Search Documents

By Ian Rozier

"Emphasis in recent years in western Canada has been placed on the development of large open-pit coal mines, the most notable developments being in northeast British Columbia. However, vast resources exist below the limit of economic open-pit mining, and with world demand predictions of the late seventies in mind, the potential of underground coal mining in western Canada has been investigated. Particular emphasis has been placed on the Plains coalfield of Alberta, and there is optimism that underground coal mines will be developed in the Lethbridge area of southern Alberta.With no existing operations in southern Alberta with which to compare mining conditions, any mine planning and feasibility level studies rely heavily on the engineering/geotechnical data obtained from surface investigation to predict ground control problems and technical constraints on mining. Such investigations have been integrated with exploration drilling programs. Emphasis has been placed on extracting maximum information to provide an over-all appreciation of potential ground conditions and to identify specific ground control problems that could be encountered.The acquired geotechnical parameters are then used to evaluate the mine properties from an engineering standpoint for input into the determination of optimum mine layouts, development directions, mining methods and roadway and face support requirements. These geotechnical studies have been primarily directed toward the longwall mining method, but the acquired data base could equally be applied to alternative mining methods.In addition to the lithologic and structural controls which relate to roof stability, caving characteristics, floor heave and subsidence, investigations have been directed at gaining an understanding of the over-all surface and ground water regime with respect to potential inflow into the mine openings and ground control problems that could be caused by inflows encountered during mining. Experience has shown that soft floor conditions and water control are important factors to be considered in a longwall layout, and without doubt these parameters will play a major role in the design and operation of a successful longwall operation in the Lethbridge coalfield."

Jan 1, 1986

By G. T. Lapidus, O. J. Solis-Marcial

Currently, ores with high-grades of copper oxides and secondary sulfides have become increasingly scarce, which has encouraged industry to look for alternative raw materials to obtain copper. The problem is that primary sulfides are difficult to dissolve at near ambient conditions. Proposed hydrometallurgical processes have not been implemented beyond a pilot or demonstration scale. One of the principal disadvantages is that the majority of these processes are not viable with ores that contain less than 4% copper. One of the more recently proposed techniques involves the use of organic solvents in the dissolution of copper concentrates with a chalcopyrite content of between 20 and 30%, which has shown high efficiency. The present research explores the ability of this process to leach copper from low grade chalcopyritic ores (<4% Cu) at different temperatures ranging from 20 to 50°C. It was found that depending on the temperature, high percentages of copper were extracted in 40 to 100 minutes, using different oxidants. Additionally, distinct leaching behavior was observed with each oxidizing agent. In some cases, the extraction kinetics adjusted to the diffusion controlled shrinking core model.

Jan 1, 2014

By J. J. Benitez

MIBC (methyl-isobuthyl carbinol) was previously shown to enhance significantly sylvite flotation when used at the stage of preparation of amine dispersions. In this paper Atomic Force Microscopy (AFM) is used to study the effect of MIBC on deposition of octadecylamine (ODA) on the surface of mica. The AFM images indicate that amino terminated, and therefore hydrophilic, deposits of ODA are observed on the mica surface in the ODA dispersions free of MIBC. In the presence of MIBC a methyl terminated (hydrophobic) monolayer is obtained on the mica surface. The transition between the monolayer and bilayer phases is due to the presence of MIBC. Experiments carried out in distilled water reproduced the results obtained from the brine. Working in pure water instead of brine simplifies the preparation conditions and the analysis by AFM.

Jan 1, 2006

By Ajit K. Sinha

"Electromagnetic surveys were conducted over the Yava sandstone-hosted lead deposit in Nova Scotia to evaluate the usefulness of such surveys for detecting and mapping sedimentaryhosted metallic ore deposits. Both transient and multifrequency systems were used for that purpose. The deposit consists of three zones of disseminated galena which also contain minor amounts of pyrite and sphalerite filling the interstices of the sandstone grains. Each zone overlies a basement depression and is separated from the adjacent zone by an intervening basement high. A conductive shale layer underlies the galena-rich sandstone formation at all three zones.Because the concentration of galena (3070 to 4% ) and other sulfides is too low to affect the resistivity of the sandstone formations for detection by ground electromagnetic (EM) methods, the strategy for our survey was to look for areas of basement depressions and the presence of conductive shale in those depressions by EM depth soundings. The presence of the galena-rich sandstone formations could be inferred because of the close association of these two features with the deposits in the Yava area. Both transient and multifrequency EM systems were successful in mapping the basement depressions and detecting conductive shale at the three known mineralized zones. The technique, therefore, seems to offer good prospects for mapping similar stratabound sedimentary-hosted sulfide deposits."

