, two products only can be obtained. In this case, the separation optimum is shown to correspond to the separation of boundary-class particles equally into both products. We have also established that from the point of view of entropy, the maximal possible separation efficacy corresponds to equiprobable composition of the initial mixture, i.e., the fine product quantity in the material to be separated is equal to that of the coarse product. Three groups of experiments were carried out. In the first group, the boundaries were consecutively specified from the finest to the coarsest one. In the second group, the boundaries were set vice-versa, i.e., consecutively from the coarsest to the finest one. In the third group, no sequence was observed. At every separation stage, a boundary was specified in such a way that the separated material composition was as close as possible to equiprobable one relative to this boundary. Total efficacy was different in all the three cases. In third group of experiments, its value is the highest, which confirms the advanced supposition. The obtained results are phenomenological, ? they can be applied to any processes of solid, liquid and gaseous materials separation.

Jan 1, 2014

By F. C. Araújo, T. Tavares, J. Leite

"This work presents the small-scale mining cluster of kaolin in Rio Grande do Norte (RN) and Paraiba (PB), both Brazilian states, including the following information: number of companies, process flowcharts, production numbers, mineralogical (XRD) and chemical (XRF) composition, granulometric distribution (screen and laser granulometer) and image analysis (SEM). Some social indicators in the region of the RN and PB States are presented in association with these data. The number of companies and their flowsheet were obtained through in situ visits and sample collection for technological characterization. The comparative study of the different flowsheets for kaolin production in the world was done using the databases and presenting the state of the art of kaolin processing. The results indicated that the mean feed typically contains 35-39% kaolin with quartz, muscovite and kaolinite as main mineralogical components and SiO2 (65.83%), Al2O3 (21.19%), K2O (3.9%), and Fe2O3 (0,63%) as main chemical constituents. The products of mineral processing are twofold, one between 74 µm and 37 µm, and the other smaller than 37 µm. The wastes of operation had major quantities of kaolin. The average Human Development Index (HDI) of the cluster region is approximately of 0.61, which shows an association between mineral processing plant and social indicators. The kaolin recovery, however, is between 30-55% for the three most common types of flowsheets that are currently used in the small kaolin mining cluster, indicating a need for technological improvement to achieve regional development. These data could be used incrementally to adapt the process plant currently used in the small-scale mining cluster of kaolin."

Jan 1, 2014

At times the phosphate industry, in Florida, encounters phosphate rock that gives lower than expected P2O5 recovery in the rougher plant section. The drop in recovery is typically 10% and as much as 30% or more. Variations in feed quality from day to day, shift to shift and even from drag-line to drag line, represent a challenge to the beneficiation plant operators and reagents? suppliers. Therefore, this characterization study has been initiated to identify the reasons for the differences in flotation behavior of such feeds. The study involves many samples to cover such variations. The characterization work includes: ? Mineralogical and chemical analysis; ? Size, shape, surface roughness and porosity analysis; ? Surface charge and surface contamination with other phases (minerals); ? Clay content and its relationship to phosphate and silica particles. The results correlated with flotation data and adsorption density measurements clearly establish the statistically significant variability in characteristic features that influence flotation response. This article discusses results from the above listed studies. On the basis of the obtained data, recommendations of practical approaches to overcome the problem of feed variability in phosphate flotation plants are delineated.

Jan 1, 2014

By Rong Fan, Roger Smart, Ning Xu

As part of an Australian Research Council project with Newmont and Newcrest mining companies studying the influence of clay minerals on rheology, hydrodynamics and flotation response, the cryo-SEM technique has been used to capture and image the clay (low crystallinity kaolinite Q38) aggregate structures in the flotation pulp immediately after collector and before frother addition. Samples were also collected from the earliest froth phase and the froth overflow corresponding to early and later concentrates. In this technique, a copper tube is filled with the sample during operation of the cell. The tube is immediately plunged into liquid nitrogen vitrifying the water phase before it can crystallise as ice thereby retaining the structures without volume or other physical change. After sublimation of the vitrified water surface, the aggregate structures are revealed and can be compared between pulp and froth phases from clays in different feeds and flotation conditions. The images from both low-clay ore and ore with clay content reveal various levels of aggregation as predominantly edge-edge connected aggregates similar to those found in our previous studies of high-clay tailings. For the samples from the ore with clay content, more extensive edge-edge clay strings are found in the early froth phase as compared to exiting froth overflow and the pulp phase with short edge-edge connected strings. It is suggested that the strings of clay particles result from edge-edge aggregation in the Plateau borders of the bubbles before breakage during sampling and the more extensive edge-edge aggregation in early froth phase is induced by crowding in the bubble borders. The clay strings collected into the overflow concentrate are almost all broken up compared with the Froth before drop-back. The implications for entrainment and entrapment mechanisms of gangue capture in froth will be discussed.

