Search Documents

By Yihan Liu, Jintao Zhang, Chen Xiao, Xiaomeng Zhao, Guanglei Song

To estimate the performance of the inert anode materials based on NiFe2O4 spinel ceramic during it used for aluminum electrolysis, we investigated the wetting process of cryolite molten salt which is in composition of industrial aluminum electrolysis with carbon anode and NiFe2O4 based cermet materials, by means of determination the interface wetting angle between the molten cryolite electrolyte and the solid anodes interface. The results show that the wetting angle between the electrolyte and carbon anode is larger than 90 angulation, this means that they basically can not wetting; however the nickel ferrate spinel ceramics behaves much better. In regard to the NiFe2O4 matrix materials, their initial wetting angles is 76.9. The initial wetting angles for 1.0wt%MnO2, 2.5wt%TiO2 and 0.5wt%V2O5-doped samples are respectively 56.86°, 52.98° and 51.93°. However, after 50s later, all the wetting angles came down below 15°.

Jan 1, 2015

By C. L. Lewis

"The development of computer process control at the Lake Dufault concentrator is reviewed and the on-stream X-ray analysis -computer system is described briefly. Some applications of the computer in metallurgical process control are described.The computer sequences slurry sample streams to the analyzer and translates the analytical results from voltage signals to elemental percentages. The required flotation reagent flow rates are calculated from analyses and mill-feed tonnage rates and the reagent feeders are set automatically to provide such flow rates. X-ray calibration time has been reduced from about 45 minutes to 15 minutes by the use of a computer program. Metallurgical and operating personnel have acquired the ability to program the computer and have extended the system capability to allow the calculation of recoveries, averaging of mill data, application of ore specific gravity in grinding control, control of oxidized ore flotation and the development of an economic recovery program."

Jan 1, 1971

By J. J. Jonas, G. R. Stewart, N. Pokutylowicz, S. Yue, R. Varano, A. Elwazri

Differing thermal histories in and around a weld can lead to differences in grain size, phase composition and morphology of precipitates; mechanical properties will vary accordingly. Hardness testing gives limited information and the machining and testing of tensile and/or impact specimens that would reveal these variations (which may occur over very small distances) is not practical. Therefore, in this investigation, shear punch testing was applied to measure the variation in the room temperature mechanical properties of a welded pipeline steel.

Jan 1, 2005

By G. F. Trainor

At the Canadian Natural Resources Limited (CNRL) Horizon Mine they use Wenco International Mining Systems Ltd (Wenco) Fleet Management System to monitor and control their production fleet with the goal of increasing operator productivity and safety, and raising dispatcher awareness and control. Amongst the broad productivity goals CNRL wanted to achieve with help from the system was a very specific need to blend ore at the truck level. CNRL uses 25m x 25m block geological model information to represent their complex ore body. Wenco's High Precision GPS application, BenchManager provides precise graphical actual-vs-design operator feedback and system integration. Together the two companies advanced the BenchManager product to meet CNRL's needs by using live camera feeds to compare activity with data collection that ultimately lead to changes in the algorithm to include enhanced GPS indicators and the support of a GLONASS assisted solution generating distance and bearing information.

May 1, 2011

By John Hartlen

"The 19th century was an ""age of gold"" and Nova Scotia experienced its share of early gold rushes. Gold mining activity in the province was focussed into three ""rushes"" which occurred, approximately, in the 1860s, 1890s and 1930s; a total recovery of 1.1 million oz. Au has been recorded. The purpose of this note is simply to chronicle the technical development of gold mining and processing in the province and to comment briefly on the recently renewed interest in this precious metal. The first public discovery of gold in Nova Scotia was made by a farmer in 1860 at Old Tangier or Mooseland, and this find sparked the province's first gold rush. The mining and milling methods of the 1860s were ingenious. Initially, arrastras, crude stone-hewn grinding mills, drawn by men, mules or horses, were widely used. Nova Scotia's first conventional stamp mill was installed at Mooseland by 1862; it was comprised of four wooden stamps and is believed to have been imported from Scotland. One of the largest waterwheels of the 1860s, reportedly 16 feet in diameter and 8 feet wide with a SO-horsepower rating, was used in the Renfrew Gold District to drive gold stamps. Steam power was also employed, and many of the engines were of native construction, as was the unit at Waverley's Lake Major Company, which had a piston 1 foot in diameter by 12 feet long and was connected to a 16-ftdiameter flywheel."

