Search Documents

By Miklós Kovács

A new type of the cast in situ piles is introduced. The installation of the new pile is based on a pushing in/gaining back procedure. A temporarily closed tip element with square shaped cross-section being attached to an upper circular shaft tube is vibrated into the soil. The steel armature is embedded. Concrete is poured into the tube and, the whole structure is gained back while the tip is in opened position. The width of the tip is less than or equal to 40 cm. The maximum length of the pile is about of 14 m. Great bearing capacity is resulted from the double soil compaction effect. No spoil is generated and, the pile construction can be controlled. The paper presents the results of four loading test at three sites with some soil data.

Jan 1, 2002

By C. M. Haberfield

"1 INTRODUCTION Around the world, there is a demand for larger structures, tall buildings and large bridges. While good footing design is important for all structures, it is even more important in the case of large structures. Recent experience with footing design for tall buildings (e.g. Burj Al Alam development and Nakheel Tower in Dubai, the Gate of Kuwait in Kuwait, the City Centre Project in Bahrain and Eureka Tower and Freshwater Place in Melbourne) has shown the benefits of investing in footing planning, design and construction (Haberfield, 2011, Poulos and Bunce, 2007). The footing systems for most of these projects include the use of deep bored piles or barrettes (piles of rectangular cross-section). Many use piled rafts where the piles, while acting to support the load, are primarily used to reduce settlements. A clear understanding of the factors controlling the behaviour of the footing system is needed to enable a good engineering design to be achieved. This starts with a sound understanding of the ground characteristics and individual pile performance, including adequate collection of data and testing. The best footing solution can then be found using recent improvements in data collection and analytical techniques, complex and highly capable computer-based models and the availability of high speed computers. This paper focuses on the axial performance of deep bored piles socketed into rock – both their individual performance and their performance as part of a larger footing system. Recent research and construction practice is discussed. In practically all cases, serviceability conditions control the behaviour of the footings. Methods of establishing the parameters for input into sophisticated computer programs are described. Application of the methods to case studies is included and it is shown that the behaviour of individual piles can be closely predicted. These developments lead to lower construction costs, better constructability and shortened construction time because of the better understanding of footing behaviour. 2 FACTORS AFFECTING PERFORMANCE OF FOOTINGS ON ROCK For a typical pile-supported footing, it is necessary to consider both individual pile, pile group and raft performance. These require consideration of the behaviour of the ground immediately beneath the surface raft or footing, along the pile shaft, and at and beneath the pile toe (Figure 1). Immediately beneath the surface raft or footing, the important factors are strength for bearing capacity and stiffness for settlement and interaction effects. Along the pile shaft, of most interest are strength for bearing, excavatability and stability; stiffness for settlement and interaction effects; geology and permeability for pile stability and, most importantly, pile shaft resistance. At the pile toe all the above factors for the pile shaft are present and in addition the pile end bearing is of interest. Below the toe, stiffness for pile settlement is important to at least a depth of twice the building width."

