Search Documents

By Stephan Day

Comments on Robust M3 to Protect Water Quality ?Regulatory and philosophical thinking have tended to evolve at decade scale since 1970s. ?Mines typically last more than a decade. ?Robustness is defined by the ability to adapt to new realities. Managing Water Quality in BC ?1973 ?BC Pollution Control Objectives ?1977 ?Federal Metal Mine Liquid Effluent Regulation (Fisheries Act) ?Late 1980s ?Philosophy of ?Designing for Closure? ?1990s ?Designing for Acid Rock Drainage Management ?2000s ?Awareness of need for water quality management in general, regardless of acidity

May 1, 2010

By Lee Nichols

The Oil Sand Industry in northern Alberta, Canada, disposes of the by-products of bitumen extraction into tailings ponds. The mix of tailings sand and mature fines, with gypsum added as a flocculent, constitute a waste stream called Consolidated Tailings or Composite Tails (CT). The two main challenges of the tailings disposal process are a chronic shortage of economical containment and the potential mobility of CT deposits in the event of breaching by, for example, long term erosion, which makes abandonment of tailings ponds more complicated. Thick deposits of CT do not consolidate in adequate time to provide reassurance for abandonment of the CT containment facilities and that is why the containment must be adequately robust or the properties of CT improved for long term stability. This paper addresses potential solutions to these problems by applying the gravity drainage of CT and quasi-homogeneous construction for containment facilities. Gravity drainage is suggested as a mechanism to facilitate the consolidation of CT in critical areas of the ponds by inserting internal sand layers within the body of the deposit. Critical CT areas are defined as areas around the perimeter of containment. The advantages of this solution are long-term stability of the disposal area by creation of stiff deposits around its perimeter and facilitation of reclamation efforts on its surface. The present solution for containment of CT deposits is not favourable from a materials balance point of view. In general, sand has become a valuable resource as it both forms the primary component of the CT matrix and becomes the containment building material. If sand is required for CT, less is available for dyke construction. This puts additional pressure on the industry as a whole to maximize the use of overburden and interburden for construction of tailings containment structures. Typically, only 50 percent of dry mine waste (overburden + interburden) is incorporated into dyke construction. The remainder of dry waste is stored either in waste dumps or in tailings ponds, consuming valuable in-pond space originally allocated to CT material. Quasi-homogeneous dykes are proposed to contain CT deposits rather than traditional minimum cross-section dykes built of overburden and/or cell sand. The quasi-homogeneous dyke may change the unfavourable material balance and lessen the construction constraints that are presently imposed on the mine/waste disposal process.

May 1, 2004

By George Booth

In mining operations the cost of timber is an item of much importance, because the life of mine timbers is, in many cases, very short and, as the supply of the better grades becomes depleted, less durable kinds must be used. This, of course, tends to shorten still further the period of service-ability. While it is possible that concrete and steel may, to some extent, take the place of timber in mines, their high initial cost and the difficulty in installation will greatly restrict their use. Moreover, wood, besides being comparatively cheap to handle, possesses other desirable qualities, and for many purposes a satisfactory substitute is hard to find. Both the decreasing supply and the increasing price of timber make its more efficient utilization imperative. AGENCIES DESTRUCTIVE TO MINE TIMBERS Timber used in mines is exposed to destruction from many sources. Wear, breakage, and waste are responsible for much loss. Wood rollers and drum laggings must be frequently replaced on account of the constant wear by ropes. Unprotected timber in chutes and mills is also rapidly worn by abrasion, and track ties in main haulage ways get worn by the feet of mules, cut by ropes, etc. Large amounts of timber are broken by 'crush' and 'squeeze,' and much temporary timber is buried beyond all recovery in pillar workings and in those mines which resort to back filling. Decay and insect attack, however, cause the greatest damage. If not totally destroyed by one or both of these, the timbers frequently become so weakened that they break under the pressure upon them.