Jan 1, 1999

By L Munholand, G. Soucy, P. Quintal

This work presents early results from the first study to optimize the hydrodynamics of a Plasma Lift Reactor (PLR). The PLR is designed to break down organic contaminants in aqueous solutions. New experimental results are presented for air/water tests and for plasma degradation of organic contaminants in Bayer liquor. In addition, a multiphase Computational Fluid Dynamics (CFD) model has been developed which predicts the hydrodynamic behavior in the PLR. These results of this work suggest the PLR is effective at reducing contaminants in the Bayer liquor and that the CFD model adequately describes the hydrodynamic flow.

Jan 1, 2005

By B. Ignasiak

Laboratory studies suggest that improvements of coke strength brought about by pre-heating caking coals before carbonization accrue from inadvertent oxidation rather than from other low-temperature changes in the coal mass. Controlled oxidation of highly caking coal, followed by laboratory carbonization, produces cokes which, in terms of a laboratory scale tumble test index, are equivalent to those obtained from prime metallurgical blends. Appropriately formulated blends of exhaustively oxidized and fresh caking coal similarly yield cokes with strength indices comparable to those of cokes made from the same coal after oxidation under optimum conditions.

Jan 1, 1979

By D. Markwart, B. Volk

Anode effects are a phenomenon of the aluminium electrolysis process which produce potent greenhouse gases called PFCs (CF4, C2F6). With concerns surrounding global warming, and increasing regulation of GHG emissions, anode effects have become a significant sustainability issue for aluminium producers. In modem smelters, sophisticated computer control and automated alumina feeding systems allow for very tight control of the alumina concentration in the electrolyte and thus very low anode effect frequencies. Older smelters, however, do not have these systems and must either invest heavily to obtain them, or find other, innovative ways to reduce anode effect frequency. This paper will present the integrated approach to anode effect reduction used in the Vertical Stud Soderberg (VSS) potlines at Kitimat Works. Through an innovative combination of simplified signal analysis, modified alumina feed control logic, anode effect prediction, and anode effect prevention using a pager based communication system, Kitimat W arks has been able to make significant reductions to its anode effect frequency.

Jan 1, 2006

By Lex L. Udy

External-detonation-generated plasmas, highly ionized zones of reacting material ejected from the surface of detonating explosive charges, are shown to be the cause of channel desensitization, i.e., the self-quenching of a detonating explosive column loaded in a borehole with an air annulus between the explosive and the borehole wall. The effects of this phenomenon on several explosive compositions and types are demonstrated and discussed. The explosives tested include aluminum-sensitized and explosive-sensitized slurries, ANFO, liquid explosives and dynamites. Various techniques are described that can be used to reduce or eliminate the plasma effect.

Jan 1, 1979

By Wei Yun-Jie

Columnar jointed basalt is a fractured rock, with a lot of small spacing structural planes and poor integrity of the rock mass. On the basis of the comprehensive study of the columnar shape of Columnar joints, rugosity of the fracture surface and the chemical composition of basalt, columnar joints of Bai hetan dam area were formed as a result of the cooling and shrinkage effect of magma. Columnar joints basalt are mainly chlorite, kaolinite, epidote, tremolite chemical reactions and the content of columnar joints are mainly chlorite by slice identification and chemical analysis. Columnar joints basalt showed high uniaxial tension test, low coefficient of friction and high cohesion by indoor physical and mechanical test. Columnar joints rock mass showed high strength and large deformation by field shear test and deformation test. Columnar joints basalt can be used directly as a foundation of dam as long as we follow the rules and reduce disturbance strictly.

May 1, 2009

By S. Komar Kawatra, Youlian Zhou, Joseph A. Halt

"Bentonite clay has been the most common binder for iron ore pellets. Although bentonite increases pellet strength and durability, it has several disadvantages. For example, its use increases the cost of pellets and decreases pellet purity due to its composition and the higher levels of flux required to meet basicity limits. Several new types of binders have been proposed to replace clay. The binders include starch, modified humic acid (MHA), and dispersants. These binders were used to pelletize a magnetite concentrate from the United States. Typical doses of each binder type were 0.05-0.1 % starch, 0.5-0.75 % MHA, and 0.05 % dispersant. At these doses, the pellets exceeded the minimum recommended values for wet drop, dry compression strength, and fired compression strength. Pellets made with the MHA and dispersants had the lowest abrasion rates of the new binders, and were comparable to pellets made with bentonite clay. In this paper, we compare the new binders, considering pellet quality and the advantages and disadvantages of each binder type.INTRODUCTIONIron ore pelletizers need binders in order to make good quality iron ore pellets. The typical binder is bentonite clay, an alumino-silicate material. Bentonite increases the ballability and strength of iron ore concentrates, but reduces pellet iron grade and reducibility. As high quality bentonites can be expensive to ship, low quality bentonites are often used at significantly higher doses – this reduces iron grade and reducibility even further. Thus, several new types of binders have been proposed to replace bentonite clay.In this paper, we present several new binders for iron ore pellets: starch and modified humic acid (MHA). These have been tested alone and in mixtures with dispersants, or else with bentonite clay. Starch, MHA and their mixtures are briefly described below."

