Search Documents

By Dwayne D. Tannant

The Fox Pit at EKATI Diamond Mine reached a depth of approximately 150 m as of September 2005. The pit is designed with 11 m wide benches excavated using a double benching technique leaving 30 m high bench faces. A series of blasting tests were conducted to improve catch bench reliability and increase the percentage of benches that meet an 11 m catch width. The design changes focussed on reducing damage to the bench crest because maintaining the bench crests is the most important factor in achieving good bench reliability. The most significant improvement was obtained by raising the bottoms of the lower trim blastholes by 0.5 m. This change decreases the depth of broken rock below the final bench elevation, and consequently reduces damage to rock that forms the bench crest below. Another improvement was the use of smaller diameter (165 mm vs. 270 mm) blastholes in the A and B rows for the upper trim blast. This change reduces the charge per delay during detonation, reduces the powder factor slightly, and reduces the energy affecting the final pit wall and crest. As mining and the blast testing progressed, the portion of the bench with crest achievements (>11 m) increased from 57% to 75%.

May 1, 2006

By N. Saracoglu, J. P. Golightly, R. H. Wallis, J. J. Brummer

"In January 1974, the Minerals Division of Canadian Occidental Petroleum Ltd. made the strategic decision to add uranium to its active exploration commodities and through compilation studies selected northern Saskatchewan as the most attractive and cost-effective exploration area in Canada. In August 1974, 100 sq. miles were staked adjacent to Gulf Minerals' Rabbit Lake deposit and east of the Esso Minerals Midwest boulder train. Initial exploration was based on geologic models of the Rabbit Lake deposit.In the summer of 1975, surface surveys delineated radon anomalies which were drilled that winter and found to overlie anomalous concentrations of uranium in the regolith which forms the upper unit of the crystalline basement. Within the crystalline basement, one hole intersected graphite and pyrite with anomalous nickel-cobalt-arsenic. Geochemical and radiometric surveys followed in the summer of 1976. Drilling in the winter of 1977 intersected several zones of graphite and also anomalous, but uneconomic, uranium abundances. Also in 1977, Dahlkamp and Tan (1977) described the coincidence of graphite and uranium at Key Lake and ground EM surveys on CanadianOxy claims detected graphite conductors beneath 250 ft of Athabasca sandstone. Inco Limited joined the project in April 1977 as a 50% partner. The project area was then surveyed using the airborne INPUT EM method, which detected 84 miles of conductors, with associated graphitic metasediments. On the ground these were located with MaxMin surveys, and follow-up drilling located the ""Tent"" Lake uranium zone.In 1978, the Midwest and Dawn Lake discoveries were announced, 7 miles and 2 miles west of the Joint Venture (J.V.) claims; and, in part for this reason, the 1979 winter drilling was concentrated on the deeper west side of the property. Exploration hole 102-79 intersected altered and uraniferous rocks, but stepout holes were barren. Drill hole 153-79 tested an under-snow three-station radon anomaly east of hole 102-79 and intersected 33 feet of 7.51 % U3O8, confirming the disco very of the McClean North zone. The geophysical grid of the McClean North conductor system was extended and detailed a strong, continous conductor to the south, called McClean South. This was drilled in January 1980and hole 1004-80intersected 22 feet of 2.95% U3O8."

Jan 1, 1983

By L. B. Tsymbulov, N. A. Fedorova

The equilibrium of exchange reaction (Cu20)+[Ni]=(Ni0)+2[Cu] taking place in the course of interaction of metallic nickel-containing copper melts with different oxide melts (Cu20-NiO, Cu20-NiO-Si02, Cu20-NiO-FeO(Fe203)) in the area of their homogeneity has been studied. The studies, based on the known value of equilibrium constants and defined copper and nickel activity indices in metallic melts and equilibrium concentrations of Cu, Ni, Cu20 and NiO, determined the YNio/ycu2o ratios in the oxide melts of the above systems. For the equilibrium between nickel-containing copper and binary oxide melt Cu20-NiO, values of YNiO and Ycu2o were determined both by calculation and experimentally. Based of the data conclusions regarding oxide melts construction are presented.