Jan 1, 1926

By Jan Rosenkranz, Anders Sand, Lisa Malm, Nils-Johan Bolin

Within flotation technology the general trend is towards very large cells. Scale-up is usually done by postulating geometrical similarity, which implies keeping the aspect ratio constant when increasing cell volume. Consequently, the design of flotation circuits typically involves several cells of identical geometry within a bank. Using a few standard sizes in a flotation plant simplifies design, manufacturing and maintenance of the cells, but does not necessarily guarantee optimal performance and selectivity of the flotation process. Geometry parameters for a given cell volume that influence flotation cell performance include cell height, which causes changes in the hydrostatic pressure and suspension hydrodynamics, and also influences the travel distance of particle-bubble agglomerates as well as the homogeneity of the mixing. Also the thickness of the froth layer depends on the aspect ratio of the cell. The objective of this work is to gain a better understanding of material distribution and properties within a flotation cell and, based on this information, elucidate how alterations of the cell geometry can influence separation efficiency. For this purpose systematic measurements and analyses of the spatial distribution of the different phases within a 160 m3 flotation cell have been carried out with a particular focus on an industrial, low-grade copper ore beneficiation process. The concepts for sampling at different vertical and lateral positions of the flotation cell are introduced. The results from the experimental work give an understanding of internal material distribution within flotation cells. Based on the measured phase distribution and concentrations as well as particle properties at various positions within the cell, the implications for an optimized scaling and design of individual flotation cells within a flotation circuit are discussed.

Jan 1, 2016

By L. C. Hsu, M. O. Desilets, P. J. Lechler, Jr. Bonham, J. G. Price, L. J. Garside

Geochemical background levels have been established for unmineralized sedimentary rocks that are elsewhere the hosts of Carlin-type gold deposits in the Getchell Trend. The Paleozoic rocks in the Winnemucca Quadrangle consist predominantly of the lower Paleozoicsiliceous and clastic sequences that were carried eastward along the Roberts Mountains thrust during the Late Devonian and Early Mississippian Antler Orogeny and the late Paleozoic Havallah and Pumpernickel sequences brought along the Golconda thrust eastward during early Mesozoic Sonoma Orogeny. Over 260 rock samples were collected from the Paleozoic sequences. Major and trace elements were determined by instrumental methods best suited for the specific elements. The general geochemical features of the Paleozoic sedimentary rocks are discussed in detail with reference to the data of average abundances of elements in sedimentary rocks. The background and threshold values of certain trace elements in sandstone, shale, and carbonate rock of one formation, as well as back-ground levels for the entire sequence were obtained. The characteristic geochemical features of the Paleozoic rocks in this area include: consistently high Ba and low Au contents (1.1 ppb, 1.5 ppb, 1.1ppb Au for average sandstone, shale and carbonate, respectively); generally low contents of those elements which may be of environmental concern such as As, Cd, Hg and Pb. Plots of major and trace elements suggest that the majority of the Paleozoic clastic rocks are related to a passive-margin tectonic setting. Samples with gold values higher than threshold are considered to have been affected by hydrothermal alteration related to gold mineralization. Most of these samples generally also have higher values of Sb, Hg, V and/or As. These observations support the use of such elements as pathfinders for gold, although V has not been identified as such before. Ba is not effective for gold exploration in this area due to the generally high background value of Ba, even though it may be an important pathfinder elsewhere.

Jan 1, 1995

By S. Ghafarnejad Parto, Å. Rasmuson, A. Fredriksson, M. Mohammadi, K. M. Forsberg, J. Martinez De La Cruz

The present study aims at recovering rare earth elements (REE) in conjunction with the production of fertilizers from an apatite concentrate. Apatite is one of the REE rich minerals ending up in the tailings pond when Luossarvaara-Kiirunavaara AB (LKAB) in Sweden processes Malmberget’s iron ore deposit. Leaching with nitric acid, hydrochloric acid, and sulphuric acid respectively have been studied. The nitric acid route was chosen for further investigations and the optimum acid concentration for leaching of the REE were determined. The leached REE are recovered by solvent extraction using di-(2-ethylhexyl) phosphoric acid (D2EHPA) and 2-ethylhexylphosphonic acid-mono-2-ethylhexyl ester (EHEHPA).

