Search Documents

By M. S. Moats

"The effects of commercial copper electrorefining additives (glue and thiourea) on the electrochemical removal of bismuth are of importance in copper production. It was found that Bi(III) electrodeposition occurs readily from acidic sulfate solution via a diffusion-controlled quasi-reversible reduction. The diffusion coefficient of Bi(III) was measured and found to be less than reported values of copper in similar solutions. The presence of thiourea and/or glue was found to accelerate or de-polarize Bi(III) reduction on stainless steel as compared to the inhibition or polarization of Cu(II) reduction. The additives also inhibited the dissolution of the Bi-Cu co-deposit during cyclic voltammetry. During short term deposition studies, the additives increased the concentration of Bi in co-deposited Cu-Bi products from solutions with low concentrations of Cu (<2 g/L). Bi deposition was significantly suppressed by increasing the Cu(II) concentration in the solution. The formation of a copper layer on the stainless steel electrode appeared to significantly suppress the reduction of Bi(III). This study demonstrates that glue and thiourea depolarize the deposition of bismuth on stainless steel. Therefore, the additives could be used to improve Bi impurity removal during third stage liberation.INTRODUCTIONThe production of high purity copper has been steadily increasing due to the wide application of the metal and its alloys in electrical and electronic products, infrastructure construction, industrial machinery and equipment, general products and transportation (Moskalyk et al., 2003). Most high purity copper is manufactured from copper sulfide mineral concentrates and/or scrap via a pyrometallurgical process followed by electrorefining (Navarro et al., 1999). During the electrorefining process, cast anodes of 99-99.5% purity are electrochemically dissolved into an acidified copper sulfate solution while high purity copper (>99.99%) is plated on stainless steel blanks or copper starter sheets (Davenport et al., 2002). The control of cathode deposit growth (purity and morphology) while maintaining a high current efficiency is of significant importance for copper refining (Ilkhchi et al., 2007). At typically applied current densities for industrial copper electrorefining, mass and charge transfer play important roles in the quality of cathodic products (Hiskey et al., 1998). If the real current density at some surface points is substantially higher owing to uneven current distribution, then rough spots can and will grow faster leading to nodules (Suarez et al., 1992). Nodulated deposits tend to capture solution and anode impurities (slimes) resulting in unacceptable cathode quality (Afifi et al., 1987). Furthermore, these nodules can grow until they eventually contact the anode leading to short circuits and current efficiency reduction (Ilkhchi et al. 2007)."

Jan 1, 2016

By Fathi Habashi, Ernesto Bourricaudy, Fouad Kamaleddine

Ilmenite occurs in black sand at the mouth of great rivers as in India, or as massive deposits like in Quebec Province in Canada. It is unsuitable for processing into pigment or for metal production because of its high iron content and its low grade. Pyrometallurgical and hydrometallurgical methods have been developed to cope with this problem which resulted in the production of two commercial products that became known as synthetic rutile and Sorelslag. Attempts are also underway to produce TiO2 pigment directly from ilmenite. This report presents a newly developed process called the Magpie process, which enables the production of high-grade synthetic rutile (over 95% TiO2) from low grade ilmenite (10-12% TiO2). Naturally, if such process is applied for low-grade ore it can be applied with advantage to high grade material as well.

Jan 1, 2014

By Tony Lipiec, Ian Orford

"A key part of plant design is the selection of the design tonnage which is the hourly tonnage target that the equipment selection is based on. Its selection is critical for ensuring that the nominal tonnage which is critical to the financial performance of the project will be met. With deposits being developed at lower grades, higher tonnages and a higher degree of hardness variability, it is essential to ensure that the design process selects the comminution equipment which will be able to deal with the impact of this ore quality variation.Ore hardness and its variance are key factors to be taken into consideration for the selection of the design tonnage. It is well accepted that for the nominal or name plate tonnage to be consistently achieved, it is necessary to base the design tonnage on a hardness value greater than the average ore hardness of the deposit to be mined. The question is how much greater should this design value be to ensure that the nominal tonnage is met to the satisfaction of the project financial model. Standard industry practice is to set the design tonnage by:1. Select an ore hardness percentile that is greater than the average ore hardness to be the basis of the nominal tonnage. Typically either the 75th or 80th percentile value from the data set will be selected.2. Selection of a design factor to multiply by for determining the design tonnage, i.e. the design tonnage = tonnage (based on the average ore hardness) multiplied by design factor.This paper discusses the selection of the design ore hardness through the use of modelling or the use of a design factor. It further shows the impact of ore hardness variance on the capacity of the process and its ability to meet the nominal tonnage. Insight is provided as to what ore hardness percentile value should be selected balancing the shortfalls of tonnage for ores harder than the design value versus the above target production achieved for ores softer than the design ore hardness."