Jan 1, 2014

By Güven Önal, Zeki Dogan, Neset Acarkan

In this study, it was aimed to produce glass sand with less than 0.15% Fe2O3 for window glass manufacture and glass ware grade with less than 0.05% Fe2O3 from Yalõköy sand dunes having 0.48% Fe2O3. In order to reduce the iron content of the Yalõköy sand dune, magnetic separation, flotation, scrubbing, H2SO4 leaching and drying were used. The optimum iron removal was achieved by H2SO4 baking at 150oC and 8 kg/t acid consumption. In this way, sand concentrate was obtained with 0.04% Fe2O3 and sand recovery 95%.

Jan 1, 2003

By S. Castro, L. Uribe

Seawater can be considered as a particular process water with a high concentration of NaCl (about 0.5- 0.6 mole/L) and high concentration of hydrolyzing metal cations (mainly, Mg2+ and Ca2+ ions). Micro-flotation tests, induction time measurements, and zeta potential measurements have been used to investigate the effect of these ions on the natural floatability of molybdenite. The results demonstrate that molybdenite is strongly depressed in the alkaline pH range over which hydrolysis products of Mg2+ and Ca2+ ions are formed. At pH 10, colloidal magnesium hydroxide seems to be responsible for molybdenite depression in seawater and in Mg2+ solutions. This is also supported by the measurements of the effect of Mg2+ ions on the zeta potential of molybdenite. The mechanism of depression of molybdenite with Ca2+ ions is different, and depression takes place in the pH range were Ca(OH)+ complexes are formed, below the pH of precipitation of calcium hydroxide. Adsorption of the cationic hydroxy species and/or hetero-coagulation of the positive charged colloidal hydroxide on the negative charged molybdenite particles seem to be the main mechanisms involved.

Jan 1, 2014

By S. M. Bradshaw, V. Rocher, L Kabondo, B. Combrink, C. A. Snyders

Media losses are a significant contributor to the operational cost in a dense media separation (DMS) circuit. Of these losses, up to 80 wt% can occur on the drain and rinse vibrating screens. Although these screens are an integral part of any DMS circuit, surprisingly little work can be found in open literature regarding the effect of aperture configuration on the drain rates (draining water and medium). To establish the effect of slot aperture size, experiments were conducted on a 0.6 x 1.2 m vibrating screen with polyurethane (PU) panels at slurry densities between 1.6 – 2.8 kg/L, and volumetric flow rates of 19 – 25 m3/h for both ferrosilicon and magnetite. Results showed that an increase in the volumetric flow rate led to an increase in drainage rate, moisture content and medium carryover. Once an optimum volumetric flow rate was exceeded, a further increase in flow rate resulted in a decrease in drainage rate with a sharp increase in moisture and medium bypass to the oversize stream. An increase in ferrosilicon slurry density led to a decrease in drainage rate with an increase in moisture and medium bypass with each of these rates increasing as the slurry density increased. For magnetite, a gradual decrease in drainage rate was observed with increase in slurry density and volumetric flowrate beyond the screen optimum point. It was found that an increase in aperture size from 0.63 x 8.8 mm to 0.8 x 8.8 mm to 1.0 x 13 mm resulted in an increase in ferrosilicon drainage rate of between 1.3 - 1.8 m3/m2/h depending on the flow rate and slurry density with a reduction in moisture and medium carryover of between 1.0 – 1.2 % and 14.1 – 20.2 kg/t/m respectively. For magnetite, the drainage rate increased between 1.0 - 1.4 m3/m2/h as the slot width increased from 0.63 x 8.8 mm to 0.8 x 8.8 mm while an increase in slot length from 0.63 x 8.8 to 0.63 x 12 mm only resulted in an increase in drainage rate of 0.1 - 0.5 m3/m2/h.