Jan 1, 1900

By Aminul Islam, Vinay M. Kumar

"About 100 Hectares of land reclamation over the very soft to soft marine clay at Uran Creek in Maharashtra is planned. The depth of marine clay varies from 10m to 24m as observed from the geotechnical investigation. The marine clay was treated with Pre-fabricated Vertical Drains (PVD’s) installed from the elevation of +5.5mCD (chart Datum) and preload/placement of surcharge. A Settlement of soft soil mud under the reclamation was monitored using magnetic extensometer (M) and ground settlement maker (S2). These instruments are installed after constructing working platform at around +5.5m CD. Based on the field instrumentation data, the consolidation parameters were adjusted to match the theoretical and actual settlement plot. The author called this approach as “Back analysis method”. The objective of this paper is to present a case study of instrumented preloading treatment for a thick marine clay deposit. The degree of consolidation in clay strata was determined from magnetic extensometer and ground settlement marker data. Authors also determined degree of consolidation as Asaoka method, Hyperbolic method and Back analysis method and compared the results.INTRODUCTIONExpansion of Container terminal with port buildings, rail container depot, roads and utility buildings at Jawaharlal Nehru Port Trust (JNPT) is planned over a reclaimed land of 100 hectares. Uran creek predominately consists of the estuarine deposit of very soft to soft marine clay. They are characterized by low shear strength, very low bearing capacity and exhibit large settlement when subjected to loading. The additional load causes the significant magnitude of consolidation settlement over a considerable period of time. Thus for development projects on top of soft soil, the postconstruction settlement would be of primary concern.To accelerate the consolidation pre-fabricated vertical drains (PVD) were used. Pre-loading procedure was adopted to minimize the post construction total and differential settlements. PVD’s were installed at 1.0m and 1.2m c/c triangular pattern. Locally available borrow material is used as a reclamation material. The reclamation material has been placed over the existing sea bed level by land based method/end tipping method and created the working platform. The level of working platform is decided based on the tide data and it has been selected such that work should be affected during highest high water level. The PVD has been installed from the working platform and subsequently all the field instruments have been installed from the same level. Five different types of field instruments are installed to monitor ground improvement works."

Jan 1, 2017

By Brian Langdon

The DRIVEN GROUT PILE was developed in 1989 by DeWitt Construction, Incorporated. This piling essentially consists of a cost-in-place concrete piling that reacts on a steel boot that is driven to bearing. This report will describe the driven grout pile, its background and its installation. The advantages and disadvantages of this system are also discussed. Finally, the results of actual field installations are presented and discussed. BACKGROUND The DRIVEN GROUT PILE was developed out of a need for a low-cost high capacity piling (100 ton) that could be installed with ordinary pile driving equipment. This search was motivated by attempting to incorporate the material economy of an auger-cast piling with the "empirical load test" of a driven pile. Typically, the least cost material for piling in the 100 ton range is concrete (grout). A grout shaft with minimal reinforcement can withstand a compressive load of 100 tons for a material cost in the range of $6.00 to $8.00 per lineal foot. A pipe piling with a capacity of 100 tons has a unit material cost ranging to $13.00 per lineal foot. The marriage of these two advantages resulted in the DRIVEN GROUT PILE. A pile that utilizes the economy of a reinforced grout shaft and has the loading confidence of a driven pile.

Jan 1, 1990

By Osamu Taki

The development of new auger bits for soil cement column drilling equipment has made it possible to create a homogeneous mixture of soil and cement-reagent slurry. As a result, soil-cement columns are used for foundations of houses and buildings, with reliable results, as demonstrated by many field projects and laboratory tests. This paper presents and discusses construction techniques for soil-cement columns, characteristics of the soil-cement solid, quality control, bearing test results, and soil-cement foundation design procedures.

Jan 1, 1992

By D. Millgard

Dennis Millgard introduced the Session by hoping that participants to the Conference would also share their piling problems. He then invited the first speaker to present his paper. Paper 5.1. Pat Kelleher commenced by saying that he belonged to a one hundred year old firm that had experience in the New York Harbour area. They were often asked to assess the integrity of many waterside structures such as piers, walls, and docks which were deteriorating whilst still in use. The earliest structures, built in the 1800's, were on timber piles. These have now changed to Steel H and tube piles and concrete piles. Usually they were called in when the structure was showing signs of distress, or had reached the end of its life but could not be closed. In particular, they had found that marine borers had returned to New York Harbour because of the improved quality of the water. There is now a far greater incidence of attack on the timber piles than when the water was polluted. Repair is usually carried out by encapsulating the pile within the tidal range of about -2ft to +8ft (-0.6 to +2.4m). Reinforced concrete forms, reinforced fibre jackets, or nylon bags are used. Reinforced fibre jackets are used with a protective coat on the pile, while nylon bags prove the cheapest method.