Jan 1, 2007

By J. E. Dutrizac

Mercury balances have been obtained for the flotation circuits at Pamour Porcupine Mines, Timmins, Ontario, and at Brunswick Mining and Smelting Corporation, Bathurst, New Brunswick. The mineral form of mercury in both deposits has been ascertained. At Pamour Porcupine, the mercury is approximately evenly divided among sphalerite, native silverelectrum and tetrahedrite-tennantite; at Brunswick Mining, this element is contained mostly in the sphalerite, although tetrahedrite (and possibly pyrite) also contains minor quantities.

Jan 1, 1979

By L. Bichler

Utilizing thermal analysis techniques, pioneering research into the solidification mechanism of a popular magnesium alloy AZ91E cast by the Lost Foam Casting (LFC) process was carried out, Foam characteristics, section thickness and application of vacuum were seen to have profound effect on the cooling rate, thermal gradients and casting temperature profiles.

Jan 1, 2005

By Brian Hall

For some years, the mining industry has been consistently delivering returns below the market average. One of the causes is a disconnect between what is perceived to drive value creation by many industry analysts and senior corporate executives, and what actually drives the intrinsic value of mining operations. The perverse effect is that strategies that should increase value are perceived to have the potential to drive share prices down, and vice versa. This paper challenges common perceptions of what drives a mining company?s value. Anecdotal evidence suggests that the key drivers of value in the market, and hence in many boardrooms, are such things as increasing the reserves and production rate, and reducing unit operating cost. However, while the quoted reserves may satisfy ore reserves reporting code requirements to be economic, this does not imply that they are optimal. Often, a proportion of the quoted reserve reduces the potential value of the operation. Metal price increases, increased production rates, and operating cost reductions are all seen as conditions or actions that can improve value, and lead to cutoff grade reductions, thereby increasing ore reserves. However, modern cutoff theory and studies conducted by the author and his colleagues show clearly that, while breakeven cutoff grades will fall in these circumstances, optimum cutoffs may be much less volatile, and may even increase. Results from case studies indicate that value is maximised by right-sizing, not maximising, the production capacities, and by optimising the cutoff strategy. Values of many existing underground mining operations can be increased significantly by a substantial cutoff grade increase. Also, an increase in downside risk, and hence reduced returns, can occur using typical life-of-mine planning strategies if prices received are lower than predicted. Since this is often the case, low industry returns may be a direct result of typical strategic mine planning processes. Relatively simple cost-effective techniques are available to provide senior decision makers with information needed to assess the tradeoffs between their many conflicting corporate goals, and the balance between risk and reward. Often this information is not being generated at all. If it is, decisions affecting the value of the company are occurring by default at relatively low levels within the hierarchy, with senior executives apparently unaware of them or their potential impact. The paper concludes that without a re-evaluation of the way mining projects are valued, to demand proven value optimisation from mining plans by boards and mining analysts, the industry will continue to deliver below average returns.

May 1, 2003

By Christopher McElman

Real-time mine management solutions have evolved over time from closed, proprietary solutions, to a "system of systems" that may include a wide variety of off-the-shelf components and technologies. Modular Mining Systems has embraced open standards for their NextGen products to bridge the technology gaps between these systems. However, the remaining logical gaps must be overcome, in order to achieve truly seamless integration between discrete systems. When dealing with volatile real-time management problems, the effectiveness of business process modeling and middle-ware can break down. Scientific principles of military command and control applied to mining domain help to achieve better alignment and reach the highest level of integration. The combination of open standards and off-the-shelf hardware and software with a deliberately structured command-and-control approach provides a clear evolutionary path from ad-hoc connected systems towards real-time management of a seamlessly integrated digital mine.

Oct 1, 2009

By L. C. S. Dharmasiri, S. M. Shin, A. Senaputra, J. S. Sohn, K. H. Park, J. Avraamides

Reducing agents can be applied to leach metal values from natural and secondary resources such as laterite ores and deep sea manganese nodules and recycled materials such as spent batteries / catalysts which contain high-valent metal oxides of manganese, cobalt and iron. Selective leaching of some metals can be achieved by selecting conditions to control the saturated solubility and dissolution rates of metals from oxides or mixed metal/oxide matrices. The leaching results are rationalized on the basis of chemical species, Eh-pH diagrams and heterogeneous kinetic models. The role of reducing agents such as hydrogen peroxide, sulfur dioxide and iron(II) sulphate, in acid, alkali and in the presence of complexing ligands such as ammonia for the improvement of the leaching of metal oxides and metals is discussed. Previous studies on acid leaching of metals from nickel laterites, manganese nodules and spent catalysts/batteries in the absence or presence of reducing agents show that the rate controlling step involves the diffusion of protons through a thickening product layer on the particle being leached. It is shown that the leaching of nickel and cobalt from manganese nodules and zinc-carbon batteries in ammoniacal sulphur dioxide solutions also obey shrinking core kinetics.

