Search Documents

By X. X. Wu, Q. Zhang, R. H. Fan, Y. J. Feng, J. D. Liu, P. Z. Zhao

In the present study, AA6016 automotive sheets with different grain size were fabricated through changing fabricating parameters, and the effects of grain size on the bendability were studied by bending test and optical microscopy. The results showed that the sheet with coarse grains exhibited poor bendability, and some micro-cracks were revealed at the surface of the bending samples. While the sheet with fine grains exhibited good bendability, and the bending samples showed smooth surface. Shear bands on the cross section of bending samples were observed. It was found that samples with coarse grains had more shear bands. These shear bands distributed in bundles, which facilitated the formation of continuous neckings and micro-cracks. However samples with fine grains had less shear bands, which distributed uniformly. The decrease of grain size could not only hinder the formation of shear bands, but also improve the homogeneity of its distribution during bending. On the other hand, refining grains could increase the amount of grain boundaries, which impede the propagation of shear bands. Hence the decrease of grain size could hinder the formation of continuous neckings and micro-cracks during bending, resulting in the significant improvement of the bendability.

Jan 1, 2015

By C. Pichler, S. Luidold, C. Wagner, C. Sagadin, D. Kreuzer

Engineers and scientists have been combating the attack upon refractory materials of molten metals/matte and slags for hundreds of years. The details in many cases are still questionable or at least debatable. The corrosion is a major concern for furnace operators as refractory wear or failures inevitably results in reduced production efficiency and furnace reliability. Also the cost to industry is considerable and only a thorough understanding of all the complexities of the process will help to minimize that cost. One of the critical questions to overcome is the correct selection of refractories for the individual process steps to provide long and predictable refractory life together with high furnace availability. To understand the nature of the reactions involved in refractory corrosion, it is crucial to determine the complex thermo- chemical equilibria of the reactions occurring between the refractory materials and the process phases. A simulation model coupled with commercial software like FactSageTM is demonstrated aiming to understand the corrosion mechanisms between refractories and the molten process phases and draw implications for improving the performance of refractories and refractory lifetime. INTRODUCTION The extraction or recycling of valuable materials, e.g. metals, can be done by two main routes, pyro- and/or hydrometallurgical processing, depending on the chemical behavior of the used ore, scrap or pre-treated concentrate. Sometimes it is also necessary to use both process routes for the extraction or the recycling of valuable materials. In the case of a pyrometallurgical treatment, the usage of refractory materials is inevitable. This is mainly caused by high temperatures, prevailing during processing. The interaction between refractory material and slag, metal or matte leads to different reactions and interactions. As a main result corrosion of the furnace lining (refractory material) takes place. Hence, recurring furnace shutdowns occur for renewing the refractories. This leads to reduced production efficiency. Such refractory lifetimes are between some hours and decades, depending on the processes.