Jan 1, 2018

By Ibrahim Alp, Ersin Yazici, Oktay Celep, Haci Deveci

Low extractions (<80%) in cyanide leaching impose the application of physical and chemical pre-treatment methods (e.g., ultra-fine grinding, roasting, alkaline leaching) prior to cyanide leaching to achieve acceptable recoveries. The effectiveness of the selected pre-treatment method is linked intimately with inherent mineralogical properties of ore. In this study, a refractory silver ore assaying 145 g/t Ag was subjected to various pretreatment tests in an attempt to eliminate its refractoriness. Direct cyanidation of the ground ore (d80: 65 µm) produced a low silver extraction of only 29.5% over 24 h indicating its high refractoriness. Previous studies have shown that silver occurs mainly as Sb/As containing sulfide minerals such as pyrargyrite (Ag3SbS3), tetrahedrite (Cu12Sb4S13) and proustite (Ag3AsS3), which do not respond well to cyanide leaching. Also, silver-containing minerals are closely associated with and/or encapsulated in other mineral phases that can restrict the contact of cyanide with silver. Therefore, alkaline leaching (using 3 M of Na2S, NaOH or KOH solution) and ultra-fine grinding as pre-treatment methods were tested to improve the extraction of silver. All the alkaline leaching tests were carried out for 3 h at800C. Neither NaOH nor KOH leaching produced the desired effect on the extraction of silver (i.e., ~30%). Even, a sharp decrease in the extraction of silver (i.e., 10%) was observed in Na2S leaching. On the other hand, ultra-fine grinding (UFG) (d80: 3 µm) substantially improved the extraction of silver in cyanide leaching (95% Ag at 24 h after UFG). It can be inferred from these findings that the refractoriness of the ore is essentially physical in character (i.e. the encapsulation of silver presumably in non-sulphide minerals such as barite and quartz).

Jan 1, 2014

By Luis Cáceres, Genny Leinenweber

"We have designed a planar perpendicular flow cell for electrochemical measurement of a mineral available as a fine powder. The working electrode consisting of mineral powder supported on a carbon paste surface as a 4 mm diameter disk, was concentrically positioned inside a vertical tubular reactor. The counter electrode was a 316L tube embedded in the body cell. The supportive media was a 1.2:1 mixture of candle wax and graphite powder respectively, which is a good electrical conductor. The concentrate electrode as a film attached on a carbon paste disk was prepared rubbing the surface carbon paste against dried powdered mineral. An Ag/AgCl 1 M KCl cell as a reference electrode was attached to the body cell by using a fast coupling fitting. A stable flow rate was achieved using a frequency inverter to drive the pump motor. The flow through the cell verified to be laminar due to the Reynolds number in the cell flow passage. Cyclic voltammetry from - 1200 a 600 mVSAgE were measured using a carbon paste with and without mineral attached to the surface. The main findings of this work were: a). Electrochemical measurement of mineral powder in contact with flowing samples was easily achieved using ground mineral. This is important where massive samples are not available. b). The voltammetric curve features of ground mineral coincided with reported data. c). The working electrode could be quickly replaced while maintaining very good reproducibility."

Jan 1, 2014

By I. Ngoma, Marijke Fagan, Susan Harrison, Rebecca Chiume

"Heap bioleaching is an unsaturated hydrometallurgical extraction process which is commonly applied to the recovery of copper from low grade sulfide ores as well as for preparatory treatment of gold ores. The leaching reactions occur in the liquid phase, catalysed by iron and/or sulfur oxidising micro-organisms. Contact of the mineral grains with the leaching solution is consequently essential for metal recovery. Additionally, the liquid is responsible for the transport of the liberated metal out of the heap under gravitation-driven flow. However, the highly inhomogeneous structure of the heaps coupled with low irrigation rates cause the flow to vary between being gravitationally and capillary dominated, resulting in non-uniform wetting of the ore. In this study a 132 kg agglomerated ore ‘slice’ is used to examine the effect of liquid distribution on microbial colonisation and mineral recovery in a long term bioleach (> 500 days) when irrigation from a single drip emitter source is employed. The novel setup enabled sample collection from ports positioned along the length and height of the ore bed, so that 2D maps of the degree of wetting and microbial colonisation could be generated at different times in the leach. Lateral movement of the liquid increased with bed depth; the majority of flow was below the irrigation point while the top corner of the bed that was not irrigated remained the driest region of the heap throughout the experiment duration. The lowest cell numbers were also recorded in the driest regions. Specifically, cell numbers in the top corner of the bed, 400mm from the irrigation point, remained at undetectable levels until the 283rd day measurement, in line with typical heap operation durations. This indicates that slow colonisation of the heap in the regions between irrigation points may be a significant issue in heap optimisation."