Jan 1, 2014

By J. Shahabpour

"Breccias with angular and rounded clasts of a late-mineralization, ""barren"" hornblende porphyry dike set within a comminuted matrix consisting of rock fragments and quartz, cemented by quartz and K-feldspar of hydrothermal origin is observed in diamond drill cores from the Sar Cheshmeh porphyry copper deposit. Studies of age relationship between vein types, phyllic-altered clasts and the breccia groundmass suggest that the brecciation is a late event. The breccia clasts record evidence of hydrothermal reaction between the clasts and fluids responsible for the brecciation.Formation of bornite, in the breccia clasts of the originally barren hornblende porphyry dike, and in the breccia matrix, along with the scarcity of bornite in the Sar Cheshmeh deposit itself suggest involvement of fluids which are later and of different composition from the fluids responsible for the known mineralization at Sar Cheshmeh. These later fluids may be related to a later plutonic event and suggest the possibility of a later, and concealed deposit."

Jan 1, 1994

By N. Depountis, Th. Rondoyanni, N. Sabtakakis, K. Kavoura, G. Tsiambaos

"Some typical landslide phenomena in Western Greece, in terms of the geological composition and structure of the affected materials, induced by heavy rainfalls are thoroughly studied and analyzed. The studied cases involved composite landslides on Flysch and Neogene weak rock materials that constitute the most critical landslide prone geological formations in Greece. The studied cases named Platanos, Platanitis and Karya include representative landslide sites as regards to the geological composition and structure of the displaced formations. Thus: (a) flysch formation includes different lithological units as shales, marls, siltstones, sandstones and conglomerates and is closely related to the Alpine orogenesis, suffering intense past tectonic movements and (b) the Plio-Pleistocene sediments include clayey marls, marlstones and siltstones. The investigated landslides , affecting mainly transportation routes, are closely related to heavy rainfalls induced by extreme meteorological events and are controlled by active fault tectonics. Long term movement monitoring using borehole inclinometers and surface benchmarks showed that landslides control was effective only when the proper stabilization measures were taken.INTRODUCTIONLandslides represent a major threat to human life, property, infrastructure and natural environment in most regions of the world. They are recognized by the scientific and politic authorities as having a major socio-economic impact and they represent a significant hazard for the population and the properties in particular locations. Landslide hazard expressed as the probability of occurrence within a reference time period and is a function of the spatial and temporal probability (Varnes, 1984; Guzzetti et al. 1999; Lee and Jones, 2004). The spatial probability of landslide initiation (susceptibility) is mainly related to static causal factors (slope inclination, material properties, etc.), while temporal probability is mainly related to dynamic causal factors such as rain input, increased groundwater levels and drainage, earthquakes, etc. (Van Westen et al. 2005)."

Jan 1, 2015

By Ali M. Ghazi, Ronald J. Goble, Lowell S. Whiteside

"Geerite (Cu1.6S) is a rhombohedral copper sulphide which occurs naturally in epitactic replacement of sphalerite; cell dimensions closely approximate those of the host sphalerite.Geerite-type structures can be produced by leaching digenite (Cu1.8S) in ferric sulphate solutions. X -ray diffract ion and electron microprobe studies indicate that eight metastable geeritetype structures can be produced, depending upon the concentration of f erric sulphate solution used and the duration of the each. Although compositions cluster on or near values observed for natural phases, optical properties indicate that we are dealing with polymorphs of these phases. Leaching of chalcocite (CU2Sj in dilute f erric sulphate solutions produces similar results. In contrast, leaching of chalcocite in more concentrated solutions seems to produce true analogues of natural minerals.During froth flotation, sphalerite is activated with a monolayer of floatable copper sulphide with the composition, CuS, of the mineral covellite. However, covellite is not significantly more floatable than sphalerite, and has an incompatible structure because of the presence of covalently-bonded atoms of sulphur. Leaching ofdigenite was used to produce a polymorph of covellite with a geerite-type structure, compatible with that of sphalerite. This polymorph has a flotational behaviour similar to copper-activated sphalerite, suggesting that the monolayer has a geerite-type CuS structure. IntroductionIn an ideal close-packed sulphide structure the distance between sulphur layers, D, is equal to 2R 2/3, where R is the radius of the sulphur atoms. In sulphides with covalently-bonded sulphur layers, such as covellite (Fig. I), D will be an average of the number of covalentl y-bonded and close-packed sulphur layers, weighted as to the relative number of each type of layer. Both D and R are spacings which are readily identifiable structurally and on X-ray diffraction patterns. Goblel has shown that for copper-iron sulphides with metal-to-sulphur ratios between 0 and 2 and copper-to-total metal ratio s between 113 and I there are strong correlations between composition and measured D and R distances (Fig. 2). D can be represented by a single empirical equation relating interlayer spacing to composition; R must be represented by three equations relating the radius of sulphur atoms to composition. One of these equations (R, in Fig. 2) represents ideal close-packed behaviour, the other two represent sulphur radii greater than (R1) or less than (Rh) the ideal."