Jan 1, 1991

By D. A. Bruce

The use of small diameter cast-in-place bored piles is becoming increasingly popular in the United States. Such inserts are used as conventional load bearing piles, and are generally referred to as pin piles. The other major application is for the in situ reinforcement of soil slopes or excavations. The paper reviews the applications, construction, design and performance of inserts of each type.

Jan 1, 1989

By William M. Camp

An extensive design phase testing program in which 10 piles and 2 drilled shafts were instrumented and statically load tested to failure, was undertaken to establish relevant foundation design parameters for two bridges in Charleston, South Carolina, USA. The bearing strata at both test sites was a calcareous, overconsolidated, firm to very stiff, slightly sandy, clayey silt (locally known as Cooper Marl). Confirmation dynamic and static loading tests on production piles indicated only 50 to 60% of anticipated pile capacities; including consideration of time effects. Supplemental subsurface explorations did not reveal any significant variations in marl properties. Ultimately, 22 static and 75 dynamic tests were performed on production piles for a 2 mile section of the project. Pore water pressures in the marl were also monitored during and after pile driving. A study of unit skin friction in the marl as a function of time revealed two distinct trends: piles driven in areas with a sand overlaying the marl gained more capacity significantly faster than those driven through a clay or silt. Although the insitu marl properties are apparently similar across the site, the material immediately above the marl evidently has a large effect on pile capacity. This effect of overburden on pile capacity was verified by testing piles over a period of two years.

Jan 1, 1993

By B. B. Broms

A method for calculating the bending moment induced in misaligned or bent piles is described, The maximum bending moment varies with the angular rotation between the pile segments, the coefficient of horizontal subgrade reaction of the soil and the flexural rigidity of the piles. A case history involving damages to misaligned 365 x 365 mm square precast concrete piles is described.

Jan 1, 2010

By Murray Gamble

A new type of groundwater cutoff wall has been developed at the University of Waterloo. The Waterloo Barrier? is a steel sheet piling system that incorporates a sealable cavity at each interlocking joint. In order to prevent leakage through the joints, the sealable cavity is flushed clean and injected with sealant after the installation of the piling. The installation and sealing procedures of the Waterloo Barrier? system allow for a high degree of quality control resulting in a very low permeability cutoff wall. Based upon field installations, the bulk wall hydraulic conductivity of the Waterloo Barrier? ranges from 10-8 to 10-10 cm/sec. Recent case histories are presented in which Waterloo Barrier? vertical cutoff walls have been used to prevent the off-site migration of contaminated groundwater or soil gases. In some instances, the Waterloo Barrier? system was used in combinations of applications such as preventing the migration of contaminants, redirecting the flow of groundwater, providing structural shoring for soil excavation and aiding in site de-watering processes.

Jan 1, 1997

By Timothy D. Stark

Jet grouting has increasingly become one of the ground improvement technologies used to address seepage concerns and to provide strength improvement of soils. The technique of jet grouting uses high pressure/velocity jet fluids to erode the existing soil and then to mix the cuttings with cement slurry to form soilcrete. Excess slurry or spoil is ejected to the surface. If the native soil is not completely mixed with slurry, the resulting columns will have soil inclusions which can reduce the strength of the column and/or increase the permeability of the column. A jet grout test program at Tuttle Creek Dam shows that the completed large diameter columns contain perhaps 40 to 50% or more of native soil that was not broken up and mixed during the jet grout process. The test program included excavation of full-scale columns to a depth of 35 ft (10.7 m) for visual inspection and testing. Additionally, six of the columns were cut or sectioned to investigate the interior of the columns. The observed inclusions include significant amounts of both fine grained (silts and clays) and coarse grained (fine sands and sands) soils. Evidence suggests at least two explanations: (1) fine grained soils can be difficult to erode and break up into small enough particles that can be ejected to the surface, especially if at low natural water content, and (2) when large diameter columns are being excavated, the excavated roof of the cylindrical cavity may be unstable and may collapse. With this roof instability large slabs of material can break off, fall into the slurry and escape the cutting and mixing action of the rotating jets. This paper describes the Tuttle Creek Dam test program, inclusions observed in the completed columns, and suggests potential causes of the inclusions.

