Search Documents

By Alexandre Desbarats, Michel David

"All optimum pit design studies start from the geological are reserves inventory, the estimated grades of all blocks of potential are within the interpreted limits of the deposit. The actual optimization procedure is then carried out on block valuations based on these estimated grades. Thus, the relevance of any pit design can be seen to depend directly on the ore reserve estimation . To insure a proper pit design, a first step would be to use a geostatistical reserve estimation technique such as kriging, however, this is not enough. A frequently neglected fact is that the blocks of ore estimated during the planning stage of the mine are usually considerably larger than those on which the ore-waste selection will be made at the time of mining. Experience in the exploitation of large low-grade deposits has shown that large blocks, estimated to be are, when mined selectively in smaller blocks, often yield significant amounts of waste material. This phenomenon, known as internal waste, is a function of the variability of the grades, the size of mining unit and the amount of sampling information on which ore-waste decisions are made.In this study, it was proposed to consider the effect of internal waste caused by selective mining, on. pit design, using geostatistical methods to predict the tonnage and grade of recoverable reserves within large blocks.Optimum pits obtained using a block valuation formula taking into account the recoverable reserves within large blocks were compared with optimum pits obtained using a conventional block valuation formula. It was found that the optimum pits obtained by the proposed method had the highest total valuations and thus were, in fact, ""more optimum”. These pits were characterized by greater are tonnages at a lower average grade, the additional ore more than compensating for the drop in grade. It was also found that the consideration of internal waste in pit design could considerably alter pit limits in marginal areas of the deposit.It was concluded that selective mining had a significant, potentially critical, impact on the design of optimum pits especially in the case of large low-grade deposits."

Jan 1, 1984

By China University of Mining & Technology, Yuemin Zhao, Bo Zhang, Liang Dong, Zhenfu Luo, Chenlong Duan

"In China, approximately 65% of coal reserves are in the west region, where water shortage is a serious problem: high-efficiency dry coal beneficiation technology is desired. Using magnetic powder and fine coal as heavy medium, and using air as the fluidizing agent, a novel air dense medium fluidized bed separator is proposed for coal preparation. Coal can be efficiently separated according to density in the fluidized bed, where bed density is steady. The separator is highly reliable, the circulation quantity of heavy medium is low, and the gas distributor cannot be easily easily. The world’s first industrial modularized dry coal preparation plant was built by China University of Mining and Technology. Dry coal beneficiation technology was first used to produce low-ash coal. Results of industrial production show that the ash content of clean coal is 3.46%, the probable error E value is 0.055 g/cm3, and the organic efficiency is over 90%. The advantages of the modularized dry coal beneficiation system are the high separation accuracy, the simple process flow, the low operation cost, low energy consumption, and so on. This technology provides a new effective method for coal separation in acid region and coal tending to sliming.INTRODUCTIONCoal is the most important primary energy source in China, where coal output reached 3.68 billion tons in 2013 and represents approximately 68% of the primary energy consumption. Coal has made a great contribution to the development of the Chinese national economy, but it also brings serious environmental pollution. However, approximately 65% of coal reserves are in the arid west region in China where water shortages present a challenge for wet coal preparation technology. In addition, the abundant lignite resource, because it is easy to mud in the water, should not be treated with the wet separation method. Therefore, it is critical to develop highly efficient dry coal preparation technology to meet the demand in arid areas. Further, water resource shortages are a global problem, thus the development of efficient dry coal preparation technology in has potential application in other water-short countries like South Africa, Brazil, India and Turkey."