Jan 1, 1993

By P. R. Warner

This paper reviews the development of certain aspects of the electrical specifications of Anglo American’s suite of specifications for gearless mill drives (“GMDs”). These specifications are based on experiences in both Anglo American’s and others’ operations, benchmarking against large hydro generators, the advice of industry and university experts, and continuous close co-operation with OEMs. To achieve a step change in availability additional final testing and electrical protection have been implemented, insulation requirements have been specified for machines to be operated at high altitude and clean area and access control systems have been developed.

Jan 1, 2012

By Zainelabdin Khalid Zainelabdin Elfaki

The influence of partially replacing cement with marble waste on the workability and compressive strength of concrete bricks was investigated. Three replacement percentages, 10%, 20% and 30% weight marble waste, were used with different curing times of 7, 14 and 28 days. Two specimens were prepared for each percentage and curing time. For this study, marble powder from the Mining House Company in Saudi Arabia was used. It was observed that the replacement of cement in Concrete brick with marble waste enhanced the loading strength and the workability of the prepared concrete bricks. It was also observed that 20% replacement of cement with marble waste was the best replacement percentage compared to the other replacement percentages tested. Marble waste from manufacturing companies, either in powder, sludge or slab form, has negative impacts on the environment. In contrast, reusing marble waste has both economic benefits (i.e., selling the marble waste) and lessening the need for raw resources.

Jan 1, 2014

By Q. Li, X. -L. Lei

Accompanying global energy shortage and high energy prices, shale gas has been the focus of exploration and it has attracted great attention from both academia and industry. The combination of horizontal drilling and hydraulic fracturing enables the extraction of huge quantities of shale gas from impermeable shale formations. During the process of hydraulic fracturing, great amounts of water, sand and chemicals must be injected into the shale formation at a high pressure, which may trigger seismicity. Such events could occur due to the presence of faults or the reactivation of these potential faults. Shale is the main component of source rock in the Sichuan Basin, China, and has the greatest contribution to the natural gas of the basin. In order to investigate the fracturing mechanism of shale in the Sichuan Basin, China, a series of rock fracture tests under triaxial compression were carried out in the laboratory in order to investigate the hydraulic fracturing behavior in relation to the seismicity. Based on the high multichannel waveform recording system, the detailed spatio-temporal distribution of acoustic emission due to micro-cracking was used to examine the deformation and fracture behavior of shale. In addition, the effects of confining pressure on the deformation and fracture in shale under triaxial compression by acoustic emission monitoring and X-ray computed tomography were discussed in the paper. The experimental results indicate that the shale samples demonstrate brittle fracture behavior. The confining pressure has a great effect on the complexity of the fracture planes and the spatial distribution of acoustic emissions, but few contributions to the location of the major hydraulic fracturing plane. The foliation of shale plays a dominant role in the rupture process and the geometry of the major hydraulic fracturing plane. The high confining pressure increases the strength and restrains the deformation of shale during compression process. These results shed some light on the understanding of onset of hydraulic fracture initiation not only for shale gas exploration and production, but also for CO2 geological storage and underground energy storage.