Jan 1, 2009

By Andrzej Tejchman

Calculation of pile foundations should possibly truly reflect its real work, mainly with respect to the value and distribution of settlements, pile internal forces and bending moments within a slab. Many empirical and theoretical methods serving for an assessment of the settlements of pile group overestimate its actual values obtained from field measurements (see Tejchman et al., 2001). In the paper a simple engineering method for calculation of pile foundations is presented. The method takes into account the interaction between the slab and a soil together with the phenomenon of non-uniform deformation of the soil-pile subsoil, particularly under large foundations. In the method the scheme of the slab resting on one-parameter elastic subsoil is assumed. The comparison of the calculation results for existing pile foundation with the field measurements shows good agreement between those values.

Jan 1, 2002

By Vincent Joannes, Marine Lasne, Luca Brenelli, Colin Serridge, Inge van Baardwijk, Martin Stanley, Anthony Fisher, Mary Ellen Bruce, Tony Suckling, Pedro Avellanosa

"Abstract The European Federation of Foundation Contractors (EFFC) and Deep Foundations Institute (DFI) developed a sector-specific carbon accounting methodology and associated “carbon calculator” for foundations and geotechnical works. The EFFC-DFI Carbon Calculator is believed to be one of the construction industry’s first collaboratively produced carbon calculator tools for European and international countries based on verifiable and standardized data. It is intended that the tool be adopted internationally and become the open-source industry standard for ground works. A detailed methodological guide is provided with the calculator (Lemaignan and Wilmotte, 2013). This guide explains the background of the standards, accounting methodologies, emission sources and factors that were used as the bases for the tool development and includes detailed guidance on use of the calculator.Drivers for DevelopmentFoundation contractors anticipate project cost and carbon emissions will become inextricably linked in response to the climbing price of fossil fuels and carbon intensive materials as resources become scarce. Low carbon solutions will therefore become more competitive options. Also with high profile construction projects having low carbon/carbon neutrality as requirements, sustainability in the foundations industry also becomes a market issue.This carbon calculator will be used to lead the industry and shape the expectations of commissioning organisations by providing insight into the carbon cost of their projects. Commissioning organizations are encouraged to be aware of the carbon impact of projects and to also facilitate a fair and accurate way of comparing footprints to provide a level playing field for foundation contractors."

Jan 1, 2014

By A. R. Dover

The Richmond-San Rafael Bridge is a 6.92 kilometer (4.3 mile) long major toll bridge span that crosses the northern San Francisco Bay in a highly seismically active region. Tutor-Saliba / Koch / Tidewater JV was contracted by Caltrans to conduct a comprehensive seismic retrofit. The JV provided geotechnical planning and quality control services as described herein, under normal oversight by Caltrans. Part of the robust foundation retrofit design included the installation of 26 new, large diameter piles, including eleven 3.81 m (12.5 ft) diameter, cast-in-drilled-hole (CIDH) marine piles that were drilled 9.15 m (30 ft) into the bedrock beneath the Bay, where the water depth ranged up to about 21.3 m (70 ft). These reinforced concrete-filled composite piles have a steel shell permanent casing from the bridge substructure pile cap through the water column and 30.5 to 39.6 meters (100 ft to 130 ft) of marine sediments to the top of rock. This paper discusses construction, inspection (ranging from the QA employed in the planning of the CIDH pile installation methods and equipment to the actual construction inspection required for the routine installation of the shafts), problems that were encountered during construction, and the solutions that were developed and implemented. Inspection, particularly with the usual difficulties in the marine environment, coupled with the difficult and complex bedrock conditions was particularly challenging, and ranged from non-destructive testing to "in-water, inshell" diver inspection. Similarly, the complexities of dealing with both the steel casing "riser" and the associated drilled shaft (rock socket) portion of these composite foundation elements created some unusual issues. The paper also presents important lessons learned from the project.