Jan 1, 2014

By O. Celep, H. Deveci, Ersin Y. Yazici, F. Ahlatci

"There are increasingly stricter environmental regulations imposed for use of cyanide leaching for the extraction of gold from ores. Alternative lixiviants to cyanide, preferably with low toxicity, have been extensively studied. Thiosulphate has emerged as one of the most suitable alternative leaching agent in place of cyanide due to its low toxicity and technical attributes e.g. fast leaching kinetics, high gold extractions from carbonaceous ores in particular. High solubility of most copper minerals in cyanide solutions results in low gold extractions due to excessively high consumption of cyanide. In contrast, low reactivity of copper minerals in thiosulphate solutions makes thiosulphate leaching potentially suitable alternative for treatment Cu-bearing gold ores. The extraction of gold/silver from a copper-bearing pyritic gold concentrate (62 g/t Au, 110 g/t Ag and 0.3% Cu) in thiosulphate solutions was investigated in this study. The concentrate is composed of predominantly quartz (25%) and pyrite (32.7%) as well as sphalerite (5.37%), galena (2.12%) and anglesite (1.13%). Other minor minerals are arsenopyrite, chalcopyrite, covellite and bournonite. Previous studies by the authors indicated that the concentrate did not respond well to cyanide leaching (i.e. 45-46% Au/Ag at 1 g/L NaCN). The effects of concentration of ammonia (0.2-1.5 M NH3), thiosulphate (0.1-0.75 M S2O3) and copper (0-20 mM CuSO4) on the extraction of gold and silver over 8 h. was investigated. Increasing the concentration of thiosulphate and ammonia substantially improved the rate and extent of gold leaching while high copper levels produced an adverse effect particularly at low concentration of thiosulphate (i.e. 0.1 M). Complete extraction of gold was achieved under suitable conditions. In contrast to gold, silver extractions remained consistently at low levels (i.e. 28%). These findings demonstrated that thiosulphate leaching could be used to achieve acceptable levels of gold extraction from the copper-bearing pyritic gold concentrate."

Jan 1, 2018

By Alok Tripathy

A simulation code called SIMJIG and the user interfaces have been developed using discrete element method (DEM) and the .NET platform respectively for the jigging process. DEM platform is used for tracking of particles in the jigging operation. DEM uses the net force balance on the particles to track the trajectory of the particle. Simulation results are compared with experimental results obtained by jigging of low grade iron ore lumps. Two different iron ore samples one from Chatishgarh and one from Odisha were used for the experimental studies. The Alljig? stratification test rig meant for batch laboratory experimental studies has been used in the present work. The behavior of different sizes of material on jigging has been examined. Later, the particle size behavior during jigging at different layers of the jig bed has been studied. Further stratification profile across the jig bed has also been studied. It was observed that simulation results are matching quite nicely with the experimental results. The SIMJIG simulator developed in the present study could be used for predicting the performance of the jigging operation effectively. Keywords: DEM, gravity concentration, jigging, iron ore, simulation

Sep 1, 2012

The traditional technological flow sheets for processing of ferrous quartzite (magnetite ores) al-low production of the iron concentrates with Fe content of 65%~68 % and recovery level about 55 %. The losses of iron with the tails of wet magnetic separation are related to hematite and quartz-magnetite particles, which are not extracted under low magnetic field employed. This work presents the results of the application of reverse cationic flotation for production of hematite concentrates with weak silica content from the tailings of wet magnetic separation of mag-netite. Fine particle size, complex mineralogy and presence of locked particles determine the impos-sibility of direct production of hematite concentrate by flotation or magnetic separation. The gravity concentration allows obtaining of iron concentrate from the well-prepared feed (size fraction -53+20 µm) but with very low recovery. Thus, hematite concentrates with weak silica content and satisfactory iron recovery were obtained by reverse cationic flotation, when it was fed with iron pre-concentrate produced by high gradient magnetic separation. The best flotation results were obtained by the use of formulations based on amines of different molecular structure that modulate the structure of adsorption layer, and favour a shifting of hydro-philic-hydrophobic balance on the surface of silicates with adsorbed starch and their preferential transfer into the froth product.

