Search Documents

By Glasswell K. Nkonde, Fredrick Chileshe, Steven Simukanga

Improving food security by increasing crop output is a primary objective for most countries in the sub- Saharan region. Most soils in the region are deficient in phosphorus an important nutrient after nitrogen in plant growth. Phosphates are therefore used together with nitrogen and potassium based fertilizers in improving crop production. Zambia like many other countries in the sub-Saharan region imports phosphate fertilizers for use by its farmers. However, indigenous phosphate deposits of igneous origin exist in Zambia of which the main ones are Chilembwe in Petauke district, Mumbwa sugarloaf in Mumbwa district, and Nkombwa Hill in Isoka district. If commercially exploited, these deposits could become a ready source of inexpensive phosphate for the local farming communities in the country. Previous research has shown that partially acidulated phosphate rock (PAPR) produced using Chilembwe phosphate rock is just as agronomically effective as the imported superphosphate fertilizers on food crops in most of the Zambian soils. PAPR is produced by reacting finely ground phosphate rock with only a fraction (usually 50%) of the stoichiometric quantity of the sulphuric acid required to fully convert the apatite in the rock to monocalcium phosphate thus making the process cheaper in terms of acid consumption than the poduction of single superphosphate where the apatite in the rock has to be fully converted to monocalcium phophate. The factors that affect the percentage of available P2O5 in the PAPR produced include particle size of phosphate rock, degree of acidulation, concentration of acid, process temperature profile, residence time and drying temperature. These factors were studied in a 25kg/hr PAPR pilot-plant in the School of Mines at the University of Zambia using Chilembwe phosphate rock. The PAPR pilot-plant consisted of a rotary drum granulator as the main reactor, a rotary drum dryer and a triple deck vibrating screen. Ground phosphate rock was reacted with sulphuric acid and water in the granulator to form a granular product which entered the drier. The dry product was screened into three size fractions. The 1 – 4 mm size fraction was the final product whilst the –1mm size fraction was recycled. The +4mm size fraction was sent to a crusher while the crushed PAPR was sent back to the screens.

Jan 1, 2003

By P. K. N. Raghavan

Bauxite is the principal source for the production of aluminum metal which has gained tremendous importance over the years due to its versatility as a metal capable of substituting almost all of the non-ferrous metals, non metals like wood, plastics, fibre glass, etc. and even steel in many applications. 90% of the high purity alumina needed for the production of this wonder metal in the world comes from bauxite. Even though alternate methods have been developed to produce alumina from non bauxite sources, owing to the high capital and operating costs involved, Bayer process still retains the superiority among all the methods by virtue of its simplicity and favourable economics. Bauxite continues to be the perfect ore for alumina production and its remarkable utilization makes it the most important non-ferrous ore. Most of the Alumina Refineries in the world process different types of bauxite and that too from varied sources. The technology employed in the Alumina Refineries depends on the Bauxite processed, with an ultimate view to produce alumina of required quality in the most efficient manner. Bureau of Indian Standards (BIS) and Indian Bureau of Mines (IBM) had from time to time put forward bauxite specifications for metallurgical and other applications. However, these are found no fully based on alumina technology, present developments and availability of different types of bauxite in the country. The aim of this paper is to provide scheme of metallurgical grading of Indian Bauxite based on the background of alumina processing technologies and availability of various types of bauxite in the country. Efforts are made here to evaluate beneficiation techniques for central Indian Bauxite from the point of view of alumina production. Keywords: bauxite beneficiation, digestion, alumina, gibbsite, bohemite, diaspore