Jan 1, 2008

By Derek Egan

"Abstract Construction clients want their foundation solutions to be right first time, every time; but it is often the geotechnical contractor who carries the most risk in achieving this. Robust validation to ensure that the installed geotechnical product is appropriate for the encountered ground conditions, will perform as required and be correctly measured for payment and record purposes is very important to minimise the contractor’s and the client’s risk. This paper outlines the development and operation of a robust real-time installation monitoring system which controls and validates the installation of driven cast in-situ (DCIS) piling. Using state of the art information technology the system allows the design engineer to interrogate the data acquired from the piling rig via his computer as the piles are completed. The use of the validation process, where data acquired during the driving of DCIS piles can be processed to estimate the finished pile performance, will be explained with reference to a new case study on large diameter DCIS piles. Examples of the routine use of the system will be presented to illustrate how automated monitoring of installation parameters can be used to raise the standard of reliability, efficiency and sustainability on piling projects. The conclusions to the paper will cover the key features and operational challenges characterising real-time monitoring of the execution of geotechnical works as developed from a number of years of experience of using a rig based data acquisition instrumentation system.INTRODUCTIONDriven Cast In-Situ (DCIS) piles have a long and successful history of use worldwide. The process, where a temporary steel drive tube, sealed at the bottom with a sacrificial base plate, is driven into the ground and filled with concrete before the tube is withdrawn, is well known (BS EN 12699, 2001 and Egan, 2013). Examples of large structures supported on DCIS piles installed by Keller UK include the Millennium Dome (now the O2 Arena) and the 2012 Olympic stadium in London.In recent times advances in piling rig instrumentation and telecommunications have enabled a new level of sophistication in the recording of installation parameters and the validation of pile performance. It is now possible to embed these features into the DCIS design and installation process which has improved the quality and efficiency of DCIS piling.This paper summarises the development and operation of a real time data acquisition and processing system for DCIS piling, but which is equally applicable to other forms of driven piling (for example concrete precast piling)."

Jan 1, 2014

By Bert R. Oastler

BERT R. OASTLER: Born Atlanta, Georgia, October 19, 1933; B.S. Civil Engineering, Duke University, 1956; Doctor of Laws, Emory University, 1966; Bryan Honor Society; Associate Editor, Journal of Public Law. Partner in charge of litigation for Smith, Currie & Hancock Including federal and state courts, administrative boards, arbitration and negotiation. American Bar Association; American Trial Lawyers Association; Georgia Trial Lawyers Association. Practiced structural steel design at Newport News Shipbuilding & Drydock Company and building construction as an officer in the United States Air Force. Engaged in the building construction business in Atlanta, Georgia as estimator and project manager for five years. Lectured on construction litigation, arbitration and government contracts procurement law for Federal Publications, Inc., Associated General Contractors and other private entities on a nationwide basis. Served as guest lecturer on Government Contracts at Emory University and Georgia Institute of Technology, Atlanta, Georgia. Served as arbitrator in cases for the American Arbitration Association.

