Search Documents

By Subagyo, Geoffrey Brooks, Ken Coley

The generation of droplets and their subsequent reaction in the emulsion is critical to the overall kinetics of oxygen steelmaking. High temperature experiments have been performed at McMaster University to study this behavior. The results from this work and other previous studies has formed the basis of a number of physical and chemical models that attempt to describe the critical aspects of droplet behavior in Oxygen Steelmaking. These models include semi-empirical models for predicting droplet generation rate, droplet size distribution and droplet residence time as a function of blowing parameters.

Jan 1, 2004

By Karen M. Moffitt

Developments in mining methods and rates have led to an increase in the frequency and size of waste dump failures that have not been adequately predicted or explained in terms of conventional slope stability analysis. Monitoring data and visual observations suggest a unique mode of failure responsible for large runout events. A numerical model has been developed to capture commonly observed patterns of deformation, and investigate the formation of the ensuing failure mechanism. The analyses have yielded a good correlation with observed field behaviour and have provided significant insight into the coincident stresses and deformations within the dump. Results indicate that while creep effects in the waste dump could have a significant effect on the magnitudes of displacement, the overall dump stability is governed by the strength of the foundation soils underlying the toe region. Consideration of both the stress and velocity fields leads to factors of safety for various dump heights and foundation slopes that are considerably less than predicted from limit equilibrium analysis. The results suggest that conventional limit equilibrium analysis techniques may not be adequate when assessing the stability and design of waste dumps on steeply sloping terrain.

May 1, 2001

By L. Vinnett, T. Ledezma, F. Contreras, F. Díaz

"Mass balances in secondary grinding are subject to critical constraints mainly because of the unknown load distribution from the SAG mills, the uncertainties in the hydrocyclone split estimations and the lack of flowmeters in the key streams. In this paper, a methodology to support mass balances based on the use of radioactive tracer is presented. This approach was successfully implemented in two secondary grinding circuits of Minera Los Pelambres, which operate with ball mills of 21’ x 33.5’. The method allowed the load distribution of the SAG product (secondary grinding feed) to be determined. This load distribution was used as an input in the mass balance data reconciliation.The effective residence times of solid tracers were obtained in the secondary grinding equipment, where irradiated solid was used as a tracer. The residence times were obtained from the parametric deconvolution between the input and output tracer signals. The model fitting was performed to reconstruct the normalized output tracer concentration. Effective residence times of solid tracers in the ball mills ranged from 1.9 min to 9.5 min. The use of radioactive tracer measurement in grinding circuits is a powerful tool to consolidate mass balance results as well as to characterize grinding mills.INTRODUCTIONGrinding is the last stage of the comminution circuits. At this stage, the ore particles are reduced in size by a combination of impact and abrasion, either dry or wet (Austin & Concha, 1994). The grinding equipment mostly used in industrial operations correspond to horizontal tumbling mills (Wills & Napier- Munn, 2006). Tumbling mills employ steel balls or rods as grinding media. Ball mills, which are a type of tumbling mills, use steel grinding media with greater surface area per mass unit than SAG (semiautogenous grinding) mills or rod mills (primary grinding). Hence, the ball mills are suitable to obtain the particle size required in the next separation stages (Napier-Munn et al., 1996; Wills & Napier-Munn, 2006)."

Jan 1, 2016

"Since World War II, urban communities have expanded at an unprecedented rate. The industrial mineral industry supplies the sand, grave], limestone, crushed rock, cement, gyp-sum, etc. for urbanization. Most de-posits in use are close to or within communities. Pollution of water and air has become a matter of public concern. Waste disposal and the effects of noise and vibration are subjects of public debate. Need for the reclamation of land after operations such as strip mining is discussed in magazine articles and on TV pro-grams; i.e., the general public is educated in the unattractive features of mining.Legislation is on the books and being drafted to regulate mining operations and their side effects. To avoid over-regulation and restrictive legislation, it is necessary that the public be educated and legislators informed of problems peculiar to the mining industry. Our side of the story needs publicity."