Jan 1, 2016

By A. Diaz, Minera Los Pelambres, C. G. Salinas, G. Leinenweber, F. Diaz, D. Rojas, R. Bernal, O. Jimenez

"Los Pelambres Mine (MLP) is located in the IV Region of Chile, a semi-arid region where water plays a key role in operations as a scarce resource and is vital for the sustainability of human life, animals and ecosystem. The conventional flow meters installed on pipes at MLP can fail to provide an accurate measurement due to corrosion and/or fouling on the inner wall or presence of elements in the water such as acids, salts and suspended solids. Conventional flow measurement methods require the inner diameter to be known, however it is not always possible to assess its real value due to scaling, fouling, corrosion, etc. Here we present a novel methodology to solve these problems, which consists of the measurement of flow by a method that does not require the internal area of the pipes: the fluorescent tracer dilution method. In addition, the fluid velocity can be determined by the transit time of a radioactive tracer method. With the flow rate and velocity, the equivalent area is determined and thus the equivalent internal pipe diameter as well. This methodology was applied in a recirculation pump station, for mineral processing from the El Mauro tailings dam.This work demonstrated adequate correlation between measurements from fluorescent tracers and velocity measurements from radioactive tracers, both of which lead to the assessment of the internal diameter of pipes with scaling. The results of both methods disagree with the data provided by the flowmeter installed on the line due to its miscalibration. This information is useful in validating and correcting the information provided by online flowmeters of all water and solutions transport processes in filled pipes.INTRODUCTIONPresently, the need to optimize water resources is increasingly ever important, due to various reasons such as water scarcity, community empowerment, an increased use of water for mining processes and environmental considerations. Taking into account those main considerations, Los Pelambres Mine decided to focus on water conservation to avoid losses of this vital element. They decided to demonstrate that all of the systems that used water (flow meters, pipes, pumping stations, lagoons, etc) were in good condition and that no evitable loses of this important resource occurred. A plan was proposed to conduct a “hydraulic assessment” of fluid flux and water speed at different points and courses at the mine, with the purpose of obtaining hard data to support, verify and correct the information provided online from specific instrumentation dedicated to those purposes. The final goal was to manage the water resource basin in a sustainable way, based on cross-checked information. The chosen points are representative of the processes present in the mine, such as recirculating water stations at different operating conditions and surface water courses, where the fresh water capture systems operate."

Jan 1, 2016

By C. H. Stockwell

THE Eastern Townships of Quebec have been the chief Canadian source of chromite. Production, however, has never been large and, except for a period of steady but small output between 1894 and 1909, mining has been active only in war time. The known deposits are too small or too low grade to compete with overseas sources in normal times. During the last war, shipping difficulties and a greatly increased demand in the United States resulted in high prices and a ready market for low-.grade material. The Quebec chromite industry flourished and played an important part in relieving the wartime shortage. Shipments in 1918 .amounted to 15,600 tons of crude ore and 6,400 tons of concentrates. At the outbreak of the present war it was natural to turn again to the Quebec field as a possible source of this strategic mineral. Some of the old properties have since been opened by private and government money and some new deposits have been found. Total mill capacity is 750 tons per day, as compared with 200 to 300 tons in 1918. During 1940, 1941, and 1942, about 85 chromite deposits were examined by the Geological Survey in a belt 100 miles long and up to 7 miles wide. A part of this belt, about 35 miles long, in which the geological features ?were not well known, was mapped on a scale of 1/2; mile to an inch.? Small ..areas around some of the deposits were mapped in detail, on scales of 20 to 200 feet to an inch. Some geophysical work was done but did not result in the discovery of ore. Prospecting by stripping and trenching was then undertaken and chromite ore was uncovered at several localities. The above work was done by the writer and by J. W. Ambrose, who has kindly contributed his results for incorporation in this paper. Y. O. Fortier actd as assistant in the geological work and, in 1942, was in charge of a sub-party engaged in geological mapping. The author is indebted to H. C. Cooke and J. W. Ambrose for reading the original manuscript and for offering many helpful suggestions for its improvement.