Jan 1, 2019

By A. Iizuka

This study was aimed at separating and recovering arsenic, antimony, and tin from refining byproducts generated in a nonferrous smelter. The target byproduct was a silicate slag containing the above elements. The silicate structure of the slag was destroyed by alkali roasting, which then enabled leaching of arsenic, antimony and tin in solution effectively. Arsenic was selectively leached out by hot water after alkali roasting of the slag, while remained antimony and tin in the residue were leached out by a hot hydrochloric acid solution. However, when the solid-liquid ratio in the leaching solution was increased, hydrous gelatinous silica (gel-like silica) was formed during the hydrochloric acid treatment and filtration became difficult. Therefore, high temperature and high pressure leaching was attempted to improve the filterability of the silica leaching residue. In the high temperature and high pressure treatment, the hydrous gel-like silica was transformed into easily filterable aggregated silica, and thus, filtration became easy. By investigating the neutralization and sulfurization treatment for the obtained hydrochloric acid leachate (second leachate), it was possible to separate antimony and tin. INTRODUCTION This study aims to separate arsenic and recover valuable metals such as antimony and tin from refining byproducts generated in a nonferrous smelter. The target smelting byproduct is antimony-containing slag in this study. In many cases, alkali roasting was adopted as pretreatment for extraction and recovering valuable metals from smelting residues and wastes (Rao, 2006). For antimony-containing slag in this study, one effective method for separating arsenic is to convert arsenic to sodium arsenate (Na3AsO4) by roasting with a sodium compound and then to remove arsenic by hot water leaching. In addition, by alkali roasting, the silicate structure of the slag is destroyed, and effectively alkalizing tin and antimony is accomplished. Then, precipitating and recovering tin and antimony leached into the acid solution are considered possible by sulfurization and neutralization treatments. In this research, we conducted basic studies on the following. 1) Destruction of silicate structure in slag by alkali roasting and leachability of arsenic. 2) Conversion of hydrous gelatinous silica to aggregated silica by hydrochloric acid treatment of residues after arsenic leaching under high temperature and high pressure, as well as leachability of antimony and tin. 3) Separation and recovery of antimony and tin by sulfurization and neutralization treatments of hydrochloric acid leachate. These topics of investigation can support to consider the separation and recovery process of arsenic, antimony, and tin from antimony containing slag.

Jan 1, 2019

By G. Robert Guillet

"Ontario enjoys the advantage of its proximity to the large industrial market of northeastern North America. Together with Quebec and fifteen nearby U.S. states, an industrial base of more than half the total for both countries is provided by a population of 100 million.Mineral fillers such as barite, calcium carbonate, kaolin, mica, silica and talc are of major importance in the manufacture of paper, paint, plastics, rubber, vinyl tile, carpet backing, putty, caulks, sealants and adhesives. Ontario has all of these minerals, but domestic production falls short of demand in some cases, and mica and kaolin are not produced at all.This paper reviews the market and outlines the distribution of the major filler-consuming plants of northeastern North America. It also identifies the principal producers of filler minerals in the United States and Canada.IntroductionOf all the uses for industrial minerals, mineral fillers are probably the least understood. Originally used primarily to add low-cost bulk to a variety of commodities without seriously affecting their properties, filler minerals have become essential components that enhance and extend the properties of their hosts. Hence the term ""extender"" which, for all practical purposes, is synonymous with ""filler"". Today, fillers and extenders are not solely low-cost additives, but ingredients that provide essential characteristics to the products they fill.The major markets for mineral fillers are paint, paper, plastics, rubber, adhesives and floor coverings. But there are many others: putty, pesticides, wire and cable coatings, caulking and asphaltic compounds, oilcloth, wall-paper, joint cements, inks, sealants and many others. Barite, calcium carbonate, kaolin, mica, silica and talc are among the more important filler minerals discussed in this paper, but there are at least a dozen others. And the increasing practice of coating the mineral surfaces with certain coupling agents or metal stearates is constantly expanding the range of characteristics and hence the marketing opportunities.Whiteness, particle shape, fineness of grind and cost are the principal considerations in selecting a filler, but other characteristics such as weight, opacity, hardness and chemical inertness may be dominant considerations in specific applications."