Jan 1, 2016

By J. H. Reiss, D. F. Bruhn, Idaho National Laboratory, Y. Jiao, D. W. Reed, Y. Fujita, D. L. Daubaras

"Bioleaching offers a potential approach for recovery of rare earth elements (REE) from recyclable materials, such as fluorescent lamp phosphors or degraded industrial catalysts. Microorganisms were enriched from REE-containing ores and recyclable materials with the goal of identifying strains capable of extracting REE from solid materials. Over 100 heterotrophic microorganisms were isolated and screened for their ability to produce organic acids capable of leaching REE. The ten most promising isolates were most closely related to Pseudomonas, Acinetobacter and Talaromyces. Of the acids produced, gluconic acid appeared to be the most effective at leaching REE (yttrium, lanthanum, cerium, europium, and terbium) from retorted phosphor powders (RPP), fluidized cracking catalyst (FCC), and europium-doped yttrium oxide (YOEu). The Acinetobacter isolate, BH1, was the most capable strain and able to leach 33% of the total REE content from the FCC material. These results support the continuing evaluation of gluconic acid-producing microbes for large-scale REE recovery from recyclable materials.INTRODUCTIONAn enhanced recovery, substitute, reuse or recycle paradigm is important for balancing the supply and demand of critical materials (DOE, 2011). The recovery of rare earth elements (REE) from recyclable materials is an important component in this model. REE are used in a variety of modern products. For example, neodymium, europium, terbium, dysprosium, and yttrium are important for applications such as permanent magnets, lamp phosphors, rechargeable batteries, etc. (Binnemans, Jones, Blanpain, Van Gerven, Yang, Walton, & Buchert, 2013; DOE, 2011; Graedel, Harper, Nassar, & Reck, 2013). Cerium and lanthanum are used in glass polishers and additives in fluidized cracking catalysts (FCC)."

Jan 1, 2016

By Fulchand Shende

Around the world many potash mines experience brine inflow problems. The presence of brine in underground excavations may induce structural and stability problems. A study has been carried out to simulate the effect of brine on the performance of pillar support. The testing program consisted of loading potash specimens in a creep frame, and simulating inflows by continuously pumping brine into an experimental cell. Brine temperatures and load conditions were varied to simulate several mining and inflow conditions. Specimens were fitted with acoustic emission transducers to monitor energy emissions during an eight-hour test duration. Samples of brine were also collected to provide K+ and Na+ concentration data necessary for an accurate assessment of the dissolution process. Test results indicated that dissolution rates are highly dependent on brine temperature and load conditions. Loads approaching 50% UCS tend to generate very high rates of energy emissions, often leading to the failure of the simulated pillars. This study demonstrated that acoustic emission could be effectively used for predicting the performance of pillars when exposed to inflow brine.

May 1, 2001

By Bennett McLaughlin, Gille Brousseau, John F. Cook

"La Mine Bousquet commenced operations in October 1979. Mining has been by underground methods from two main zones which dip steeply to the south , Sub-level stoping methods with following fill are used.The orebody and immediate country rocks are sericitic and highly schistose. The intensity of schistosity varies significantly and poor ground conditions prevail, especially within the orebody,Initially few mining problems were encountered but in May 1981, significant damage occurred. A system of stabilizing pillars was introduced with improved support systems. Predevelopment in ore and pre-drilling of blastholes were reduced with extra footwall development.Damage has continued to occur on a regular basis particularly during the spring thaw. Generally, the adverse conditions have been successfully overcome.IntroductionMost of the mining problems that have been experienced at Bousquet have been caused by poor ground conditions . This pa per describes these conditions, considers the cause and describes the ways in which the conditions have been dealt with . Despite the problems, Bousquet is a successful operation which in 1983 produced 95,000 ozs of gold from 514,000 tons of ore."