Jan 1, 1944

By J. Gebhardt, D. McBride, C. R. Bennett, Croft. N., M. Cross

A comprehensive model of solution flow through heap leach systems requires a numerical solution with the ability to predict variably saturated-unsaturated flow through porous media domains that contain materials with spatially variable properties. The types of flow associated with stockpile leach processes lead to flow problems, such as infiltration into dry soil, drainage, perched water tables and flow through heterogeneous materials. Computational methods for modelling this class of flow behaviour are conventionally based on the classical Richards' equation. However, the governing equations are highly non-linear, difficult to solve, and require iterative numerical solution methods. The pressure-based form of the Richards' equation suffers from poor mass balance, while the mixed form can possess convergence difficulties. An adaptive transformed mixed algorithm is described, which reduces the non-linearity of the problem, optimizes the time step size, and provides a fast, numerically robust scheme that significantly reduces computation (or CPU) time. This method is shown to give fast, accurate solutions on a number of complex flow problems. The utility of this algorithm is illustrated through its implementation within the PHYSICA computational modelling software, which incidentally, provides a framework for a comprehensive heap leach model.

Jan 1, 2005

By Stephen Hardcastle

Personnel Heat Exposure Issues In Canada?s Deep Mechanized Mines ?Project developed in 2004 ?Base/precious metal industry identified heat stress/management as a major challenge affecting productivity and operating costs ?Project started in 2005 ?Current research nearing completion ?Guidelines, further data analysis and ?Communicating the Science? will continue into 2011 Managing Heat Exposure Control?. The cost implications ?Controlling the environment ?Ventilation already a major expenses/energy user ?Large Canadian mines are currently delivering massive volumes of air 15-20 tons of air/ton ore ?Large investments in ventilation upgrades, mechanical cooling

May 1, 2010

By R. M. Bustin

"Extensive deposits of tectonically sheared coal of the Mist Mountain Formation occur in the south eastern Canadian Cordillera. The quality of the coal varies markedly; it is commonly partially oxidized and poor washability characteristics.Oxidation of the sheared coal has been promoted by its fine grain-size and by fractures in adjacent rocks which have facilitated penetration of atmospheric oxygen and circulation of oxygenated waters. Oxidation has resulted in a loss of coking power, a decrease in vitrinite reflectance, and an Increase In oxygen and decrease in carbon content.The relatively low clean coal yields of the sheared coal are primarily the result of the greater volume of mineral matter present, which in turn reflects both the greater susceptibility to shearing of coal with abundant rock partings and the shearing and dissemination throughout the coal of formerly discrete rock partings. The high ash content of some sheared coal seams may be artificial, resulting from the difficulty in distinguishing and separating sheared roof rock and floor strata from the coal seam during mining. There is little variation between the quality of the washed sheared and unsheared coal, with the exception of the somewhat higher ash content of the clean sheared coal compared to clean unsheared coal. This poorer separation of the ash from the organic fraction of the sheared coal is considered to be a product of the large amount of fines present as well as the local formation of aggregates of organic material and ash resulting from plastic flowage of the vitrite and clarite during shearing.IntroductionIn the southeastern Canadian Cordillera, coal seams of the Lower Cretaceous Mist Mountain Formation (Gibson, 1979 were in part sheared and comminuted during Late Cretaceous and Tertiary tectonism . Extensive deposits of sheared coal exist, and even in areas of mild deformation the coal may be locally sheared (Bustin, 1979). The quality of the sheared coal varies notably; it is commonly oxidized even far from the present weathering horizon, and locally has a disproportionately large amount of ash and poor washability characteristics even far from the present weathering horizon and locally has a disproportionately large amount of ash and poor washability characteristics."