Jan 1, 1987

By M. G. Beukes

"In South Africa most of the large gold mines operate between 1500m and 4500m below surface where reef is accessed initially through a vertical shaft system then via a network of tunnels and mined in either a longwall, sequential grid or scattered mining configuration. Due to the complexity of the ventilation networks used to ventilate these mines and the potential disastrous consequences associated with underground fires, it is of utmost importance that these mines are managed in such a way that underground fires are prevented. However, if they do occur the fires are managed to firstly prevent the loss of life and secondly protect the infrastructure and viability of the mine. The aim of this paper will be to: • Discuss current SA mining legislation regarding underground fire prevention and control. • Examine these fires from a risk management perspective by means of a bowtie assessment. • List and discuss the major Threats and Consequences as determined by the bowtie assessment. • Discuss the various prevention and consequence controls for deep level underground fires. • Examine how to effectively run an emergency control room. From this, a practical way of designing, implementing and managing an underground fire management system is explored. Lastly, the paper identifies new technology and ways of thinking and how these can be used to combat underground fires. INTRODUCTION The orebodies of South African gold mines are generally narrow tabular structures that vary in thickness between 0.8m and 1.2m with an inclination of between 200 and 700. This, coupled with depths of between 1500m and 4500m, as well as the unpredictable geology, creates unique challenges and significantly impacts on mine designs and mining methods. In general, gold bearing reefs are accessed initially through a vertical shaft system then via a network of tunnels and mined in either a longwall, sequential grid or scattered mining configuration (Figure 1). Mining is very labour intensive with very limited mechanisation opportunities and this increases the risk to human life if an underground fire occurs. On 16 September 1986, one of the worst mining disasters in SA mining history took place when 177 mineworkers were killed at Kinross Mine. An acetylene tank sparked flames that swept through the mining tunnel igniting plastic covering on the wiring and the flames also set fire to polyurethane foam. The burning plastic combined with polyurethane and the toxic fumes that filled the shafts caused the miners death. This incident was a stark reminder of the serious consequence that underground fires can have on human life as well as the crippling financial and asset impact for the mining companies. Over the past thirty years, the SA mining industry reduced the number of mine fires significantly by replacing normal timber support with fire retardant treated timber, alternative support systems such as backfill and elongate support and many other fire prevention initiatives. Although the number of fire incidents and number of fatalities due to fires does not show a direct correlation because of various factors, the controls put in place against fires has had an impact on the number of fire and explosion fatalities (Figure 2)."

Jan 1, 2019

By M. W. Bartley

"The Steep Rock iron mine is 141 miles west of Port Arthur, Ontario, and 50 air miles north of the Vermilion iron range in Minnesota. The property lies 27'2 miles north of the village of Atikokan on the south line of the Canadian National railway.The orebodies underlying the bed of Steeprock lake, since de-watered, were known to exist 60 years ago. References to the possibility of iron ore at this location were made in early geological papers and reports. In 1937 the locations of the orebodies were determined by dip-needle surveys, and from 1938 until 1943 diamond and churn drilling were carried on to prove their extent and configuration. It was found that the ore, in addition to being associated with definite types of wall-rock, was controlled by structural features, such as faulting and brecciation. From this geological knowledge the presence of other deposits has been inferred, and these are now being explored and developed.Production at the property commenced in October 1944. During that season 17,000 gross tons of ore was shipped. In 1945, 506,000 gross tons and in 1946, 830,000 gross tons was mined and shipped. In 1946, 164,000 gross tons additional was placed on stockpile for future shipment.TYPES OF 0REBODIES AND MINERALIZATIONThe orebodies at Steep Rock iron mine are tabular. They have an average width of 250 feet, lengths up to 5,000 feet, and persist to known depths of 1,200 feet. They are replacement deposits in brecciated carbonate rock at the contact of underlying pseudo-limestones and overlying volcanics. The ore is composed of hematite and hydrous hematite in the form of goethite, turgite, and limonite. These minerals replaced the brecciated host rocks metasomatically as a result of hydrothermal action. The replacement followed a definite structural pattern along the unconformable contact between the sediments or other rock (now replaced by carbonate) and the volcanics, subsequent to disturbances in the form of minor faulting and shearing. The faulting and shearing provided the channels through which the replacing solutions percolated. It is believed that the late basic intrusions outside the ore zones were genetically responsible for the introduction of the ore-bearing solutions."