Jan 1, 1985

By Yuki Tsunazawa, Sho Fukui, Chiharu Tokoro

"A milling process is one of the important unit processes in mineral processing. In the milling process, the control of particle size distribution is necessary for the later physical separation process. Since the milling process is strongly affected by the equipment designs, operation conditions and raw materials, the control for particle size distribution of milling products is mainly based on empirical rules. Recently, the discrete element method (DEM) has been widely used as an effective tool to investigate the behavior of grinding media. Although the behavior of grinding media can be accurately simulated, it is not well-established the way to predict particle size distribution after milling by the DEM simulation.The objective of this study was to develop a new method to predict particle size distribution in ball milling using the DEM simulation. To predict particle size reduction, a correlation between experiments and the simulation was investigated in various operation conditions, that is, wide range of the rotation speed and the filling ratio of grinding media. In experiments, after lime stone was ground, the average and variance of particle size distribution were evaluated using some kinds of distribution equations. In the DEM simulation, direct simulation of particle disintegration in milling process is generally very difficult because of huge computational load. Therefore, collision energy between grinding media balls orgrinding media ball and wall was used as a factor of particle disintegration.As a result, a good correlation between experiments and simulation was obtained. In addition, the particle size distribution in ball milling could be predicted using this correlation. Therefore, these results indicated that the use of the correlation between experiments and the DEM simulation was an effective approach of predicting the particle size distribution in milling process."

Jan 1, 2016

By A. A. Burgoyne

"The McDame chrysotile asbestos deposit located near Cassiar in northern British Columbia isfound at depth and on trend to the southeast of the currently mined open-pit Cassiar asbestos deposit. The ultramafic rock hosting the McDame is serpentinized peridotite of the Upper Paleozoic Sylvester Group contained in an ophiolitic sequence preserved within a lower thrust sheet of the Sylvester Allochthon. The Sylvester stratigraphic package is a series of thrust slices composed of argillite, tuff and volcanic flows, diorite and serpentinite. Contacts between units are often fault-controlled.The McDame asbestos-bearing ultramafite is considered to represent a separate interleaved fault-bounded slice of rock distinct from the Cassiar asbestos deposit.Asbestos mineralization of the McDame deposit was discovered in /978. Exploration during /980 and /98/ focused on extensive underground drilling of the deposit and in /983 on geological mapping, airborne and ground magnetic surveys. In /984 a 622.5 m borehole was drilled with a 242 m intersection of McDame ultramafite of which the lower 15/ metres contain potentially economic chrysotile asbestos. The McDame deposit averages 90 m thick, trends north-south, dips easterly and plunges southeasterly. The deposit is estimated to contain geological reserves in the order of 62 million tonnes containing asbestos fibre similar in value to the Cassiar deposit.The McDame is considered a major world-class asbestos deposit. A decision to develop and mine the deposit will require further substantial underground exploration and evaluation. A + 1200 m exploration adit driven to the hanging wall of the deposit was undertaken in 1985 in anticipation of bulk sampling and diamond drilling in 1986."

Jan 1, 1986

By J. E. Udd, L. B. Geller

"Responding to requests by the Canadian mining industry and the mine regulatory authorities, the Canada Centre for Mineral and Energy Technology (CANMET) undertook a major research project on evaluation of wire rope testing in 1986. The objectives were to document, analyze, and clarify - in basic operational terms the reasons for ongoing mine shaft wire rope failures that occur despite mandatory non-destructive testing (NDT) with electromagnetic (EM) instruments on a routine basis.The project&apos;s investigative scope and depth was unprecedented. It could not have been successfully completed without the wholehearted cooperation of industry, research organizations, and mine-inspectorates at both national and international levels.The project&apos;s goals were attained. II was shown that, at present, the problem areas in Canada are oj a human , rather than of a hardware-related nature. Consequently, the principal recommendations are concerned with a more widespread, more uniform and thorough operator training and certification process at industrial and regulatory levels. Secondary suggestions concern areas of hardware-related improvements.In this paper an up-to-date general overview is given of the major project results. A n extensive reference list is also provided of papers that contain all relevant documentation in detail."