Jan 1, 1982

By Törbjorn Naarttijärvi, Bengt Ludvig, Agne Rustan

"Falling rock is one of the major causes of serious injuries and deaths in Swedish mines. The research at the Division of Mining and Underground Construction was therefore directed toward controlled blasting in hard intense jointed rock.The project was started with an extensive literature review. Model tests with a new equivalent model material have been initiated to find ways of improving blasting techniques. The result showed that long cracks arise at the perimeter holes when there is a long time delay between adjacent holes. This led to the theoretical development of a new initiation method with ultra short delays (1,5 ms) f or controlled blasting, called ""Cutblasting"".Full-scale tests have been done at LKAB in Malmberget in hard intense jointed magnetite ore. Four different types of perimeter charges have been tested, namely: tube charges, ANFO mixed with plastic beads, detonating cord and linear shaped charges. Three types of initiation of the perimeter holes have been used, conventional (half-second delay detonators), instantaneous and ultra short ""cutblasting initiation"" (1,5 ms delay). The change in rock strength before and after blasting has been studied with bore hole periscope, vibration measurement and ocular observation of the rock surfaces.Thefull-scale tests showed that ""cutblasting"" with detonating cord in the perimeter holes gave the smallest damage to the surrounding rock. A combination of cutblasting initiation and tube charges are anticipated to give an even better result. A new method of controlled blasting using linear-shaped charges has also been tested, however, this charge type needs further development.The full- scale test also showed that the damage which can be seen on the rock surf ace is about the same for different controlled blasting methods but the not-visual-damage zone varies as much as from 0,1 to 0,7 m.A new classification system for controlled blasting regarding the damage to the surrounding rock has been devised."

Jan 1, 1985

By W. Dresler

"A major Canadian chromite deposit at Bird River, Manitoba is one of the largest known chromite reserves in North America but it exhibits low chromium contents and low chromium to iron ratios. Commercial beneficiation techniques permit these ores to be upgraded to concentrations which, however, remain inferior to most other ores and concentrates used worldwide f or production of high-carbon ferrochromium. Analyses for reduction of low-grade concentrates by submerged-arc electrofurnace techniques predict chromium contents between 45.9% and 51% for a high-carbon ferrochromium alloy. Relatively high over-all chromium recoveries between 79.5% and 91. 1% can be achieved. Alloy compositions for Cr, Fe, C and Si are determined for various burdens with low-grade concentrates. Consumption data per ton contained chromium are obtained for electric power, coke, concentrate, quartzite and limestone. The data are compared with those of high-carbon ferrochromium producers in South Africa. Economic aspects are discussed and compared with a South African reference study.IntroductionThe present ferrochromium demand in the western world is estimated at approximately 1.7 Mt with a consumption of approximately 0.36 Mt in the U.S.III and 0.03 Mt in Canada'-', A low estimate of the installed production capacity for ferrochromium in the non -communist world is 2.4 Mt. This production capacity of ferrochromium by far exceeds the demand, which is also evident from the fact that no shortage in supply of ferrochromium to the world markets was encountered in the past. Supply-demand comparisons therefore suggest that in the foreseeable future no new chromite or chromium producers should enter the world markets unless superior chromites or superior technologies are successful in competing with existing producers. Neither one of these conditions exist presently in Ca nada or the U.S., although essentially no ferrochromium is produced and no chromite is mined in these countries at the present time."

Jan 1, 1986

By Matthew A. Baumann

Tooth wear on mining shovels presents a challenge for productivity. A shovel with worn teeth suffers from increased digging forces, longer fill times, and an increased likelihood of lost or broken teeth and adapters. Efficient maintenance planning relies on knowledge of tooth decay rates and patterns. A fully automated wear monitoring system can record detailed logs of tooth wear, permitting G.E.T. personnel to optimize maintenance scheduling. Studies have demonstrated that planned tooth change-outs result in significantly reduced costs as compared to unplanned maintenance. A machine-vision-based tooth-wear monitoring method is introduced. A rugged camera is installed on the boom of cable shovels, or on the stick of hydraulic shovels. The images are processed using a photogrammetric algorithm to determine the individual tooth lengths. Tooth length data is collected at intervals during shovel operations, forming a profile of the current wear state, speed of decay, wear pattern, and expected lifespan of teeth. A case study in a South American mine on a Komatsu PC8000 hydraulic front shovel is presented. Tooth wear is tracked over a 6-day period and wear rate statistics are computed for 6 teeth. This validates the system and provides an example of how wear patterns can be recorded and analysed by an automatic system. Armed with this data, mine personnel can reduce the cost and lost time due to unplanned maintenance, and observe the effects of mine conditions and operator behaviour on tooth wear.