Sep 1, 2012

By John Starkey

"The development of the SAG Power Index (SPI) Test in Canada has created a new and accurate way to measure ore hardness in a SAG environment. Coupled with the standard Bond Ball Mill Work Index Test it is now possible to determine from these two relatively inexpensive laboratory tests, the amount of energy required to grind an ore from the primary crushed size to the desired liberation size. By testing multiple samples to discover where the hard and soft ore zones are located, the representative hardness distribution for the ore body can be determined and grinding equipment selected that is capable to meet production targets for all mining areas of the deposit.Previously, it was deemed prudent to select up to 50 t samples of ore for Semi Autogenous Grinding (SAG) pilot plant tests and a second 5 t sample for metallurgical pilot plant work. The methods outlined in this paper show how the 50 t sample is no longer required for SAG design because it is better to measure the representative hardness distribution of the ore body than the hardness of a “chosen” representative sample. This is demonstrated to be true by the fact that the lower horizons of an ore zone cannot initially be accessed to recover 150mm pieces, and the bulk samples taken, rarely represent the desired design hardness of the ore. Median hardness will not yield a good result in most cases and a clear understanding of the location and extent of the hardest zones is imperative to achieve a truly successful grinding circuit design.This paper discusses two plants (Kubaka and Agnico Eagle) that have been designed using SPI and Bond with no pilot plant test backup. Both have been very successful in that they can grind design tonnage on the hardest ores in the mine. This guarantees that the mine’s profitability is protected in any mining sequence. It also allows the extra power to be converted to higher throughput on softer ores if additional cash flow is needed. The advantages from the owner’s point of view are dramatic. This procedure will be attractive as well when considering the costs for test work, and the samples for testing. Existing diamond drill core is normally used and this allows the inclusion of data from the deepest regions of the mine. In addition, it is also clear that the decision to use a crusher can now be made at the design stage of a project based on measured parameters and the estimated capital costs of alternative designs."

Jan 1, 2003

By Zoran M. Stevic, Mirjana M. Rajcic-Vujasinovic, Zvonimir D. Stankovic

"Covellite is one of the most important copper sulfide minerals. Its behavior during the anodic polarization, as well as its rest potential in various solutions are of importance for flotation processes and also define the mechanism of electrochemical extraction of copper from sulfide minerals.Measurements of the rest potential have been performed in water solutions in presence of different cations and anions. The existence of the Nernst type dependence of the rest potential on the activity of some of the investigated ions was established. The biggest influence on the rest potential of covellite exhibits the change of activities of the ions forming the crystal lattice of investigated mineral, i.e. Cu(II) and S(II). The dependence of the rest potential of covellite on logarithm of Cu(II) activity has a shape of a strait line with a positive slope of 60 mV, while when concentration of S(II) anions increases ten times, the rest potential of covellite decreases about 120 mV. The first dependence was established in acid medium, while the second was registered in alkali one.Different electrochemical techniques have been used for the investigation of the behavior of covellite during anodic polarization. In the basis of all these measurements is a three electrode system consisted of: 1) working electrode made of the sample of natural covellite from the Bor mine (Eastern Serbia, Yugoslavia); 2) reference electrode (saturated calomel electrode) and 3) counter electrode (flat platinum). Electrolyte solutions used in these investigations are of the same kind as those used in the rest potential measurements. Sulfate and chloride solutions, as well as the mixed sulfate/chloride solutions, are the most perspective from the application point of view.Cyclic voltammetry has been the first used method that confirmed the formation of passive layer on the electrode surface during anodic polarization. Elementary data about the reaction mechanism have been obtained too. More detailed data needed for more precise conclusions about the mechanism and rate of the anodic process on covellite have been obtained by galvanostatic method. It was established that the essential difference exists between the reaction mechanism in sulfate and chloride solutions. Also, the difference is exhibited in the nature of reaction product directly connected with the passivation of the electrode surface. Chronopotentiometric investigations have been performed in sulfate, nitrate, chloride perchlorate and mixed sulfate/chloride solutions applying different current densities. The shape of obtained curves indicate if there was a surface passivation and how intensive it was."

Jan 1, 2003

By Rodrigo Carvalho, Marcelo Tavares

"The accurate prediction of the outcomes in SAG grinding has been a great challenge to researchers and process operators. The use of Discrete Element Methods for modelling charge motion in tumbling mills allowed extraction of not only visual data, such as the position of the charge, but also the energy transfer in terms of the energy dissipated in the collisions. One of the advantages of DEM technique is its scalability to different mill sizes and some operational conditions such as speed and mill filling. Recently the Authors proposed the coupling between DEM outputs and modified Population Balance Models that with proper dedicated ore characterization tests allows the prediction of the outcomes of an energy transfer example. This modelling framework is called the Multi-scale Mechanistic Modelling. This paper shows the application of the Multi-scale Mechanistic Model to a set of pilot plant tests ran at different operational conditions. The prediction of the grinding outcomes and even the stabilization of the charge was achieved by the use of the Multi-scale Mechanistic Modelling framework. This approach has a great potential to become a powerful tool to design and optimize AG and SAG mills."