Jan 1, 1992

By J. G. Cullain

In conjunction with the over-all goals of energy conservation at Inco Metals Company, a program of improvement in compressed air utilization was established. Air flows were monitored and compared to calculated requirements to establish efficiency by area. With the cooperation of area management, measures were implemented to reduce nonproductive usage. At the operation, annual savings in power consumption alone were 80,000 dollars. The program is being extended to other mine areas within the Division.

Jan 1, 1979

By D. Bois, F. P. Hassani, M. Hossein

"A growing environmental awareness hos prompted the mineral industry to seek innovations in waste management and technology. It is estimated that over 500 million metric tonnes of solid waste each year are rejected by the Canadian mineral industry. This waste hos to be disposed of in the most environmentally and economically acceptable manner.An extensive study has been conducted to estimate the cost of implementing total tailings fill from a waste disposal point-of-view as an alternative to large-scale surface disposal of tailings. The cost of waste disposal at the surface (tailings pond), and underground (total tailings fill) for three Canadian mines which have taken part in Quebec Mine Survey conducted in 1992 are analyzed. Surface disposal is the most economical and common method of mine waste disposal in Canada. Total tailings backfill as a method of waste disposal is technically feasible but cannot be regarded as more economic than surface disposal in all . It is important to remember that while surface disposal costs are rising, due to tighter legislation and more environmental pressure on governments; the costs of preparing and placing total tailings backfill is still falling as the technology improves."

Jan 1, 1994

By P. Chollet, A Constant

THE RESULTS of a previous investigation ( 1) on the work-softening of some heat-treated steels have led to the conclusion that the occurrence and intensity of the phenomenon is possibly governed by the work-hardening capacity of the material, and the relative amount of retained austenite. The first assumption is compatible with Polakowski's theory (2) that the absence of work-softening, in steels quenched and tempered at relatively low temperatures, may be attributed to the high rate of work-hardening which compensates for, and even out-weighs, the loss of internal energy associated with the simultaneous rearrangement of the original system of internal stresses. Indeed, Polakowski first considered the work-softening as a manifestation of a partial release (by cold-working) of the latent strain energy stored in

Jan 1, 1962

By Henry Smith, Stu Brown

"The Williams Mine is Canada&apos;s largest gold producer, with annual production of some 500 000 ounces of gold from two million tonnes of ore. Highly mechanized and automated underground mining practices are utilized at the property in order to help achieve high levels of productivity and the most cost-effective mining possible.Planning and design parameters for the underground ore handling system at the Williams Mine are described in this paper. Particular reference is made to the considerations that were built into the system to provide maximum operating flexibility through the use of multiple orepass systems, portable low profile jaw crushers, underground conveyors and automated hoisting equipment.IntroductionThe Williams Mine is situated in the Hernlo area of northwestern Ontario, approximately 40 Ian east of the town of Marathon (Fig. I). It is operated by the Williams Operating Corporation, which is owned equally by Teck Corporation and Corona Corporation, and is one of three adjacent properties forming the HernIo gold camp.The mine commenced operation in October 1985 at a nominal production rate of 3000 tpcd. Through an ongoing capital development program, winch was completed in late 1989, the production rate at the property was increased to its current level of 6000 tpcd. This paper describes the mine planning process and the evolution of current mining strategies with particular reference to the underground ore handling system .HistoryGold mineralization was discovered in 1944 in the Hemlo area of Northern Ontario, near the north shore of Lake Superior. A year later, 11 claims were staked over the showing and subsequently patented by the late Dr. Jack Kerr Williams.Over the next 35 years, other claims were subsequently staked, explored and abandoned in the immediate area of the 11 patented claims . In 1980 a predecessor of the Corona Corporation acquired claims adjoining the Williams property to the east. Drilling on this claim group started early in 1981 and intersected the Hemlo orebody in May of that year. In December 1981, Corona Corporation entered into an option agreement with Teck Corporation to explore and develop the property.A drilling program by LAC Minerals on the II patented claims discovered the Williams orebody in March 1982. The mine started production in 1985, pouring its first official bar of gold on December 6 of that year. Corona Corporation was awarded ownership of the Williams Mine conclusively by a decision of the Supreme Court of Canada on August 11, 1989. The court&apos;s ruling ended a legal dispute with LAC Minerals over the property initiated eight years earlier."