Jan 1, 1988

By Jesse R. Jacobson

A large casino complex in Cherokee, North Carolina recently underwent a $633 million expansion that involved substantial foundation challenges. The site is located in a valley on the southern edge of the Great Smoky Mountains National Park, where subsurface conditions typically consist of varying thicknesses of fill overlying alluvium, residuum, partially weathered rock and rock. The fill and alluvium contain cobbles and boulders as large as several feet in diameter. The residuum and partially weathered rock are very thick in some areas, and the depth at which consistently high quality rock is encountered is highly variable. To reduce the foundation costs for the expansion, continuous flight auger (CFA) piles were proposed in lieu of micropiles. CFA piles are not generally used in this geologic environment and concerns regarding their selection included: (1) an uncertainty that CFA piles could be successfully constructed given the difficult conditions and (2) a lack of regional data regarding unit resistance values and load transfer characteristics. To address these concerns, a design-phase test program was undertaken to evaluate pile constructability, develop an understanding of the load transfer behavior, and establish the required pile lengths. The program included soil test borings, shear wave velocity measurements, timed auger probes, instrumented pile load tests and observation of exhumed piles. It was demonstrated that CFA piles could be advanced through the fill, cobble/boulder-laden alluvium, residuum and into the partially weathered rock, albeit with some limitations. Under axial loading, the pile response was very stiff and relatively high unit resistance values were measured. Pile instrumentation allowed for the evaluation and use of design pile lengths shorter than that tested, and the overall reduction in pile lengths yielded a 40 percent reduction in foundation cost. In general, CFA piles were determined to be a suitable, economical foundation alternative.

Jan 1, 2011

By A. Holeyman

The displacement compaction piles described in the paper are installed using a heavy casing or tube and an internal drop hammer. The casing which initially is closed at the bottom by a sand plug displaces the surrounding soil during the driving. Additional sand is rammed down through the casing during the extraction of the casing. The applications and limitations of the method are reviewed in the paper. The importance of checking the sand compaction piles during and after the installation is stressed. Indications of the compaction of the surrounding soil during the driving can be obtained by comparing the initial and the redriving logs of the casing as well as from the volume of sand added. A method to estimate the increase of the mean cone resistance as measured by CPT tests in sandy and silty soils is presented. The governing parameters are the volume of the added sand, the granulometric index and the initial cone resistance.

Jan 1, 2010

By Fathi Abdrabbo

Open caissons are used for many geotechnical engineering applications. Open caissons may be used as deep foundation elements bypassing weak soils to tip in firm deeper strata, and in rivers and maritime construction to reduce the risk of scour. Open caissons are also used for collecting sewage water through gravity sewer pipe networks or from sewer force mains. In such applications, the design and construction of open caissons require a detailed soil investigation program. In this way, the design and construction plan of an open caisson can be developed with full knowledge of the prevailing subsoil conditions. The engineering and construction techniques are key factors to achieve functional caissons. Based on close observations during construction stages, the current study presents some challenges that were encountered during the construction of two open caissons of internal diameters 20 m and 10 m (65.6 ft and 32.8 ft). This paper describes the procedure followed to alleviate the construction difficulties encountered. Site exploration program and control measures required to satisfy design and construction requirements are crucial aspects. Sinking of open caissons in dense or very dense sands is risky. Incorrect sinking of open caissons may cause extra cost, delay in construction, and harm to nearby structures. Air/water jetting near the cutting edge of an open caisson, outside slurry trench, and/or inside open trench may be used to drive an open caisson downward. Unsymmetrical work around an open caisson may lead to tilting of the caisson. If this occurs, the tilt should be immediately corrected before resuming the sinking process. Improper cleaning of fine materials on the caisson?s excavation bed, and/or inappropriate pouring of underwater concrete may result in a defective concrete seal. The paper contains a series of practical guidelines to assist those intending to use open caissons, and shares good caisson sinking practice with practitioners. Finally, the study aims to understand the difficulties encountered and to anticipate future problems.

Jan 1, 2012

By Yu Zhenquan

At the construction site of Bao Shan Iron &. Steel Mill in Shanghai, lots of RC driven piles with length of 50 to 60m were applied. The most unfavourable distribution of stress along the pile shaft was known by measuring the compressive and tensive stresses. With analysing the test results a phenomenon of impact fatigue of RC pile was discovered, the range of impact fatigue and its critical zone can be distinguished. Finally some countermeasures are presented to avoid the impact fatigue of RC long pile.

Jan 1, 1991