Jan 1, 2014

By Fernando Concha

"Thickening development and innovation in the 20th Century occurred in two decades periods. From 1900 to 1920, Dorr invented the continuous thickener and the first method of thickener design was proposed by Coe & Clevenger. From 1920 to 1940, the operating variables of continuous thickening were discovered by Comings at the University of Illinois. From 1940 to 1960, the first theory of sedimentation was proposed by Kynch and several authors, Talmage and Fitch, Ysioka and Hasset used this theory to develop new thickener design methods. From 1960 to 1980 Shannon and Tory demonstrated that this theory applied exactly for the sedimentation for small rigid spheres in water and Scott showed that it is not valid for flocculated suspensions. From 1970 to 1990 the phenomenological theory of thickening was developed based on the theory of mixtures. Papers by Kos, Bascur, Thacker and Lavelle, Concha and Bascur, Concha and Barrientos, Auzeris, Buscal and White, Landman, White and Buscal show the application of this theory to thickening and Adorjan presented the first thickener design method based on this theory. In 1980s the mathematical analysis and solutions of Kynch’s model for batch and continuous thickeners was obtained by Bustos. The new Century brought solution to the phenomenological thickening model which was applied to thickener design, simulation and control. The method of thickener parameter determination was improved by designing new laboratory and on-line instruments and advanced control strategies was designed and validated in plants. Structural thickener design produced improved feedwells and feed dilution mechanism, stronger raking mechanism and different thickener shapes according to new ambient requirements, such as high rate thickener and paste thickeners that increase the water recovery. New challenges include better flocculation and advanced control strategies."

Jan 1, 2014

By A. V. Bauman

"Important for thickening processes is the ability of slurries to form under certain conditions aggregation and sedimentation stable systems. Substantial part of difficult to sediment solid particles in such systems may be in colloidal state. The technique to study the sedimentation and aggregative stability of the slurry developed by the author with co-authors makes possible to define kinetics of changes in the aggregative stability of the system with solid phase varying concentration in it and produce data on sedimentation stability of the system in preliminary investigation of the thickening process. Research of aggregative and sedimentation stability of the slurry complement standard methods of laboratory studies to prevent errors in development of water-slime thickening balance and water circulation to design new and upgrade existing processing plants. Statistical analysis of process audits of more than one hundred upgraded and newly commissioned processing plants carried out in recent fifteen years showed that more than two-thirds of problems arising in commissioning the processing plants are associated with misdesign and errors in thickening and water circulation system. Among the main reasons of process design failures are: non-conformity of actual characteristics of the raw material to design characteristics, low quality of preliminary studies at the stage of sedimentation process simulation, design failures, wrongly selected equipment for the thickening and water circulations systems. As of today a number of problems associated with laboratory studies of sedimentation process, first of all, with interpretation of precipitation curves produced at the stage of laboratory refinement of the thickening process have been pinpointed. (Bauman A.V. Outstanding issues in design of thickening and water circulation diagrams in processing plants // Ore processing. 2016. ?3 P. 58-62) ?????? ?.?. ?????????? ??????? ?????????????? ???? ???????? ? ??????????? ?????????????? ??????. // ?????????? ???. 2016. ?3. ?. 58-62))"

Jan 1, 2018

By Janusz S. Laskowski

It is customary to assume that wettability plays an important role in coal flotation, and it is well established that while hydrophobic metallurgical coals float easily, low-rank less hydrophobic coals are difficult to float. However, coal surface wettability plays a dominant role in many coal preparation unit operations. As it will be discussed in this paper, it affects coal-dewatering, selection of flocculants, fine coal pelletization and briquetting, and even coal handleability.

Sep 1, 2012

By M. Amani, A. Akbarinasab, M. Bazmandeh

The fourth iron ore production plant at Golgohar mining and industrial company consists a ball mill and wet medium intensity magnetic separators (3500 Guss). The ball mill product applies directly into MIMS and the MIMS concentrate directly transfers to the low intensity magnet separators (LIMS). The thickener is used for dewatering of MIMS and LIMS tailings. By sampling from streams of ball mill and separators, it was defined that the grade and iron recovery were 60% and 80% respectively while they would be 66% and 90% respectively based on the designing documentation. The average of P80 in the ball mill was 342 micron in a month that is coarser than optimized value. This problem was related to unsuitable operation of grinding. For optimization of grinding efficiency, the amount of charge volume was investigated as a variable. The measurements illustrated 32% charge volume. For increasing grinding efficiency, the charge volume was increased 1% and 1.6% in two stages. The results showed ball mill power draw average reached from 3650 kw to 4120 kw and the average P80 reached to 329 micron. All of parameters calculated about 35 day before and after change. Average of Ball mill feed iron ore grade before and after change was 49.24% and 50.32% respectively. This change caused an increase in efficiency of MIMS, where the enrichment ratio and concentrate grade increased 2% and 1.9% respectively. For increasing the iron grade of the MIMS concentrate; the orifice of the tail flow exit pipe changed from 4 inch to 6 inch and the concentrate grade increased 2%.