Jan 1, 1991

By Chia-Chi Chiu, Meng-Chia Weng, Tsan-Hwei Huang

"This paper proposes a biconcave shape bond model for the distinct element method (DEM) to simulate cementation between two circular particles in geomaterials. Rather than an original parallel bond model between particles, the proposed model adopts the more realistic shape of cementation and considers the elastic response of cementation under external loading. The stress field and force-displacement relationship of the biconcave shape bond is based on Dvorkin’s theory, and three modifications are adopted: (1) A superposition method is applied to improve the correctness and symmetry of the stress field, and it also provides a method of addressing the status when both connected particles rotate; (2) To simplify the input parameters, the tangential movement is replaced by the normal deformation and rotation between particles; (3) To accelerate the calculations, variables are extracted in analytical procedures, which provide an efficient method for applying the bond model with only one matrix inversion. With these three modifications, the new biconcave shape bond model is created.To assess the validity of the proposed model, this study compared the elastic deformation in a single bond with an elastic analysis performed using the finite element method (FEM). After verification of the proposed model, a series of sensitivity analyses was performed to explore the effect of bond shape and the differences from the parallel bond model. For a single bond, the results showed that a biconcave model can represent the mechanical behavior of a biconcave shape bond and is effective with different bond shapes. The stress fields calculated by the biconcave model were more similar to the FEM results than those obtained using Dvorkin’s theory. The width and thickness of a bond have a considerable effect on its stiffness, and the variation of thickness decreases with the width of the bond. In addition, the required parameters can be acquired directly from real bond material rather than using the back analysis procedure for parameters.The biconcave model was further implemented in DEM software Particle Flow Code 2 Dimension to certify its applicability in geotechnical engineering. Using this model, a series of uniaxial compression test simulations was performed to analyze the macroelastic responses of specimens. The results showed that the macrotangential elastic modulus and Poisson’s ratio had a regular tendency, and they agreed with the stiffness variation in a microbond. This finding can assist in determining correlations between microand macroproperties and provides an innovative method for simulating the behavior of cemented granular material."

Jan 1, 2015

By D. H. Wilson

"This paper examines the increasing need for mechanical-electrical people within the industry and some of the reasons why such a shortfall exists. It is suggested that, in part, it is image related. The present industry-education relationship in addressing the situation is examined and some thoughts are expressed on how these may be built on, in order to help solve the problem of attracting people to this critical area.IntroductionAs a long-time proponent of plant engineering and maintenance as a management function, I would like to review the progress made by the industry/ educational approaches in satisfying the needs in that area. In doing so, I would like to make the following points:1) that there has been an accelerating shortfall of mechanical-electrical people relative to the needs of the industry;2) that the condition will probably get worse before it gets better; ,3) that the past industry I educational approaches to alleviate the problem have met with limited success; and finally4) I would like to review some of the things being done and consider how these efforts might be extended."

Jan 1, 1981

By Francois Charette

Corrosion is a significant factor affecting the capacity and working life of ground support. The paper explores a relatively simple method to predict the load capacity of a support system using a Monte Carlo stochastic approach. The analysis uses published field data on existing ground support to evaluate the applicability of the method and its predictive performance. Discussion on corrosion rates found in the field and predicted from laboratory measurement is provided.

Jun 1, 2012

By Mihaita Matei

An adaptive approach to control the deformation in tube hydroforming process is presented. This requires: the use of an existing non-linear FE software (ABAQUS) that incorporates a user material model (VUMAT), the development and implementation of an adaptive control strategy to coordinate the internal pressure and the axial load so as to prevent fracture and wrinkling failures (knowledge-base controller) and the application of the developed adaptive simulation approach for finding the optimal loading path required to hydroform a defect-free part with as uniform thickness distribution as possible (user&apos;s load subroutine (VDLOAD). In order to validate the approach, the case of conical hydroforming and the case of bending followed by hydroforming component is discussed.