May 1, 2011

By Ronald E. Pike

"PREFACEAt the CIM Annual General Meeting in Quebec City, R.E. Pike of The Toronto-Dominion Bank described how the Canadian banking industry worked with the minerals industry to assemble the large capital requirements for resource projects in Canada and overseas. He developed a profile of the mining industry and Canadian banking, both being important sectors of the Canadian economy and global in context. He also outlined the banking and financing partnership that existed in the past. In looking to the future and challenge that lies ahead f or each industry, Mr. Pike questioned whether the financing practices of the 1970s will be acceptable over the next decade. In that regard, he highlighted the risks that impact on each industry and illustrated how that financing partnership might evolve in response to those forces. The folio wing is a synopsis of his paper.IntroductionThe Canadian mining and metals industry is prominent in the domestic economy and respected internationally. Any measure of its performance illustrates that status-percentage of GNP, employment, exports, capital investment, size relative to other producing nations, etc.Energy, Mines and Resources Canada has forecast that the non-fuel minerals industry will grow in real terms by an average annual rate of 3.0% over the period 1981 to 1991. Using the GNP as reference, that growth in non-fuel mineral production will represent 7.7% of GNP. In translating that growth to capital expenditure, the EMR Canada estimates the aggregate amount at $43.8 billion ('79 dollars) or approximately 12% of total business investment in Canada during the 10-year period.About half of the $43.8 billion will be devoted to the ferrous sector-$8.4 billion in iron ore mining and $12.4 billion in the steel industry. Capital investment in nonferrous s projects is estimated at $13.3 billion, and it is projected at $6.7 billion for industrial minerals. The residual $3.0 .billion is exploration spending."

Jan 1, 1982

By A. Chieregato, C. G. Oñate Salazar, D. Martinelli, D. Peila, M. Barbero

This paper is aimed to confirm the possibility to excavate fractured rock masses by using EPB shields, even in presence of relevant water tables. This verification is based on laboratory test experiences carried out at TUSC laboratory of Politecnico di Torino, where the natural material is tested in order to verify the suitability of a certain conditioning technique in particular conditions. This is due to the fact that every case should be studied apart from existing studies on a certain rock type, as other factors such as fragmentation of the rock mass, natural water content and porosity of the rock can considerably influence the final result of the conditioning process. The most important aspects that allow to consider the conditioning of fractured rock masses as suitable are: possibility to create a plastic paste that can transmit the pressure at the front in a effective way; reduce the permeability of the spoil material in order to reduce the possibility of water leakage inside the chamber and eventually in the tunnel; verify the consistency of the conditioned material for the extraction through the screw conveyors and the belt conveyors. For this research an argillitic schistose rock mass, with some quartzitic and calcareous inclusions, has been studied by using different level of conditioning in order to verify the suitability of an eventual EPB excavation through this formation.

Jan 1, 2015

By Martin Wacker

Cameco Corporation, on behalf of a joint venture, is preparing surface and underground facilities at their northern Saskatchewan property in preparation for the future operation of a high-grade uranium mine. The Cigar Lake orebody is situated about 430 metres below surface at the unconformity between metamorphic basement rocks and flat lying sandstone. Major technical factors influencing the mining method selection include ground stability, control of ground water, radiation exposure and ore handling and storage. A decade-long test mine program resulted in the selection and validation of ?jet boring? a non-entry mining method. Cigar Lake?s jet boring mining method involves several major steps; artificial ground freezing of the orebody and surrounding rock, TBM (tunnel boring) type development of access crosscuts below the orebody, installation of cased pilot holes upwards through the ore, and ore extraction using a rotating high pressure water jet within the pilot holes. The resulting cavities are surveyed and backfilled with concrete. The ore slurry will be processed underground and pumped to surface. This paper discusses the jet boring mining method in general terms and includes highlights of the Cigar Lake test mine program completed in 2000.