Jan 1, 1968

By Z. Trojanová

Mg micropowders generated by gas atomisation of a magnesium melt with argon were mixed and ball milled with ceramic nanoparticles prepared by laser-induced gas phase reaction. The materials were then hot extruded. Specimens were deformed in tensile as well as compression tests at temperatures between 20 and 300 °C at a constant initial strain rate. The flow stress is significantly influenced by the test temperature. The yield stress decreases with temperature. This decrease and the flat character of the stressstrain curves at elevated temperatures indicate possible contributions of softening processes. The materials studied exhibit high-damping characteristics. The results are analysed and possible mechanisms are discussed.

Jan 1, 2006

By D. K. Sarkar, J. Perron, J. D. Brassard

"Nearly perfect spherical shaped water drops rolling-off from the surface of lotus leaf is one of the beauties of nature. This kind of surface is called superhydrophobic, since the water does not like it. Physically, a superhydrophobic surface provides a contact angle (CA) of water over 150°. The combinations of both mico-nanostructure topography as well as low surface energy are essential to have such high CA on a surface. Nano-micro structured superhydrophobic surfaces have been developed in different methods. (i) Monodispersed fluorinated silica nanoparticles have been synthetized via Stöber Sol-Gel process and deposited on various surfaces, such as aluminium or glass, to obtain transparent superhydrophobic thin films. (ii) Similarly, zinc stearate nanocomposite coating has been fabricated by spray process on the same substrates. These thin films are found mechanically robust with drag reduction of coefficient 16% lower than as-received surfaces. (iii) By electrodepositing pure zinc on steel surfaces and further coating it with diluted room-temperature vulcanized silicone rubber, the surface become superhydrophobic. This superhydrophobic surface protects the steel against corrosion by increasing the polarization resistance from 1.5 k? on steel to 44.4 k?. This coating also reduced the ice adhesion on the steel surface 6.3 times as compared to bare steel substrates. Globally, these superhydrophobic surfaces have tremendous applications against corrosion reductions, drag reductions and ice adhesion reductions.INTRODUCTIONSuperhydrophobic coatings are increasingly attractive to the industry and academia due to their unique self-cleaning properties as a result of their water repelling characteristics. Fabrication of superhydrophobic coating is an inspiration from nature as water is seen to repel on many natural surfaces such as those of the lotus leaves, butterfly wings, water striders’ legs, and so on (Gao & Jiang, 2004; J. Huang, Wang & Wang, 2006; Neinhuis & Barthlott, 1997; Zheng, Gao & Jiang, 2007). This non-wetting phenomenon is well understood on lotus leaves, shown on the Figure 1 (a), and it is considered as the basis of the studies of superhydrophobicity. The existence of this binary structure on the surface of the lotus leaves allows a large amount of air entrapment and consequently reduces the contact area of water on it and the presence of low surface energy waxy components with reduced affinity to water together leads to the superhydrophobic properties. The phenomenon is shown on Figure 1 (b). Cassie and Baxter (Cassie & Baxter, 1944) as well as Wenzel (Wenzel, 1936) proposed two mathematical models to explain the wetting phenomena on rough surfaces that leads to superhydrophobic properties. By definition, superhydrophobic surfaces are characterized by a water contact angle value = 150° with the rolling off of water drops from the surfaces (Sarkar & Saleema, 2010). Superhydrophobic surfaces find tremendous importance in the technological world where it can applied in domains such as anti-corrosion, anti-biofouling, electrowetting, icephobic and even in drag reductions (Bushnell & Moore, 1991; Cao, Jones, Sikka, Wu & Gao, 2009; Carlborg & van der Wijngaart, 2010; Carré & Mittal, 2009; Y. Huang, Sarkar & Chen, 2010a; R. Karmouch, Coude, Abel & Ross, 2009). However, the most important challenge faced by industries is their feasibility large scale in an effective an economical manner."