Jan 1, 2014

By Y. H. Wang

Micro-flotation tests of spodumene, beryl, quartz and feldspar have been carried out by using CaCl2 and FeCl3 as modifiers and a blending collector of oleic acid and hydroximic acid. CaCl2 shows efficient activation for spodumene when pH is above 11.5, and FeCl3 exhibits a markedly activation and good selectivity for spodumene in the range of pH 4 to 10. The main species of CaCl2 are CaOH+ and Ca(OH)2 when pH is above 11.5, and the main species of FeCl3?6H2O are Fe(OH)+2 and Fe(OH)3 during the pH range of 4 to 10. A selective flotation of spodumene and beryl from pegmatic ore had also been completed while using FeCl3?6H2O as activator and the blending collector. A bulk concentrate containing 1.087% BeO and 4.70% Li2O has also been obtained in the flotation of spodumene and beryl from pegmatic ore assaying 0.097% BeO and 0.45% Li2O, and the recoveries of BeO and Li2O in concentrate are 74.38% and 69.50% respectively.

Jan 1, 2014

The value creation with kaolin clays depends on removing the colored impurities which manifests in to higher brightnessone of the most sought after properties on applications such as paper coating, paint and others. The processes for removing impurities include magnetic separation, froth flotation and selective flocculation. While the flotation and selective flocculation processes exploit the physico-chemical differences between the surface properties, the magnetic separation uses the bulk magnetic susceptibility differences between the diamagnetic clay and ferro- and para-magnetic nature of the impurities. The major advantage with magnetic separation remains high yield and no or low reagent usage. However, the magnetic separation technology suffers from low separation efficacy when finer colored impurities (<1 µm) are encountered in the feed. Use of stronger magnetic intensities during magnetic separation showed limited success; nonetheless the adverse effect due to finer size range remains a dominant effect even at 5 Tesla magnetic field. Furthermore, the presence of diamagnetic colored impurities irrespective of their sizes can not be removed. Cytec Industries has recently developed a ?bolt-on? chemical enhancement technology for magnetic separation that essentially embraces the best product performance attributes of flotation and selective flocculation while keeping the chemical usage to a minimum level and using the readily available magnetic separation equipment. The paper will outline the technology and illustrate optimization work at pilot plant magnet on a wide variety of crude accommodating the process needs and plant limitations. The major advantages of chemical enhancement technology to magnetic separation include: 1) simple extension to existing magnetic separation technology, 2) ability to produce comparable product in quality with cost effectiveness compared to flotation and selective flocculation, 3) removal of impurity minerals over wide size range, 4) removing non-magnetic impurities, 5) providing robust process with high process yield and 6) operation-friendly nature. Furthermore, chemical enhancement technology for magnetic separation has also emerged as a platform for re-moving impurities at low levels in other mineral systems as well.