Jan 1, 1954

By Robert Cameron, Colin Ashton, John MacNeil, Leo Piciacchia

"The in pit dam construction and utilities relocation, known as the East Mine Corridor Relocation (EMCR) project, was developed to extend the life of the east side of the Base Mine pit by two veal's. This will result in the recovery of an additional 80 million barrels of oil and delay expenditures associated with the opening of the North Mine by two years. To accomplish this, a large in pit earth structure was required to provide a new embankment foundation for relocating a public highway, four powerlines, a natural gas back-up pipeline, a substation, and a conveyor train. This structure would also he required as a temporary dam 10 contain mature fine tails on the west side until mining is completed in the east mine corridor area, that will then be filled with fluid.The in pit dam, known as The Highway Berm, is 2.5 km long, 63 m high and has 42 million m3 of engineered soil added to the already existing end-dumped soil volumes. To complete the design and construction of a structure of this magnitude, in the very short time frame of two-and-a-half years, presented many new challenges. The main challenges faced were: designing while construction was ongoing; designing without the use of clay cores or sand filters; using relatively non-select overburden material; proper dewatering and base preparation; changing from construction of 50 m high spoil piles to a high specification construction operation; compacting lifts with heavy haulers; constructing during the winter; and monitoring movement of the structure with satellites."

Jan 1, 1995

By H. L. Gibson, T. N. Setterfield, J. J. Watkins, R. W. Hodder

"The McDougall-Despina fault set in the Noranda district of northwestern Quebec defines the eastern margin of the Despina cauldron, nested within the district-scale Noranda cauldron. The faults are stratabound in that they displace stratigraphy of the cauldron fill, but do not off-set the cauldron cover. The faults are occupied by dikes that acted as eruptive centers to volcanic members of the cauldron-filling sequence. Measurable displacement across the McDougall-Despina fault set is greater than 750 m, and coincident with post-cauldron volcanism. Feeder dikes cross-cut each other and are typically depleted in Na2O and CaO, and enriched in MgO, K2O, Fe2O3and MnO relative to fresh flows. Economic and subeconomic massive sulfide deposits occur adjacent to the McDougall-Despina fault set at different levels over a stratigraphic thickness of 3000 m. These include the Corbet deposit, the subeconomic D-68 Zone deposits, and the subeconomic stringer zones of South Rusty Hill and Bedford Hill. Numerous copper occurrences and abundant hydrothermal alteration occur in and immediately adjacent to the fault set.The McDougall, Despina, and adjacent, parallel, ancillary faults define a synvolcanic fault set which controlled the location of magmatism, hydrothermal alteration and mineral deposition during the early evolution of the Noranda cauldron. Significant sulfide mineral deposition commonly occurred in proximity to the intersection of the McDougall-Despina fault set with northeast-trending synvolcanic faults. Recognition of synvolcanic faults is therefore a major objective of exploration programs for volcanic-associated massive sulfide deposits."

Jan 1, 1995

By B. Hewitt

Murrin Murrin Operations has not had a successful beginning. Numerous reliability and operability issues many of which are the result of design decisions have been addressed through mechanical and operational changes and the CCD circuit is no exception. The decision to install, the installation and the results of the CCD1 rake-lift mechanism and feedw ell dilution system are discussed in this paper. The installation was justified on improved operational robustness and an increase in the in the underflow density of 1% (per cent w/w). At approximately the same time process modifications in the solution neutralisation circuit were implemented and these changes altered the rheology of the slurry reporting to CCD1. Since the modifications to CCD1 and the solution neutralisation circuit, the CCD circuit has averaged a 2% improvement in the circuit underflow density. The CCD1 modification was completed on time and mechanically has performed well. From a risk point of view, the central rake-lift and Turbodil® dilution system add a degree of freedom and robustness to CCD1 operation that has extended the range of operational confidence. In this respect, the modification has been a success and is complementary to solution neutralisation improvements.