Jan 1, 2014

By V. Yu. Ivanov, A. I. Yuryev, L. S. Lesnikova, M. S. Datsiev

"The Talnakh Concentrator was put into operation in 1981 using a direct selective process to produce copper, nickel and pyrrhotite concentrates.In 2001, a novel selective-bulk-selective (SBS) technology for the concentration of massive sulfide ore was implemented, that allowed to increase the valuable components recovery into target concentrates with feedstock grinding coarser than before. In 2003-2005, the process upgrading included the differentiated processing of nickelpyrrhotite products recovered at the different concentration stages and made it possible to significantly enhance the contrast of the pentlandite and pyrrhotite flotation properties and to simultaneously increase separation of polymineral intergrowths.The next stage of the PD concentration complex development is the Project ""Talnakh Concentrator Reconstruction and Technical Upgrading"" to raise its capacity by half. The project has three Phases.• Phase 1. Pilot startup was carried out in January 2015 following the installation of new OK-100 TC flotation machines, manufactured by Outotec.• Phase 2. The introduction of a new technology developed by the Polar Division specialists launched in mid-2016. The new technology is based on maximization of iron and sulfur removal into tailings and maintenance of non-ferrous and precious metals losses at the same level.After the realization of Phase 3, the annual capacity of the Talnakh Concentrator will raise by another ~ 40% at the expense of processing cuprous and disseminated ores currently being processed by the Norilsk Concentrator.By 2023, due to upgrading of the PD production facilities the emissions to the atmosphere will reduce by 75%.Polar Division of PJSC MMC Norilsk Nickel (PD) searches for the ways to solve its environmental issues. Thus, in 2016, the Nickel Plant was shutdown and a new flowsheet was introduced at Talnakh Concentrator. It resulted in the reduction of sulfur specific amount sent to pyrometallurgical processing as a component of the concentrates.The Talnakh Concentrator was put into operation in 1981 using a direct selective process to produce copper, nickel and pyrrhotite concentrates.In 1981, its design capacity for processing of Cu-Ni ores from Oktyabrsky and Taimyrsky Mines did not exceed 3 million tons per year.In 2001, a novel selective-bulk-selective (SBS) technology for the concentration of massive sulfide ore was implemented at the Talnakh Concentrator, that allowed to increase the valuable components recovery into target concentrates with feedstock grinding coarser than before."

Jan 1, 2018

By P. Prakash

A dual-drive planetary mill, which has a rotating shaft that sweeps a circle of diameter 750 mm, has been designed. The planetary mill is powered by a 5 hp motor to rotate the main shaft and a 3 hp motor to rotate the jars. The charge dynamics inside the horizontal-axis planetary ball mill was established using three-dimensional DEM simulations. The simulation results provided data to determine the impact energy distribution and the effect of process parameters such as mill speed and filling. It has been observed that the mean impact energy per unit time increases with rotation-to-revolution ratio, whereas the average number of inter-particle impacts per unit time decreases. The mill was also used to synthesize a variety of powders. Here three case studies of reaction milling are briefly presented: (i) cementite and silicon carbide, (ii) oxide dispersed strengthened (ODS) steel, and (iii) magnetite from blue dust. In each case, the powder was produced by mixing and then milling the corresponding pure components. The phase evolution, particle size distribution, and morphology of particles during milling were studied for various samples collected at different milling times using laser size analyzer, SEM, TEM, and Mössbauerspectroscopy. The results established a convenient way to produce powders of high technological and commercial value.

Sep 1, 2012

By Leon Lorenzen, Nursen Guresin, Harald Muller

The development of mining projects from discovery, exploration to actual production is a complex and time consuming process. Often poor process plant performance can be attributed to the use of non-representative samples and inadequate and/or unsuitable metallurgical test work when designing flow sheets during project feasibility study stages and specifying process equipment. Samples not representing the ore deposit and inadequate test work may lead to increased project development costs, since expensive test work and engineering may have to be repeated. It should be noted that for higher level engineering studies, larger scale test work is recommended and is a requirement for feasibility level studies. This would apply even if the technology is considered mature and well proven, as each ore body may have its own unique characteristics that, if untested at a larger scale, could result in significant design shortcomings, which will have to be rectified at later stages of the project, usually at significant additional costs