Jan 1, 2016

By R. ZapataN.

"In the following report, Altonorte Smelter owned by Xstrata will explain its experience with its denominated furnace called ""Continuous Altonorte Reactor"" since started up in March 2002. The Reactor is the main and only smelting furnace since the operation of Reverb Furnace was stopped (15 days after the start up of the Reactor) and it can be operate with dry concentrate for injection by tuyere and wet concentrated via Garr Gun when the injection system fails. From the started up of the Reactor, three operational campaigns have been carried out where in each one they have been increased their smelting throughput and availability. The flexibility reached by the technology bath smelting has allowed a high level of smelting of concentrate and revert materials. The high availability of the Reactor and overcoming problems that were considered of high complexity like the extraction of white metal and slag, refractory campaign, etc. has allowed the Altonorte smelter to project to smelting 1,200,000 tonnes per year with its only Reactor in next year."

Jan 1, 2007

By George J. Thompson

This pa per deals with the internal characteristics of steel and its response under cold northern temperatures. General maintenance procedures and specific repair techniques are covered.

Jan 1, 1973

By D. B. Apel

As depths to the ore bodies keep increasing around the globe, the problem how to deal with the increasing temperature of undisturbed rock mass becomes very important. In extreme cases the rock temperature at the bottom of the mine could raise up to 80 °C. In deep mines, geothermal heat is considered as the primary heat load contributor, which accounts for 50?90% of the total heat load depending on different geological conditions. Thus the geothermal heat control in underground mines is the most important and demanding issue to ensure a suitable working environment. In this study, expanded perlite aggregate (EPA) was incorporated as a lightweight substitute for sand. Five mixtures were prepared using 0, 25, 50, 75 and 100% replacement ratios of sand by EPA. These, mixtures were tested in the laboratory for both the insulating and strength properties of the developed shotcrete. The goal of this research was not only to develop shotcrete which would exhibit good insulating properties but also which would exhibit strength properties similar to the regular shotcrete. This paper not only reports the results of the laboratory tests but also discusses the output of numerical model which was performed to evaluate the benefits of using the insulating shotcrete in reducing the cooling costs at hot underground mines.

Aug 1, 2013

By J. Y. Kim, Kenneth Stowe, Stephen Chryssoulis

"A series of flotation tests was carried out on Brunswick Mining ore with various pH modifiers (soda ash, lime, KOH) and added ions (ferric, nitrate, sulphate) in the copper lead rougher circuit. The main objective was to identify downstream effects on sphalerite activation and subsequent zinc rougher flotation. Some significant differences in zinc flotation were obtained. Most notably, soda ash and nitrate ions had a positive impact and ferric ions a pronounced negative effect on selectivity.Selected products from the flotation tests were deslimed at 400 mesh, washed with methanol, air dried, placed in teflon vials purged with nitrogen and stored at -15 degrees C. Numerous liberated sphalerite and pyrite particles were selected under a stereoscope and placed in rows on indium foil. The surface compositions of the particles were analyzed with an innovative laser probe (LIMS). The very small analysis area of the LIMS enables the surfaces of individual grains to be characterized. In addition, the rapid analysis time allows a statistically significant number of grains to be analyzed quickly.Surface lead appears to play a major role in zinc activation/flotation. Possible mechanisms are proposed to explain the variations in metallurgical performance at the different test conditions.IntroductionAlthough the bulk composition of mineral grains is an important consideration for the mineral processor it is ultimately surface composition and topography (edges and dislocations preferred sites for reactions) that control reactivity in flotation and cyanidation (passivation, encapsulation and preg-robbing). Determination of the surface properties of particles from process streams poses a particular challenge for the surface chemist for a variety of reasons, including:"