Jan 1, 2004

By E. Larsen

Marine tailings disposal may in some cases be the best solution to one of mining’s major environmental problems. The public standing of this solution is poor, partly because of past bad practices. Among the tailings problems spreading of super-fines and toxic substances stand out. The two are often interrelated as heavy metals, insoluble to sea water, tend to adsorb on fines and spread piggyback on them. Only one paper seen, has addressed the mineralogy of fine particles in suspension. The topic was a secondary tailings deposit. Studies on the sedimentation of fines in large river estuaries show that different minerals sediment sequentially as the salinity of the river increase. Mineralogy in the particle size range where particle separation takes place, has so far, naturally been in focus for the mineral processors. Next to nothing is known about the fines which may cause environmental problems. Tailings disposal has, due to its complexity, to a large extent been taken over by specialists in other fields, biologists, engineering geologists, chemists. The basics of the subject ought also to be given more input by the mineral processing community. A drawn out battle about tailings discharge into some fjords has taken place in Norway. The detractors focus at fine particles (could be dangerous nanoparticles) spreading and emphasize the effects. Calculation is simple: 5 million tonnes tailings annually discharged, containing 1 wt. % < 1µm determined by laser diffraction, results in 50 000 tonnes of nanoparticles let loose in the environment. The industry`s difficulty to answer, is lack of basic research on this topic. Test work to develop a methodology to address the problem is described. One thing the mineral processors know is that final tailings may be comprised of tailings from separate separation processes, with different properties, some of which may require special treatment. One tailings stream from a Norwegian mine is investigated in such a context.

Jan 1, 2016

By K. Yamaguchi

To contribute highly efficient and environmentally conscious copper smelting process, several topics in chemistry of the continuous converting were discussed. Through the reviewing the authors&apos; thermodynamic simulations, it is recognized that small amount and low copper content of the coexisting slag is preferable. Some discussions were added to the Takeda&apos;s diagram for Cu20-FeOx-CaO ferrite slag, and the activity curves of the constituents were derived. Thermodynamic calculations were carried out on the copper contents of the slag during the blister copper formation. The dissolution of copper in slag decrease somewhat with increasing temperature, but the effects of increasing S02 pressure and decreasing %S in copper are considerable to increase in copper content of the slag. The optimum oxygen enrichment in the supplied air, and regulation of the oxidation degree for the blister copper are important in practice. The gypsum phase separation in the calcium ferrite slag was also evaluated thermodynamically, and concluded that decreasing temperature, increasing CaO content or S02 pressure, and extensive oxidation of the blister copper tend to separate CaS04.

Jan 1, 2007

By K. Reipas

"Westmin Resources Ltd. operates the 3300 TPD H-W underground copper/zinc mine on Vancouver Island. Ore storage underground is handled in a 6000 tonne coarse ore bin and a 3000 tonne fine ore bin. Both of these bins have experienced significant wear since excavation and construction in 1985. Wear problems have included both deteriorating rock walls as well as worn out steel liners and concrete at the discharge points from the bins. Extensive rehabilitation work was completed in 1993.The basis o/this paper is the rehabilitation work done on the coarse ore bin. The design and installation of ground control measures are discussed. The bin access methods used to allow the work to proceed quickly and safely are also presented. This involved the use of a Tekfoam safety bulkhead to protect workers.IntroductionMine DescriptionThe H-W mine was commissioned in 1985. Mine access is by vertical shaft with most production areas at a depth of about 500 m. Host rocks are composed of andesite and rhyolite. Mine capacity of 3300 tonnes per day is achieved mainly by longhole open stoping methods, complemented by room and pillar mining. Metals recovered from the massive sulphide ore are copper, zinc, gold, and silver. Mineable reserves at January I, 1994 were 9.7 million tonnes."

Jan 1, 1995

By E. Ghali, A. D. Bas

There is a lack of electrochemical studies of oxidized gold ores since the majority of previous studies were conducted with sulphidic gold ores. In this study, the influence of agitation and iron oxide minerals, i.e. magnetite, hematite, and maghemite on gold leaching was investigated by means of galvanic and passivation phenomena. Cyclic voltammetry studies of Roasted Gold Ore (RGO) in de-aerated electrolyte have shown one oxidation and one reduction reaction while three oxidation and one reduction peaks were observed with gold electrode. Galvanic coupling results by Zero Resistance Ammeter (ZRA) mode indicated that magnetite showed a negative effect on gold dissolution while maghemite and hematite showed a positive effect, relatively, as a result of higher galvanic corrosion rates. Generally, gold dissolution was found to increase in the initial 15 minutes. Increasing agitation speed from 100 to 400 rpm resulted in higher galvanic corrosion rates for RGO, magnetite, and maghemite electrodes, while 250 rpm was found to be optimum for hematite electrode. Passive products such as silver and iron-oxide were identified by XPS and SEM-EDS analysis, respectively.