Jan 1, 2016

By Denni Hoffmann

"Banded iron formation rocks associated with massive sulfide lenses in the Broken Hill Pb-Zn-Cu-Ag deposit in the Namaqualand Metamorphic Complex, South Africa, were investigated with respect to the geochemistry of manganiferous silicate-rich bands. Two common varieties of these are: amphibole- and garnet-rich iron formation bands. The results reveal that the former are enriched in Fe, Mg, Cu, Co and S. The garnet-rich bands are enriched in Mn, Ca, P, Pb and Ba with significant detrital contamination of Ti, AI, Zr, Cr, Y, V, Ni and Nd.The silicate-rich bands have compositions, in terms of, Si/AI, SilFe, FelMn, LalCe and Co/Zn, comparable to submarine chemical sediments which precipitated from hydrothermal fluids. The garnetand amphibole-rich bands are interpreted as ""evolved"" and ""immature"" hydrothermal sediments, respectively. The latter resulted from rapid precipitation after exhalation, whereas the former had a longer residence within sea water. The silicate-rich bands both exhibit increasing Mn/(Mn+Fe) fractions, which are consistent with a variation expected from proximal to distal depositional settings. The prevalence of garnet-rich bands over amphibole-rich bands is interpreted as the result of injection of hydrothermal fluids from a single vent situated along the northwest margin of the Broken Hill deposit."

Jan 1, 1994

By J. F. Perreault, J. Paraszczak

"The profitability of an underground mine depends to a great extent on the production cost.Random equipment failures and their consequences have significant influence on the total operating cost of a mining system. Having this in mind, a reliability study has been initiated for loadhaul- dump machines in an underground mine. The main purpose of this study is to identify the critical machine subsystems, determine their failure pattern and help work out an effective maintenance strategy. In the first part of this study, the failure data of diesel powered LHDs, gathered during an I8-month period have been analyzed. For the purpose of the analysis, the machines have been treated as systems comprising seven subsystems connected in series. The most critical subsystems, i.e. electrical and hydraulic, were further investigated, and analyzed by graphical and analytical methods. Different failure distribution models were applied and discussed. Basic Defmitions and ConceptsIn order to avoid confusion, several terms used in this paper are defined below, as compiled by O'Connor (1991). The acronymsBS and MIL-STD stand respectively for: British Standard and US Military Standard.Failure: the termination of the ability of an item to perform a required function (after BS 4778).Time Between Failures (TBF): the length of time between two consecutive failures.Observed Mean Time Between Failures (MTBF): For a stated period in the life of an item, the mean value of the length of time between consecutive failures computed as a ratio of the cumulative observed time to the number of failures under stated conditions (after BS 4778).Maintenance, Corrective: The actions performed, as a result of failure, to restore an item to a specified condition (after MIL-STD-721 B).Maintenance, Preventive: The actions performed in attempt to retain an item in a specified condition by providing systematic inspection, detection and prevention of incipient failure (after MIL-STD-721B)."