Jan 1, 1994

By H. O. Olsen

"GeneralTHE IRON ORE at Marmora is a replacement deposit of Precambrian limestone and is overlain with Palaeozoic limestone. It is a low-grade magnetite deposit and the ore will require concentration be-fore it can be used economically for the production of iron and steel.Present plans estimate an annual production of 500,000 tons of concentrate in the form of pellets. This will require mining approximately two million tons of ore and\ waste annually. Shipment of pellets from Marmora to a ship-loading dock at Picton will be made by rail on a year-'round basis. Shipments from Picton to the Lackawanna plant of the Bethlehem Steel Company at Buffalo, N.Y., will be carried on during the Lake shipping season.LocationThe mine, located a mile southeast of Marmora village in Hastings county, Ontario, is 31 miles north of Belleville and 3•7 miles east of Peterborough. Marmora is 130 miles from Toronto and 150 miles from Ottawa. Highway No. 7 passes half a mile north of the mine and Highway No. 14 half a mile west of the mine. The Canadian National railways' branch line between Trenton and Bancroft passes through the property just east of the open pit.HistoryThe Ontario Department of Mines conducted an airborne magnetic survey of the district during 1948 and 1949. Maps of this survey were released to the public early in 1950. Bethlehem representatives carried out ground surveys in the Marmora area shortly thereafter and in June, 1950, commenced diamond drilling."

Jan 1, 1955

By E. Cauda, K. Phillips

"Diesel particulate matter (DPM) exposures are a serious occupational health hazard in underground mines. While the complex nature of DPM makes direct analysis difficult, its primary component, elemental carbon (EC), can be used as surrogate. The near real-time FLIR Airtec monitor measures EC mass based on laser extinction. It was developed for use in underground metal/non-metal mines, and calibrated to the NIOSH Method 5040. Its effectiveness has not been demonstrated in coal mines, however, where coal-sourced EC could produce analytical interference. To gain preliminary insights regarding the Airtec’s performance in the presence of coal dust, experiments were conducted in a controlled laboratory chamber. The Airtec EC results consistently underestimated Method 5040 EC for both respirable-sized and submicron coal dusts. While underestimation of coal-sourced EC bodes well for limiting coal interference for DPM measurement, one key reason for the observed trend was non-uniform coal particle deposition on the Airtec filter. This may be problematic in coal mines where DPM and coal dust occur together in the instance that DPM deposition is also non-uniform. INTRODUCTION Diesel particulate matter (DPM) is an occupational health hazard, and underground miners have the potential for relatively high exposures due to their work in confined environments with large diesel equipment (NIOSH, 2011). DPM is heterogenous and complex in terms of its chemical composition (Birch & Cary, 1996; Noll et al., 2006), but elemental (EC) and total carbon (TC) are often used as analytical surrogates (Birch & Noll, 2004; Noll et al, 2015). EC is the solid “soot” component of DPM, whereas TC also includes particulate organic carbon (OC) (Noll et al., 2007). EC and OC can be measured in filter samples using the standard NIOSH Method 5040 (NIOSH, 2003), and summed to obtain TC. In US mines, TC has been adopted as the analytical surrogate for DPM in regulatory activities. In metal/non-metal mines, personal exposures are limited under 30 CFR Part 57. In coal mines, limitations are made on emissions from each piece of equipment (30 CFR Part 72) rather than for personal exposures. This is because coal dust has the potential to interfere with TC measurements in personal samples. In some other countries, and for non-regulatory purposes in the US, EC is also commonly used as a surrogate for DPM in mine monitoring applications [e.g., see AIOSH, 2013). EC generally exhibits a linear correlation with TC (Birch & Cary, 1996; Noll et al., 2006 and 2007) but unlike TC measurements, which are analytically intensive, EC can be determined more simply using a laser absorption/extinction principle on filter samples (Noll et al., 2013)."