Jan 1, 2015

By So-Yeong Lee, Moosang Lee, Seung Hwan Ahn, Ho-Sang Sohn, Jongshin Chang

It is necessary to understand the characteristics, phase changes and chemical reactions of flue dusts introduced from a furnace to an off-gas line in order to achieve the stable operation and the improvement. This study is to develop the dust reaction model for chemical reactions of dusts in an uptake shaft of smelting furnace and a waste heat boiler. Phase equilibria and reaction paths in this system were determined by thermodynamic calculation with experimental and industrial data. The oxidation reaction rate of dusts was determined by the gas film mass transfer controlling. And the sulfation reaction rate was evaluated by the unreacted shrinking core model. Kinetic parameters were estimated by reference data including industrial ones. The present study with the developed model shows various effects of temperatures, dust particle sizes, and O2 gas partial pressures on dust reactions. INTRODUCTION The flue dusts from a copper smelting furnace move along a furnace off-gas stream into an uptake shaft and a waste heat boiler (WHB) and electrostatic precipitator(s). It is necessary to control the dust quality in order to stabilize the operation because the sticking behaviors differ depending on the phase of dusts. Phase changes of dusts are caused by chemical reactions at given conditions such as temperature and partial pressure of gases. Therefore, it is required to understand the phase changes and chemical reactions of dusts in order to perform the improvement and stable operation. The present study carried out the investigation to understand their fundamental knowledge. Especially, this study was focused on the kinetics of chemical reactions of flue dusts, developed the model. In particular, the scope of development and utilization of the model was defined as the uptake shaft of the Mitsubishi S furnace and the S-WHB radiation section in the Onsan smelter. Information needed for the modeling work referred to data from these processes.

Jan 1, 2019

By Huan-Qiang Zhang, Gang-Hai Huang, Yu-Yong Jiao, Fei Zheng, Zhang. Xiu-Li

An efficient and accurate three-dimensional (3-D) contact detection algorithm is of vital importance in large-scale computing of discontinuous deformation analysis. The contact detection algorithm takes up a large proportion of the whole calculation time because of the increasing calculation number in three-dimensional case. For block systems which consist of convex polyhedrons, the efficiency and accuracy of the contact detection algorithm is a great challenge. The presented contact detection algorithm in discontinuous deformation analysis (DDA) method is carried out in three phases: the global neighbour searching, the local contact type searching and the contact transferring. A contact detection algorithm for 3-D DDA is presented with some improvements on the three phases. A grid-based global neighbour searching algorithm is used to eliminate unnecessary neighbour blocks to the exact number. The local contact type searching includes two steps. In the first step, the common plane method is used to determine the contact type between convex polyhedrons. In the second step, the contact pairs detected by the common plane method are divided into four basic types. In the third phase, the four contact types are transferred into two basic contact types, vertex-to-face contact type and edge-to-edge contact type, which are managed in a uniform procedure. Three verification examples are calculated, the results show that the proposed algorithm based on the three contact detection phases is robust and efficient.

Jan 1, 2015

By Per-Lennart Nystedt

"The Boliden Lead Kaldo Plant for the treatment of lead bearing flue-dust from the Copper Smelter and the Slag Fuming Plant has been in operation at the Ronnskar Works of Boliden Metall since the middle of 1976. At the present stage, the plant can treat lead-bearing dust of different kinds and compositions. The process allows good separation of arsenic and halogens from lead.The flue dust from the Copper Smelter and the Slag Fuming Plant is very complex and, apart from lead, also contains zinc, copper, tin, bismuth, cadmium, antimony, arsenic, sulphur, silver, chlorine and fluorine. The metallurgical process has been developed by Boliden Metall and has been tested on a pilot scale at the Foundation for Metallurgical Research (MEFOS) in Lulea, Sweden.The pelletized dust is smelted in the converter, where the heat is generated by an oil oxygen burner. The second step consists of reduction with coke. A lead bullion and slag are obtained. The slag, transported in liquid form, is treated in the Slag Fuming Plant for the recovery of zinc. The third step is the elimination of arsenic from the bullion. This is achieved by treating the lead with iron (turnings or pellets). The result is a crude lead and speiss. The lead contains silver, tin, antimony and bismuth, and is suitable for the final refining stages in normal plant equipment for refined lead.For process control, we use the rapid analysis centre, which is pneumatically and electronically linked to &apos;all major plant sections and allows for a quick turn-around between delivery of the sample and feedback of results. All three steps in the process are performed in the same converter.Since the starting up of the plant, the original process has been subjected to some modifications. Initial problems related to equipment, maintenance and environment have been solved step by step. Examples are quoted. Recent operating particulars are presented."