Jan 1, 2015

By E. Nurminen

Thermal transport properties of copper flash smelting flue dust have been investigated. Such values of the dust are needed to correctly model the process and to optimize its heat recovery performance. Dust accretions on heat recovery boiler walls may have a significant influence on the boilers heat transfer efficiency. Measurements of the thermal transport properties have been made for industrial flue dust and for pure sulphate components. The measurements have been conducted at temperatures up to 400 °C and the effect of porosity on these properties has also been investigated. The results indicate that the flue dust and the sulphate components are effective thermal insulators and the dust build-up on the boiler walls is likely to greatly decrease the heat transfer efficiency of the boiler.

Jan 1, 2007

By Jirí Faltus

The paper deals with studying the impact of structural properties and anodizing of surface on the corrosion properties of extruded rods from commercial aluminium alloys: AA6082, AA6262, AA6012, AA2007 and new lead-free aluminium alloys AA6023, AA2015 and AA2111B. Samples were exposed to the corrosive atmosphere NSS, AASS in the chamber by EN ISO 9227. Surface of samples were either in the original state or anodizing by selected mode. The depth of corrosion attack and the form of corrosion attack are evaluated depending on the type of alloy, the metallurgical condition and surface treatment of the samples.

Jan 1, 2015

By J. J. Jonas, G. R. Stewart, A. M. Elwazri

Two important parameters for dynamic recrystallization can be derived from the changes in the strain hardening rate: the critical strain for initiation of dynamic recrystallization and the point of maximum softening. In this work, these values are determined from the flow stress-strain data obtained in continuous compression testing in the range 900-1100°C. The resulting strains are used to calculate a kinetic model of dynamic recrystallization for two materials: 304 austenitic stainless steel and a hypereutectoid plain carbon steel. The mechanical parameters used to define the proposed model are confirmed with quantitative metallographic analysis of the recrystallized microstructure.

Jan 1, 2004

By Larry M. Southwick

There have recently been executives at major metals companies who have recommended that Greenfield Projects not be pursued. Greenfield includes not only new geographical locations, but also new technologies and new types of feed materials. In the middle part of the 20th Century, two such projects were successfully commercialized to recover nickel from Cuban lateritic ores. One project (at Nicaro) used the Caron ammonia-ammonium carbonate leach and the other (at Moa Bay) a high pressure acid leach. How both of these projects dealt with these Greenfield issues will be reviewed, based on the original reports that described the research and development of the plants. This study will include a review of the critical ore characterization and sorting issues, as well as the extractive metallurgical, product recovery and equipment selection and sizing problems and how they were solved at each stage of project development, from laboratory through one or more pilot scale plants to start up and operation. In one case, a major revision of the plant was made after several years of operation to correct operating, equipment selection and materials of construction problems that hindered economical operation. These descriptions will provide a guide through the complicated and critical issues that in recent times have caused many companies to give up on similar development. Even with the more advanced analytical and computational tools available to today’s mineralogists, engineers and metallurgists, the basic concepts with which these projects successfully addressed their sets of problems are still required. In addition, upper management, now perhaps further removed from hands-on experience than was common then, will see how complicated problems require intense and detailed effort to avoid failure in the field and capital blowouts. Build it and we will make it run, kicking the can down the road and borrowing operating and design concepts incorrectly on technological issues, or nine year olds on a sugar high making financial decisions are not philosophies by which to succeed with Greenfield Projects.