Jan 1, 1994

By M. Lytle

"The Corbin area of southeastern British Columbia has been a coal mining area since 1908. Byron Creek Collieries Ltd. Has operated its Coal Mountain Mine in this area from 1974 until the present. In February 1981, this company was purchased by Esso Resources Canada Ltd.Coal Mountain is structurally complex and standard computer algorithms are not applicable to model the overturned synclinal structures and faulted bedding surfaces. This paper discusses two approaches used by Esso Resources staff to model the geology of Coal Mountain.The first approach projects digitized cross-section data along trend to develop a large data base which correctly approximates the shape of the structure. The spatial orientation of the structure is corrected by merging the generated data set with drill-hole data. The second approach uses digitized cross-section and bench-plan geology to generate a block model of the coal reserve.HistoryThe Coal Mountain Mine, also known as the Corbin Mine of Byron Creek Collieries Ltd. is located 24 kilometres south of Highway 3 in southeastern B.C.In 1905, two American businessmen recognized the coal potential of the area during a horseback tour. The two businessmen, D.C. Corbin and E.J. Roberts, formed the Corbin Coal and Coke Co. to mine and market coal from their newly acquired 6075 hectares of coal licenses. By 1908, the town of Corbin was under construction, a 22.4-km rail spur was constructed from the mine to the main CPR line and the first underground mine began to produce coal. An open-pit operation was also developed at the 1828-metre elevation using a steam shovel loading into rail cars. The company operated continuously until 1935, when a lengthy strike forced suspension of operations.In 1943, the Consolidated Mining and Smelting Company Ltd. (now known as Cominco Ltd.) operated two surface mines to produce coal for its smelters at Kimberley and Trail, B.C. This operation ceased in 1948."

Jan 1, 1982

By G. Vibert Douglas

It has long been recognized that there are considerable difficulties connected with the physical and chemical explanation of shoots of ore. The literature of Mining Geology has frequent references to this subject; but the reasons given for the actual location of primary ore-shoots have been very tentative. In practice, the geologist or miner depends to a great extent on sampling and assaying to determine the boundaries of profitable ore within the mineralized zone. An ore-shoot is a portion of a mineralized zone which has a sufficient concentration of valuable minerals to make it ore. Ore deposits have been classified according to many schemes. There are classifications based on morphology and on genesis. However, it is also possible to classify hypo-gene hydrothermal ore-bodies in terms of ore-shoots or vice versa. A.-Ore-deposits in which the whole of the mineralized zone is ore, which is the same as saying that the ore-shoot extends throughout the mineralized zone. An example of this type of deposit would be the pyritic mineralization of Rio Tinto. B.-The second type would comprise those deposits in which the ore-shoots bear some relation to the geological structure of the area: all deposits in which 'bonanzas' occur in folds in the zone, at the intersection of veins along certain fault (or joint) features and other such controls. There are a great many examples of this type: (a) The Rhodesian copper lodes, where Bancroft and Gray have pointed out the association of the shoots of ore with drag folds. (b) A similar association has been pointed out by Faribault for some of the gold veins of Nova Scotia, e.g., Mount Uniacke. (c) The great bonanza of the Comstock lode in Nevada. C.-Deposits in which the localization of ore has been effected by the chemical character of the wall-rock. Examples of this type are the Fahlbands of Scandinavia, and the 'indicator' deposits of Ballarat, Australia. D.-Lastly, deposits in which there is apparently no structural and no chemical control.

Jan 1, 1934

By G. Danko, C. Lu

"High temperature and humidity at the working negatively affect safety and health in deep and hot underground mines. It is necessary to predict during design the dynamic changes in temperature with heat and moisture emitted into the mine ventilation-thermal-humidity (VTH) system from various sources such as auto-compression, wall of strata, mining equipment and workers. Currently available mine ventilation and climate models are either furnished with a simplified, step-change-type (SCT) model for thermal solver (such as in Climsim, VnetPC, Minevent, MFire, etc), or with more advanced models to account for the “thermal history effect” (also known as thermal flywheel effect), such as in Ventsim and MULTIFLUX. The goal is to quantify the modelling error caused by the lack of variable thermal history component in the SCT model. Two models are compared: one with and one without the thermal history component in long, single airway examples with long-term climate simulations for 20 years assuming an input air temperature with daily variation. The examples illustrate the magnitude and the time-lag phase of the variation of the modelling errors with space, time and model conditions. Large errors are shown in the order of +14°C and –7°C errors, persistent for long time periods, up to 20 days in one example.INTRODUCTIONIt is important to predict the heat and humidity distributions during the design of hot and humid underground mines for the safety and health of the workers. The feasibility of extracting a rich deposit in great depth may depend on the extent of ventilation and mine climatization for maintaining an acceptable working environment. The cost of ventilation and cooling may be substantial, up to 40–50% of the total energy cost of mining (Clausen, 2017). The accuracy of model solution is important in view of the low profit margin in mine feasibility for deep and hot mines. Safety and health of the miners, the primary concerns, are therefore inherently connected to finding ever better solutions in simulation methods and ventilation control techniques."