Jan 1, 2019

By Herbert D. Drechsler

"THE FOLLOWING are some comments on the article, ""International Trade in Minerals and Economic Development"", by M. Sengupta, published in the October 1976 issue of the CIM Bulletin.Sengupta says in the introduction that ""The mechanism through which this growth (economic development) has occurred is basic ally straight forward"". His statement is quite misleading and perhaps it is better to quote Gerald Meier:""Development economists must operate in an imperfect second-best world, away from the simplified premises of neoclassical economics. Their subject matter is therefore not yet a coherent or self-contained discipline. Denied recourse to a set of general principles, perhaps the student's most sensible introduction to economic development is through a study of 'leading issues' that are at the time a major preoccupation of the development economist and development practitioner"" .Sengupta quotes an authority who wrote 18 years ago. Academic and operating development economists today know full well that existing theory is quite deficient. Sociologists, political scientists and engineers in this field also know that economic, social, political and technical development involves all academic disciplines.Sengupta indicates that tariffs in developed countries prevent less developed countries from supplying refined metal, or manufactured and semi-manufactured products. He lists Zambia, Chile and Zaire as examples of copper concentrate exporters, as inadequately shown in Table 1. He is wrong."

Jan 1, 1977

By M. Maldonado

This work details the application of a decentralized control strategy to a pilot flotation column working with a two-phase system (water-air). The process is represented by a multivariable system composed of three inputs and three outputs. The selected control variables are the froth depth, the air hold-up and the bias rate, whereas the corresponding manipulated variables are the set-points of the local flow controllers of tailings, air and wash water. All controlled variables are estimated using electrical conductivity based techniques. In particular, the results of a new method for estimating the bias rate, based on the measurement of the volumetric fraction of wash water under the interface, is presented. This method reduces the coupling problem associated to the bias estimation as a difference between feed and tailing water rates. Moreover, the nominal system transfer matrix can be represented by an upper triangular matrix, in such a way that the closed-loop system stability reduces to the stability of the independent control loops. The experimental results show that the closed-loop system performance, particularly that of the bias rate loop, is strongly dependent on the air flow rate, reaching in some cases the saturation point of the controller.

Jan 1, 2007

By S Sokhanvaran

Electrodeposition of silicon from a cryolite based electrolyte at a relatively low temperature (1000°C) is a promising approach to generate high purity silicon. In order to obtain fundamental data pertaining to electrowinning of silicon from Cryolite?SiO2 melts, density and electrical conductivity measurements were made. A range of temperatures and SiO2 contents was studied for each property. It was found that while density has an inverse relationship with temperature, the dependence for electrical conductivity is direct. Increasing silica content up to the saturation limit (~ 5 wt%) increases the density whereas further increase in SiO2, lowers the melt density. On the other hand, the conductivity is lower for the melts with greater SiO2 content, at any temperature.

Jan 1, 2011

By Bertrand Quiniou, Pierre Amadieu

Ion exchange technologies and processes are proven and established technologies widely used in numerous industries including hydrometallurgy for metal separation and recovery from metal bearing solutions. They have evolved through innovation which includes the development of countercurrent multistage (or multivessel) ion-exchange contactor systems with the benefit, for industrial operations, of greatly reduced footprints and ion-exchange media inventories, as compared to more traditional fixed bed contactor systems. Information on procedures for design and sizing of countercurrent multistage ion-exchange contactor systems is not readily available since it is most often proprietary know-how. The purpose of the present work is to develop a simple and innovative approach for the sizing and modeling of industrial countercurrent multistage ion-exchange contactor systems. The suggested approach builds upon published results and upon the following observation: in an industrial setting, knowledge of how component concentration or load on a contactor output streams vary with time t within a cycle duration (0 < t < T) is generally of little interest, only knowledge of time average of such concentration or load over a cycle duration T is sought for. The presented approach will be tested against current or past performances of industrial countercurrent multistage contactors of Orano Mining operations such as SNK‑3M moving packed bed contactors in Kazakhstan and NIMCIX fluidized bed contactors in Namibia.