Jan 1, 2014

By Si Qin

Unknown goafs and roadways of abandoned coalmines can be a great water inrush hazard for coalmine workers. Consequently, advance detection of such hazards is of great importance. By detonating seismic charges in underground coal seams, we can collect seismic data using a surface survey line, which is located across the ground projection of the underground shot point. This experiment was conducted in a coalmine in Shaanxi Province, China. After surface elevation compensation and travel time adjustments, we accurately determined the position of the goaf boundary along the survey line based on the wave velocity anomaly on the seismic record. Then we used a scattered wave imaging technique to enhance the energy of the scattered waves that are generated when the coal seam roof slide wave (refracted wave when the incident angle bigger than the critical angle) hits the roadway, thus confirming location of a geological discontinuity (roadway). This experiment shows that the coalmine ground seismic method, employing an underground explosive charge and a surface seismic array, has the ability to detect an abandoned roadway and goaf in advance of coal mining, thus can improve worker safety.

Aug 1, 2013

By K. Wongpreedee

Recovery and recrystallization of Au wire can degrade strength and alter conductivity properties during exposure to elevated temperature. Au Deformation Processed Metal Metal Composites (Au DMMC's) are being developed for electronic applications requiring high conductivity and high strength. This paper discusses the relationships between microstructure, strength, and resistivity of Au DMMC's. It also presents the results of a recent study on the elevated temperature stability of Au DMMC's of several compositions. Au-7 vol %Ag, Au-14 vol %Ag, and Au-vol 7%Pt DMMC samples were prepared by a powder metallurgy technique. All specimens were processed into wire by extrusion, swaging, and drawing. The smallest final diameter of these wires was 120 ?m. Thermal stability was analyzed by electrical resistivity measurements to determine the relation between transformation rates and time at elevated temperature. The extensive deformation used to produce these composites reshaped the initially equi-axed powder into filaments that are 30 to 100 nm in diameter and 16 to 180 mm in length. The small filament diameter confers high strength on the composite. The high conductivity can be explained by electrons flowing parallel to the filamentary microstructure aligned with the wire axis. Using the Avrami and Arrhenius equation relationships, it is possible to predict the times and temperatures needed to achieve various degrees of homogenization. The Au DMMC's were found to have good thermal stability compared to conventional coldworked Au interconnection wires. Although these composites will revert to solid solutions if exposed to high temperatures for prolonged time periods, their relative stability is sufficient to allow them to maintain their twophase microstructure during the anticipated lifetime temperature profiles of many products.

Oct 1, 2003

By T. Krumins, L. Zunti, R. Frischmuth

Titanium and titanium alloys are commonly selected for pressure oxidation autoclave vent piping and pressure control valve components, as well as autoclave internals, in high-temperature operations. In a vent application, titanium ignition risk is reduced by limiting oxygen concentration, and preventing high gas velocity gas impingement on surfaces. Oxygen concentration is dependent on the autoclave pressure and temperature conditions and therefore titanium ignition risk is dependent on standard operating procedures, and process control interlocks and permissive conditions. It is not uncommon for standard controls to be deficient during atypical operating conditions, or for operations to deviate from the operating procedures, increasing the potential for titanium ignition incident. Titanium ignition risk caused by elevated oxygen concentration in autoclave vent systems can be reduced with the introduction of an online autoclave overpressure calculation and the configuration of associated interlocks and permissive conditions.

Jan 1, 2014

By Tracy-Lynn Humby

A recent report commissioned by the South African Chamber of Mines, Mining Vision 2030, identifies the South African mining industry?s negative legacy, its exploitation of people and the environment, as the single biggest hurdle to maximizing the industry?s impact on national development. Industry leaders have identified the need to put the past ?to rest?. With reference to three recent cases involving members of the South African mining industry, this paper points to the continuities between the past and present. It argues that the metaphor of ?multiple crossings? is more generative than the notion of putting the past ?to rest? for purposes of engaging with mining?s negative legacy.

Aug 1, 2013

By Ron Doucet

Industry today is now more than ever dependent on its assets and on the standard of maintenance. Changes in technology, environmental regulations, a continually improving focus on safety and global competitiveness has made maintenance a key activity in sustaining safe, financially viable and environmentally integral operations. Maintenance used to be looked upon as a cost centre with a sole focus of fixing equipment to attain high availability. Maintenance today affects all aspects of the business: safety, environmental integrity, energy efficiency, productivity, costs, and product quality. These new demands on the function of maintenance requires us to think vastly differently about what maintenance is all about, even to the point of contradicting old beliefs. In the following paragraphs we will examine some of the changed thinking that has evolved over the last 50 years. These new concepts will lay the foundation for the implementation of 21st century best practice maintenance.