Jan 1, 1980

In the last 30 years numerous mining plants have been developed in North America but only a handful of these have required freezing the area where the shaft was sunk. The most recent mine shaft to be sunk using this technique is located on an island off the coast of Louisiana. The project required the input and skills of numerous people in several companies, including the owner, engineers and contractors. The Cote Blanche installation is one of several mines in the area which extract salt from a dome which extends under the Gulf of Mexico. The geology of this area is, however, markedly different from others in the region because there is approximately 460 ft of water logged soil above the salt dome. Because it is not possible to sink a shaft in ground that is this soft, the overburden where the shaft is located must be frozen before excavation can take place. The Cote Blanche mine is a producing facility which was built in 1958 by the Carey Salt Company. The original facility included a 14 ft diameter production shaft and a 7 ft-8 in diameter service/ventilation/escape shaft. This system was installed by The Cementation Company. In 1996 the owner decided to improve both the mine ventilation and production hoisting system by installing a third shaft. This shaft would be designed to extract 650 tons per hour from a depth of 1600 ft and provide 500,000 cfm of ventilation to the mine at a maxium design pressure of 4 in WG. These parameters resulted in a requirement for a 16 ft finished inside diameter concrete lined shaft and a headframe designed as a pressure bulkhead. Because the mine would operate from one level only, the most efficient hoisting system for the application was determined to be a ground mounted koepe running on rope guides. With these criteria fixed Cote Blanche embarked on a program which would see construction start in June 1998 with the first salt produced in February 2001 at a cost of $US18M. The major players in the design and construction were G.L. Tiley & Associates Ltd., BLM Bharti Engineering, Freezewall Inc., Phillips Mining, Geotechnical and Grouting Inc., Don Hart Consulting and Dynatec International.

May 1, 2002

By Robert B. Parsons

"The February 18, 1987, Federal Budget contains a proposed amendment which would simplify somewhat the ""successor corporation"" rules in the Income Tax Act. Despite this amendment, though, the important successor rules will continue to be relatively complex.IntroductionThe February 18, 1987, Federal Budget papers propose an income tax amendment whereby the so-called ""successor corporation"" rules would be revised by removing the present provision which limits the application of these rules to a maximum of two ""successions"". The successor corporation rules represent one of the most complicated sets of rules in the Income Tax Act. This month, Tax Notes seeks to explain these rules and the proposed amendment in simplified terms.Basically, the successor rules provide a mechanism for transferring unused exploration and development expenses from one taxpayer to another , in specified circumstances. The aforementioned limitation of two successions refers to the rule which allows a maximum of two such transfers with respect to any particular pool of deductions."

Jan 1, 1987

By James A. Deeks

"Motor failures and equipment bearing failures are responsible for reduced productivity.With the introduction of computers and data acquisition systems, users are now able to monitor, report and trend deteriorating conditions and take corrective action before a critical shutdown occurs.This paper discusses the monitoring and trend analysis of&apos; motors, and motor and equipment bearings. With today&apos;s digital electronics technology users are now able to monitor their equipment, detect deteriorating or abnormal conditions quickly, alarm the condition locally and or remotely, and decide if immediate corrective action is necessary or if it can be delayed until the end of a work Shift. All of this can be done long before any damage is done to the equipment.Monitoring Trend AnalysisIt is no longer necessary to compromise in selecting products, since state-of-the-art designs allow the adjustment in such small increments that the users are able to detect minute changes in a system&apos;s performance.Monitoring and trending of motors and equipment bearings is now available in economical packages which can be expanded as a system grows. Simply select the information you need, set the parameters, choose the scan time, and decide on the degree of reporting.Buffer storage of short-term monitoring of a number of analogue channels permit the user to view the recent history of motor data such as: motor average load, unbalance, motor current, ground fault, reserve thermal capacity, plus all of the settings of the protective device.A decision can be made to freeze the stored information after the motor stops or after the motor starts. Then the user is able to recall the conditions and diagnose the performance and the cause of the abnormal condition. Typical scan times range from ¼ second to 5 seconds ."

Jan 1, 1992

By Harvey McLeod

M3 -Technology HOWEVER:In practice we have limitations ?Clients: aggressive or cost based; inexperienced ?Consultants: ?expanding market w/training limitations ?Prescriptive designs ?Lack of senior oversight ?Regulators: difficult to retain technical capacity ?Stakeholders: perceptions and expectations ?Physical settings: challenging terrain, climate, soils/rock Do M3?s Perform? YES?Generally M3?s since mid-1960 do perform ?BC Closed Mines: Afton, Highmont, Trojan, Bethlehem, Cheni, SNIP, NO?ARD/ML issues?e.g. Equity Silver, Samatosum; selenium, cadmium, sulphate