Apr 1, 2005

By X. -P. Zhang, L. N. Y. Wong

Shale gas exploitation initiated in North America has rapidly extended worldwide. Hydraulic fracturing is an emerging field technique for stimulating the gas reservoir. The study of cracking processes, particularly crack coalescence, is vital for a successful hydraulic fracturing to enhance the gas exploitation. Experimental studies have observed that the size effects of the constituent particles are significant on the cracking behavior of the rock specimens. To further investigate the size effects, the bonded-particle model (BPM), which is based on the discrete element method (DEM), is adopted in the present research. In flaw-containing specimens, by varying the crack resolution (?= a/2R), which is the ratio of half flaw length (a) to particle size (2R), the size effects on cracking behavior under compressive loading are studied. By keeping the flaw length constant, the particle size is varied independently in the BPM analysis. Decreasing the crack resolution increases the first crack initiation stress, but it has no obvious effects on the uniaxial compressive strength. The trajectories of the first cracks and secondary cracks hence generated have a higher resolution and are well-defined in those specimens possessing a higher crack resolution. On the contrary, in lower crack resolution specimens, the macroscopic first cracks appear to be wider and less continuous. These findings from numerical simulation clearly demonstrate particle size effects on cracking behavior. Special attention should be paid to these effects in future numerical study using the bonded particle model.

Jan 1, 2015

By S. Avalos, J. M. Ortiz, W. Kracht

Semi-autogenous grinding mills are intensive energy consumers. Current models base their energy consumption inference on operational variables and feeding ore characterization. While they provide adequate design guidelines, they are not suitable for real-time energy forecasting dealing with gaps in operational dataset and up/downstream process bottlenecks. This work explores the capability of Gated Recurrent Units to learn the semi-autogenous grinding mill consumption behaviour. Gated Recurrent Units are trained to forecast different time-support consumptions under a time-series operational dataset. The results show high performance on small supports (30 minutes) to capture local variability and long-trends while larger time supports (8 hours) can only capture time-trends but not local variability. The proposed technique seems promising for further research and implementation on real mine cases since the input variables are low-cost and easy to obtain. INTRODUCTION Current changes in the Chilean energy matrix (Román-Collado, Ordoñez, & Mundaca, 2018), from fossil fuels to renewable energies, have impacted different industries and particularly the mining sector. Solar energy incorporation into greenfield/brownfield projects will help reducing costs and will lead to rethink foundational paradigms (production and processing strategies) (Pamparana et al., 2017). Also, integration of new space-time predicting tools together with automated real-time updating models are some of the main challenges in the geometallurgical framework (Ortiz et al., 2015; van den Boogaart & Tolosana-Delgado, 2018). Those contexts encourage and demand the development of tools capable of predicting the energy consumed by mining systems, being comminution the greatest energy consumer with an average close to 50% of the entire mine consumption (Cochilco, 2013). In comminution, the semi-autogenous grinding mill (SAG) represents the largest energy consumer (~10 nominal each SAG). Theoretical and empirical energy consumption models (Jnr & Morrell, 1995; Morrell, 2004; Silva & Casali, 2015) base their inferences mainly on feed/product size distributions, SAG sizing, bearing pressure, feed hardness, water addition and grinding charge level, and commonly assume steady-state and work isolated from up and downstream processes. While those techniques provide adequate design guidelines, they are not suitable to predict hourly, daily or even weekly energy consumptions on interconnected comminution circuits where upstream/downstream bottlenecks lead SAGs to operate below designed regimes. Forecasting energy consumption is required by short-term energy management, medium and long-term planning energy consumption, designing the nominal capacity of renewable energy sources, among other. Also, when models are input-sensitive and some of those input measurements are expensive and/or time consuming, model robustness suffers when real-time predictions are required.