Jan 1, 1988

By H. Sakurai, M. Kato, F. Tanaka

The Mitsubishi Continuous Copper Smelting/Converting Process employs an electric furnace (CL- furnace) for settling the slag/matte mixture formed in the smelting furnace. The conditions in the CL- furnace change its settling efficiency, resulting in high variability of copper losses in slag. Modifications of the operation and maintenance procedures for the CL-furnace have significantly and sustainably reduced the copper losses in Gresik smelter to below 0.7%. A series of flow patterns evaluation in the CL-furnace demonstrated how the chemical reactions and settling conditions of the CL-furnace has been improved by the new operating procedures. Settling mechanisms for the matte droplets in the CL-furnace is also discussed using image analysis of solidified slag. INTRODUCTION The Mitsubishi Continuous Copper Smelting/Converting Process employs an electric furnace (CL- furnace) for settling the slag/matte mixture formed in the smelting furnace. Since the top-blowing in the S- furnace agitates the molten bath strongly, matte droplets are dispersed over the slag phase when melts flow out of the S-furnace. Thus, the CL-furnace has an important role to settle and recover matte droplets efficiently. Since many papers have ascribed major part of copper losses to matte droplets suspended in slag (Tanaka 2007; Genevski et al., 2008; Starodub et al., 2016), flow patterns of slag in the CL-furnace can affect greatly on the profitability of smelters which have adopted the Mitsubishi process. PROCESS DESCRIPTION Figure 1 illustrates the Mitsubishi process schematically. The Mitsubishi process is the only system for continuous production of blister copper from copper concentrates and consists of 3 furnaces connected by enclosed launders those ensure the minimum emission of fugitives. In a smelting furnace (S-furnace) copper concentrates are fed with flux, oxygen-enriched air to form a mixture of slag and matte which cascades down to a slag-cleaning furnace (CL-furnace). The CL-furnace settle matte droplets in the mixture on the crucible from which matte is siphoned to a converting furnace (C-furnace), while discharging the cleaned slag (CL-slag). The C-furnace converts matte to blister copper by the top-blowing of oxygen- enriched air.

Jan 1, 2019

By M. Fairclough, B. Moldovan

Insights into uranium mining projects of the future can be gained by a careful statistical analysis of past and present deposits, as well as an examination of recent trends for uranium resource evaluation and primary uranium production. The International Atomic Energy Agency (IAEA) provides the necessary data and corresponding mechanisms as inputs for methodologies that enable strategic and scientific evaluations of long-term security of supply uranium required to sustain the demand for nuclear fuel. Sustainability of the uranium mining industry and subsequently new uranium mines of the future requires innovation and expertise to lower operating costs, maintain or improve uranium recovery while meeting the requirements of stakeholders in regard to protection of the environment and safety of the workers and general public.