Jan 1, 2019

By J. B. Morrow

Methods of Coal Preparation Fundamentally, the object of coal preparation is to increase, economically, the value of a fuel by making it more suitable to the uses of the consumer. This can be accomplished in three major ways: 1.Screening or sizing 2.-Mixrng or blending 3.-Cleaning By combinations of any or all of these methods we can prepare coal to meet standard specifications-a process of standardization which is the more desirable the more nearly it approaches the unvarying quality of packaged goods, where the package you buy today and tomorrow is the same as that you bought yesterday. It should be noted that it is readily possible to get good cleaning and still have poor preparation because of faulty screening and mixing, and, on the other hand, it is possible to get a passable grade of cleaning, combined with good screening and mixing facilities.

Jan 1, 1931

By M. Rafiee

Indoor physical security, as a perpetual and multi-layered phenomenon, is a timeintensive and labor-consuming task. Various technologies have been leveraged to develop automatic access control, intrusion detection, or video monitoring systems. Video surveillance has been significantly enhanced by the advent of Pan-Tilt-Zoom (PTZ) cameras and advanced video processing, which together enable effective monitoring and recording. The development of ubiquitous object identification and tracking technologies provide the opportunity to accomplish automatic access control and tracking. Intrusion detection has also become possible through deploying networks of motion sensors for alerting about abnormal behaviors. However, each of the above-mentioned technologies has its own limitations. This paper presents a fully automated indoor security solution that leverages an Ultra-wideband (UWB) Real-Time Locating System (RTLS), PTZ surveillance cameras and a Building Information Model (BIM) as three sources of environmental data. Providing authorized persons with UWB tags, unauthorized intruders are distinguished as the mismatch observed between the detected tag owners and the persons detected in the video, and intrusion alert is generated. PTZ cameras allow for wide-area monitoring and motion-based recording. Furthermore, the BIM is used for space modeling and mapping the locations of intruders in the building. Fusing UWB tracking, video and spatial data can automate the entire security procedure from access control to intrusion alerting and behavior monitoring. Other benefits of the proposed method include higher accuracy and robustness, more complex query processing, and interoperability with other BIM-based solutions. A prototype system is implemented that demonstrates the feasibility of the proposed method.

Aug 1, 2013

By Garston Blackwell

Abstract - During geostatistical estimation of block grades, the kriging process produces a measure of error, the kriging variance or the kriging standard deviation. Estimation of the block error depends on the semi-variogram model for a deposit, which reflects fundamental characteristics of a deposit such as (1) nugget effect, (2) range of influence of grades, (3) different local spreads of data as a function of average grade (proportional effect), (4) nested structures, and (5) underlying anisotropies in the data; this model may be affected by sampling or assaying limitations, however. Because the kriging error incorporates so many features of both the deposit and data to be used for estimation, it may offer a substantial improvement on block classification over traditional procedures such as data density. Practice indicates that the relative kriging standard deviation (RKSD) is particularly useful for block classification in measured, indicated and inferred categories. Plots of RKSD in plan and section also can be used to demonstrate where extra drilling and sampling would be most advantageous for upgrading the class of some blocks. Moreover, the use of grade and RKSD filters can show where material near cut-off grade is poorly defined, indicating sampling target areas to improve block classification in the vicinity of the ore-waste boundary.

Jan 1, 1998

By H. C. Gunning

Introduction Considerable attention has of late been attracted to the area surrounding Nimpkish lake, on northern Vancouver island, by the discovery of important rich copper deposits. In less than two years some 200 mineral claims have been staked in a small area, and at least two groups have very promising surface showings. During the summer of 1929, the writer spent one month investigating the general geology and mineral deposits of the region, and, although no detailed work has as yet been done in the field or in the laboratory, the importance of the mineral discoveries and the lack of geological information available to the public warrants a preliminary paper on the district. The district is, from a mining viewpoint, very accessible. Boats from Vancouver call at Englewood, in Beaver cove, four times a week. From Englewood, a first-class logging railway, operated by the Wood, .English Company, extends to the northeast corner of Nimpkish lake. The fifteen-mile trip from the north to the south end of the lake is made by boat, two tugs being maintained by the logging company. The whole trip from Englewood can easily be made in one day. The known mineral deposits lie immediately east of the southern part of the lake, four miles or less from the shore. A fair trail, four miles ? long, leads from the lake to the Nimpkish Copper group. Apart from this trail and an old logging railway grade which follows the east side of Klaanch river for several miles, no trails exist on the southeast side of the lake.

Jan 1, 1930