Jan 1, 2020

By Yann Sivry, S. Subramanian, Divyasree C. Prabhakaran, Jean Riotte

The potential of a bacterial strain isolated from water samples collected from a chromite mine in Odisha, India has been assessed for the bioremediation of hexavalent chromium, a toxic environmental pollutant. The isolate was identified as Sphingopyxis sp., a Gram negative bacterium, adopting molecular biological protocols and biochemical characterization techniques. Detailed investigations on the bioremoval of Cr(VI) were carried out using Sphingopyxis sp. cells and the various parameters affecting the biosorption process were evaluated. About 55 % biosorption of Cr(VI) was obtained using Sphingopyxis sp. bacterial cells and the residual chromium in solution was found to be bio-reduced to the trivalent form, namely Cr(III). Thus, complete bioremediation of Cr(VI) could be achieved using the mine isolate, with contributions from both biosorption and bioreduction mechanisms. The Cr(VI) biosorption isotherm obtained for the isolate was found to follow a typical Langmuirian behavior and the free energy value of biosorption was determined to be ~-25 kJ/mol, indicative of involvement of chemical binding forces in the bioremediation process. The chromium biosorption kinetics by the isolate followed a pseudo second order reaction. The FTIR spectral studies revealed that carboxyl, hydroxyl, amino and phosphate groups were involved in the biosorption process. X-ray photoelectron spectroscopic studies on the bacterial cells interacted with Cr(VI) confirmed the presence of both Cr(VI) and Cr(III) on the cell surface. The electrokinetic studies revealed that the surface potential of the bacterial cells were less electronegative subsequent to interaction with Cr(VI), compared to the cells alone, which further testified to the binding of positively charged Cr(III) ions, formed by bioreduction of Cr(VI), to the bacterial cell surface. A marginal shift in the iso-electric point obtained for the bacterial cells interacted with Cr(VI), corroborated the involvement of chemical binding forces in the bioremediation process.

Jan 1, 2016

By T. J. Langan, M. Ramajayam, T. Dorin

"6xxx-series Al alloys are the most commonly used alloys in the automotive industry as they have an appropriate balance of strength, corrosion resistance and formability. The main strengthening phase in these alloys is the ß’-Mg2Si precipitates. One opportunity to achieve stronger 6xxx-series Al alloys, without affecting corrosion and formability, is the use of Sc. The main challenge of using Sc in 6xxx-series lies in the heat treatment, which must be designed to allow for a fine precipitation of both Al3Sc and ß’-Mg2Si. In this work, two model alloys are used, an Al-Sc-Zr and an Al-Mg-Si-Cu-Sc-Zr, to explore the impact of the 6xxx-series key elements (Mg, Si and Cu) on the Al3Sc precipitates. Transmission electron microscopy and atom probe tomography are used to investigate the precipitates present in the microstructure after casting. We find that higher Si content results in the formation of dispersoids upon casting. The average composition of these dispersoids is (Al0.8,Si0.2)3 (Sc0.888,Zr0.024,Mg0.08,Cu0.008). A closer look at the solid solution reveals that most of the Sc and Zr is supersaturated after casting even in the presence of Mg, Si and Cu. We discuss the impact of these results on the design of a suitable heat treatment for 6xxx-series alloys with Sc.INTRODUCTION The most common strategy to strengthen aluminum (Al) alloys is by micro-alloying to form a fine distribution of precipitates (Gladman, 1999). Whilst precipitates enhance the strength, this is often done to the detriment of ductility and corrosion performance (Davis, 1999). The 6xxx-series Al alloys are heavily used in the automotive industry as they offer an appropriate balance of strength, ductility and corrosion resistance (W. S. Miller et al., 2000). The strength increment in these alloys comes from the formation of the ß’–Mg2Si and the quaternary Q’ phase (Chakrabarti & Laughlin, 2004; Polmear, St. John, Nie, & Qian, 2017). One opportunity to achieve stronger 6xxx-series alloys, whilst keeping good balance of corrosion resistance and formability, is the use of small additions of scandium (Sc). Sc is one of the most potent strengtheners in Al alloys (Dorin, Ramajayam, Vahid, & Langan, 2018; Røyset & Ryum, 2005). Most of the strengthening benefits from Sc come from the formation of fine Al3Sc dispersoids. The following strengthening mechanisms apply to Sc: 1) Solid solution strengthening, 2) precipitation hardening, 3) inhibiting recrystallization, 4) assisting nucleation of other strengthening phases (Dorin, Ramajayam, Lamb, & Langan, 2017). As compared to other dispersoid phases, Al3Sc dispersoids have good electrochemical compatibility with Al alloys and hence do not affect their corrosion resistance (Cavanaugh, Birbilis, Buchheit, & Bovard, 2007). The coarsening resistance of Al3Sc is often improved by adding zirconium (Zr), as it forms a Zr rich shell around Al3Sc which prevents Sc from moving across the interface."