Jan 1, 2011

By G. E. Agar, J. J. Barrett

"Traditionally, batch bench-scale flotation tests have been used for evaluating flotation reagents by comparing the results of tests done with various additions of the reagent in question. Usually, comparisons are made of the concentrate grade and recovery or some figure of merit involving an empirical combination of both. In some cases, statistical methods have been used to make the comparison and even to identify optimal combinations of reagents.None of the preceding technology utilizes the fact that flotation separations can be described by relatively simple kinetic equations that will serve not only to quantitatively describe the influence of a reagent, but will also aid in designing an optimal separation procedure. Examples of the use of a first-order rate equation for evaluating the impact of a reagent addition and for optimizing the reagent addition are given.IntroductionThe classical method of evaluating flotation reagents is to conduct batch bench-scale tests while varying one factor at a time. Some of the shortcomings of this technique have been pointed out and statistical design and evaluation of experiments has been advocated. Although the statistical approach is superior to the one-at-a-time method, it still is dependent on the results of a batch test conducted for a specific duration.That flotation is primarily a rate process than can be described by a first-order rate equation has been recognized for a long time, but the application of this knowledge to the evaluation of reagents has received little attention. In this work, it is demonstrated how the parameters of the first-order rate equation can be utilized to evaluate the influence of reagents on flotation."

Jan 1, 1983

By Yue hua Hu, Wei Sun, Pan Chen, Li Wang, Runqing Liu, Central South University

"The flotation separation of muscovite from quartz was investigated using mixed sodium oleate/dodecylamine (NaOL/DDA) collectors. The flotation experiments were conducted on single minerals and their collecting performances were studied by means of adsorption amounts and molecular dynamics simulation. Flotation results show that muscovite presents good floatability while quartz exhibits poor floatability in alkaline condition. Adsorption amounts show that both NaOL and DDA can absorb onto surfaces of muscovite and quartz in presence of mixed surfactants. Molecular dynamics simulation indicates that DDA plays an important role in the adsorption of mixed surfactants on these two mineral surfaces. The molecules of mixed NaOL/DDA are arranged in a rigid and well-ordered packing on muscovite (001) surface. Only a few DDA adsorb on quartz directly, and rest DDA and NaOL molecule exist near by the quartz surface, forming a hydrophilic cylinder-like structure. This study may provide guidance for the flotation mechanism and application of mixed anionic/cationic collectors.INTRODUCTIONIn the past decades, there has been an ever-increasing demand for muscovite (KAl2(Si3Al)O10(OH)2) because of its potential applications in cosmetics, construction and metallurgy industries (Barlow & Manning, 1999). Besides, muscovite is an important carrier for some rare metals, including vanadium, titanium and lithium (SsuerrN, 1979). Quartz (SiO2) occurs as the main gangue mineral in muscovite ores, which results in a low purity of muscovite and limits its wide applications. Therefore, there is an urgent need for the beneficiation of low grade muscovite ores. Many studies remove quartz by screening and gravity separation in virtue of their differences in shape, hardness and density. However, these methods undergo poor efficiency in case of small particle size (below 50µm) of muscovite and quartz (Liubakka, Sullivan, Lamphere, Corradi, & Dykhuis, 2011; Santos, Franca, & Ogasawara, 2011)."

Jan 1, 2016

By Eiichiro Mizushima

Catalyst systems comprising (Ph3P)AuCH3 and acid co-catalysts were found to be highly efficient for hydration of alkynes to give ketones. Methanol was the best choice of solvents. Introduction Hydration of carbon-carbon unsaturated bonds is one of the environmentally benign routes to the carbon-oxygen bond formation. Hydration of alkynes forming carbonyl compounds, an important variation in this category, is a well known reaction which has been extensively studied. The reaction by acid-catalysis is the most conventional method, while it is applicable only to electron rich acetylenes to obtain satisfactory yields (1,2). The hydration of simple alkynes usually requires another catalyst (co-catalyst), typically a mercury(II) salt (3), which is inconsistent with the guiding principle of Green Chemistry (4).

Oct 1, 2003