Jan 1, 2020

By M. Krasowska, K. Malysa, M. Krzan

The paper presents fascinating, in our opinion, observations on mechanism and course of processes occurring during bubble collision with hydrophobic and hydrophilic solid surface. Hydrophobicity of particle surface is a necessary condition for the particle attachment to bubble. We have observed that even in the case of such hydrophobic solid surface as Teflon, the bubble attachment didn't occur at first collision. In distilled water the bubble bounced a few times without attachment. Influence of a-terpineol and n¬pentanol on bubble local and terminal velocity and the phenomena occurring during bubble collisions with hydrophobic and hydrophilic solid surfaces was studied. Bubble collisions with the solid surfaces were monitored and recorded using the high-speed (1182 frames per second) camera. It was found that in distilled water the velocity variations of the "approach-bounce" cycles were identical for Teflon and glass. Four distinct "approach-bounce" cycles were detected both at Teflon and glass surfaces. Moreover, the amplitude and frequency of the velocity variations were identical on collisions with the hydrophobic (polished) and hydrophilic surface. There was no immediate three phase contact formation, with the hydrophobic Teflon surface, what we found really astonishing. Roughness of Teflon surface seems to be important parameter, which affects probability of the bubble attachment as a result of a presence of micro-and/or nano-bubbles at the surface. It was detected that the presence of the micro-bubble affected attachment of the colliding bubble even in distilled water. Presence of a small amount of a-terpineol or n-pentanol affects dramatically the bubble velocity, but their role in mechanism of the bubble attachment needs further study.

Jan 1, 2004

By Roger C. Parsons

"The problems presented by ice formation and interference with processes, structures and mechanical operations in the mining industry can be expected to increase sharply as more of our mineraI needs are supplied from the far north. A process of rapid ice destruction is presented which lends itself to the effective removal or penetration of ice. Suggestions are offered for applying the system to problems related to mining activity in cold environments. The system can be readily adapted to large-scale operation, the reactant components being transported in crystalline form and volatilized on site.IntroductionThe number of operational mines in northern environments, relative to the number of mines in the temperate zone, will increase in the years ahead. This is not surprising, because:(a) in the past, those mines closest to centres of commerce had minimum transport charges and hence were more economic to develop;(b) great centres of commerce were far removed from northern environments;(c) the exhaustion of ores and lowering of grades in temperate zones now offset to some degree the extra transport costs applied to northern ores;(d) the abundance of excess energy in the north in the form of oil, gas and hydropower attracts mining as a means to justify its development; (e) assuming that the frequency of mineral occurrence north of the 52° N latitude is no different than south of it, there are many deposits waiting to be developed.As a result of current and projected activity in northern environments, we are faced today, and will be increasingly so in the future, with mining problems rarely encountered before-problems related to below-freezing temperatures. Engineering activity in permafrost regions will increase as new mining ventures are developed north of the 52° N latitude, roughly coinciding with the -1.1 ° C isotherm in Labrador, the upper temperature boundary for permafrost."

Jan 1, 1982

By J. A. E. Bell

"Inco has shifted part of its traditional extractive research effort at its J..Roy Gordon Research Laboratory in Mississauga toward new, value-added products. Most of the effort is being expended on new Ni powders for batteries and new Ni-coated products which will be produced in Inco's carbonyl nickel refineries. New products under development are Ni-coated powders, Ni-coated fibres and ultra-fine Ni powders. Other new products for advanced material applications include controlled expansion composites, NiGOLD strip, Thermal barrier coatings on Inco alloys, and plasma coatings.Research and Corporate Strategic ThrustsThe newest strategic thru st of the company is to increase the value of the primary metal products. These new products are to be in addition to any new alloys or downstream alloy fabrication.Historically Inco has had the highest research expenditures in the extractive metallurgy field in North America. This has resulted in many new processes including flash smelting , matte separation, fluid bed roasting, pressure carbonyl refining and cobalt electrowinning which have contributed to establishing Inco as the lowest cost nickel producer. The recession of the 1980s caused a restructuring of Inco research and corporate goals .As shown in Figure I, from 1975-1982, i.e. pre-recession, Inco spent around 33 million dollars per year on research. Some 48070 of that sum was spent in Corporate Laboratories in Sterling Forest in the United States and in the United Kingdom , mostly on alloy associated research. A further 10% was spent on alloy research at the alloy production facilities in Hunting- ton, West Virginia, and Birmingham and Hereford in the United Kingdom. On extractive research, 13% was spent by process technology groups at the plant s, 20% at the pilot plants in Port Colborne and 9% at the J. Roy Gordon Research laboratory.The relative research expenditures (Fig. 2) have decreased so that today they are at the same level as 1975-80. The research as a per cent of sales has been cut from 2.2% to 1.2% of normalized sales. A normalized sale price of $4.00/lb Ni was used in the 1988 figures. This was partly achieved by closing Corporate Laboratories. Most of the essential alloy research was moved to producing plants and total alloy research is now 27%.A new thrust initiated in the 80s was mining research which now accounts for 20% of research expenditures. Over a period of the past five years this research has doubled the mining productivity in Inco. The pilot plant expenditures have been cut in half. One entire research station at Port Colborne was converted into a platinum group metals intermediate refinery. The decrease in pilot plant expenditures has been compensated by full scale plant trials devoted to the S02 abatement program at Sudbury."