May 1, 2010

By T Nakamura, M. Itoh

Most of the used cathode ray tube (CRT) glass in Japan, which contains lead oxide, was exported and recycled in overseas factories of new CRTs. However, domestic treatment and recycling of waste CRT glass has become necessary because overseas CRT factories have shut down and exports of CRT glass have stopped. Some of the waste CRT glass recycled domestically is charged in lead blast furnaces instead of silica flux, because there is no local reproduction route for glass that contains lead. However, the mass of CRT glass that can be treated in this manner is limited because of its high silica content. Consequently, additional treatment methods for waste CRT glass are required so that more can be used as a lead smelting material. In this study, waste CRT glass was treated with hydrofluoric acid to dissolve the silica contained in the glass, and the dissolved lead was recovered by precipitation. Lead metal was recovered by electrodeposition from the prepared hexafluorosilicic acid solution.

Jan 1, 2011

By S. Timbillah, R. LaDouceur, C. A. Young

A low carbon-chain trithiocarbonate ((NaOOC)CH2SCSSNa), known as Orfom® D8, was tested as an organic depressant in the differential flotation separation of chalcopyrite and molybdenite in the presence of sodium isopropyl xanthate (SIPX) or potassium ethyl xanthate (KEX). Flotation studies show that Orfom® D8 depressed chalcopyrite while molybdenite remained floatable. A study of the mechanism of adsorption indicated that Orfom® D8 adsorbs on chalcopyrite through its trithiol (CS -) functional group via both chemisorption and Orfom® D8-metal complexation. The Orfom® D8 depressant is selective and does not form any Orfom® D8-molybdenite bonds. Thus, the combination of the depressant in the presence of either collectors depressed the chalcopyrite and floated the molybdenite. Fundamental parameters of the Orfom® D8 including pKa determination as well as possible decomposition products of the depressant are reported. This study includes an economic case illustrating why using Orfom® D8 can be beneficial. INTRODUCTION Depressants are incorporated in mineral flotation units in the minerals processing industry to make or keep certain minerals selectively hydrophilic. Most reagents used are inorganic and include, for instance, sodium hydrosulphide (NaHS) which is the major reagent used for depressing sulphide minerals, particularly those containing copper, iron and lead. However, the issues with its use include high toxicity, tendency to explode, strong odour, and high consumption due to required high dosages as well as its tendency to oxidise in air. The latter can be overcome by conducting flotation in inert atmosphere such as nitrogen and recycling of the flotation process water. The use of more novel depressants that are essentially organic including homopolar reagents with hydrophilic functional groups on both ends of its structure adsorb onto a target mineral surface with one polar end, the other polar end orients into the bulk solution making the surface hydrophilic and thus, ensuring that the desired mineral does not float. The stringent environmental and safety regulations being implemented in recent times mean that the search for more environmentally friendly chemical reagents is a must have. The use of organic depressants for flotation systems such as Cu-Mo sulfide bulk concentrates has become increasingly important because of the health, safety and environmental issues surrounding the use of inorganic depressants. Nagaraj et al. (1983) investigated the Cu-Mo sulphide flotation system using a structure-activity study of depressants. They found that a major advantage of organic depressants is the ability to tailor-make organic molecules to suit many requirements and thus, eliminate the guess work approach that was predominant in the industry.

Jan 1, 2019

By K. G. Markkola

Since 2005, Compafifa Contractual Minera Candelaria (CCMC) has defined various strategies which aim to optimize the usage of the available energy in each of the SAG grinding circuit modules (SABC-A configuration). For this purpose, the use of larger size balls along with operating with an optimum balls/load ratio has been implemented. Additionally, in the ball mills, the amount of balls in relation to the equipment&apos;s usable diameter has been optimized. In the pebble crushing circuit, the percentage of material passing 12 mm (112 in) product has been increased by 15% by: (1) modifying the crusher mantle profile, (2) implementing a strategy for maximizing the power in each crusher, (3) using continuous improvement tools (Lean - Six Sigma), (4) redesigning SAG mills discharge grates, and (5) changing discharge grates in order to control the crusher feed size distribution profile. All these activities have improved plant throughput by 1,000 t/d with no significant capital investment. As part of the energy consumption optimization study, we have considered determining the optimum operational rate of each SAG mill, in relation to the mill liner life and also the improving the control strategy in conventional grinding.