Jan 1, 2018

By Nabeel Khan

Annual oil production from the Canadian Oil Sands in Northern Alberta has been rising for several decades, and more ore and overburden are excavated each year from an increasing number of open pit mines. Overburden meeting certain specifications will be used to dam tailings and fill open pits, but the remaining material must be stored in overburden storage structures (OBSS). Well-designed overburden storage structures are more stable and cost less in the short- and long-term. The purpose of this paper is to explore OBSS designs that will be stable yet economical in the short- and long-term. The geological background of the site is briefly discussed, including the effect of each of the main geologic layers (recently deposited till and muskeg, Clearwater Formation clay shales, McMurray Formation oil sands, and the Devonian limestone) on the slope stability of the OBSS. Cost is considered in the analysis when balancing between minimizing costs (steeper slopes) and acceptable factors of safety (flatter slopes), all the while considering the financial consequences of failure. Potential failure planes are identified and probabilistic analysis is conducted on the critical failure surface. The variations in the factor of safety caused by varying pore water pressure, friction angle, and cohesion, are plotted and discussed.

Jun 1, 2012

By Michael S. Moats, Prashant Bagri

"In recent years with increasing concerns about energy consumption in hydrometallurgical processing, there is an ongoing attempt to use Catalytic Titanium Anodes (CTAs) for copper electrowinning. For this work, anodes with IrO2 - Ta2O5 coatings were prepared in the laboratory with the same total coating loading but varying the number of layers by changing the speed of withdrawal in dip coating. A second set of CTAs were fabricated on niobium, Ti Grade 1, Ti Grade 7 and Ti Grade 36 metal substrates. All the anodes prepared in the laboratory were characterized using standard electrochemical techniques and subjected to accelerated life testing. It was found that the coating would not adhere to the niobium substrate, the grade of titanium had a minimal to no effect on the life of the anode, and it is observed that as the coating speed slows, there is an increase in the electrochemically active surface area of the coating which seems to directly contribute to an increase in the Tafel slope of the anodes. There was inconclusive evidence on the effect of coating speed on anode lifetime.INTRODUCTIONLarge scale hydrometallurgical extraction of copper has become widely practiced over the last 40+ years. The hydrometallurgical route entails leaching, solvent extraction and electrowinning. With the increasing desire to process refractory sulphides like enargite and chalcopyrite through the hydrometallurgical route, use of hydro-processing of copper is expected to remain high.In conventional electrowinning, copper is deposited on the cathode and an inert anode is used for oxygen evolution. Presently, the most common anode material is rolled lead-calcium-tin and the cathode is 316L stainless steel (Robinson et al., 2013). This lead alloy is fairly inexpensive and is robust, providing lifetimes typically of 4+ years. The main drawbacks of lead alloys are their relatively high oxygen evolution overpotential, the need for cobalt in the electrolyte to reduce their corrosion, the contamination of cathode product by lead, and the generation of harzardous by-products (Hiskey, 1999)."

Jan 1, 2016