Jan 1, 1990

By Klau Meyer

"At Teck-Corona Operating Corporation's David Bell Mine, a successful water quality management strategy has been established. This resulted from the development and application of process technology, allowing year round discharge of an effluent exceeding the chemical and biological standards set by the Ministry of Environment. This strategy aims at minimizing contaminant levels of effluents through optimization of reagent selection and reduction of effluent volumes through maximizing reclaim water usage. Concentrator and effluent treatment plant operating practices, process chemistry and the results of the water quality management strategy are reviewed.IntroductionThe David Bell Mine is located in the Hemlo gold camp 42 km east of Marathon, Ontario. The concentrator has a design throughput of 1000 tonnes per day. The processing of the run of mine ore ( - 15cm) involves the following unit operations: grinding in a semi-autogenous mill followed by a ball mill, thickening, pre-oxidation , cyanidation, and carbon-in-pulp gold recovery followed by electrowinning and refining.The David Bell Mine water quality management strategy is composed of the following items (Goodfellow and Meyer, 1991):• natural destruction of cyanide contained in the tailing water in a large shallow tailing pond ;• preliminary treatment of reclaim water in the grinding circuit for cyanide and heavy metal removal;• pre-oxidation of sulphide minerals in pipe reactors to reduce cyanide consumption using pure oxygen;• pH control in the grinding, pre-aeration and leach circuits to minimize the dissolution of stibnite while maximizing gold recovery; • close control of cyanide addition rates to the leach circuit to maintain the lowest possible levels;• a carbon column for gold recovery;• an effluent treatment plant for antimony and heavy metal removal; and• the use of final treated effluent for industrial water underground to minimize fresh water consumption."

Jan 1, 1992

By S. Zakaria

"Inco's Automated Haulage Truck System (AHT) is a revolutionary automatic guided vehicle that performs all load, haul and dump operations without human intervention. The high level of sophistication and the short period it has been in operation has only allowed a select few Inco personnel to become familiar with the ART operation and maintenance. As an aid to operations an expert system using the knowledge gained from the experienced specialists was implemented in the field.The AHT operating and maintenance assistance expert system will reason through the information given, arrive at conclusions and give advice to operations, technical and management personnel. It will provide comprehensive real-time troubleshooting assistance for the hydraulic, electrical and mechanical subsystems of the ART. The ART expert system has many benefits to Inco which include increased skill levels of ART operations and maintenance personnel, reduction in ART downtime, standardization of troubleshooting procedures and reduction in ART operating and maintenance costs. In the future, the expert system application will be linked to SCADA (Supervisory Control and Data Acquisition), maintenance and statistical software to display current and historical trends of variables from a centralized historical database. As well, a wide variety of features will be integrated into the system including AutoCad drawings, graphics, photographs, voice and video capabilities."

Jan 1, 1994

By K. Ilankoon, I. M. Saman, S. J. Neethling

In heap leaching the transport of the acid from the drippers to the surface of the ore particles is a major factor in the overall performance of a heap. This flow behaviour is complex as the flow is unsaturated and occurs along a tortuous set of inter-particle channels and connections. The particle properties such as size, shape and porosity are very important when modelling the liquid holdup and flow within heaps, since the dominant mechanisms at work are quite different. This paper investigates the effect of these particle properties experimentally on heap flow behaviour using a 1-D column leaching system consisting of non-porous glass beads with a system of actual ore particles. The similarities and differences between the two systems on flow behaviour are described using an inter-particle flow model. In addition, the applicability of positron emission particle tracking (PEPT) for laboratory column leaching will be detailed to calculate hydrodynamic dispersion in packed beds compared to more conventional residence time distribution (RTD) tests and also to obtain the time averaged rivulet flow paths through the particles of the bed for the better understanding of heap hydrodynamics.

Jan 1, 2014

By D. O. Tansey

This paper will describe the mechanisms involved in delay blasting and how they are applied with the use of D.S.B. It will examine the control of potential damage resulting from detonations, and show how good fragmentation and efficient recovery of this material blasted can be achieved.

Jan 1, 1979