Jan 1, 2019

By W. Yang, R. Rajasingam, K. Mohanarangam

"Copper Electrowinning (EW) is a complex electrochemical process that involves the production of LME grade copper from copper rich electrolyte. The process involves the deposition of the copper ions onto the cathode from copper rich electrolyte with the production of oxygen bubbles at the anode. The process setups up a complex flow pattern within the cell as it is subjected to varying density gradients due to the deposition process along with oxygen bubble driven flow. It is a necessity to understand and quantify the flow behaviour within these cells in order to maintain the production of highest grade copper. In fact, the oxygen bubbles originating from the process is responsible for the generation of acid mist which is a designated as a carcinogen a major health hazard around EW tank houses. Hydrodynamic assessment of the process has so far been restricted to simple mass balances and some limited numerical modelling. All the models are based on assumed boundary conditions which has not so far been verified by any real-time physical measurement. This apparent gap has led to models which could not be directly used to track process changes or troubleshoot problems in EW tank houses. In order to address this gap, CSIRO has established a full size (width and height) transparent cell capable of simulating plant operating conditions (across the range currently used). With the use of sophisticated diagnostic analytical tools and measurement techniques it was possible to study all the operating variables (current density, flow rate, temperature, etc.) independently and their effect of bubble size, bubble velocity, gas hold-up as well as acid mist generation and its size. In order to address safety concerns in tank houses around acid mist early results outlining the factors contributing to its generation as well as the effect of various barriers to mitigate acid mist is outlined below.INTRODUCTIONA significant part of today’s copper production is through hydrometallurgical route which predominantly involves leaching, Solvent eXtraction (SX) followed by ElectroWinning (EW). Producing copper using this approach have shown to be environmentally friendly (Dresher, 2001) compared to the traditional smelting process. EW is the final step in the production of LME grade copper using the hydrometallurgy route. The electro-chemical process involves the use of a lead anode (Pb-Sn-Ca) and a stainless steel cathode to produce copper sheets using the copper rich electrolyte from the SX process and with the applications of direct current to the electrodes. This electro-chemical reaction results in the deposition of copper ions on the cathode with oxygen released from the anode as a by-product. Hydrodynamically, the oxygen bubbles create a bubble driven flow within the EW tanks with the surrounding electrolyte. A direct result of this could be seen from the quality of the copper deposited on the cathode. Most of the copper plates produced from the traditional tank houses have a rough texture at its bottom one-third while the top two-thirds have a smooth finish with a finer grain structure."

Jan 1, 2016

By M. R. Henzinger, G. Lenz, A. Gaich, Pötsch, W. Schubert, P. Wagner

"The better the information on the rock mass and its fracture system, the better is the basis for any rock mechanical decision that is required during the excavation process. While in conventional tunnelling free view to the tunnel face is available, possibilities are limited for mechanised tunnelling using a tunnel boring machine (TBM). An approach, already formulated in 2005, is used that produces digital photographs through openings in the cutting wheel of a TBM and merges them into a circular three-dimensional image. The 3D image is then used for geometric rock mass characterisation purposes including geological mapping, for example to measure spatial orientations or determine joint spacing. In the paper the basic concept is described together with first results from a pilot test.INTRODUCTIONA three-dimensional image unites digital photographs with spatial information on the objects/surfaces it shows. Since they combine geometric and visual information they are a straightforward source for geometric rock mass analysis and geological mapping. Their obvious benefits among others are: (i) they allow spatial measurements even in inaccessible regions, (ii) they provide objective and reproducible records of the rock mass conditions, and (iii) they increase working safety (Gaich et al. 2004).Pre-requisite for the generation of 3D images is the acquisition of at least two photographs from the region of interest. From the photographs the imaged object surfaces are reconstructed by means of image analysis using methods from photogrammetry (Slama, 1980) and computer vision (Hartley & Zisserman, 2001). See also Figure 1."