Jan 1, 2007

By William H. Pomroy, Kenneth E. Hjelmstad

An underground mine fire can seriously threaten the lives of all personnel in the mine. This fact makes fire emergency planning a high priority in the mining industry. A fire emergency plan includes a means of warning miners of the existence of a fire, and the need to evacuate or retreat to a place of refuge. The warning alarm must be fast and must reach all miners, regardless of their location or work activity. Means of fire warning are varied, and include such methods as stench, flashing lights, telephones, and word-of-mouth (messengers). Unfortunately, none of these methods are entirely satisfactory. Stench can be slow and seldom achieves total mine coverage, especially in high-back room-and-pillar mines with low ventilation velocity. Telephones are effective only where personnel are close enough to hear the phone ring. A novel fire warning alarm system has been developed by the U.S. Bureau of Mines which enables instantaneous warning of all underground personnel. The warning alarm is sent by an electromagnetic signal which penetrates through mine rock from a transmitter to small person-wearable receivers. Each miner&apos;s cap lamp battery could be equipped with a small receiver and when a fire or other emergency occurs the miner could be alerted to the danger by a blinking of the cap lamp. Testing of prototype equipment has demonstrated that the transmitted signal is capable of penetrating through over a mile of mine rock and activating the receiver. This paper describes the theoretical basis for through-the-rock ultra-low frequency electromagnetic transmission, design of the prototype transmitter and receiver, test results, and status of commercial development of systems utilizing this technology.

Jan 1, 1994

By Y. P. Wu

Steeply dipping seam refers to the coal seam with dipping angle in the range of 35?55°, which is well recognized to be very hard to mine by the mining industry all the world. In the last two decades, some fundamental researches were focused on the strata behavior of long-wall panel, complicated rock mass breaking process of the steeply dipping seam, overburden stress field developing and evolution, rock strata breaking and moving process, rock structure stability mechanism and control. Results show that it?s presenting macro stress arch-shell (MSAS) of the stress distribution of the overlying rock in steeply dipping seam. The MSAS is the spatial distribution of intensity envelope line under the strength criterion and has the geometry shape asymmetry as well as the stress distribution heterogeneity. The arch- shell base will forward as the working face mine forward and the shell roof will extend to higher overlying strata above the gob. In this paper, the stress arch-shell analysis model and coordinate system were established and analyzed the inclined masonry structure at different zone. Analysis results show that the rock damage at the key part of the arch-shell is the main factor which causes whole overlying rock structure failure. The rock structure instability modes have tension instability of the shell roof, compression-shear instability of the shell shoulder and composite instability of the shell base, meantime, instability coefficient is proposed to determine instability condition. The above research results enrich the complex coal seams mining theory and provide a theoretical basis for mining safely and efficiently in steeply dipping seam.

Aug 1, 2013

By Ron Jessulat

"IntroductionBrunswick Mining and Smelting Corp. Ltd. is a IO 500 tid base metal producer. Development is carried out by Jarvis Clark MJM-21 3-boom development jumbos, using Tamrock E400, 410 and 550 pneumatic drills. Typical drift size is 13 ft by 18 ft with a 12-ft advance per round. Blast holes are 1 ½ in. in diameter while reamed holes are 3 in. in diameter. AN/FO is the principal blasting agent, being loaded by C-I-L model60R intermediate loader. The detonators are NONELS and DETINELS. Sulphide dust explosions occur during blasting when dusts from certain minerals such as pyrite and pyrrhotite are ignited by name from the detonating shots. The result is a secondary unwanted explosion with a characteristic shock wave and name front that are very destructive to mine services such as ventilation ducting, electrical cable, and ventilation control doors.A typical reaction in the Brunswick orebody occurs according to the chemical formula:4FeS 2 + IIOs-2Fe2O3 + 8SO2 + 3458--(Enright , 1988)The hematite (FeO3) is deposited as a red dust in the blast area while the toxic sulphur dioxide gas (S00 contaminates the underground workings . The presence of S02 gas disrupts production until it is purged from the area by the mine ventilation system or dissipates slowly in those areas where the vent ducting has been melted by the name front or torn down by the shock wave.Sulphide dust explosions exact a high economic toll. Direct costs in damaged materials and wages are probably exceeded by the value of lost production and disruption to the mining cycle. In addition, the health and safety concerns associated with sulphide dust explosions cannot be ignored."

Jan 1, 1993