May 1, 2003

By Gustavo Brunello

Motor Failure Rates and Cost ? Motor failure rate is estimated: 3-5% per year. ? In Mining, Pulp and Paper industry failure rate is up to 12%. ? Sometimes process downtime costs are higher than motor ?? Motor failures are due: Electrical 32% Mechanical 31% Environmental 36%

Feb 1, 2008

By R. M. de Carvalho

Empirical and phenomenological models of SAG and AG mills have dominated the scene for the last few decades, being used nearly every time a mill is scale-up or an attempt is made to improve its performance. However, in spite of their success, these models fail to describe the details of both the grinding environment and the breakage mechanisms. The result is a generally good track record, with a few – but very important – instances when these models fall short in their predictions, which can be very costly. Further, nearly all of these models require detailed calibration to industrial and pilot plant data, being costly in their application, although still with limited predictive capabilities. Recognizing these challenges, a new model framework has been proposed which overcomes the limitations of currently used models by coupling the microscale population balance model, the discrete element model and functions that describe internal classification at the mill grate. This model framework has already been applied to describe breakage in ball mills, with showing very promising results. However, in the case of SAG and AG mills a much greater level of complexity is involved in the model, given the interaction between the mechanical environment that is formed totally or, in part, by the ore itself, and the breakage response in the mill. The paper describes the model framework, demonstrating how it can address appropriately effects such as mill speed, mill filling and size distribution, on the response from the mill. Some of the advantages of the model are related to its intrinsic multi-component and dynamic nature, which allows simulating appropriately mixtures of ores of different competences in a transient manner.

Jan 1, 2012

By Selvia Tourn, Liliana Castro

"Abstract - Argentina, a large country with an important agriculture industry, needs an ever-increasing amount of phosphorus and potassium, as essential elements for plant growth. Current requirements are met from imports, but potential resources exist in Argentina. For example, several phosphatic occurrences are known in paleo-marine basins, the most significant of which are in Tertiary units in Patagonia. In addition, two types of potassium deposits are also known in Argentina: evaporite deposits in the Neuquén Basin at depths of 750 m to 1500 m contain 22 to 25 wt% K2O equivalent; and glauconitic sandstone containing about 6 wt% K2O has been identified in Patagonia.Several experiments were undertaken to test unprocessed phosphate rocks as slow-release, direct-application fertilizers, with good results. In addition, it is proposed that direct application of glauconitic sands would provide an efficient and economic alternative source of potassium. Tests with glauconite samples are still in progress. The existence of both phosphate and glauconitic rocks in Patagonia suggests that development of an extractive industry for these materials would not only help Argentina approach self-sufficiency in fertilizer usage, but also assist in the socio-economic development of this region."

Jan 1, 2003

By Shae K. Kim

The aim of this study is to manufacture magnesium alloys with alkaline earth metal oxides (BeO, CaO, MgO or SrO) additions with the objectives of (1) ensuring safety during processing and applications by raising the ignition temperature and reducing oxidation, (2) protecting the environment by reducing or eliminating use of protective gases, (3) maintaining or improving elevated temperature properties with lower amount of Ca or Sr or rare earth metals when compared with conventionally developed high-temperature magnesium alloys, (4) developing cleaner strip casting and continuous casting processes without hot tearing and (5) obtaining all of these objectives without sacrificing mechanical properties or increasing the cost of magnesium alloys.