Jan 1, 2014

By M. Alvarez-Silva

The control of the amount of chromite reporting to the concentrate during the flotation of UG2 ore is of critical importance since its presence affects the downstream smelting process. It is generally reported that the main mechanism responsible for chromite recovery is through entrainment. This is reflected in analyzing the solids and water recoveries. These in turn are strongly dependent on the froth phase. In the present investigation a laboratory scale column flotation cell was used to investigate the role of the froth phase in the flotation of UG2 ore. Such a device is superior to a standard batch cell since it operates at steady state in open circuit and also allows for a greater degree of flexibility in terms of froth heights. The mass of solids and water recovered in the concentrate as well as chromite (Cr2O3) recovery by size class was determined as a function of froth height, superficial gas velocity and depressant dosage. The results showed that depressants had little effect on chromite recovery but increased the grade due to the depression of gangue minerals. A 60cm froth height always resulted in slightly lower solids, water and chromite recovery than for 30cm. Typically only 20-25 % of solids reaching the pulp-froth interface reached the launder. The relationship between solids and water recovery for a wide range of conditions indicated that chromite is mostly recovered by entrainment. Keywords: UG2 ore, column flotation cell

Sep 1, 2012

By Brochot. Stephane, Manuel Gonzalez Fernandez

"HPGR (High-Pressure Grinding Rolls) is widely used today for grinding of various kinds of ores such as iron ore or base and precious metal ores. It can be used as first stage of grinding replacing tertiary crusher and SAG mill, but also as regrinding stage to enhance mineral liberation. In addition to better energy efficiency, the advantage of HPGR is to produce much more internal particle fractures allowing faster leaching as it has been demonstrated for some gold ores. This grinding mode of compression and fracture generation also promotes mineral liberation without overgrinding. Mineral processing modelling and simulation associated to detailed ore characterization constitute a powerful tool for plant design and optimization. The mathematical models of the units of operations (grinding and separation) have to reproduce the mineral deportment for which the mineral liberation plays a central role. The present paper is focused on the HPGR modelling with the objective of plant optimization or advanced design from pilot plant tests. The traditional approach of the population balance linked to the energy dissipation and the residence time distribution is generalized in association with a mineral liberation model. The effect of the specific HPGR breakage matrix and grinding function on the mineral liberation rate is discussed and compared to the tumbling mill. The implementation of this mathematical model into a plant simulation tool is illustrated by the example of the optimization of an iron ore concentrator."

Jan 1, 2014

By V. A. Ignatkina, V. A. Bocharov, T. I. Yushina, I. M. Petrov, A. A. Kayumov

"The purpose of this research was aimed at increasing recovery of metals from rebellious sulfide polymetallic ores of nonferrous and rare metal deposits. The ores under consideration have common processing features, including textural and structural complex characteristics, irregularity of impregnation and wide range of grain size, up to nanoparticle size, variable complex mineral composition, low content of precious metals etc. This all predetermines the need for advanced processing schemes with deep selective liberation and separation of minerals with intercycle release into rough concentrate and fractional products with the use of multi-stage cycles of individual dressing, based on an optimum combination of various integrated beneficiation and hydrometallurgical processes. The application of existing standard processes does not enable the production of high-grade selective concentrates without reducing the recovery rate due to incomplete separation of fine mineral intergrowths and overgrinding of brittle ore and rock minerals.The combined beneficiation processes for such type of resources, aimed at increasing recovery of nonferrous, rare, and precious metals are based on flotation methods in combination with gravity concentration to produce rich rough collective or selective concentrates, comprising readily floatable mineral fractions. At the same time, hardly recoverable and non-separable mineral associations are released into separate concentrated products for following dressing by individual processes. The proposed combined process provides for successive selective liberation of minerals with release of rich readily recoverable mineral fractions at the preparation and ore beneficiation stages. The hardly recoverable mineral associations shall be released in subsequent operations with the use of dressing, based on a combination of beneficiation and pyro- and hydrometallurgical methods."