Jan 1, 2014

By R. Niechcial

As populations grow and industry expands, the limited fresh water resources available are increasingly under stress. This situation creates conflict between communities and industry; and the sustainability of both is threatened. The symbiotic relationship between community and industry highlights the need to develop innovative solutions to these water shortages. The sea may hold the key to providing the resource to permit the development of industry, the sustainability of communities, and the protection of the dwindling legacy water resources around the world. Desalination technologies have developed to where it is now economically viable to create industrial and potable water quality from seawater. Nowhere is this development more important than in the arid region of Northern Chile, where high copper prices have encouraged a boom in mine development.

Jan 1, 2007

By E. Pallumbo, N. Szwedska, R. Asselin

"This paper highlights the results of collaboration between geology, mining and mineral processing teams during the restart of the North American Lithium Project, located near La Corne, Quebec, Canada. This collaboration was central in ensuring a cross discipline harmonization of design parameters and key inputs, all of which allowed for the development of an optimized life of mine plan suited to the particular needs of the operation.INTRODUCTION In July 2016, North American Lithium Inc. (NAL) began the process of restarting operations at the former Quebec Lithium Mine, located in the municipality of La Corne, Quebec, Canada. The North American Lithium Project (the Project) as it is known today, is the latest chapter in the history of this property. In order to provide a robust foundation for the project, multidisciplinary collaboration was instituted between the geology, mining and metallurgy teams. Despite the intrinsic link between these departments, in many instances their work is completed separate from one another; in silos. This collaboration highlighted specific drivers in the mining value chain that could be exploited to ensure that a saleable product could be produced effectively. This paper explores some of the concepts and strategies that were developed during the feasibility study that supported the project restart (excerpts from the study technical report have been used throughout this paper). PROJECT HISTORY In 1942, prospectors identified the presence of numerous spodumene-bearing pegmatite dykes on the Property. This led to additional interest and exploration drilling campaigns. In 1955, Quebec Lithium Corp. (QLC), who had acquired the property, began construction of an underground mine with mill facilities located on the surface. Operations began the following year at a production rate of 1,100 tonnes per day. A historical cross-section view of the underground mine is shown in Figure 1. In 1959, QLC began the construction of an on-site lithium refinery to produce lithium hydroxide. The refinery was finally operational by 1963. Mining and processing operations continued until 1966 when activities were halted due to a labour dispute. The property was sold and a few years later attempts to resume production were unsuccessful. Property ownership changed several times again until being acquired by Cambior in 1987. In the early 1990’s the existing mine and mill facilities were sold and the mine site rehabilitated"

Jan 1, 2019

By H. L. Gibson, T. N. Setterfield, J. J. Watkins, R. W. Hodder

"Abstract - The McDougall-Despina fault set in the Noranda district of northwestern Quebec defines the eastern margin of the Despina cauldron, nested within the district-scale Noranda cauldron. The faults are stratabound in that they displace stratigraphy of the cauldron fill, but do not off-set the cauldron cover. The faults are occupied by dikes that acted as eruptive centers to volcanic members of the cauldron-filling sequence. Measurable displacement across the McDougall-Despina fault set is greater than 750 m, and coincident with post-cauldron volcanism. Feeder dikes cross-cut each other and are typically depleted in Na2O and CaO, and enriched in MgO, K2O, Fe2O3 and MnO relative to fresh flows. Economic and subeconomic massive sulfide deposits occur adjacent to the McDougall-Despina fault set at different levels over a stratigraphic thickness of 3000 m. These include the Corbet deposit, the subeconomic D-68 Zone deposits, and the subeconomic stringer zones of South Rusty Hill and Bedford Hill. Numerous copper occurrences and abundant hydrothermal alteration occur in and immediately adjacent to the fault set.The McDougall, Despina, and adjacent, parallel, ancillary faults define a synvolcanic fault set which controlled the location of magmatism, hydrothermal alteration and mineral deposition during the early evolution of the Noranda cauldron. Significant sulfide mineral deposition commonly occurred in proximity to the intersection of the McDougall-Despina fault set with northeast-trending synvolcanic faults. Recognition of synvolcanic faults is therefore a major objective of exploration programs for volcanic-associated massive sulfide deposits."

Jan 1, 1995