Jan 1, 2015

By Kuwauchi. Y., M. Barati

Recycling of dust using a rotary hearth furnace (RHF) has gained considerable attention in the past two decades for the sustainable production of steel with less environmental impact. In order to further promote the recycling of electric arc furnace dust and carbonaceous wastes using the RHF process, a mathematical model was developed to predict the reaction behaviour of dust-reductant composites. The reduction kinetics of zinc and iron oxides as well as the volatilization behaviour of volatile matter in the reluctant were considered. The modeling approach and some preliminary results are presented in this article.

Jan 1, 2011

By P. K. Kaiser, F. Amann

"Rock mass characterization for deep underground construction and mining offers many challenges. This paper first describes some of the key challenges when characterizing highly stressed brittle rocks and then offers some guidance on how to arrive at reliable rock mass strength parameters for deep mining applications. Focus is placed on characterization for rock mass strength determination. It is illustrated how the common use of currently available rock mass characterization systems tend to underestimate the strength of rock at depth. Modifications to currently adopted approaches, i.e., the use of Geological Strength Index GSI for rock mass strength determination, are presented.INTRODUCTIONFor green fields projects, the first challenge of rock mass characterization stems from a lack of access to examine the rock mass at scales larger than typical core sizes (i.e., ~63mm in diameter) until late in the mine design when the flexibility for making changes is constrained. Hence, rock mass characterization often has to rely on information derived from boreholes alone (e.g., core, logs, etc.). This challenge is lessened when mines are expanded from existing operations. A second challenge is related to changing rock mass behaviour with increasing depth and stress. At depth, the rock is highly stressed, thus closer to failure, and often highly confined which leads to a higher interlocking with elevated strength but more brittleness. The goals of rock mass characterization are to be tailored to the technical goals of an investigation. For example, for cave engineering, the workflow includes the assessment of five key engineering aspects (Brown, 2007): Caveability; fragmentation; cave performance; extraction level stability; and mine construction (rock support). Each engineering aspect has to address specific engineering questions and each design component is influenced by different rock mass behaviour aspects and thus is dominated by different rock mass properties, e.g., the vulnerability to stress fracturing (spalling), the bulking characteristics for flow control and support selection, and the confining stress impact on pillar or support design. An effective rock mass characterization program, including logging, mapping and laboratory testing, thus has to collect and interpret features that are relevant for the above listed purposes. Some of the predominant factors are: block volume of defected and non-defected rock; spalling strength; tensile strength of defects; rock mass modulus; and rock mass strength parameters for application to low and high confinement design aspects."

Jan 1, 2015

By E. G. C Charlesworth, M. J. Robertson

"Gold mineralization in the Main Reef Complex at Sheba Gold Mine is hosted within shear zones in a sequence of shales and greywackes of the Fig Tree Group. Competency contrasts between these rocks and a steeply dipping chert unit provided a locus for the development of right lateral steeply dipping shear zones. A set of flatter dipping shear fractures crosscut these zones with their intersections defining a system of en échelon ore shoots. Mineralization is both of vein type and disseminated strata-controlled replacement type. The latter occurs mainly within the wall rocks to the shear zones. Arsenopyrite and pyrite are the major sulfides, with arsenopyrite being confirmed largely to greywacke beds and pyrite to the more iron-rich shale units. Gold was introduced, together with minor sphalerite, pyrrhotite, chalcopyrite and early arsenopyrite, toward the end stages of a first pyrite phase. The mineralizing fluids were introduced along dilated cleavage planes and, emanating from these, produced a series of replacement fronts. Mineralization was syntectonic to late tectonic and occurred under conditions of progressive deformation, resulting in sulfides which are concentrated in the hinges of shear-related folds and semimassive sulfides within tension fractures which are folded, attenuated and fractured. An analysis of the structures shows a sequence of events in which an initial ductile simple-shear event with a steep sense of movement was succeeded by a more brittle strike-slip event. Mineralization is temporally related to the latter. This evolution in structural style was probably related to reactivation of the Sheba Fault as a transcurrent fault during emplacement of large granitoid bodies."

Jan 1, 1994