Jan 1, 2018

By Shen Zhengchang

Based on the flotation features of coarse particle mineral, a new type of impeller & stator unit is developed. Particles suspension state generated by this impeller & stator unit under different speeds are tested in laboratory, and critical impeller speed suit for coarse particles flotation is presented. Comparing particle suspension parameters of the new impeller & stator unit with that of KYF impeller and stator unit, it comes up that the distance between the interface of two slurry circulation channels and the cell bottom is larger in the flotation cell with new impeller & stator unit. The test results indicate that the new type of impeller & stator unit is suitable for processing coarse particles due to its good suspension capacity for coarse particles. Keywords: coarse particles, flotation, suspension, critical speed, impeller and stator unit

Sep 1, 2012

By Georg Unland, Thomas Wegner

"Impact crushers are widely used in different industries to crush materials which can vary from soft to hard and from ductile to brittle. However, the sizing of impact crushers is still based rather on empirical than on scientific approaches. Therefore, a test rotor was developed in order to investigate the principles of comminution by impact. Rocks of diabase with different diameters were used to gain the crushing properties with the following results:RESISTANCE AGAINST CRUSHINGLikelihood of BreakageThe likelihood of breakage is a function of the impact velocity and the particle diameter. The likelihood increases with higher velocities and larger diameters. Maximum Crushing ForceThe crushing force is related to the area of projection of the rock. The smaller the particles and the higher the velocities the larger are the maximum related contact forces.Contact TimeThe contact time increases with the rock diameter whereas the influence of the impact velocity is neglectable.Mass Specific Crushing WorkThe mass specific crushing work decreases with the particle diameter and increases with the impact velocity."

Jan 1, 2003

By D. P. Hatfield, G. de Jager

"Recent developments in image analysis techniques and the power of computer hardware have spurred international interest in the potential uses of image analysis techniques in a range of industrial applications. One of these applications is the control of the complex flotation process. Despite years of work, the flotation process is still poorly understood. Current attempts to control flotation cells focus on consistently duplicating the control achieved by human operators.In human control of flotation two of the dominant visual cues are the froth flow speed and the froth stability. These two factors can be measured and inferred respectively from image analysis of video of the froth surface. Two important hydrodynamic variables for control of the flotation process are the air addition rate and the level of the froth pulp interface.The current work focuses on the relationship between froth flow speed and the rate of recovery of concentrate from a flotation cell. Results are presented that show a strong relationship between flow speed and concentrate yield. These results include tests where the conditions in the cell were not changed, as well as tests involving changes to the cell level and air addition rate. Preliminary results are presented which show a correlation between froth stability and froth percent solids.Future developments of the system will include comprehensive froth texture typing, colour space and stability analyses."

Jan 1, 2003

By Paul W. Cleary

"Particle scale simulation of industrial particle flows using DEM (Discrete Element Method) offers the opportunity for better understanding the flow dynamics leading to improvements in equipment design and operation that can potentially lead to large increases in efficiency, throughput or product quality. DEM has been used for modelling many industrial applications, particularly milling. This includes ball and rock motions and power consumption in ball mills, AG and SAG mills, vibrational segregation, flows in rotating drums, operation of dragline excavators and hopper flows. In mineral processing, DEM has been concentrated on mills because of their critical importance. However DEM also offers the opportunity to improve many other parts of mineral processing operations. These areas often do not receive the attention that the key comminution equipment commands, but can become critical when they fail or under-perform. Importantly their assessment/improvement using DEM is often much more feasible because of smaller problem sizes and the absence of poorly understood physics such as breakage. In this paper we describe DEM simulations of four important pieces of non-comminution equipment that are commonly found in or near mineral processing plants (these are shown in Figure 1):"

Jan 1, 2003

By Fu Ping-Hao, J-P Franzidis, Sergio Mauricio Vianna, Ewen Silvester, Emmy V. Manlapig

"Over the last 5 years, an ambitious project has been undertaken at the Julius Kruttschnitt Mineral Research Centre (JKMRC) aiming to isolate, study and, if possible, model the effect of particle size, liberation and collector adsorption density on the floatability of mineral particles. As part of this project, we have conducted highly controlled flotation test-work, combined with state-of-the-art solution and surface analytical techniques such as High Performance Liquid Chromatography (HPLC), Time of Flight Secondary Ion Mass Spectroscopy (TOF-SIMS) and detailed mineralogical analysis to fully characterize the flotation behavior of a natural ore.The flotation tests were undertaken using a high-grade lead-zinc ore from BHP-Billiton's Cannington mine (Australia) in a specially designed continuously operated laboratory scale flotation rig. Solution and adsorbed collector concentrations were measured independently during the course of the flotation tests using HPLC based ex-situ techniques. Liberation studies were performed using the JKMRC Mineral Liberation Analyser (MLA) on selected size intervals of different streams to estimate the specific surface area of galena. These results were used to calculate the collector adsorption density (collector coverage) on galena particles, with the eventual aim of developing a mathematical model describing the relationship between pulp chemistry, feed mineralogy, and floatability of galena particles."

Jan 1, 2003