Jan 1, 2014

By A. Boehm

Mineral selective flash roasting (Steiner process) in oxidizing atmosphere was tested successfully for the efficient low intensity magnetic separation of siderite from ankerite and other gangue minerals within the ore of the Steirische Erzberg, Austria. The calcium, magnesium and manganese containing siderite turns selectively into a ferromagnetic oxide phase while ankerite remains paramagnetic. The expulsion of CO2 increases the volume specific surface depending on the selected temperature. Unlike pure iron oxides absorbing SO2 below 530°C, the calcined siderite (enriched in the magnetic product of the Steiner process) acts as a sorbent for SO2 between 500 and 820°C. The effect was studied by thermogravimetric analysis and particle bed tests complemented with neutron thermo diffractometry (D20/ ILL). The energy input was simulated with the help of a tube furnace. The composition of the artificial combustion gas permeating the bed was close to that measured in pilot scale tests (6 % CO2, 12 % O2, 700 vpm SO2). The evaluation of data relating the SO2 variation in the off gas monitored by electrochemical cells to the actual phase composition revealed an intermediate ferrite phase as absorber. During the rapid decomposition in oxidizing atmosphere starting at 500°C the occurring siderite alters to a (CaO, MgO, MnO)Fe2O3 ferrite as an intermediate phase accompanied with sudden SO2 absorption. SO2 disintegrates the ferrite structure forming MgSO4 and MnSO4, taking Fe2O3 as a catalyst. Ankerite (enriched in the non magnetics of the Steiner process) starts to absorb at temperatures above 1000°C forming gypsum. The findings support the SO2 controlled operation of the Steiner process by ?autodesulfurisation?. It explains aspects of the SO2 implementation reactions within off gas recycling in Austrian sinterstrands. Keywords: magnetising flash roasting, neutron thermo diffractometry, SO2 absorption, siderite, ankerite

Sep 1, 2012

By Robert van Hille, Alison Lewis

The precipitation of a selection of metals from both a synthetic and an actual metal-rich effluent was investigated. The experimental aspects of this study were carried out in a two-stage process consisting of a pre-treatment clarifier and a fluidised bed (pellet) reactor. Each unit operation in the two-stage process was investigated separately. The pre-treatment clarification stage at pH ˜ 5 resulted in a 99.9% removal of iron and 97.3% removal of aluminium. The pellet reactor was used to precipitate nickel as nickel carbonate from a pure stream and a removal efficiency of 99.6% was achieved. The high local supersaturation at the reagent inlet points caused the formation of a large amount of fines, but these agglomerated onto the pellets up the length of the bed. For copper precipitated as copper sulphide from a pure stream, a maximum removal efficiency of 92% was achieved. The high local supersaturation at the reagent inlets also caused the formation of a large amount of fines, but the extremely sparingly soluble nature of copper sulphide meant that the fines were not agglomerated up the length of the bed. For removal of cobalt as cobalt carbonate from an actual stream, a stable cobalt removal of only 60% was achieved. This was found to be due to the presence of magnesium, which reduced the cobalt precipitation efficiency through the formation of the magnesium bicarbonate ion.

Jan 1, 2003

By Jacqueline Satur, Yoshiaki Kon, Buenaventurada Calabia, Xiao Sheng Yang, Arvo Naumanen, Kenzo Sanematsu, Sayaka Morita, Tetsuichi Takagi

Granite ores are composed of silicate minerals and a variety of valuable REE (rare earth elements)-bearing minerals, however the processing technique to recover these valuable minerals is not yet developed. In this study, the recovery of REE-bearing minerals by dry magnetic separation and wet high intensity magnetic separation (WHIMS)-settling from surface sample and from drill core sample, respectively, of a granitic REE-Zr-Nb ore deposit was investigated. The two samples have different mineralogy however in both samples, light REE are commonly contained in REE carbonate minerals while Y and heavy REE are commonly contained in zirconium silicate minerals and pyrochlore. The liberation size of the REE-bearing minerals in the two samples ranges from 10-250 ?m. Previous flotation testwork conducted on the drill core sample reported high recoveries of La2O3 (88%) and Ce2O3 (88%) but low recoveries of Y2O3 (42%), ZrO2 (17%), and Nb2O5 (29%). The objective of this study was to obtain higher recoveries of Y2O3, ZrO2, and Nb2O5 by dry magnetic separation and WHIMS-settling. Both processes implemented the application of a low magnetic intensity to initially separate the ferromagnetic minerals then a high magnetic intensity to recover the REE-bearing minerals. The results showed higher recoveries of Y2O3, ZrO2, and Nb2O5 by dry magnetic separation and WHIMS-settling indicating the potential of magnetic separation and gravity separation in recovering the heavy REE-bearing minerals. WHIMS-settling is more recommendable than dry magnetic separation because of its applicability in treating a wider range of particle size. In the WHIMS-settling, the light REE, Y, and Zr minerals were recovered mainly by applying four stages at high magnetic intensity of 21,500 gauss while the weakly magnetic pyrochlore was recovered mainly by decantation of the nonmagnetic slurry after a short settling time of 0.25 to 0.50 h. (MAX.300 words)

Jan 1, 2014