Jan 1, 2006

By M. Moghadami

Design and construction of underground openings are associated with many uncertainties with regard to input data. In the construction process of underground openings various levels of risks exist and these affect the safety and profitability of the project. The development of underground openings can be broadly categorized into three major phases of data collection, design, and construction. A significant level of uncertainty is associated with some of the key parameters involved in the aforementioned development phases. Moreover, it is very difficult to evaluate and quantify the effects of uncertainties on the underground project construction process. Additionally, the interactions between important risk elements are typically not well understood. The intention of this study is to develop a general risk model for underground opening projects located in soils and weak rock masses. The goal of the research is to identify and quantify important geotechnical risk elements. Moreover, a weighting procedure will be proposed for the identified risk elements. Finally, all important risk elements will be assembled into a general model with emphasis on geotechnical parameters. The final objective of this study is to apply the proposed model to a real underground project scenario and verify it for actual field conditions. The proposed model, once calibrated properly, will provide a useful support tool for the decision making process.

Aug 1, 2013

By Matthew Violot

Vale Canada?s Birchtree Mine, located in Thompson Manitoba, has been experiencing problems with hanging wall / footwall dilution, as well as sloughing off of adjacent stopes and temporary stope block backs. Birchtree Mine is interested in determining how time affects the stability of their open stope blocks. Many factors simultaneously influence open stope stability (rock mass quality, joint condition, stress condition). This makes it challenging to determine the influence of a single parameter such as exposure time or stand-up time. This study focuses on determining the effect of exposure time on open stope dilution and combines stress analysis and empirical based approaches.

Jun 1, 2012

By K. W. Fritzsche

The prosperity of any nation depends, to a large extent, on its natural resources such as oil, coal, 'metal, timber, waterpower, and fertile soil. Each one of these resources forms the basis of a huge industry. The mining and smelting industry ranks among the first since it paves the way for a number of other industries. The mines and smelters provide a market for electric power, coal, timber, and agricultural products: other industries in turn provide a market for metals and non-metals. The real pioneering, however, is done by the prospector who goes into the wilderness to search for the ores from which the metals are to be extracted for the use of men. Prospecting is an interesting and fascinating occupation. There are many difficulties and hardships in the way but the lure of gold and the vision of finding an outcrop that may develop into a large bank account, within a reasonably short time, will urge the prospector forward. Thus, on the outskirts of this northern hemisphere hundreds of prospectors are searching and toiling and of whom nothing is known or heard until they reach civilization and announce a new discovery. Then a mad rush takes place and everybody who can afford to go will take a gamblers chance and plant stakes in the neighbourhood of the new discovery, or wherever an outcrop of mineralized rock can be found, with the hope of winning a fortune.

Jan 1, 1925

By Hans Lundberg

Magnetic methods have been used for more than three hundred years in prospecting for magnetic ores. More recently magnetic methods have been used for finding salt domes and studying certain geological formations. A number of instruments have been developed and substantial improvements made as to their sensitiveness and accuracy. Papers and articles written on magnetic methods are generally elaborate and technical, and the average prospector finds it difficult to obtain the necessary information as to how to operate the simple magnetic instruments to the best advantage. The miner's compass, dip needle, and inclinator are, indeed, very useful instruments and are easy to handle, and a great deal of valuable information can be gained if the instrument is properly operated and the results correctly interpreted. The lack of knowledge of the fundamental principles, however, has caused a great deal of disappointment. Other and more elaborate geophysical methods have recently come into the limelight, and the prospectors seem to have lost a great deal of interest in the dip needle. This is much to be regretted, because magnetic methods have a particular field of use. The present article is an attempt to help the prospector regain interest in the magnetic instruments and to show the use and application of a simple magnetic survey. If the prospector expects some useful help in his work, he must, of course, know the instrument, know how to take the readings, and know how to plot and interpret the observations.

Jan 1, 1929

By H. Kroog

"This contribution reports recent mineral sorting experience and lists the possibilities of the newest generation of automatic mineral sorters with a special focus on electromagnetic detection, optoelectronic technology and the latest innovative X- Ray transmission units. In industry, mineral and ore are still hand-picked and current automation potential is only utilised in a handful of specific applications. Recently a number of technological developments took place that may increase sorting potential, save mill costs and lead to lower overall tonnage costs. The mentioned technologies provide automatic dry separation of minerals and rock as an alternative for conventional processing. The MikroSort technology is environmentally friendly:•,The remaining waste is free of contaminations•,The dump volume is reduced•,The concentration of the high grade material•,at an early stage saves resources"

Jan 1, 2005